Related
I have a Siemens SX56, locked to AT&T.
I downloaded the new 1.1 ROM, (Jeff's courtesy)
and began the upgrade.
It started, My SX56 said "Upgrading It will take about 5 minutes...."
Then,
I got an error message on my computer about com ports not being available, it lost the active sync connection, and now my SX56 is hung on the same message: "Upgrading It will take about 5 minutes....."
Of course, I'm unable to connect back.
Any suggestions?
I'm trying to be able to use it with T-Mobile.
I was unable to get any results by pushing the hard/battery resets.
Thanks!
"COM ports not being available"... Are you using ActiveSync via serial cable or cradle?
If you really cannot connect anymore, I guess you have to use an SD-card and the bootloader method to get back to a working state. But do try to reset the device and restart Programme A., it may just pick up again. I've seen that happen here once.
Try doing a soft reset then put it back in the cradle, the upgrade should restart automatically.
AlexF said:
I have a Siemens SX56, locked to AT&T.
I downloaded the new 1.1 ROM, (Jeff's courtesy)
and began the upgrade.
It started, My SX56 said "Upgrading It will take about 5 minutes...."
Then,
I got an error message on my computer about com ports not being available, it lost the active sync connection, and now my SX56 is hung on the same message: "Upgrading It will take about 5 minutes....."
Of course, I'm unable to connect back.
Any suggestions?
I'm trying to be able to use it with T-Mobile.
I was unable to get any results by pushing the hard/battery resets.
Thanks!
Click to expand...
Click to collapse
Hi Alex,
The same thing happend to me.Could you solve this problem?
If yes,can you pls.tell me: [email protected]
Brgds
rats
Were or are you using a USB hub? If so that may be your problem. The SD Card method works very well and very reliably. No comms outside of the device. I found many times whenn trying to do file xfers to the XDA that for no reason in the middle of transferring a file the connection would be lost.
I haven't had this problem with 2003 and AS 3.7.
USB Problem
Hi Alex and Rat,
i got same problem also, after step 4 my XDA screen become white and hang, if you already solve this problem please send me how to fix it this problem to [email protected]. Do you know how to install wallaby bootloader also.
My friend's jamin when he tried upgrading with smart1 wm6
after the flashing process finished it gives the 3 colors of boot loader
the screen flickers continously with the 3 colors
no way to hard reset the device
and activesync doesn't feel it
I searched all the forum for a problem like this but I didn't find any
any suggestion please, or any help?
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
NetrunnerAT said:
Flash NVID Rom and try Smart again. Read WM6 upgrade Manuel and readme for the ROM.
Click to expand...
Click to collapse
Please how can i flash with the activesync doesn't notice my device and where's NVID Rom
Ok. I'll search for it but please help how can I flash it to the device which doesn't recognized or felt by PC
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
divxmaniak said:
If your device is in bootloader mode, activesync cannot recognize it but this is normal. Jamin is recognize only as a usb device and you can downgrade it to NVID rom easly.
Then you could upgrade your favorite rom, I suggest PDAVIET 4.0.0.1
Bye for now
Click to expand...
Click to collapse
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
must use NVID rom. maybe qtek nvid one from here? http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
hasanemara said:
I think I didn't discuss the problem well
The Problem is when I start to flashing a rom a message tells that check if the usb is connected and if the device is connected .
This is happen with the device is connected to the cable and the tricolor screen is flicking . and the device doesn't open doesn't flashing.
Click to expand...
Click to collapse
If the problem still there, Try to release the battery for 1-3 hours and put it again to the device, go to the boot loader and pray. Hopefully it could work. Actually, this way worked on my Himalaya and Prophet.
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
ekto said:
Just run the "Step 1" component of the PDAViet ROM (http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip), which is just a plain AKU 2.20 NVID. This will find your device even if its in bootloader mode (it doesnt depend on activesync). Just flash it with that sucker and you should have a working phone on WM5, then you can safely upgrade it to WM6 (or leave it if you like).
Click to expand...
Click to collapse
I shall try and tell you the result
error 260 this is the result
i have a slight variation problem like this...
1. i was upgrading my O2 Neo to the latest WM05 & the phone went to bootloader mode & the upgrade started searching for the phone as normal..then some error & it stopped upgrading while the phone was in bootloader mode..
2. at that time,i got an urgent call & had to leave the phone in bootloader mode...
3. when i came back..the phone was dead & now it wont startup at all.. not even in the bootloader mode.
4. Maybe the batteries dead...so i charged it (Over night)..nothing happened in the morning..
5. kept the battery removed for about 5-6hours & still nothing happens..it simply does not startup.
6.I've tried holding the camera button & resetting, but it wont go into bootloader mode.
7. i;ve tried holding the connections button + camera button _ reset but it wont hard reset...
can anyone help me here...
what can i do???
hasanemara said:
error 260 this is the result
Click to expand...
Click to collapse
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
ekto said:
Error 260... If i remember correctly that's "cant find device" or something.
Few things to check:
Is the PC you are upgrading on running windows vista?
If so, use a different PC running windows XP.
Have you tried a different USB cable?
If not, do so, this tends to be the cause of problems like this.
Have you checked device manager?
Go to control panel, Administrative tools, computer management, device manager and see if you can find your device. If it has a yellow ! icon on it or is listed as "Unknown device" or anything like that then you may need to reinstall the drivers (int hsi case the easiest way to do that is to reinstall activesync). If everyhting is working properly it should show up as "HTC USB Sync", "PocketPC USB Sync" or something like that under the heading "Mobile Devices".
Have you just plain tried another computer, regardless of the OS?
I found that I could never get my phone to flash on my laptop, but it worked without a problem on my desktop. This is not to say laptop's cant do it, it simply means some computers just have problems like (in my case i believe) no USB 2.0, or too low-powered USB ports.
Click to expand...
Click to collapse
No I didn't change any and I can connect my o2 xda mini to the same cable
I want to ask few technical question
HOW CAN A SOFTWARE DAMAGE THE DEVICE?
CAN A SOFTWARE FOR EXAMPLE BURNS A PROCESSOR OR SOMETHING LIKE THIS?
If So there will be a big problem with those types of devices
a virus for example can destroy my device's board or processor!!
Yesterday My friend went to an I-mate customer service who tel him that
the board had been destroyed by the bad software !!!!!!!!!
Please Give me technical advice about this problem
and is there a web site for him to buy this board (i-mate jamin)?
I've tried everything... even tried it on my desktop... but my phone just wont turn on now. i've kept the battery removed for more than 8hrs now... i've even charged it for more than 8hrs non-stop..nothing happens..
maybe i should get hold of a charged battery & try it with that battery...?
Any clue how to get my phone started??
got it working !!! PHEW... i used my HP battery which was charged & put it into it..now i've got my bootloader & i'm installing the new OS as we speak... 15% done.... keeping my fingers crossed
done.. got my HP Ipaq battery , which was charged & my new started up in bootloader more.. PHEW !!!
66% done... keeping my fingers crossed
ok, installed...now, one more problem..my touch screen's not working...???
Any idea what to do?
i installed "Prophet_PDAViet_Step1"
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
I have also tried to use ActiveSync to version 3.8 (I found this suggestion from this web site) but bad luck it can't detect my BA device at all. I have also tried to revert back to WM2003SE but still get the same problem. My system is WinXP SP2 & O2 IIs. So Please help I am in the dark right now.
Same problem here...
su2003 said:
I have upgraded from WM2003SE to WM6 (the first released from XPlode version OS 5.2.1620 build 18125.0.4.2) without any problem. Now I want to upgrade from that version to the current release, but the ActiveSync (I am using 4.5) always disconnect after MaUpgradeUT_noID has detected the previous installed OS. So I got an error message like "cannot to the device" or so. It happens everytime even I just try to upgrade the Radio rom.
Click to expand...
Click to collapse
get into boot loader mode,then try
(press record button + power button and reset at same time)
addan said:
get into boot loader mode,then try
(press record button + power button and reset at same time)
Click to expand...
Click to collapse
Have tried that already but still get the same error. I have even reformatted my PC and reinstalled WinXP and ActiveSync 4.5 just in case there are viruses or so but also get no luck.
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Did you soft (or hard) reset your BA and reboot your PC after failure? (Try clean upgrade, and in bootloader).
Yes, at this time you asked me. Nothing changed.
Did you (succesfully) establish an ActiveSync partnership before upgrading?
Yes.
Did you try unchecking Enable advance network functionality in USB to PC (under settings, connections)?
Yes. I did it.
More over, if I started BootLoader mode before execute MaUpgradeUt_noID.exe the program get struck while performs device information checking, I have to pull it out from Sync station the program then continue running but without any information (like the existing OS version etc.)
how long did you wait for the program to respond before you find that its stuck ?
Here it takes about 2 min to find the device
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
2. place it to cradle
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
4. start upgrade utility and follow the onscreen instructions
5. perform hard reset (the three options thing)
thats all
Xplode's new cube cab
deleted... off topic
how long did you wait for the program to respond before you find that its stuck ?
It was about 5 min and the program still had no responses. I then have to pull it out and the program continue running but without any information (like I had mentioned it before).
Here it takes about 2 min to find the device
Unfortunately not with mine.
Proper upgrading procedure, as it was said 10000's of times
1.put your device in bootloader mode
Yes. I did it.
2. place it to cradle
Yes. I did it.
3. kill activesync (optional - if you dont do it the upgrade utility will do it for you, but sometimes activesync stays on and fail the upgrade process)
I have tried it both with and without killing the activesync.
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
su2003 said:
4. start upgrade utility and follow the onscreen instructions
Yes, but once I started the upgrade I have noticed that the activesynce has disconnected my device.
5. perform hard reset (the three options thing)
I didn't have chance to go to this point.
thats all
I think the main problem is the activesync has disconnected my device suddenly when started the utility. I have also tried to take out anythings that using USB port like mouse, ext. DVD, printer, scanner just in case the upgrade utility may conflicts with those devices.
I think I shall try to change the PC to upgrade my device to make sure that it wasn't caused from hardware defection.
Click to expand...
Click to collapse
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
Good luck!
With regard to your last remark: you stated earlier you did a fresh reinstall of XP. Now, why would you install and connect all these peripherals if you only want to upgrade your BA rom??? All you need is a fresh WinXP and ActiveSync...
Did you really do a fresh install and follow the wiki and the tips mentioned again (and again)?
You are getting me (and probably all of us) confused.
First of all, Sorry if I make you and other confused. I have began to unsuccessfully upgrade my device since Friday. So I decided to help myself at first by try to do everything I can do by myself. I have formatted PC HDD and also reinstalled activesync because I thought the utility may conflict with other program on my PC or from Viruses. I have also tried many ways with hard reset and cold reset etc. to upgrade my device but have no luck. That was with very fresh new installed WinXP PC. Unfortunately, I have to use this computer for my job also. So that's why I have to install printer & scanner driver including MS Office, AutoCAD and other necessary program to serve my job . I have falled with upgrading but I do not want to have problem with my job. Hope you understand my essential.
Your answers to especially points 4 and 5 of xplode tips to me clearly indicate that you do not really take (enough) time to understand the procedures (or what you are doing) and want to have WM6 running asap with no effort at all...
Since I began to upgrading and everytime I have executed the utility I have always wait & wait but I just never look at the clock to see how long I have waited. Xplode has just warned me to take enough time so I started to upgrading but with clock at this time. I have already mentioned that I have successfully upgrade from WM2003SE to the WM6 (previous version) so as a user I have enough experience and know what I am doing.
Your remark "I think the main problem is the activesync has disconnected my device suddenly when started the utility" only confirms this as this is the whole point of boatloader and was furthermore indicated it would do exactly so by xplode earlier on.
This is just my opinion to let you guy see and understand the problem. That's it.
Please do take time and hence show consideration to all of us that are trying to help you in preparing yourself properly before trying to attempt any further upgrade.
I think I have already put a lot of effort about upgradind my device. I have reformatted and reinstalled all necessary programs. It took me out almost half a day to do this. And not only with my PC I have also reinstalled all programs on my device with an old OS version since I have lost them all from hard reset. Other than that I have also tried & tested upgrading the device during the time. The only word I can say that It was not funny to do all of this. It was not really a hard job but it took almost my weekend time.
Good luck!
Yes I do need it barely. Actually I have already felt a little lucky got from all of you that try help me solving the problem. Thanks.
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
April 1 said:
su2003, nice answer.
His main problem is that he does not understand that activSync will work if the device is in a normal state but when device goes to bootlogger mode, its only USB connection that will help a PC to talk to Device and not activSync.
Click to expand...
Click to collapse
Thanks for your additional.
I have also tried using different PC to upgrade the OS but got the same result.
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
I am quite sure that the screen has displayed USB but the number is 2.07 not 2.06. I am not sure about the meaning of the number, it could be the version.
I have also brought a new USB-XDA IIs cable yesterday, just in case the cardle was defected but it doesn't work also, I have got the same result.
khanem said:
you have to be sure that your BA when cradled display USB (after getting into bootloader mode) instead of serial 2.06 than run the upgrade utility
Click to expand...
Click to collapse
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Conclusion:
Bad Hardware(Flash ROM)?
Your Bootloader is toasted or had it's LAST flash of it's lifetime???
We can say that... but hopefully not for your sake.
Because as you have said you've done EVERYTHING that was posted.
and though our Senior's "inputs" didnt worked out the way it SHOULD work.
I cant say it's a waste of time to answer your questions.
But there are no more questions to ASK
and there are no more questions to ANSWER
They're all been said here.
All you have to do is PRAY HARD leave the BA rest for a day...
remove the battery...
think things out, clear your mind... sleep...
then execute Xplode's Walkthrough from Step 1 the next day.
but be sure to have the battery fully charged.
Your BA is not dead and your bootloader is not toast. The only problem you have is probably you are impatient. Go to the Wiki and follow the procedure exactly as it is written. It will work. By the way, if you kill Activesync (ie disable USB connection in activesync connection setting), put your device in bootloader mode and connect your usb cable (in that order), run the upgrade and it will work. Forget about activesync.
su2003 said:
I am quite sure that the screen shown USB 2.07 (should be differ version than your).
I have also brought a new USB-XDA IIs sync cable but getting the same result.
Click to expand...
Click to collapse
I use xda IIs and the bootloader mode shows ver 2.07, and i dont have any probs installing. I dont think the version 2.07 has got something to do with your problem.
You said that you tried other pc and it doesnt work, and it worked before when you upgraded previously. I think you know enuf about upgrading if you have done it before....
did you have problem with sync connection before? I was just thinking maybe there is something wrong with your BA....like actual hardware problem with the cable connection??
what about firewall? would it affect it - I doubt it cause its not in sync mode.... but at this stage, maybe just try all possibilities to try to get it working.
Good luck
Mhm. I'm not sure I've really followed all the intricacies of this case ... But whatever, here's my two cents for a safe upgrading procecedure:
1) use a cradle, not a USB cable, and make sure the cradle's
power supply is plugged into a wall outlet. It also helps to make
sure the cradle is plugged directly into the PC, not via any kind of
USB hub. No other devices should be connected to that same USB
channel. I suppose temporarily disconnecting other (unneeded) USB
devices from the computer can't hurt, either.
2) I guess "kill ActiveSync" can mean various things ...
however, here's the best way to do it I think: as sofene mentioned,
disable USB connections (what the hell - disable ALL connections) in
ActiveSync settings. Then reboot the PC. No need to look for ActiveSync
processes and kill them manually -- disabling the connections will take
care of that. Rebooting ensures that ActiveSync's driver code is really
unloaded.
3) remove SD card and, for good measure, SIM card from the BA.
4) perhaps soft (or even hard) reset your device
5) put device in Bootloader mode
6) insert device in cradle, start upgrade utility, off you go ...
By the way, ActiveSync has got nothing to do with the ROM upgrade utility, and it should therefore not have been necessary to re-install ActiveSync, etc. You just have to make sure it does not get in the way of the upgrade process. As far as I understand the process, the ROM upgrade should work equally well on a PC that does not even have ActiveSync installed.
Gone through the various help threads on rebooting, resetting etc.. Battery is charged, m/card and sim have been removed..
Phone is at the boot loader stage - reads Upgrade ROM code error - have the USB plugged in and can see the USB writing on the white part of the red,green,blue,white screen but pc refuses to make a connection.. keeps saying activsync not connected or busy..
Have tried rebooting the phone and also the pc, changed cables, changed USB port.. no joy..
Any suggestions appreciated..
not sure what you want...but you have certainly described the situation really well.
i understand that your device is in the bootloader (thats the multi-color screen). i understand that "USB" is written at the bottom of the bootloader screen. i understand that you have removed all the cards.
what i don't understand is what you want help with? why are you trying to establish an activesync connection? activesync will obviously NOT connect if you are in the bootloader because the bootloader isn't the same as windows. windows mobile must be running if you want a full activesync connection.
so what exactly are you looking for? do you want to flash a ROM or radio ROM or some such? are you simply trying to "hard reset" your device? details please!
yea, dont be confused by posts that say 'when connected to active sync, blahblahblah', they dont really mean activesync the program, they simply mean a usb connection. The fact that it says USB on the white part means you can now run your rom flash,.
ok.. what I am trying to do is re-flash the ROM.. I had a flashed ROM on there and I was just going to upgrade it to the latest one (Laurentius26 GoldEdition V3.4 Stock/Spike™ WWE 23568) and about 20% of the way through it froze and then I get a recovery screen come up.. followed the instructions and started to flash again and the same thing happened.
In both cases it seems as if the USB connection was dropped even though there was nothing else happing on the pc at the time.. now when I try to re-flash, no US connection is being established.
Well I left everything disconnected last night and tried again this morning. We have got a connection now but the re-flash has failed again so I shall just go back to the old ROM.. thanks for you all's input.
probably a bad ROM download. I would try to download again and if that doesn't fix it, let the ROM cooker know that he probably has a bad upload of the ROM.