I upgraded my Siemens SX56 to PPC2003. Everthing is great, however, even at high volume I can hardly hear the ringer when some one calls. I have the system volume at high and the phone volume at high.
Has anyone else had this problem?
Eric
I have the SX56 also and don't have that problem. Is the ringer you are using a standard one or something you loaded onto you device? Also, since you are with ATT, with this new rom do you get the little "G" in the title bar and phone section showing you are able to connect to GPRS? You can check by clicking on the signal meter in the title bar. Thanks.
Related
I recently upgraded to WIN2003 ROM 4.0.0.10. It works great, except few things, my signal is weak in places it wasn't before. Has anyone experencing this. Can I revert back to the orginal radio stack 6.18?
Also, My phone volume seems lower? Any ideas?
Thanks,
BrettX
I have experienced just the opposite. My signal strength and sound quality has improved with 6.24.
You can adjust the call volume by pressing the volume button during an active call.
David
So, I'm experiencing what everybody else is with this ROM. That initial volume level starts out soft and gradually increases to the max that I have it set to. Some have stated they like this and that's fine. But, I HATE it :evil: . I can never hear my phone ring anymore if it's in my pocket. Has anybody found a possible registry key or setting somewhere to turn this off?
And if any AT&T folks are listening.. I'd like a setting in the volume area to turn this off or on.
Phone Profile
Have you check under phone profiles... Ascending Ring change to Standard Ring
Dustoff
I don't have a phone profile, or i should say i don't see any where for that option. In the phone settings area the Ring Type is set for Ring. There is an option for "Increasing Ring" but that's even worse than it is already. I don't think this is what I'm looking for.
Since the WM2003 upgrade on my SX56, 've noticed issues with the speakerphone volume. I can barely hear it in fact. Any thoughts on this one?
Fiddled around with the volume setting, moved it up and down, and the now the volume issue seems resolved. Can't say for sure if that's what resolved it, but it's fine now.
I'm experiencing the same problem with the AT&T rom.. I'm going to take a look around in the registry later on... before I go installing any apps
Well I have taken a look @ the processes running and can't see anything obvious that would be doing the volume thing..
So I have had a poke about in the registry and have found a section with sound profiles and it has an attenuation property, I have tried adjusting this, and deleting it but still no good
Also there is an entry in the registry called Hack and mentioned Vol in the string... but it didn't make any difference when I deleted that either :roll:
If anyone thats a bit more acomplished than myself with the PPC Phone could take a look and find a solution to this, i'm sure many users would appreciated it
Has anyone figured out how to make the volume level constant yet?
Any solutions to get the volume working well on A.30.09 ENG yet?
Nope. I just put my phone volume on next to the top setting and the system volume two levels below it. Works fine then. As long as the system volume is two levels below it will not graduate the sound.
valheru said:
Nope. I just put my phone volume on next to the top setting and the system volume two levels below it. Works fine then. As long as the system volume is two levels below it will not graduate the sound.
Click to expand...
Click to collapse
Another thing try ur Reminder set an Alarm you'll notice that you cannot change the Alarm1 ringtone thus the sound stays low ..I tried many things in the registry and no luck as well I wish would some1 help us to resolve this Issue, but!! I made contacts with att's support ,I told them about this problem thus I'm not the only one who's experiencing this, lots of ppl sees this ennoying , I hope they would help here...
I just finished installing the new SX-56 WM03 ROM on my O2 XDA I unit. Having tried the new ROM for hours, I find it quite satisfactory and stable compared to its predecessors but there seems to be one set back though, the volume!!! It's quite noticeable that the volume had been tweaked down to about 30%, and they just made it more impossible for XDA users to hear whether there's an incoming call or message. Is there a way around this? I really hate to switch back to my old ROM just because of this!!!
Expert Advice Needed!!!
Your help will be greatly appreciated...
I have same problem... I think it's bug. If I set the system volume high, then the phone ring silent, if I set the system volume low, then the phone ring loud...
If you set the phone to 80%, means to klick under max. Than you can use 100% phone ring and volume.
Yup, that's exactly the case! you set the volume at 80% and it gives a louder voulme than having it set on 100%. I guess there is someone here who knows how to get around this problem...
So does anyone really have a clear solution to this problem? like a program I guess?
ohenry774 said:
So does anyone really have a clear solution to this problem? like a program I guess?
Click to expand...
Click to collapse
The solution: switch to ROM T-Mobile 2003 v4.01.16 ENG, and it's look like working fine without AT&T sound level bug.
I downloaded directly from T-Mobile, but I think You can find it at ftp://xda-developers.com
Hi all,
Before I say anything, I am using the 2.17 ROM. When talking to people I cannot adjust the call volume. Its always set to max no matter what I do with the volume slider or the volume icon on screen. It's so loud that the speaker gets distorted. I am afraid if it stays this way either my speaker will blow or I'll go deaf!
Any suggestions out there as to why this is?
Thanks.
What device do you have? I gather thats a qtek rom. But we can help you more if we know if its a cingular/vario/imate etc... You may need to try the native rom to see if its a software or hardware problem.
Are you sure you're adjusting the volume while you are talking? In-call volume can only be adjusted in the middle of a call. (This may seem obvious but I only realised this recently )
I wish I had your problem...
Mine is the exact opposite!
My in-call slider does nothing. Sure, it moves up and down, (and yes, during a call) but it does not change the volume @ all!
Mine is stuck on 'almost inaudible' so i can barely hear anyone.
Tried 2.24 cooked T-mobile ROM, (that's when it started) and mr clean's rom hoping that would fix it...
No luck.
Anyone?
I have the same problem with my HTC 8125 by cingular with WM 6.1 (Newbie's ROM IPL 2.25 - SPL 2.25 - GSM 02.69.11).
Please, if you know how to help out, or have had this or a similar problem let me know what to do.
My Wizard is acting very weird. Whenever the phone rings the phone volume automatically goes to the highest level. I would change it to a low volume but once another call comes in it goes back up by itself. Also, once in a while, there's no sound from any speaker even though the volume bar shows there's sound. Adjusting the volume bar doesn't bring the sound back--it's muted. I have to reset the phone to fix the problem.
FYI: I'm using T-MO custom ROM 2.17.
Has this happened to anyone else? Any ideas? Thanks