[Q] Flashing rom for htc touch HD - Touch HD General

hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic ​

basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.

Chef_Tony said:
basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.
Click to expand...
Click to collapse
thnx 4 help really usefull and easy,i apperciate it
thnx again

@ blackspyker
did you successfully flash the hspl and a new rom?
(just seeing if this thread is solved or not)
Rn

just like me dear, please help us. but mine is English version
just like me dear, please help us. but mine is English version
blackspyker said:
hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic ​
Click to expand...
Click to collapse

download this, extract all the files, take micro SD out of device, connect device to active sync and then run HardSPLWrapper_Blackstone.exe on your pc, it will now start to flash a new SPL, when complete confirm you got it installed, go into bootloader mode (tricolour screen! {hold volume down and press the reset button under the back cover}) now verify the screen shows 1.56.OliNex, which is the new Hard-SPL version.
when complete you will be able to flash any rom to your touch hd/blackstone
note: if you do not flash a new rom you will have graphical issues with the current rom, however this gets fixed as soon as you flash a new rom
if you have any trouble, click me and go to the first post
good luck

Related

Please help!

im getting a touch hd from taiwan. and i just read that it comes in chinese only
is there any rom to make it english? or change the os language to english
and what is the country code for it?
if there isnt. will i have to use hard spl?
and i read the instructions for it but im kinda lost
please help
Thanks in advance
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
EpiphanyNL said:
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
Click to expand...
Click to collapse
i checked "http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe"
and im not sure which one to download
im not really sure which is the country code for taiwan. any ideas?
there are ways to flash without using hard spl?
can you please tell me how?
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
EpiphanyNL said:
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
Click to expand...
Click to collapse
i read that i need to know so i know which rom to download?
i think. i read it here " http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1"
so im going crazy looking for a rom that i could use.
do you know where i can download one so i can make my language WWE instead of chinese.?
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
EpiphanyNL said:
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
Click to expand...
Click to collapse
thanks but one question?
which is the easiest way to flash a rom?
using Hard SPL, Soft SPL, or USPL?
im really lost on that..
and which one should i use?
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
EpiphanyNL said:
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
Click to expand...
Click to collapse
oh really?
hardspl is only for blac100 right?
but i read that now they have like blac120?
and im not sure which one im gunna be getting in the box.
oh. when i change the os language. do i have to download one with the same country code?
i read in another place that if you dont have the same. then. it wont work?
or with hardspl and uspl i dont need to have the same country code
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
kevin6192 said:
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
Click to expand...
Click to collapse
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
alvinswim said:
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
Click to expand...
Click to collapse
Fallen Spartan said:
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
Click to expand...
Click to collapse
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
kevin6192 said:
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
Click to expand...
Click to collapse
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
ionrage said:
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
Click to expand...
Click to collapse
oh really?
when it says
"Execute blac_uspl.exe;" do i just find the file ont he computer and double click it? or do i have to like install it using the phone?
and " If everything goes well, your device will restart and SPL version label should read "1.14.USPL" indicating that USPL was loaded successfully."
once that is done then... am i done?
this next part is when i want to flash a rom right?
("You can then start RUU update to flash RUU_signed.nbh. Once RUU update is completed, device will restart using regular flashed SPL.
If you want to flash from SD card instead, make sure your SD card is not inserted when you enter the bootloader originally.
SPL will try to install it and would fail if blacimg.nbh is not signed by HTC. Insert the card after "USB" label comes up in SPL but before running USPL.
You can run "blac_uspl.exe ?" to get command line parameter help. Only 1 parameter is accepted and that is the name of an SPL file you want to load. You can load an MFG SPL or HSPL. USPL automatically takes care of allowing unsigned/cooked ROM flashing with any SPL you use.")
man. i dont have XP
thers no way on vista?
thanks for the inconvenience.
Fallen Spartan said:
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Click to expand...
Click to collapse
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
kevin6192 said:
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
Click to expand...
Click to collapse
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Fallen Spartan said:
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Click to expand...
Click to collapse
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
kevin6192 said:
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
Click to expand...
Click to collapse
Yes you need to extract it from zip as it will not run from within zip folder
Personally I ran it just from the desktop, i.e. I put HardSPLWrapper_Blackstone.exe on my desktop
when you have your phone connected and in bootloader mode at the bottom on the screen it should say 'usb'.
then launch HardSPLWrapper_Blackstone.exe, follow steps, then your done.
As I said put phone back into bootloader mode afterwards and verify the screen shows 1.14.OliNex, which is the Hard-SPL version.

[GUIDE] Step by step instruction to install/flash a custom rom.

Hello all,
There are many new users who want to install/upgrade to a custom rom but totally don't know from where they should start. So, they ask the same question again and again in irrelevant threads. Here is a very short guide which will help you to install/upgrade to a custom rom and will hopefully prevent newbie's from asking the same question.
@All New users: There is no problem in asking question and everybody is ready to help you but many ppl just don't go through the pages even tho the question has been answered several times in a single thread.
Things to be known:-
1. Flashing The term flashing means installing or upgrading. When we say Flashing a rom that simple means we are installing the rom. But sometimes you would have seen in forums ppl saying flash Hard spl or so. Here too flashing simply means installing.
2. Basic information On powering up your phone the basic information displayed on the screen are: ONBL version, SPL version, GSM or Radio version and OS version.
For flashing a custom rom we only need to know about SPL for now.
3. SPL Here is the description of SPL by krazy_about_technology,
SPL or Second Program Loader is a part of your phone's firmware. Its responsible for both loading of operating system and it is also used by operating system for some low level tasks. By Default, HTC and Other Manufacturers too, design it in such a way that it does not allows custom ROMs to be flashed in the phone. It does no by checking for the Digital Signature of HTC on roms. So it need to be patched in order to flash custom ROMs made by chefs in this forum.
4. H-SPL As you can see in the above description that SPL are designed in such a way that it doesn't allow you to flash custom roms. So we need a H-SPL ( Hard SPL). When we flash a HSPL it simply patches the current SPL or in other words it unlocks the device for flashing custom roms.
The flashing process
1. Flashing HSPL First flash HSPL, head over to this thread ( here ) for all the instructions and downloads of HSPL.
2. ROM Now after flashing HSPL choose a custom rom. Almost all the custom roms are compressed commonly with winrar or 7zip.
So, if you dont have winrar or 7zip to uncompress the package get any one of them. My suggestion is get 7zip from here.
After uncompressing the custom rom package there are two cases,
Case 1: There is a single *.nbh file, generally the rom file is named as RUU_signed.nbh ( but remember it may be of any other name too, just it will be of *.nbh format ). In this case you need some additional tools to flash this file into ur device.
How to flash the nbh file (this only guides you to flash nbh not unlocking ur device (hspl)​
Here is a short method.
1. Download this Installation package (295 kb). here
2. Extract the above downloaded package anywhere on pc (say desktop)
3. Copy the downloaded nbh to the extracted folder. (Here the extracted folder name is Installation package)
4. Double click on ROMUpdateUtility.exe
5. Follow the onscreen instructions.
Thats it!
Case 2: After uncompressing the custom rom package you will see there are additional files with the rom file. These additional files are nothing but the tools required to flash the rom into your device. So in this case you don't need any additional files and you can directly for for flashing.
Flashing the rom:
For XP
1. Download and install Microsoft Activesync 4.5 (the latest) if you don't have it in your pc. It can be downloaded from here.
2. Connect your Device with PC via USB cable. As soon as you connect you would see a pop up window on your device. Probably there will be three options, you have to select the option which is Activesync.
Now you should see in your PC Activesync connected, if it didn't sync open Activesync go to connection setting and select the port through which your device is connected. Now re plug-in your device.
3. Run the ROMUpdateUtility.exe remember the flashing tool should be in a folder where the rom file is also present. Follow the on-screen instructions. Thats it.
For vista/windows 7
1. Download and install Microsoft Device centre from here.
2. Connect your Device with PC via USB cable. As soon as you connect you would see a pop up window on your device. Probably there will be three options, you have to select the option which is Activesync.
Now you should see in your PC Device center is connected, if it didn't sync open Device center go to connection setting and select the port through which your device is connected. Now re plug-in your device.
3. Run the ROMUpdateUtility.exe remember the flashing tool should be in a folder where the rom file is also present. Follow the on-screen instructions. Thats it.
Essential thing to be known:-
1. Bootloader mode Knowing how to enter into Bootloader mode is one of the most essential thing to be known for a opal user (windows mobile users).
How to enter?
There are two way to enter into bootloader mode.
1. If you device is on, open your device's back cover. Press the soft reset button ( red button ) using stylus. As soon as you press it, immediately press the volume down button and keep holding it until you see a tri-color screen on your device's screen.
2. If your device is off, press the power button as soon as the device vibrates immediately press volume down button and keep holding it until you see a tri-color screen on your device's screen.
Uses?
If you flashed a damaged rom, you would be no longer able to use your device. In that case enter into bootloader mode. And flash a different rom.
Thanks
Explain the excellent and easy to understand, good work Thank you
Iam glad that you liked it. I hope now ppl will refer this thread and not rom threads. Ppl can ask all the question that they ask on other threads here.
Nice Guide
You've done a great job with this guide. Thanks. I've already referenced it on another post.
i have hard spl my device...i've instales the rom from this: http://forum.xda-developers.com/showthread.php?t=680164
after that i;ve tried to unlock my phone...is from austria t-mobile...
when i've tried to use some programs to unlock the phone, the progress bar went to 7% and the a windows pups and said that there is a 260 error...
the i instaled again the 6.1 rom froms here: http://ptxserver.net/blog/?page_id=37
the i've tried again to unlock the phone but same error...
but when i started to put the first rom on mi device...opal v 6.5..i have the same problem...can someone explain how to unlock the phone and to have the first rom on my device(opal version 6.5 d25)...pls...
Ruch0 your question is not at all clear, if you want someone to help you then please make it little more clear.
Is your phone sim locked, if so then it is always said not to flash a custom rom.
According to ur question u say u have done hspl and installed a rom then trying to unlock the rom. Here by unlocking do you mean sim unlocking?
to make a better point i want to get rid off the 260 error...because i have found a lots of programs that will sim unlock the phone...
know i am trying to use this:
1. download hardspl v7 from the first post.
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done.
but i cant start the sspl-herm.exe from my mobile...
LOL, that really made be to laugh. First of all are you sure that you have a HTC Touch Viva (opal) because from your description it is clear that you are using herms and having some probs. Well, my friend this section is ONLY for the device called HTC Touch Viva (opal). So asking here is a total wastage of time.
You should immediately head over to herms section and ask the ppl over there. Visit here.
do i need to install h-spl on my windows seven before flashing or not????
sanchitgrover said:
do i need to install h-spl on my windows seven before flashing or not????
Click to expand...
Click to collapse
After you have connected your device to pc and it is showing connected in Device centre (Windows 7), follow the below step
1. Flashing HSPL First flash HSPL, head over to this thread ( here ) for all the instructions and downloads of HSPL.
Click to expand...
Click to collapse
yes yes yes work fine and was very easy to do all the job 10q
Error
Hi, friends
maybe not to post it, but,
so want to flash my device, but don't, when I start de hspl flash not appear de bar, (0%), then show [202] connection error, maybe the hspl? or my device not supported? original spl 1.52.000 / F256?
thank you, if some one can help me
caioofaria said:
hey, jagan2, ok,
but, I'm working tomorrow, and the firewall, will not able to receive a remote access, but to explain, i connected my device, then I tried to run opa_hspl_v2, then it go so the bar of progresse, but in few seconds appears the error [202] connection error, I've tried in windows vista, xp, seven, all with net.framework working, maybe the my spl version? my is 1.52.0000 and ONbl 1.52.0000, gsm 1.52.0000,
I'm waiting to use your Evo 2.5A, really amazing with the features and look
Click to expand...
Click to collapse
The main thing you have to check is whether your phone is synced with ur PC via activesync/windows mobile device centre. If you are sure that it is synced then also not working then there might be some other problem.
About remote access don't worry there is a software called Team viewer it will bypass all firewalls.
Yeah, Jagan sorry, I know the team viewer, tomorrow we can use this,
thank you for ur help.
Jagan
Can u help me today?
Need Help
Hi Jagan
I have HTC Touch Viva purchased recently in India.
Software : Win Mobile 6.1 Professional Build : 19971.1.2.6
ROM Version : 1.35.720.2 WWE
Radio Version : 03.37.90
Protocol Version : 4.1.13.74
I tried to update its OS to Win Mobile 6.5 first time.
I followed your instruction in Post 1. But I am unable to do that.
First I tried HSPL 2, but it didn't work. I got 202 error.
I downloaded the ROM from the following Link.
http://forum.xda-developers.com/showthread.php?t=629257
ROM update also failed.
While updating, it showed the message like
Current ROM Version 1.35.xx...
New ROM Version : 1.27.xx...
To update the OS to 6.5, I need to do any thing else? Where I am going wrong? Plz help.
ivk: caioofaria has too similar problems that is error 202, its like in some pc its not coming and in some its coming. I will check that out again today in caioofaria's pc.
I will post result of my testing today, if anyone has a suggestion post it here.
For now iam assuming that ivk and caioofaria is not able to flash hspl because of there new default os. I will try to get a solution for this,
But if anyone has suggestion be sure to post it here.
Need Help - Update
Hi Jagan,
Little bit improvement in my problem.
The HSPL completed. Now the spl version : 1.26.0.0
Again when I try to update the ROM, getting Update Error 270.
Tried on different laptops(win 7). But getting the same problem.
Thanks.
No the spl version should be something like this 2.00 cmonex
That means you have done hspl yet. Actually i think i got the prob of the error, when you u try to do hspl and ur screen goes tri color then your pc will or i should say must install a driver it will be something like "Pocket pc syn" if its not doing then hspl will not get flashed. Just one again try to do hspl in windows 7 then when you are in tri color screen see in ur notification area below that some driver is getting installed.

How to full format HTC HD without task29????

Hi guys!!
Is there any way to full format htc hd device without using task29?
Two weeks ago I flashed ROM via SD card, and since then ActiveSync doesn't work and I can't establish connection with my HTC HD and computer.
Now I can flash ROM only through an SD card. When I get into Bootloader mode does not recognize USB, but remains on the Serial....
Hard reset does not help because it only erase contacts, emails and other crap. I need something to wipe the device.
Any possible ideas??!!! Please....
didnt you by any chance disable USB connection in your activesync settings?
check that, maybe that prevents you from connecting...
if that's not the case, try updating your drivers...
if that fails, then AFAIK Task29 is the only way to format your device...
I tried to change everything in USB2PC and it didn't work. I took the device to servis and the repairman told me that he doesn't know what is the problem. He thought that maybe some port is broken or something like that and will replace it but none of that. Everything in device works fine. That he told me.
I think I made a mistake. When I flashed ROM via SD it all went great but in the end (after message: update complete 100%) I didn't make a soft reset. Instead I pulled the battery out to re-started device. Could it be the reason?!?!
So this AFAIK task29... what does it mean?!?!
how can i do this?! can you be more specific, some steps or something... please
and thank you for reply
oh yes, and i forgot to mention, when I connect device to PC it start to chargining battery normaly so can't be problem with USB cable as well
be sure to check your activesync or Windows Mobile Device Center settings...click the settings for mobile device or similiar and make sure Allow USB connection is checked...
AFAIK means "as far as I know"..
Task29 is a process with which you can completely erase your system partition...this little process solves a lots of issues..
Let me help you out.
First of all, connect your phone via USB to computer in bootloader.
Run USPL
Download the attached package - it is Task29 with Blackstone Radio 1.17
Extract archives and run Task29.exe
Follow the instructions - it is the same as flashing process
After task29 your phone will reboot but wont boot because there is no OS.
Take out battery and get into bootloader again.
Connect to PC via USB, run USPL and flash your favorite ROM.
I recommend Topix or Duttys.
Let me know if this worked out for you.
PS: Sorry that there are so many archives but I could not get it to smaller size
PS: Also do not forget to backup the data!!! this erases completely everything...
Sopis said:
be sure to check your activesync or Windows Mobile Device Center settings...click the settings for mobile device or similiar and make sure Allow USB connection is checked...
AFAIK means "as far as I know"..
Task29 is a process with which you can completely erase your system partition...this little process solves a lots of issues..
Let me help you out.
First of all, connect your phone via USB to computer in bootloader.
Run USPL
Download the attached package - it is Task29 with Blackstone Radio 1.17
Extract archives and run Task29.exe
Follow the instructions - it is the same as flashing process
After task29 your phone will reboot but wont boot because there is no OS.
Take out battery and get into bootloader again.
Connect to PC via USB, run USPL and flash your favorite ROM.
I recommend Topix or Duttys.
Let me know if this worked out for you.
PS: Sorry that there are so many archives but I could not get it to smaller size
PS: Also do not forget to backup the data!!! this erases completely everything...
Click to expand...
Click to collapse
OR You can try to flash a Stock ROM from SD ... probably works like Task29
Try using MTTY. Check firs for bad blocks. There is a command that will format the device.
Check Hermes WIKI, there are a lot of explanations about MTTY and how to use it. Also there are explanations about commands. Just be careful, you can destroy your device.
As far as I know mtty works on all win devices.
Cheers
I can't use anything...
The device can't recognize USB when I connect usb cable with it (it stays on SERIAL in bootloader), so I can't use task29, MTTY or similar applications or even flash new rom with RUU.
I think there is a malfunction on motherboard.
I tried to flash a stock rom with stock SPL 1.14 and this what happened:
It stays in bootloader mode with this error report
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again (in green field)
I tried to flash stock rom again and I get error code 00028002.
Stock ROM can't be flashed through SD card so now I can't use my guarantee......
so what do you do next to fix ..sorry my ingles
sollution!!
delete your previous connections in activesync, and then you need to HARDSPL your device, and after that you will be able to install romms from your sd card
there is a Thread for Task 29 for the Blackstone, please refer to it to minimize
redundancy.
jigners said:
there is a Thread for Task 29 for the Blackstone, please refer to it to minimize
redundancy.
Click to expand...
Click to collapse
As per above post, please use existing Task29 thread
Thread closed

[HELP] HTC HD2 cant boot after hard reset or hard reset failed

hi guys..
please help me .. i flash my HTC HD2 with a MAGDLR111 and after it doesnt continue to boot and only stock in boot image. i try to use Hard Reset (holding down the up and down botton and tapping the power button), it response very quick but it says the "restore completed and press up botton to reboot" and so i did but still, it still stock up in boot image forever.. please help me, what should i do..thanks
Possibly a radio problem. Boot pressing volume down button to get into bootloader and flash a radio WITHOUT .51. in its name....
Sent from my Nexus One using XDA App
thanks, already did... and it works.. )))
hey i have that same problem now can you help me get a radio so i can download it or can even help me through the steps to get back my phone to normal plzzz.? thank you
Any new user most definitely has a lot of questions...
Here is a thread you should carefully check - it explains some basic stuff, and it offers links to many other specific threads, incl. Radio ROM.
To return to "normal" ROM, please just check the standard flashing process. You can flash via USB or SD card, whatever ROM you like, stock or custom.
Hey man thanks for all that but i really don't want just any rom, i wanna know if anyone can get me the rom that comes with the phone for windows mobile 6.5, you know with the orange load screen etc, i really dummy in this thing and i should not of even played fast to go try flashing my HTC HD2 with a MAGDLR111.
so i've tried various roms and everyone of them was going great unitl step 2 in the upgrade process, it kept saying error filr open, check update rom utility. where do i go from here?
It is quite difficult to help if there is so little basic information available.
The error you mention can have a simple reason. Usually, the ROM image file name is simply not correct.
To flash via USB:
There are 2 options:
First, you can take an original RUU of your network operator (in case you have a branded phone) or HTC, put the phone into boot loader mode (see below), start the RUU.exe on your PC.
Second, you can extract the original RUU.exe with WinRar or a similar program, take the .nbh file and rename it to leoimg.nbh.
Once you take an image of the ROM, you have to put it into the very same folder where your ROM update software is (LeoCustomRUU, SSPL, whatever). One more time, please check the suffix, it should be .nbh, as in "leoimg.nbh".
Keep in mind: Do start the RUU software as "Admin" - whichever you choose.
Instead of the original ROM, you can flash custom ROMs, too - since your device must have HSPL installed when you used WP7 or Android before.
If you´ve got issues (because of Win 7 on your PC or such), please try to put your device into bootloader mode before connectint it to the PC (turn off the device, push vol. down and power at the same time, the multi color bootscreen should appear, only now connect it to the PC).
To flash via SD card:
Re-format your SD card FAT32. Don´t put anything else on it. Copy the ROM image file with the exact naming as above on the SD card.
To start the flash process, do the same as above, go into bootloader mode, the flash process will start - just follow the on-screen instructions.
i have this same problem only it happened without me flashing anything or something like that. i dont have custom rom or hspl. everything is stock. what should i do?
bump ^^
The message you have entered is too short. Please lengthen your message to at least 10 characters.

Reflashing stock att rom

I have an HTC Surround that I cant get to boot past htc logo and if i try to hard rest it goes to spl screen. Where can i get the software to reflash it. I also have another microsd that i can change out if that is bad
still working on
So I replaced the mirco sd and tried to do the restore using the power and volume buttons and still would not get it to try and boot more then a few secs and stop at the htc screen. I also flashed the stock att rom that I got off xda but still no luck. My last chance is trying a new battery today are there any more suggestions
My surround did the same thing recently. It's a problem surrounds have. Unfortunately you have tried the 3 most common solutions.
1: reflash with stock rom
2: Change out sd card
3: hard reset
The only way I know of to get a working one after you have tried those 3 things is hope it's under warranty. :-/
jackkaiserwork said:
So I replaced the mirco sd and tried to do the restore using the power and volume buttons and still would not get it to try and boot more then a few secs and stop at the htc screen. I also flashed the stock att rom that I got off xda but still no luck. My last chance is trying a new battery today are there any more suggestions
Click to expand...
Click to collapse
Where did you get that stock at&t rom? I've been all through the developer section and all I see are telus and cingular roms. I've got a phone from the shop that's stuck on the htc logo and replacing the sd card hasn't fixed it. I tried to flash a telus rom because hey what the hell do I have to lose but RUU wasn't able to establish an ActiveSync connection on the htc logo screen looping repeatedly. Is there a way to force it into a sort of download mode from the htc logo to do the flashing from?
AT&T Surround ROMS
v1nsai said:
Where did you get that stock at&t rom? I've been all through the developer section and all I see are telus and cingular roms. I've got a phone from the shop that's stuck on the htc logo and replacing the sd card hasn't fixed it. I tried to flash a telus rom because hey what the hell do I have to lose but RUU wasn't able to establish an ActiveSync connection on the htc logo screen looping repeatedly. Is there a way to force it into a sort of download mode from the htc logo to do the flashing from?
Click to expand...
Click to collapse
Cingular is AT&T. I have flashed both of these ROMS to my AT&T Surround. Both work perfectly.
Pre nodo : http://forum.xda-developers.com/showthread.php?t=860842
Nodo : http://forum.xda-developers.com/showthread.php?t=1051579
Is there one for mango?
thanks
Thank you very much
bmamo said:
Is there one for mango?
thanks
Click to expand...
Click to collapse
depending on the spl version of your phone you can flash the cotulla rspl/hspl then flash the DFT rom, you will get mango full unlocked
rob243 said:
depending on the spl version of your phone you can flash the cotulla rspl/hspl then flash the DFT rom, you will get mango full unlocked
Click to expand...
Click to collapse
full unlocked as in developer or simlock unlocked?
thanks
Bernard
developer unlock sorry you will be able to sideload to your hearts content even install .xap directly from the browser on the device.
great, thanks!
I'm a bit new to windows phone but I learn quickly usually. could you help me a little bit more by telling me what exactly cotulla rspl/hspl, and DFT rom are? Is there a guide anywhere i could follow?
thanks again
---------- Post added at 02:33 AM ---------- Previous post was at 02:22 AM ----------
i'm guessing this should work:
C. Windows Phone 7 ROM Flashing Instructions
1. Unzip your downloaded *.zip file in a separate folder
2. Press and hold power-on/off button to power-off the phone
3. Press and hold volume-down button and then press power-on/off button to enter bootloader mode
4. When your phone enters the tricolor screen bootloader mode, release volume-down button
5. Connect your phone to your windows 7/vista/xp pc/laptop with a usb cable
6. Verify that your phone will be identified and relevant drivers will be installed by windows os of your pc/laptop
7. After completion of (6.) above, check the usb message connection on your phone screen
8. To flash the new ROM go to your pc/laptop folder of (1.) above
9. Double click on the ROMUpdateUtility.exe file and strictly follow the instructions on your pc/laptop screen
Do You still need help about this?
Basically you need to download DFT_RSPL_WP7FG2_LAUNCH from this forum, this will allow you to flash a custom rom. The ROM installed at the phone must be a NODO one because mango roms updates the loader and are not compatible.
For apply it you must put the phone on loader. Connect the phone to the usb, turn it off, turn it on but holding volume down key.
Once there you will see the 3 color screen and will say USB run the DFT_RSPL_WP7FG2_LAUNCH and follow the steps.
The phone will restart and showing again the 3 color screen but with HSPL now you can install DFT ROM. DFT ROM is basically a custom Windows Phone with the option to sideload apps you just run ROMUpdateUtility.exe from the DFT ROM downloaded and it will upgrade your OS to DFT Version.
Now what? SPL too high!
My brothers HTC surround has crashed, and fails to load the OS. i can get to the bootloader, but it's
spl-4.2.2250.1 (129185) MNG
i've got HSPL and RSPL, but they say DON'T TRY IF NOT 1.X SPL OR IF IT SAYS MNG. his says both. he was running mango, and i'm just trying to reinstall a stock rom. I'm wondering what advice any of you might have. I've reinstalled roms on Samsung devices, but not on an HTC, so i'm not sure what all this is about, or what the consequences are of proceeding. any help would be great.
Thanks dudes.
bump?
please?
Is it 1/2 bricked?
If you connect the device to a PC does it go to USB mode? At teh red blue green screen does it say USB at the bottom?
USB
It does display USB. If i leave it on for like an hour, eventually, i just discovered, windows DOES load, and it says "your memory is corrupt" it does connect to the computer, and it is detected by my pc, and it does display USB. I'm going to try to put in a new SD card, but i'm wondering once i do that, will i be able to flash the retail rom to it, with that spl.
thanks!
Check this thread http://forum.xda-developers.com/showthread.php?t=1597837.I believe you will have to downgrade your bootloader. I haven't tried this yet myself, I hope it helps you out.
need custom unlocked rom for my htc surround at&t
Hi.. Plz help I have HTC surround at&t unlocked device and I need to fully unlock
It so dat I can install apps from web without going to wp7 market.
And I want to flash it with custom rom..

Categories

Resources