Hello everyone can you tell me what kind of processor my x96 mini android tv card has? I probably blocked everything because the card remained on the fixed blue led.
i can't connect it to the pc in any way.
Could you give me some suggestions?
Thanks
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
thank you
it should be amlogic ,you can remove the heat sink and check the SOC ,
I got the datasheet of the processor sec 643 eprom I am attaching the photo and the datasheet from which you can see that by connecting the K5 pin with GND you perform the hard reset. I tried and luckily it worked.
Download this pdf file from google: KLMAG1JENB-B041-Samsung.pdf
Thank you
tonycell said:
I got the datasheet of the processor sec 643 eprom I am attaching the photo and the datasheet from which you can see that by connecting the K5 pin with GND you perform the hard reset. I tried and luckily it worked.
Download this pdf file from google: KLMAG1JENB-B041-Samsung.pdf
View attachment 5734865
Thank you
Click to expand...
Click to collapse
Hi!
please could you say me , wich is K5 pin?
An how you make a reset? shotcut k5 and gnd conected at the power or a usb of pc?
sorry for my english!
I was download the pdf but I don't undestand nothing :-( I can't find nothing about k5 and gnd.
thanks in advance!
Quim
Related
HI,
can any one tell me which which lpt pin setting 100% work for gene Jtag Method. In these picture there is small difference please look on 14 no. pin in lpt for which picture will work for me (A) which is connected to 14. and 18-25 and in (B) picture wire is connect to outer body of lpt port..... WHICH IS CORRECT tell me.
Here Is link
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
View attachment 278665
i think picture B is correct.
or u can try both .
Picture of lpt for GENE100 JTAG
Hi,
here i am attaching some more picture..... please answer me which one will working. if any one have to successfully done the JTAG method please tell me which one is correct lpt pin point....
find file in attachment......
i cant find difference between 2 diagrams
Restore my gene
hay all,
i restore my gene with my own effort's and file of gene_jtag_restore file,,,,,,
i will build a guide for it later.....
bye...
gurusinghbrar said:
hay all,
i restore my gene with my own effort's and file of gene_jtag_restore file,,,,,,
i will build a guide for it later.....
bye...
Click to expand...
Click to collapse
hey man congratulations !!!!!!!!
plz build a new guide for restore .it will help everyone !!!!
Hi all,
I have an Arabic Iptv box which uses an A20 dual Allwinners chipset, picture of the box
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The applications kept closing automatically so i thought if i'd update it then the problem would be fixed, however, once updated the box starts up with a red rectangle as you can see in the picture below.
So I need the to find the firmware for it to get it back and running,
I looked at few threads on here but wasn't sure if the firmware was compatible
here's an image of the system info that i got before messing the box up
Also it has 1gb ram and 4gb storage
THe box doesn't have an sd card slot only two usb ports and i have no way to enter the recovery system, that I know of.
Here a picture of the board and the back
I tried connecting the box to the computer using usb-to-usb cable howver this only gives the box power doesn't see it. But i came across this guide where i need to press on two legs on the motherboard and it shows up on the pc. Here's the pictures of the guides:
So I managed to connect the box to the computer via USB using the method that I stated above using a pin and then and connecting the usb to the pc. Howver the device is coming up as Unknown in device manager not sure if it should?
Can someone tell me how I can assess recovery or adb?
Hello,
I was able to brick my DZ09 watch when trying to upload a new firmware. I tried to fix it with several different firmware downloaded freely from the Internet. But every attempt has always ended with a 5095 error. Can you please help with their repair? These are watches with the MT6260A chip. I could not find any functional firmware anywhere on the internet and I'm afraid that the investment in the watch is already lost. The original firmware of the watch was not stored anywhere.
I opened this watch:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Motherboard: MX9-V7.0
I use full test:
All OK, NAND not present.
Before it I use Total Format in FlashTool v5.1516.00.00. Format is done, screen:
I still cant flash ANY rom downloaded from here.
I bought other DZ09, but I found the MT6260DA chip here. Also, the memory is half and even the firmware of these watches, unfortunately in my old can not be uploaded.
Thank you in advance for any help.
You solved this problem? I have same smartwatch and bricked -(. Help me please.
I am trying to backup my AC8227L alps FF-5000 android stereo in order to load new software. However, no matter what I do, I can't get the laptop to talk to the stereo using spflash tool. I opened the stereo and my board looks a lot different from the other boards that I see on the forums. there are no contacts for the VOL UP and ...
Any help is much appreciated.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
photos.app.goo.gl/Wcs5e73JTiAindwq5
photos.app.goo.gl/thdaf4zX3bB3adue7
photos.app.goo.gl/qNFbRowqFeWHQkXQ8
I have the same radio..I found the Test Point..
Help me and Ill help you with SP Flash..dont use any flashing method here, it will brick..Ill help you get to save the image
codecxbox said:
I have the same radio..I found the Test Point..
Help me and Ill help you with SP Flash..dont use any flashing method here, it will brick..Ill help you get to save the image
Click to expand...
Click to collapse
Could you help me also? I can't seem to find any information on root for this. I have (Eonon 10.1 Android HU) Alps FF-5000 AC8227l but it's really android 8.1 because it has API 27.
Hello, everyone.
I have something like the one in the picture.
I wanted to do an upgrade and .... bricked - only black screen.
I read about the TEST POINT method. I found this point on my board and. what next? I've read that I have to short it with GND - but for how long? with power on or not? if I short it with GND, can it be from power supply or some other on the board?
Can someone of you show me how exactly I should do it?
Thank you for any suggestions.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Mako1964 said:
Hello, everyone.
I have something like the one in the picture.
I wanted to do an upgrade and .... bricked - only black screen.
I read about the TEST POINT method. I found this point on my board and. what next? I've read that I have to short it with GND - but for how long? with power on or not? if I short it with GND, can it be from power supply or some other on the board?
Can someone of you show me how exactly I should do it?
Thank you for any suggestions.
View attachment 5264493
Click to expand...
Click to collapse
i'm having same issue. did you manage to unbrick it?
Try this brand new guide