Related
hi,
trying to flash the breadcrust recovery using my linux pc, but the Z1 doesn't appear in the list of devices when running adb devices. Image attached. Normally I would get a request to accept the RSA key for a trusted pc when enabling usb debug. But I don't get this option.
- Adb tools are loaded and working on my linux laptop
- My nexus 7 responds to ADB devices and shows up ok
- tried on wifes windows laptop with adb/sdk tools loaded and no joy there too
- i have developer USB debug options enabled, i've tripple checked this
could it be the cable? I'm using the one which came with the phone, so that should be ok?!!
cheers
SOLUTION - I ran this One Plus Two script modified with the Z1 device ID and now I can see my device in adb devices and interact with it. I get the SHA screen to allow access and can run commands from linux terminal. YAY!
See the attachments for script.
I think it´s a driver fault. Did u install them in windows?
im using linux, i dont get any rsa pop up confirmation either!
EggZenBeanz said:
im using linux, i dont get any rsa pop up confirmation either!
Click to expand...
Click to collapse
and that was the reason, why i installed windows last night. as long you dont get rsa pop up, the device will not listed (i think so)
EggZenBeanz said:
im using linux, i dont get any rsa pop up confirmation either!
Click to expand...
Click to collapse
But u said, that u tried ur wifes Windows notebook. Did u install the drivers there?
ADB doesn't work for me, too. I work around this problem by booting into recovery (simultaneously press Vol+ and Vol- and Power until phone vibrates) and choose "Boot to bootloader" from there. After rooting I installed "Power Toggles" from Play Store and use the toggle to reboot to recovery or bootloader.
By the way, when I boot into recovery, I'm able to ADB sideload. So I don't think there's a driver issue.
MKKLR21 said:
ADB doesn't work for me, too. I work around this problem by booting into recovery (simultaneously press Vol+ and Vol- and Power until phone vibrates) and choose "Boot to bootloader" from there. After rooting I installed "Power Toggles" from Play Store and use the toggle to reboot to recovery or bootloader.
By the way, when I boot into recovery, I'm able to ADB sideload. So I don't think there's a driver issue.
Click to expand...
Click to collapse
Good tip - I'll give it a go.
My nexus 7 works as expected on all PCs and laptops Linux/windows so it must be the phone
Sent from my Nexus 7 using Tapatalk
Maybe sudo or check this:
http://1.bp.blogspot.com/-rDdBnJTh870/U-hxVzxMf3I/AAAAAAAAKwQ/WrZkaMjaReo/s1600/Unlock-Bootloader-linux-terminal-xperia-z.png[img/]
Source: [url]http://linuxwelt.blogspot.de/2014/08/cyanogenmod-unter-linux-installieren.html[/url]
ok some progress.....
got the trusted device RSA screen to appear on my wifes windows pc. i could then run adb devices and see the device.
I could run adb reboot bootloader, but the device doesn't boot into fastboot, just reboots as normal!
I could also hold down up/down volume buttons and get into the bootloader, but again the device isn't picked by any fastboot oem checks for unlocking!!
arrrgh!!!
You'll have to add -i switch followed by the device ID to your fastboot command. I don't have it at hand, so just read the TWRP thread.
ok! Some progress...ish.
running "adb reboot bootloader"command in windows worked when I switched Cyanogen recovery updates off in developer options. The Z1 reboots into bootloader.
Running "fastboot -i 0x2b4c oem get-device-info" returns nothing just "....."
So I tried "fastboot -i 0x2b4c oem unlock" an error returns cannot unlock use command "fastboot -i 0x2b4c oem unlock-go" which works. The phone wipes data and reboots back into OS.
I re-enable the developer options and adb debug. and reboot into bootloader
Run "fastboot -i 0x2b4c flash recovery z1.twrp.2.8.7.0.By.Breadcrust-UPDATE3.img" - some time stats are retunred and OKAY message. But when I boot into recovery it's still the cyanogen stock recovery. not TWRP.
weird!
Your commands are simply wrong, thats why they don´t work.
It is:
fastboot -i 0x2b4c oem device-info
fastboot -i 0x2b4c oem unlock-go
Run "fastboot -i 0x2b4c flash recovery z1.twrp.2.8.7.0.By.Breadcrust-UPDATE3.img" - some time stats are retunred and OKAY message. But when I boot into recovery it's still the cyanogen stock recovery. not TWRP.
Click to expand...
Click to collapse
Flashing does NOT work on the international version, you have to boot into it directly from fastboot.
fastboot -i 0x2b4c boot z1.twrp.2.8.7.0.By.Breadcrust-UPDATE3.img
Should be correct instead of the flash command.
EggZenBeanz said:
ok some progress.....
got the trusted device RSA screen to appear on my wifes windows pc. i could then run adb devices and see the device.
I could run adb reboot bootloader...
...
Click to expand...
Click to collapse
What made the change? I was able to see the RSA screen only once, but after device restored to defaults I can't get it back. same drivers installed, and it appears in the device manager.
I honestly don't know, it just worked after many attempts. I read somewhere about USB 3 ports with Linux so might be the same for windows?
Sent from my Z1 using Tapatalk
It's an USB 3.0 issue. Plug the phone into an USB 2.0 port, or an USB 2.0 hub plugged into an USB 3.0 port and it will magically start working. God knows why this is the case...
Ironically, fastboot works fine even on USB 3.0...
For to be able to boot (not flash) the TWRP recovery you shouldn't need to unlock bootloader. Am I right?
Planet X said:
For to be able to boot (not flash) the TWRP recovery you shouldn't need to unlock bootloader. Am I right?
Click to expand...
Click to collapse
Booting should work.
At least it worked fine on other fastboot capable devices I've had in the past.
MrColdbird said:
Booting should work.
At least it worked fine on other fastboot capable devices I've had in the past.
Click to expand...
Click to collapse
Okay, I have found out that it is impossible to boot from TWRP as log as the bootloader is locked. It just took me 2 hours to setup my phone again after unlock.
Have a look at this thread, I am going to give it a try later.
http://forum.xda-developers.com/showthread.php?t=2408802
This did the trick on Linux (Ubuntu):
- run on terminal "sudo gedit ~/.android/adb_usb.ini"
- put "0x2b4c" in
- run on terminal "adb kill-server" and "adb start-server"
And run the fastboot commands with "sudo".
Hello all, I have a Lenovo a6000 smartphone. It was owned by my friend. She had a problem with the android os, so she went to a local store and the there it got hard bricked. Now if I turn it on it only vibrates once. no backlight or any picture. If I press and hold vol- and power buttons together LCD backlight turns on but no display. then it goes off and then again turns on. PC does not detect it. Can anyone help me getting it out from this state?
arnab8820 said:
Hello all, I have a Lenovo a6000 smartphone. It was owned by my friend. She had a problem with the android os, so she went to a local store and the there it got hard bricked. Now if I turn it on it only vibrates once. no backlight or any picture. If I press and hold vol- and power buttons together LCD backlight turns on but no display. then it goes off and then again turns on. PC does not detect it. Can anyone help me getting it out from this state?
Click to expand...
Click to collapse
Try qfil method
JovanSijacki said:
Try qfil method
Click to expand...
Click to collapse
Can you give the link please..... please note the phone is no longer detected in pc
arnab8820 said:
Can you give the link please..... please note the phone is no longer detected in pc
Click to expand...
Click to collapse
You need to have adb and fastboot drivers for your phone to correctly get detected.
Here's the LINK FOR QFIL TUTORIAL. You'll need another set of drivers called as the QCOM drivers which are mentioned in the tutorial from the above link.
Hope this helps.
I already have installed the drivers. Still not detected. Even the device manager does not show a device is connected
sasukay said:
You need to have adb and fastboot drivers for your phone to correctly get detected.
Here's the LINK FOR QFIL TUTORIAL. You'll need another set of drivers called as the QCOM drivers which are mentioned in the tutorial from the above link.
Hope this helps.
Click to expand...
Click to collapse
Here the phone connects in Qualcomm hs-USB...... mode. But in case of mine, it does not even show up in the device manager.
arnab8820 said:
Here the phone connects in Qualcomm hs-USB...... mode. But in case of mine, it does not even show up in the device manager.
Click to expand...
Click to collapse
You should try changing the usb cable you are using. Or maybe that guy in the local repair shop didn't put the sub PCB board back correctly.
sasukay said:
You should try changing the usb cable you are using. Or maybe that guy in the local repair shop didn't put the sub PCB board back correctly.
Click to expand...
Click to collapse
There is only one pcb in it. Changing the cable does not make a difference
One update. I can get into the fastboot mode. But the bootloader is locked. What to do?
arnab8820 said:
One update. I can get into the fastboot mode. But the bootloader is locked. What to do?
Click to expand...
Click to collapse
Lenovo A6000 doesn't come with a locked bootloader B-l
If you can boot into fastboot then you should flash twrp from it depending on the current android version of the device. If it had been on kitkat flash this TWRP v2.8.6.0 or if it has been updated to lollipop then flash the latest TWRP v3.1.0.
For this you need to first have the fastboot drivers installed and also the minimal adb and fastboot tool. Then place the required TWRP in that folder, better rename the file to 'recovery.img' and then in the CMD window which you open by Shift + Right Click first type
Code:
fastboot devices
To check whether your device is detected by the tool and haa got drivers installed correctly.
Later, if successful, type in
Code:
fastboot flash recovery recovery.img
Then you'll have TWRP recovery installed.
Then flash any ROM on the device using it.
sasukay said:
Lenovo A6000 doesn't come with a locked bootloader B-l
If you can boot into fastboot then you should flash twrp from it depending on the current android version of the device. If it had been on kitkat flash this TWRP v2.8.6.0 or if it has been updated to lollipop then flash the latest TWRP v3.1.0.
For this you need to first have the fastboot drivers installed and also the minimal adb and fastboot tool. Then place the required TWRP in that folder, better rename the file to 'recovery.img' and then in the CMD window which you open by Shift + Right Click first type
To check whether your device is detected by the tool and haa got drivers installed correctly.
Later, if successful, type in
Then you'll have TWRP recovery installed.
Then flash any ROM on the device using it.
Click to expand...
Click to collapse
Thanks! I will try it and post the results.
Btw are you sure it does not come with a locked bootloader? I tried to flash the stock recovery and got an error saying "unknown command or device is lock"
arnab8820 said:
Thanks! I will try it and post the results.
Btw are you sure it does not come with a locked bootloader? I tried to flash the stock recovery and got an error saying "unknown command or device is lock"
Click to expand...
Click to collapse
Yeah bro I'm 100% positive. I think unknown command is displayed when you flash the wrong version of recovery.
You can also try
Code:
fastboot boot recovery.img
Sometimes only this works which temporarily boots into the custom recovery.
sasukay said:
Yeah bro I'm 100% positive. I think unknown command is displayed when you flash the wrong version of recovery.
You can also try
Sometimes only this works which temporarily boots into the custom recovery.
Click to expand...
Click to collapse
Ok friend i will post the results tonight
sasukay said:
Lenovo A6000 doesn't come with a locked bootloader B-l
If you can boot into fastboot then you should flash twrp from it depending on the current android version of the device. If it had been on kitkat flash this TWRP v2.8.6.0 or if it has been updated to lollipop then flash the latest TWRP v3.1.0.
For this you need to first have the fastboot drivers installed and also the minimal adb and fastboot tool. Then place the required TWRP in that folder, better rename the file to 'recovery.img' and then in the CMD window which you open by Shift + Right Click first type
Code:
fastboot devices
To check whether your device is detected by the tool and haa got drivers installed correctly.
Later, if successful, type in
Code:
fastboot flash recovery recovery.img
Then you'll have TWRP recovery installed.
Then flash any ROM on the device using it.
Click to expand...
Click to collapse
Tried the above method but no luck it gives an error: "unknown command or device is lock".
arnab8820 said:
Tried the above method but no luck it gives an error: "unknown command or device is lock".
Click to expand...
Click to collapse
Try this with the CWM recovery too.
BTW does your device gets detected by fastboot devices command? Also, have you tried the QPST method?
sasukay said:
Try this with the CWM recovery too.
BTW does your device gets detected by fastboot devices command? Also, have you tried the QPST method?
Click to expand...
Click to collapse
Device gets detected by fastboot devices command. I cant try qpst because the device is not detected in any other mode except fastboot. I hv all the drivers installed
arnab8820 said:
Device gets detected by fastboot devices command. I cant try qpst because the device is not detected in any other mode except fastboot. I hv all the drivers installed
Click to expand...
Click to collapse
You've tried booting into Download mode? It requires you to press the VOL UP + POWER KEY, then you need to select the Download mode in it to perform flashing through QPST.
Also, you never mentioned what android version was the device on, earlier.
sasukay said:
You've tried booting into Download mode? It requires you to press the VOL UP + POWER KEY, then you need to select the Download mode in it to perform flashing through QPST.
Also, you never mentioned what android version was the device on, earlier.
Click to expand...
Click to collapse
If i press and hold vol up and power key together the phone only vibrates once and shows nothing. And i think my friend applied the lollipop update on it. She is not sure.
arnab8820 said:
If i press and hold vol up and power key together the phone only vibrates once and shows nothing. And i think my friend applied the lollipop update on it. She is not sure.
Click to expand...
Click to collapse
Try fastboot oem unlock
arnab8820 said:
Tried the above method but no luck it gives an error: "unknown command or device is lock".
Click to expand...
Click to collapse
I think you are missing something (maybe).
The command is "fastboot flash recovery recovery.img"
If the recovery files name is twrp.img then command will be "fastboot flash recovery twrp.img".
Hi, I've my new essential.
I can't flash a factory image, my device is dectected in fastboot, I have unlocked the bootloader, but when I click on flash-all in the image files, I have "waiting for device". I can't understand why because ALL OTHER COMMANDS have worked : fasboot flashing unlock, USB debugging, fastboot devices...
What can I do ? (In the control panel, device is detected without a yellow mark or something else. Everything should be fine.
basongwe said:
Hi, I've my new essential.
I can't flash a factory image, my device is dectected in fastboot, I have unlocked the bootloader, but when I click on flash-all in the image files, I have "waiting for device". I can't understand why because ALL OTHER COMMANDS have worked : fasboot flashing unlock, USB debugging, fastboot devices...
What can I do ? (In the control panel, device is detected without a yellow mark or something else. Everything should be fine.
Click to expand...
Click to collapse
Still seems like a driver issue. While in bootloader, you could confirm this by trying the command "fastboot devices". If nothing shows then check your device manager. If you are seeing Mata, it's your issue. For some reason every few times I plug in, it'll default back to that and have to manually update the driver to the bootloader driver. Just choose from list of installed drivers as the update method.
Also, if you have USB 2 ports, try one of those. I couldn't get anything to flash when I had it plugged in one of my USB 3 ports.
Could be cable issue, USB port issue, driver issue or you can try updating your adb setup etc... I used the Minimal ADB and Fastboot. Mine was out of date and wouldn't recognize device in fastboot after the Oreo sideload.
Works perfectly with the Essential official drivers in Win8.1Pro now.
The cable is brand new by anker, and works perfectly. Drivers and adb are updated.
mrcooter said:
Still seems like a driver issue. While in bootloader, you could confirm this by trying the command "fastboot devices". If nothing shows then check your device manager. If you are seeing Mata, it's your issue. For some reason every few times I plug in, it'll default back to that and have to manually update the driver to the bootloader driver. Just choose from list of installed drivers as the update method.
Click to expand...
Click to collapse
and fastboot devices works properly. But i've noticed that I wanna flash the same build that I had, maybe that ?
basongwe said:
and fastboot devices works properly. But i've noticed that I wanna flash the same build that I had, maybe that ?
Click to expand...
Click to collapse
Something that was odd that may help (assumed it was just my environment setup). I had adb installed to C:\adb and only way fastboot will work consistently for me is to run commands from that directory. Could be unrelated but thought I would mention it.
basongwe said:
Hi, I've my new essential.
I can't flash a factory image, my device is dectected in fastboot, I have unlocked the bootloader, but when I click on flash-all in the image files, I have "waiting for device". I can't understand why because ALL OTHER COMMANDS have worked : fasboot flashing unlock, USB debugging, fastboot devices...
What can I do ? (In the control panel, device is detected without a yellow mark or something else. Everything should be fine.
Click to expand...
Click to collapse
Try copying fastboot to the folder that has the flash all.bat
What operating system?
Where did you get your driver's?
Reason I ask is at first I had driver's auto install from a Samsung device that I used previously. Caused an issue where it wouldn't start the fastboot process and device got stuck at first step.
Take the system driver of your operating system from essential homepage... Was the trick for me
Link: https://www.essential.com/developer/current-builds
vergilbt said:
Take the system driver of your operating system from essential homepage... Was the trick for me
Link: https://www.essential.com/developer/current-builds
Click to expand...
Click to collapse
This also did the trick for me
You're welcome...
Edit : I have it(drivers from essential website)
Try "fastboot -i 0x2e17 <whatever command here>" it worked for me I wasn't able to unlock my bootloader until I found that command in a random website.
723i said:
Try "fastboot -i 0x2e17 <whatever command here>" it worked for me I wasn't able to unlock my bootloader until I found that command in a random website.
Click to expand...
Click to collapse
That did the trick.
723i said:
Try "fastboot -i 0x2e17 <whatever command here>" it worked for me I wasn't able to unlock my bootloader until I found that command in a random website.
Click to expand...
Click to collapse
command result: "fastboot: unknown option -- i"
not worked for me
mine is on the latest pie update
un1ocked said:
command result: "fastboot: unknown option -- i"
not worked for me
mine is on the latest pie update
Click to expand...
Click to collapse
It's always recommended to use the adb/fastboot provided by Essential (gets installed along with the Windows driver). From the error message, it looks like you are using a different fastboot executable. If you have more than one adb/fastboot package installed on your PC, make sure to use the one from Essential. You can see the path to the executable by running "fastboot --version".
kt-Froggy said:
It's always recommended to use the adb/fastboot provided by Essential (gets installed along with the Windows driver). From the error message, it looks like you are using a different fastboot executable. If you have more than one adb/fastboot package installed on your PC, make sure to use the one from Essential. You can see the path to the executable by running "fastboot --version".
Click to expand...
Click to collapse
fastboot version 28.0.3-5475833
Installed as C:\Program Files (x86)\Essential\ADB\fastboot.exe
EDIT:
problem solved by switching to an old PC with a pure usb 2.0 port
un1ocked said:
problem solved by switching to an old PC with a pure usb 2.0 port
Click to expand...
Click to collapse
Ahh... Yeah, that's often the issue. Still doesn't make a lot of sense to me, because your error msg was "unsupported option". Well, good that it worked for you.
I am using Oreo.
But there are too many bugs.
So I want to downgrade.
I want to go back to 7.1.
I tried to find a way.
I do not really know.
Press Volume Down + Power to enter fast boot mode.
With ADB, if you use 'fastboot devices'
Nothing happens.
Developer option, OEM off, all done.
I want to know how to downgrade.
yuhanyanghaeng said:
I am using Oreo.
But there are too many bugs.
So I want to downgrade.
I want to go back to 7.1.
I tried to find a way.
I do not really know.
Press Volume Down + Power to enter fast boot mode.
With ADB, if you use 'fastboot devices'
Nothing happens.
Developer option, OEM off, all done.
I want to know how to downgrade.
Click to expand...
Click to collapse
Follow the instruction provided by Essential:
https://www.essential.com/developer/current-builds
Developer otpion and OEM unlocking are off? Why? That shouldnt be needed.
Download current build from link provide above ^^(current build)
extract the files to your "adb/fastboot/platform tools folder on pc"
connect the phone to computer using usb cable.
Open adb on computer
type adb reboot bootloader
when in bootloader verify fastboot works
"fastboot devices"
if your device shows up double click the flash all script for your OS.
Profit
Hi
By me the same.
When I Type adb reboot Bootloader the Phone starts new and boot up the system.
When I manually Boot into Bootloader the Phone were not found in Fastboot.
Developer option, OEMunlocking , all on.
samy1111 said:
Hi
By me the same.
When I Type adb reboot Bootloader the Phone starts new and boot up the system.
When I manually Boot into Bootloader the Phone were not found in Fastboot.
Developer option, OEMunlocking , all on.
Click to expand...
Click to collapse
I had the same problem. adb worked, fastboot did not. Installing the PH-1 drivers from the Essential support site fixed it.
Hi.
Recently I decided to flash lineage os 15.1 on my MiA1
For that I have downgrade to Android nougat.
After downgrading I booted my device.
After setting up device I booted device in fastboot mode to follow further steps like flashing TWRP and all but the problem is my device goes in fastboot mode and it is not identified by abd and after that it is automatically getting restarted and is not holding in fastboot mode.
Please help??
Odd issue. What are you using to flash? If you are using XiaoMiFlash.exe, you'll want to try the (THIS WILL REMOVE ALL YOUR DATA) "clean all" option. Please note that this removes all your data.
I have used MiFlash tool for this and now My device automatically reboot from fastboot mode so I am not able to use adb as well to flash rom or twrp also Now MiFlash tool is not recognising the device.
MrUsamahh said:
I have used MiFlash tool for this and now My device automatically reboot from fastboot mode so I am not able to use adb as well to flash rom or twrp also Now MiFlash tool is not recognising the device.
Click to expand...
Click to collapse
Hmm. What ROM version are you trying to flash on this? If your device isn't recognized by your PC when in fastboot mode, I'm not sure how you'd flash it.
oreo27 said:
Hmm. What ROM version are you trying to flash on this? If your device isn't recognized by your PC when in fastboot mode, I'm not sure how you'd flash it.
Click to expand...
Click to collapse
I flashed Android N Fastboot rom by selecting Clean and lock option.
After that the problem started
MrUsamahh said:
I flashed Android N Fastboot rom by selecting Clean and lock option.
After that the problem started
Click to expand...
Click to collapse
It should boot if you've fully flashed it and cleaned the user data partition. If it still isn't, you'll want to wait for other members with more experience in bricks to chime in.
oreo27 said:
It should boot if you've fully flashed it and cleaned the user data partition. If it still isn't, you'll want to wait for other members with more experience in bricks to chime in.
Click to expand...
Click to collapse
My device is booting up without any problems.
But the problem is bootloader is still unlocked. So i am not able to update via OTA.
And as the device does not holds in fastboot mode so I am not able to do other flash work.
Is there any way I can share a video of my problem with you?
MrUsamahh said:
My device is booting up without any problems.
But the problem is bootloader is still unlocked. So i am not able to update via OTA.
And as the device does not holds in fastboot mode so I am not able to do other flash work.
Is there any way I can share a video of my problem with you?
Click to expand...
Click to collapse
Oh. If it's booting up fine, then you shouldn't be worried too much.
If it keeps restarting in Fastboot mode, it could be a driver issue which is preventing your PC from recognizing your device and vice versa. I'm on Windows 10 which installs drivers automatically so I've never had experience with it.
oreo27 said:
Oh. If it's booting up fine, then you shouldn't be worried too much.
If it keeps restarting in Fastboot mode, it could be a driver issue which is preventing your PC from recognizing your device and vice versa. I'm on Windows 10 which installs drivers automatically so I've never had experience with it.
Click to expand...
Click to collapse
https://photos.app.goo.gl/TyLendNH7XaY74bs1
Please see this video.
If i boot in fastboot mode the device should be in fastboot mode till power button is not pressed for at least 10 seconds.
But in this case it gets switched off.
I have not connected the USB to pc and nothing else.
MrUsamahh said:
https://photos.app.goo.gl/TyLendNH7XaY74bs1
Please see this video.
If i boot in fastboot mode the device should be in fastboot mode till power button is not pressed for at least 10 seconds.
But in this case it gets switched off.
I have not connected the USB to pc and nothing else.
Click to expand...
Click to collapse
I think that's expected behavior? If it doesn't recognize itself being connected to a device, it'll exit fastboot mode.
I think you need to connect it to the USB cable and into your PC for it to not restart/power off.
oreo27 said:
I think that's expected behavior? If it doesn't recognize itself being connected to a device, it'll exit fastboot mode.
I think you need to connect it to the USB cable and into your PC for it to not restart/power off.
Click to expand...
Click to collapse
No when I connect it to pc at that time also same happens.
Previously when booted in fastboot mode it will stay ther by the time juice is out.
MrUsamahh said:
No when I connect it to pc at that time also same happens.
Previously when booted in fastboot mode it will stay ther by the time juice is out.
Click to expand...
Click to collapse
Yup. I just tested it out. It looks like you're right.
oreo27 said:
Yup. I just tested it out. It looks like you're right.
Click to expand...
Click to collapse
So do you know how can I help myself out?
wait.. what exacly did you do when you booted into fastboot? did you type "adb devices" or "fastboot devices"? also, try rebooting into fastboot mode by typing "adb reboot bootloader" in cmd, with your phone plugged into your pc, and with the proper platform-tools installed. it shouldn't really go away from fastboot mode like that.
Mizuru said:
wait.. what exacly did you do when you booted into fastboot? did you type "adb devices" or "fastboot devices"? also, try rebooting into fastboot mode by typing "adb reboot bootloader" in cmd, with your phone plugged into your pc, and with the proper platform-tools installed. it shouldn't really go away from fastboot mode like that.
Click to expand...
Click to collapse
Hy man, I know basic of adb and I use cmd "adb devices"
My device is recognised when it is on.
I can also give various cmd like boot in recovery or fastboot mode or reboot and the device follow the instructions.
Please see the video that I've shared.
Once fastboot mode is on the device is automatically restarted in about 10 to 15 sec and within this time MiFlash tool or adb cmd prompt bot does not recognise my device.
I have tried to flash OTA via adb side load but it is showing error.
Help me with your input!
MrUsamahh said:
Hy man, I know basic of adb and I use cmd "adb devices"
My device is recognised when it is on.
I can also give various cmd like boot in recovery or fastboot mode or reboot and the device follow the instructions.
Please see the video that I've shared.
Once fastboot mode is on the device is automatically restarted in about 10 to 15 sec and within this time MiFlash tool or adb cmd prompt bot does not recognise my device.
I have tried to flash OTA via adb side load but it is showing error.
Help me with your input!
Click to expand...
Click to collapse
Your device doesn't get detected in your CMD prompt when it's in fastboot AND you type "fastboot devices"?
If it doesnt then you might have flashed something incorrectly.
Also, make sure to have your android drivers up to date in your pc. It's very, very likely that you don't have them installed on your PC, or they are outdated. See this: https://developer.android.com/studio/run/oem-usb.html
And this: https://developer.android.com/studio/releases/platform-tools.html
I have faced this issue. Yesterday i dirty flashed a custom rom. but i forgot how to dirty flash. i just simply flashed the rom and restarted the phone. it was mandatory to flash custom recovery and gapps after flashing a rom dirtily or normally. but i didn't. After the reboot completed, i remembered that i didn't flashed the twrp and gapps. So, i go back recovery mod, guessed i could flash twrp now. But i didn't see any custom recovery on my phone. But the phone boots, and i can use the phone. Still, i'm on that phone, while i'm typing this comment. i didn't lost my data cause i flashed dirtily. But the problem is, as i didn't flashed gapps or magisk (for root access), now i can't use google apps like, play store, and more. As i don't have root access on my phone so, i can't run flasify, to flash custom recovery. neither i can run other apps that need root. As i didn't flash custom recovery, now i can't flash gapps, magisk and whatever that needs a custom recovery.
I told some rom porter about the matter. They told me to flash stock rom. So, i was trying to flash stock rom. but flashing stock rom requires a fastboot mode. But my fastboot logo doesn't appear and it's blank. I told this to a rom porter. But he said, He doesn't know about that and he can't help.