Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
i don't know. i just know my dog ate mine and i'm now in the market for a new screen, so if you don't get it working sell me the unit and get some money for yourself to purchase a new one =D
or you could google the disassembly instructions and try unplugging the battery, not very hard to do. could be of .. some help perhaps?
I would definitely take you up on your offer, but i'm still under warranty.
However, I would still like to have my original, and figure out what is going on and why it happened.
Ideas?
Thank you.
similar problem were solved
Hi! I might have read about similar problem solved on USB host mode here http://forum.xda-developers.com/showpost.php?p=23475998&postcount=131
That's it, thanks so much.
if it help
if it helps let them know in the tread that you had same problem. they are wondering whether it is due to host mode
[N2E]: After automatic update to 1.1, Nook Touch Screen absolutely DEAD--Nothing Work
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Identical problem.... and no fix..
It is a shame you got no solution for this. and the worst, you are not the only one... it happened exactly the same with my Nook ST....
Hopeless...
Machiavelli_The_Man said:
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Click to expand...
Click to collapse
The factory restore does not actually fix every possible problem with your Nook.
If your Nook responds at all, try to boot it up on an SD card like ClockworkMod or noogie.
At least that way you can see what is happening.
The partitioning might have become corrupted which the "factory restore" does not touch.
If no response with anything, try disconnecting the battery.
You might also try booting over USB using the techniques in rooting the new white glow.
Hello I was wondering if I'm just screwed I bought 2 nook simple touch, one for me and one for a present to my mother for her birthday on march 16. I bought them at best buy for $40 a piece on January 30. I used mine and was perfect but when I tried to set up my mom it wouldn't load the license agreement, always got stuck or reboot or something, so I loaded cwm on an sd card just to play around, tested on my nook and was fine, then put it on my moms nook booted once then I didn't press anything and turn it off then I load the image but when I tried to boot again it got stuck on the load screen and wont do anything, no reset sequence will work with the sd card on or off the other nook boots with this sd card. at the end I exchanged with my mom she is happy with her nook an I have a useless unit do you think they will exchange it I didn't rooted it or did anything to it but has the n cwm splash on screen forever. I'm in Costa Rica right now and wont return home until May do you think I'll might be able to exchange it or should I just try to repair it.
I'm glad that your mother got the working one!
You say that that one will boot on your CWM SD card, but yours won't?
It may be hard to get your unit exchanged with a conspicuous screen on it, even if it's not your fault.
When you plug it into your desktop is there any indication of a new USB device found?
If it's charged and no amount of the power button gets a reaction, I'd open it up.
any news???
Hi endor43, same problem here, have been able to find any solution?
endor43 said:
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
Click to expand...
Click to collapse
There are times when a Nook gets in a mode where it won't accept a charge.
Opening it up and disconnecting the battery for a minute might fix this.
endor43 said:
That's it, thanks so much.
Click to expand...
Click to collapse
When this worked for you did the light turn orange right when you plugged the battery back in? I just took the battery out, plugged the nook into a charger, and with it plugged in plugged the battery back in and the light stays green the whole time yet I'm not able to use the nook at all.
My nook second generation is not responding to my touch I tried everything to get it to work and I eventually got it to completely power of what if it does not work when I turn it on what should I do
It could be power/battery problems.
Check to see if it makes itself known when the USB is plugged in.
If it reacts at all, that's an indication of life.
Hey,
This is my first time posting here and really using the site. I have the Sprint Galaxy S4 and just updated to the SlimKat official build 7 and had no initial problems. A day later it starts to reboot constantly and would stay on for a couple minutes. Now it is stuck in a bootloop and will shut off even when going into download or recovery mode. When plugged into a computer the computer won't even recognize the phone and the phone will not turn on. The only time the phone will even start to boot is when it is not plugged into wall/computer and on battery. I have no idea what to do now.
That's a tough one. Usually with a soft brick, if you can make it to recovery, your phone can be saved but since you can't... I hope you get it working!
Sent from my SPH-L720 using XDA Free mobile app
puresublimie said:
Hey,
This is my first time posting here and really using the site. I have the Sprint Galaxy S4 and just updated to the SlimKat official build 7 and had no initial problems. A day later it starts to reboot constantly and would stay on for a couple minutes. Now it is stuck in a bootloop and will shut off even when going into download or recovery mode. When plugged into a computer the computer won't even recognize the phone and the phone will not turn on. The only time the phone will even start to boot is when it is not plugged into wall/computer and on battery. I have no idea what to do now.
Click to expand...
Click to collapse
Go to sprint galaxy s4 thread. All answers there. You need Odin 3.09 then stock ng2 tar. To flash through computer.
Sent from my SPH-L720 using XDA Free mobile app
I already have odin and the tar files for stock. When plugged into my computer it will not even register that it is connected and so I can't use odin to flash it.
The same thing is happening to me. I get to the Galaxy S4 splash screen, then it shuts off. Even if I try to boot into recovery
I'm going to pile on in here as I seem to be having a similar issue. I had my S4 (not rooted, stock rom) on my dock streaming google music. A phone call came in and the phone started vibrating like crazy and wouldn't stop. The screen shut off and the phone was still vibrating. Finally it stopped and was shut off. When I try to start it a few things happens. It will sometimes boot to my lock screen and the screen goes black and I think it is powered off. Sometimes it will get past the lock screen and then die shortly after. After like 2 or 3 times of that it won't even boot. It loads the Samsung screen but never gets to the Sprint screen or boots. If I leave it for some time shut off with battery out it will go back to booting to the lock screen then dying etc... When I press the buttons to get into recovery it says recovery is loading and then the screen goes black. I swapped batteries and that didn't do anything. I tried pressing the menu button or the home button to try and boot safe mode and it just loads normally not that I think that would help anyway.
Any ideas on things I can try next? What is this odin thing? Would that work for me?
---------- Post added at 07:09 PM ---------- Previous post was at 06:16 PM ----------
Ok... I can get into recovery now and will try a factory reset. Are you sure you are going into recovery correctly. Apparently I was not. Hold volume up power and menu button and when the phone vibrates let go of power only.
Before I do a hard wipe is there any way to get data off the internal memory from recovery mode?
So I got a custom recovery installed, reinstalled stock rom, things worked ok for awhile. Then it started random reboots every 10 mins or so. Now it is back to instant crashing and rebooting. Any idea what could be the issue? I'm assuming at this point it is hardware related. Why can recovery and download mode run consistently without crashing but when an os is fired up it has issues? If it was a hardware issue shouldn't it not work across the board?
So I had Sprint replace my phone on the 8th. I have been using my same batteries (1 stock 1 Anker) and chargers (some stock some not) without issue the past 5 days. I rooted and installed xposed and some modules (original broken phone was never rooted and was completely stock). Things were going great until tonight when it started reboot looping exactly like the old phone. I switched battery and same proble. After I took the battery out and left it out awhile it fired back up but I'm afraid the problem will return. Is it possible that the battery or charger randomly are causing damage to the phone? I only have 14 day warranty on this replacement and need to figure this out.
So things were going well for awhile and then the reboot loops started up again. I did some digging and read that apparently Samsung phones are notorious for sticking power buttons and the symptoms were exactly what I was experiencing. I watched some videos online how to open the phone and clean out the power button but it didn't make a difference. I then read that squeezing the connector for the power button with a pair of pliers sometimes does the trick. Not for me. So finally since I'm not under warranty, have no insurance, and the phone wasn't working anyway, I just ripped the white plastic part of the power button right off. Well, that seemed to do the trick. Phone immediately fired back up without issue and has been going strong. I glued a small thin piece of plastic where the old one used to be and I am back in action. If my little plastic piece solution eventually fails or breaks off I will consider soldering on a new button but so far so good.
If you have tried everything else, and are looking for last resort, try cleaning the power button with some alcohol, and if that fails, rip off that power button! Here is the video that gave me the idea: https://www.youtube.com/watch?v=3Glllc7bEJs and here are some other power button videos: https://www.youtube.com/results?search_query=s4%20power%20button&search_type=&aq=f&oq=
so i have bought a brand new OP 5. did the latest update to O2 os 4.5.5 and considered doing a hard reset as i have spent a good amount of time with windows phone and a reset was just another ritual there after a ota update.
so i set the device to do a clean reset with wiping of all the data. the device rebooted to the red dot and 2 with dots revolving around it and then after a few seconds rebooted again . as it was late night already i decided to leave it resetting and will set it up later in the morning.
for my surprise when i woke a hour or 2 later i saw the phone is still in the same condition with the two dots revolving around in circles. and the device was super hot around the camera lens region. i didn't wanted to disturb the process so i kept the phone upside down to get it to cool down and went back to bed once again.
when i woke up in the morning and tried switching on my phone it showed a warning sign which read " low battery cannot boot" for a sec and died again. so i connected the charger and the phone booted up with the normal setup screen.
so what just happened? i thought of recreating the issue and i was able to reproduce it again when i charged the phone back to 90% i again set it to factory reset and alas again the thing got stuck in a loop where the two white dots kept circling around. this time i held the power button and the phone switched off but when i turned it on it went straight to the setup screen.
i can still recreate this issue and is seriously bothering me as what is the issue, my knowledge tells me this must be a software bug but is anyone else facing it? though a proper reset happens once in a while where the phone itself boots up to the setup screen but most of the times the device will be stuck on the rotating dots screen.
any help / suggestions / explanations will be much appreciated .
I had the same issue when i reset my phone
Oops Reseting leads to bootloop ??
Same thing happened to me as well. Stuck on bootloop