Hello, I install the android SDK correctly and install all correct drivers, all correct files from the google repository, and reading on unlockr, you need to type CMD and enter a few commands, the final one being ADB devices, which is meant to bring up your device serial/id but doesnt show nothing for me, i deleted all drivers with a program, and it re-installs them, I put the phone into debug mode too, but whatever i try, i cant root my magic (32B), please help!!!!
i have followed every single guide but cant blooming root my phone!!!
HELP!!!!!!!!
Install the HTC Sync software first. If this connects correctly and recognizes your phone, then the ADB will find it too. I use it as a test, whether the drivers are installed correctly or not.
To start the ADB, you have to navigate to the folder where the SDK was extracted using the CMD Prompt, and then into /tools. There you type ADB and the command you want to execute.
done that mate, going to /tools and then adb devices and its meant to say a device serial, but on mine it shows nothing
As far as I know, you have to have a recovery installed to access adb.
Write "fastboot devices" while in /tools to see if the drivers are OK. When you install a recovery, adb should be accessible.
I've finally decided to try to root my G2 but can't get past the ADB setup. I downloaded the SDK, but when I open the manager and try to install platform tools it goes through the motions and then tells me nothing was installed. When I open a command prompt and type "ADB devices" it doesn't recognize anything. What am I doing wrong??
EDIT: specifically, when I try to install platform-tools it tells me it couldn't create a directory and nothing was installed.
66 people have read this and nobody has any suggestions to help?
i think you miss the 1st procedure....
you must have the unknown resources and the usb debbuging enabled.....
then you can proceed to your super one click rooting.....
I have a problem after rebooting my PC: <Java not found...> Reinstalling doesn't help, adding environment variables too. Any idea?
Just root using the rage/visionary method. No adb needed and very easy to do. Here is the linkhttp://forum.xda-developers.com/showthread.php?t=834228
Sent from my SilverBullet 'HTCDesireZ running CM7'
juvanni said:
i think you miss the 1st procedure....
you must have the unknown resources and the usb debbuging enabled.....
then you can proceed to your super one click rooting.....
Click to expand...
Click to collapse
I don't understand? I'm trying to root following the recommended wiki instructions, and I haven't been able to get adb to work so I haven't gotten past that step.
Are you running windows x64? Cause the android installer has issues detecting java on x64 systems.
When it says 'Can't find java' or whatever the error is, click back, then next again, it should find it the second time around. Well thats what happened for me anyway.
-Nipqer
If you're on froyo just use the app z4 root or universal androot
You can also use superoneclick root 2.11
Its very easy and it only take about 3 minutes
Stewie just said that!
I appreciate the help so far, but my problem is I have gingerbread and everything I've read requires froyo for root, and the only way I've read to downgrade uses ADB, so any non-ADB rooting method still won't work for me. I've followed the "ADB for dummies" thread and the other instruction thread and everything seems fine, but when I type in the first command for the downgrading it says adb isn't a recognized command. Am I in the wrong command prompt? I feel like its probably something really dumb I'm doing or not doing but for the life of me I can't figure it out.
Navigate to the folder adb is in.
Hold shift, right click in the folder (make sure nothing is selected)
select 'Open command window here' (or something along those lines)
Adb should work.
-Nipqer
OK, so I'm definitely in the right folder, I read and followed ADB for Dummies thread. Trying to follow this direction:
"Run the following command to verify the exploit has access to what it needs. (Only the first line is the command. The second line should be the result returned if all goes well.)
Code:
$ adb shell cat /dev/msm_rotator
/dev/msm_rotator: invalid length"
When I type that in, should there be spaces between the "adb" and "shell"? Should there be a space after the command prompt and before "adb"? I've tried several variations of it and it keeps telling me "adb is not recognized as an internal or external operable program or batch file."
ok you need to run the command from the folder with adb.exe in it, type it as adb<space>shell<space>cat<space>/dev/msm_rotator
If you are getting an error search for adb.exe and once found try the command again from this folder,if as you say you are in the right folder then I think you will have to reinstall adb as I just ran the command in the form above and it works so if you still get an error then something has gone wrong with the install
P.S Another way to make sure that adb is working and recognises your phone is to type adb devices, if your phone is attached and recognised then it will return a number
Thank you! I had to uninstall and reinstall the package, I don't know what was wrong but it seems to be working now. Also, I knew I was probably doing something stupid, and I was. I wasn't in the platform-tools directory for my command prompt, I was in the TOOLs directory. Just so I'm clear, every command I type into the terminal should be in the Platform-tools directory, correct?
Now, assuming I can follow all the other directions with no problems, once I get to the downgrade pushing steps, I will lose all my current settings, right? It will be a fresh froyo 2.2 like it came to me originally? Other than using Appbrain to back up my current apps, how else should I make a backup?
Final question, do I need to follow the temp root directions and push the downgrade all at one time? Or can I do the temp root and come back at a later time to push the downgrade?
First problem solved then!
Yes but follow this Step 4
Now we need to update your Path variable. This lets you run adb on your PC from a command window no matter which directory you are in (which makes things a lot easier). If you don't setup your Path, then every time you want to run adb, you will either have to type the whole long pathname where you put adb, or cd to where you've put adb and run it from there (which could be inconvenient if you are transferring files to/from your phone).
On your PC, right-click on "My Computer" and select "Properties". (on Vista, click on "Change Settings"). Go to the "Advanced" tab, then select "Environment Variables". Find the "Path" variable in the list of variables that it shows (you might need to scroll), and then double-click on that entry to edit it. Add the full path of the "tools" and "platform-tools" folders of the SDK to your path. e.g. if the SDK has been installed in "c:\Program Files\android-sdk-windows", then add to your Path "c:\Program Files\android-sdk-windows\tools;c:\Program Files\android-sdk-windows\platform-tools" (Please Note - don't put any spaces between the semi-colon and pathname, otherwise it won't work !)if you want to.
Once done you can use ADB from the command prompt in ANY folder,very handy IMO.
If I was you I would set aside enough time and see it through,no point to temp rooting alone.
Get Titanium backup from the market an absolute essential app with this you can backup,upload to dropbox(Another essential app) uninstall apps and a host of other useful tools.
Read the guide first as well,good luck.
Okay, this guide is for users with less experience and want to overclock their Kindle Fire. This is for Windows.
This section is if you haven't installed ADB yet
1) You need to download the Android SDK
Android SDK: http://developer.android.com/sdk/index.html
2) Open the SDK Manager and install the SDK Tools and SDK Platform Tools
3) You need to add the ADB path. First find where you installed the Android SDK.The default is in C:\Program Files\Android\Android-sdk or C:\Program Files (x86)\Android\Android-sdk, you can check in the SDK Manager at the top, it will tell you your path. Then click on the start button, and right click on my computer and hit properties. Then on the left click Advanced System Settings In the next box at the bottom is Environment Variables click on this. Under System Variables find the variable that says Path DO NOT DELETE THIS VARIABLE! Hit Edit and at the the end put:
;YOUR ANDROID SDK PATH\tools;YOUR ANDROID SDK PATH\platform-tools
Then hit OK.
ADB install tutorial is now finished
4)Now we want to add the correct drivers. There are a couple of ways to do this, this is the way I do it. Again right click on My Computer, and click properties. Now in the top left corner is Device Manager click on this. Now find where it says Kindle and right click it. Click the drivers tab and then Update Drivers and then browse my computer for driver software. Then click, let me choose from a list on my computer and click adb interface, and then either a ADB Testing Interface, or fastboot Interface, both work for what we are doing.
5) The next thing you want is a kernel so download and put in the \platform-tools folder.
IntersectRaven's: http://forum.xda-developers.com/showthread.php?t=1382999
DoomLord's: http://forum.xda-developers.com/showthread.php?t=1372625
6) Plug your Kindle Fire into your computer
7) Open a CMD window. Hit start and run CMD.exe or search for CMD. Then type into cmd:
adb shell
idme bootmode 4002
reboot
8) Open another CMD and type cd YOUR ANDROID SDK PATH \platform-tools. Then type:
fastboot boot NAME OF KERNEL.img
9) Now your Kindle will reboot, make sure it boots! Now that you have verified that it works we are ready to flash it.
10) Shutdown your Kindle Fire.
11) Use your old CMD with fastboot, and type:
fastboot flash boot NAME OF KERNEL.img
12) It will probably get stuck in booting at this point. With the fastboot CMD type:
fastboot oem idme bootmode 4000
it will say waiting for device, do not close this CMD!
13) Now hold down the power button until your device turns off. Then turn it on again, and the command will register.
14) Let your Kindle Fire boot and enjoy your new kernel!
If this doesn't work please leave a comment, or if I forgot anything, I am kind of tired while writing this. I may add pictures later. Thanks!
All this does is boots the custom kernel a single time (which you MUST do to test it). You still need to flash it.
Sent from my Gingervolt-ed VS910 4G using xda premium
Sorry, I will add the rest soon, slipped my tired mind.
do we really need the whole android and java sdk ?
the only commands used is adb and fastboot.
woud'nt the tools directory of KFU be enough since it contains the necessary commands ?
furthermore the driver installation is a essential part for correct operation of adb and fastboot
and don't forget so say your how-to is for windows
I haven't looked at the KFU much yet, so I don't know. I added that it is for windows and removed the java sdk. And added how to flash the kernel.
Accessory mode suppot
Are any Fire kernels available that support Accessory Mode aka ADK.
The changes that need to be made to the kernel are available from Google. They are in the main 3.x kernel source tree and in the samsung source tree of the 2.6.35 kernel.
Not sure if this will help anyone, but I had a problem when rooting my new kindle fire 6.2.1
If you tried the Burrito Root method, I saw some few mistakes that I've done or didn't see in the video.
1. Updating the Kindle Drivers
I had previously rooted my android phone before, so when I plugged the kindle fire on my windows 7 laptop, I noticed that the windows was already indetifying it as an android phone, and had already labeled it for ADB. This auto-driver update thing might work for some people, but I find much better success replacing that driver that your computer identifies Kindle as, with the one that the BurritoRoot driver provides.
2. Getting the Kindle Root in the Listed Devices of ADB in command prompt.
This was probably the biggest issue I had when rooting the Kindle Fire. I was scratching my head, thinking why my Kindle Fire wasn't listed in the command prompt after typing "adb devices." I knew I did everything right from the beginning. Or so I thought?
One way I found that fixed that was downloading the Kindle Fire Utility v0.9.1
Unlucky for me, the download link was gone....
LUCKY for me, a fellow member here uploaded a mirror.
I somehow got it to work, with just luck but figured out the exact steps that seem to work for me (on Win 7 64 bit here).
1) Open up command prompt again, do the cd c:\KindleADB etc... upto the point where you typed in adb devices. you should be seeing no listed devices on the cmd (if you have that problem). LEAVE IT OPEN.
2) DOwnload the kindle fire utility, open the run.bat , it should have a message saying daemon started sucessfully, THEN QUICKLY FOLLOW THE NEXT STEP.
3) When the daemon started successfully message popped up on the KFU, go back to your CMD where you typed in adb devices and quickly type in "adb devices" again. it should say something like, killing out of date, starting daemon, and something about successful (Sorry if I'm not that much of a help, I tend to forget what the exact message said).
4) It should list the device. if not type it again.
5) Walla ! it should show a bunch of numbers, under listed devices.
3. Rooting the Kindle Fire in command prompt ERRORS
This wasn't much of a problem as it really was my mistake. I kept getting error messages when i typed in ADB ROOT in the command prompt during the BurritoRoot rooting method.
1) You have to make sure you have the BurritoRoot app installed in your kindle fire before starting the CMD adb root part. The app will tell you when to start typing away in CMD!
2) If you're doing the burritoroot method, you have to make sure you got all the names and directory right.
3) When you're doing the CMD adb root part, copy and paste it usually the best way to do it in CMD to avoid mistakes and erorrs! And no, you don't press CTRL+V in CMD. Rather, you right-click the CMD , then click paste (after copying the line you want to input).
adb remount
adb push su /system/xbin/su
adb shell chown 0.0 /system/xbin/su
adb shell chmod 06755 /system/xbin/su
adb install com.noshufou.android.su-1.apk
adb reboot
Notice all those commands above that you're suppose to type in (or copy and paste). The ones I bolded, people tend to make mistakes there. When you put those files you downloaded into KindleADB, PLEASE MAKE SURE IT IS NAMED com.noshufou.android.su-1.apk, otherwise when you get to the part
Code:
adb install [B]com.noshufou.android.su-1.apk[/B]
change it to :
adb install WHATEVER IT IS CALLED.apk that is Superuser.
The most important part is to push the SU file (that has no file extension).
I had my kindle rooted, with Superuser installed, but I couldn't get any pop-ups from Superuser asking permission for any apps! That is, until I found out I forgot to push the su file to /system/xbin/su and other steps to chmod it.
Anyways, I hope this helps anyone that goes through any problem like I did above. If not, sorry to waste your time! If you guys have any other problems, please leave a question below and perhaps I could or a fellow member here could help you.
Thanks again!
http://forum.xda-developers.com/showthread.php?t=1417234
Please note, I can only speak with any degree of certainty about devices bought from Play / Moto. I cannot attest to the accuracy of this information for US carrier versions etc. Anything you do is at your own risk
Contents / Thread overview
Introduction
What is Fastboot?
What is adb?
How to install adb and fastboot
How to test adb and fastboot work
OK Gimme some useful fastboot commands please!
OK Gimme some useful adb commands please!
A little more about using Windows command prompt
Myth Busters
Introduction
adb and fastboot are very useful command line tools. They can be used from Windows, Linux or Mac to carry out tasks on your android device, such as moving and backing up files, rooting and restoring your phone to it's factory state. Understanding how to use these tools could save your phone when you get yourself in trouble. This is especially true of rooted users. Particularly those of you who are "new to the scene". You definitely should read and understand this thread before you do ANYTHING root related.
This thread is not intended to be a non-exhausted reference. It is merely here to give an overview of the most basic of basics
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
What is fastboot?
Fastboot comprises of 2 components.
1) Fastboot mode on the phone (The Bootloader)
2) Fastboot tool on your computer
Fastboot is a small command line tool that you can use from your computer whilst the phone is connected via USB and you are booted into the bootloader. The most common uses for fastboot are:
Unlocking the bootloader - needed as part of the rooting process
Flashing a custom recovery to the device - needed as part of the rooting process
Flashing factory images - used for saving / trestoring your device back to stock
Being able to do these 3 things are essential before rooting. Many new users skip learning these and use a toolkit to root. As a result, when they mess up and we try to explain what they need to do to fix their issues, it becomes very difficult for us to help as fastboot is not understood. It is YOUR responsibility to understand these things BEFORE you mess up.
What is adb?
adb is another small command line tool that stands for "Android Debugging Bridge". Again, it can be used from a computer connected via USB to your android device. It can be used whilst the device is booted into Android or (if you have a custom recovery), it can be used in recovery too, unlike fastboot (yes, adb and fastboot are NOT the same thing) which can only be used in the bootloader.
adb can be used to push files to (or pull files from) your phone. It can also be used to execute many of the commands available in Linux terminals (Or Android terminal emulators) on the device itself. We're not here to cover all these commands however. We just want to cover the basics.
How to install adb and fastboot
adb and fastboot are very easy to install and can be installed on Windows, Linux and MAC computers. The Windows install can be a little bit more complicated than the other 2 and may need additional drivers installing too.
Windows.
There is a very handy tool that can install adb and fastboot in 15 seconds. It is recommended that you use this to install adb and fastboot. Please see the link immediately below for that tool:
ADB, Fastboot and Drivers - 15 seconds ADB Installer - Really quick and easy way to install adb and fastboot (by @Snoop05). Download links are at the bottom of post 1.
This tool asks if you want to install adb and fastboot (to which you should answer Y) and then creates c:\adb\adb.exe and c:\adb\fastboot.exe
It then asks if you want to install it system wide .. This is asking to install for all windows users. < 15 second installer needs updating to SDK 23, which is required for latest Android versions.
Download the latest SDK (adb and fastboot) versions here: https://developer.android.com/sdk/index.html (Scroll down to SDK tools only) then download the Windows *Installer*.
Open the installer and select "Platform-tools" and install the packages. This should create "C:\Program Files (x86)\Android\android-sdk\platform-tools"
Now we want to set this path as a Windows Environment variable PATH to make the executables work system wide:
right-click computer > properties > advanced > environment variables.
under system variables click "path" and click "edit"
at the end of the line, add the below:
Code:
;C:\Program Files (x86)\Android\android-sdk\platform-tools
Please note, the semi-colon ; is VERY important.
You may also need to install drivers.
Here is a link to the Google USB Driver: DOWNLOAD THIS
Code:
To install on Windows 7:
- Ensure existing drivers are uninstalled first*
- Extract the zip to c:\adb (created earlier by the installer)
- Right-click "Computer" > Manage in windows and choose "Device Manager"
- Boot the Nexus 6 to the bootloader (Volume down + Power) and connect the USB Cable
- Watch for any new devices with exclamation marks appearing
- Right-Click the new device > Update driver software
- Choose the "browse" method and browse to c:\adb, find teh folder you extracted then follow the wizard to the end - using amd6 64 if you're on a 64 bit system and i386 if you're on a 32 bit system.
*To uninstall existing drivers, boot into Android and connect the USB cable. Monitor device manager for the device showing up. To uninstall the device, right-click it to uninstall it. At the prompt, ensure you also choose to delete the driver. Repeat this for bootloader and recovery.
Code:
To Install on Windows 8, you may need to additionally disable driver enforcement
- From the Metro Start Screen, open Settings (move your mouse to the bottom-right-corner of the screen and wait for the - -- pop-out bar to appear, then click the Gear icon).
- Click ‘More PC Settings’.
- Click ‘General’.
- Scroll down, and click ‘Restart now’ under ‘Advanced startup’.
- Wait a bit.
- Click ‘Troubleshoot’.
- Click ‘Advanced Options’
- Click ‘Windows Startup Settings’
- Click Restart.
Once that is done, your Windows computer is configured for adb and fastboot.
In device manager, the device should show up as below, depending whether you are booted into recovery or bootloader...
Recovery - Android Device > Google Nexus 4 ADB Interface
Bootloader - Android Device > Google Nexus 4 Bootloader Interface
If it shows as something different, either you have existing drivers in the way or something went wrong.
Linux and Mac
Here is a really simple tool to install adb and fastboot on the above OS. The only expectation is you know how to open and run a terminal command. Please see the link immediately below:
Nexus Tools 2.2 (Featured by XDA) - adb and fastboot installer for Linux and Mac (by @corbin052198)
Once you have installed adb and fastboot from the above link, you're ready to go.
How to test adb and fastboot work
As previously mentioned, adb and fastboot are both command line tools. That means you must run these tools from command prompt (cmd in Windows) or Terminal (Linux and Mac).
Remember earlier, I mentioned that fastboot can only be used in bootloader? and adb can only be used in Android (or custom recovery - lets cover that later)? We can use the command "fastboot devices" and "adb devices to see if we have adb and fastboot working correctly.
Lets try it.
Boot your phone into android
Connect it to your computer via USB
Open cmd (start > type "cmd" on Windows) or Terminal (Mac/ Linux
Type in the windows "adb devices" and press enter
Here is what we don't want to see:
Notice how there is nothing underneath where it says "List of attached devices" That means it cannot see any device
Here is what we DO want to see:
We can see that there is now a device listed.
OK lets test fastboot. Unplug the USB and turn off the phone. When it is off, hold down Volume down + power until you feel the vibrate. You will now be in the bootloader. Reconnect the USB cable.
In the same window (cmd or terminal) we're going to now type "fastboot devices".
Again, here is an example of what we don't and do want to see:
If in both modes, you can see your devices "Serial Number", then you know they are both working.
Please note that if you cannot get adb and fastboot to work "system wide", you can open the command prompt to the location of the adb and fastboot executables exist and try from there.
OK Gimme some useful fastboot commands please!
Here are some of the most useful fastboot commands you will come across. Fastboot is used mostly for flashing images to the devices partitions on the internal memory.
Code:
fastboot oem unlock
This unlocks your bootloader and allows you to flash a recovery to root. WARNING, this will wipe your device. Rooting the N6 is essentially unlocking the bootloader, flashing a recovery and then putting the SuperSU zip on your sdcard and flashing it via the recovery. This thread covers rooting: [HOW-TO] The Nexus 6 All-In-One Beginner's Guide by @xBeerdroiDx
Code:
fastboot flash recovery recovery.img
This will flash a recovery.img to the recovery partition. The command is broken down into "fastboot flash" (what to do) "recovery" (where to flash to) "recovery.img" what to flash there. In the terminal or command prompt, you cannot just type "recovery.img" though. It has to be the path to where the recovery image is. For example, if my recovery image is on my desktop, I would have to type:
Code:
fastboot flash recovery c:\users\rootsu\desktop\recovery.img
It is worth noting, that it IS case sensitive, meaning if your file is called Recovery.img, you must type the capital R...
Other things you would flash:
Code:
fastboot flash system system.img
fastboot flash boot boot.img
These will flash the system image (ROM) and boot image (kernel) as you would if you were returning to stock.
A full guide to returning to stock can be found here: [TUTORIAL][GUIDE][HOW TO] Flash Factory Images || Unroot || Relock bootloader by @Mr hOaX
You can also boot into a recovery.img without flashing it...
Code:
fastboot boot c:\users\rootsu\desktop\recovery.img
which is "fastboot boot" (what to do) "c:\users\rootsu\desktop\recovery.img" what to do it with. As you may have noticed, we did not define the recovery partition in this command, that's because we're not flashing it....
OK Gimme some useful adb commands please!
At the moment, we are going to assume you have a custom recovery and you have booted into recovery. The reason for this is using adb in recovery can be much simpler.
Here are some useful scenarios for using adb.
Backup your sdcard to your PC
Code:
adb shell
mount data
exit
adb pull data/media/0 c:\MyBackup
**Please note, some recoveries may "mount data" automatically on boot, so don't be disheartened if you get an error stating device or resource busy. This probably just means you can't mount what is already mounted**
/data/media/0 is the real location of /sdcard for your information. Also referred to as "The mount point". What we have done here is "adb pull" (what to do) "data/media/0" (what to move) "c:\MyBackup" (where to move it to)
Push a zip file from your PC to your sdcard (useful if you wiped your sdcard and rom)
Code:
adb shell
mount data
exit
adb push c:\rom.zip data/media/0
What we have done here is "adb push" (what to do) "c:\rom.zip" (what to move) "data/media/0" (where to move it to)
You can of course also use adb to push and pull files to and from /system too. You just need to:
Code:
adb shell
mount system
exit
I mentioned earlier that using custom recovery is much easier for adb than whilst booted into Android. You need to ensure you have a kernel that allows insecure adb before you do anything with system and data partitions. You also need to ensure that USB debugging has been enabled in developer options.
For example, to mount system to pull files whilst android is running you have to:
Code:
adb root
adb shell
mount -o rw,remount /dev/block/platform/msm_sdcc.1/by-name/system /system
...which is clearly a little bit more involved, so I recommend you use recovery for adb push and pull. You can find more detailed information on adb here: http://developer.android.com/tools/help/adb.html
A little more about using Windows command prompt
One thing to understand is that like Windows, command prompt (cmd.exe) works with directories (or folders if you like). The Linux and Mac terminals are the same, but most linux users, we expect you would already know this.
Here you will see I have downloaded a recovery image that I want to flash using fastboot.
As you can see, the recovery.img is located in C:\users\rootSU\Desktop
Usually when you open the command prompt from the start menu, or run command, the command prompt will default to your user location as seen below:
So lets try and fastboot flash recovery recovery.img...
It fails with a not-too-accurate error message. It has failed because you have not told it where the recovery image is. It assumes it is in the directory as listed in the prompt
So, how do we deal with this? Well, there are 3 ways.
1) We tell the command prompt where the recovery.img actully is in the command itself
Success! As you can see, we have told the command that the location for the file is Desktop\recovery.img
2) We can change the directory in command prompt to the directory where the file is. In this example, we change directory to "Desktop". The change directory command is "cd " or in this case "cd Desktop"
3) ...and possibly the simplest method. We hold shift whilst we right-click on the folder we want to change directory to, and directly open a command prompt there:
Another point to make with command prompt or terminals, is if you do a particular command, it is "pre-programmed" to "expect" a particular format of that command.
For example, we know that adb push as a command expects after it . This means the command is actually
Code:
adb push
BUT if you put something AFTER , for example -
Code:
adb push somethingelse
, it will assume that the "somethingelse" is a bad parameter, and the command will fail. It will probably display (or "print" which is the technical term in a terminal) a helpful guide of how the command should be used instead of trying to run the command which it does not understand.
You're probably wondering why I am telling you this. Well quite simply, it is a warning about folder names. Imagine you have c:\users\rootSU\My Documents as a folder. You assume the command is then
Code:
adb pull /data/media/0 c:\users\rootSU\My Documents
but it is not... There is a space in between My and Documents. What you have actually done is
Code:
adb pull Documents
because it uses a space to signify the end of a command or parameter. It is best to avoid using folders with spaces in them. Avoid as much as you can. In the event it is unavoidable (Although when is it ever>) then please surround the path with quotation marks,
Code:
adb pull /data/media/0 "c:\users\rootSU\My Documents"
so that way, it sees everything between the " " as a single parameter.
Myth Busters
Myth 1: You need USB debugging on to use adb and fastboot
If you cannot boot into Android, it doesn't matter. You DO NOT need USB Debugging turned on to use adb outside of android. USB Debugging is an Android ONLY setting. Fastboot obviously also does not need debugging either as this too is outside of Android
Myth 2: to adb push or fastboot flash files, they must be in the same folder as adb or fastboot executables. Sorry but this is rubbish. You can pass the full path of the image you're flashing or file you're pushing in the command and fastboot / adb can be called system wide if you've set them as an environment variable or used the 15 second installer
thanks(im out of thanks). but ill be back to leave one here!!!!!
simms22 said:
thanks(im out of thanks). but ill be back to leave one here!!!!!
Click to expand...
Click to collapse
No worries. Just putting it here for info. It's not a new work, just a slightly amended version of my N5 thread. No need for thanks
rootSU said:
No worries. Just putting it here for info. It's not a new work, just a slightly amended version of my N5 thread. No need for thanks
Click to expand...
Click to collapse
it was up in the n5 threads before, and was needed here. but its here now as well, so thank you
Good guide. Needs to be a sticky. In fact, I think every device general forum should have a sticky like this. Would have saved me a lot of grief back when....
Excellent update.
Very good to see. I'm sure lots of people will be sending noobs here for the basics.
Up to your usual helpful, good work I see.
rootSU said:
This tool asks if you want to install adb and fastboot (to which you should answer Y) and then creates c:\adb\adb.exe and c:\adb\fastboot.exe
It then asks if you want to install it system wide (to which again, you should answer Y)... This then allows you to type adb commands in the command prompt without having to open a particular directory first. You may or may not understand what I mean when I say that, but take it from me, its much more convenient and easier to use this way.
Click to expand...
Click to collapse
Y option = System-wide = install to "C:\adb" and add path for system variable - This mean you can use it by any account on your pc.
N option = Current user only = install to "C:\Users\[YOUR USERNAME]\adb" and add path for user only - Only user account used for installation can actually use it.
So if you say Y or N you will be still able to use it from any directory with cmd.
rootSU said:
It will also ask if you want to install device drivers. Actually, say N to this as we're going to cover that next, using the google USB drivers
Here is a link to the Google USB Driver: DOWNLOAD THIS
Click to expand...
Click to collapse
Drivers in my installer are the one from the link you posted here. I'm not using any modified drivers, just the one that come with SDK. And they are also digitally signed.
I hope you will fix these But still nice work, beginners should understand it :good:
Snoop05 said:
Y option = System-wide = install to "C:\adb" and add path for system variable - This mean you can use it by any account on your pc.
N option = Current user only = install to "C:\Users\[YOUR USERNAME]\adb" and add path for user only - Only user account used for installation can actually use it.
So if you say Y or N you will be still able to use it from any directory with cmd.
Drivers in my installer are the one from the link you posted here. I'm not using any modified drivers, just the one that come with SDK. And they are also digitally signed.
I hope you will fix these But still nice work, beginners should understand it :good:
Click to expand...
Click to collapse
Thanks for the info. I thought system wide meant it was putting it as a path environment variable. Reason I didmt use the drivers from your tool originally is (well I wrote this thread for N5 originally) they didnt work so had to install the universal naked driver. But if yours are the same as the ones linked, I can update that.
rootSU said:
Thanks for the info. I thought system wide meant it was putting it as a path environment variable. Reason I didmt use the drivers from your tool originally is (well I wrote this thread for N5 originally) they didnt work so had to install the universal naked driver. But if yours are the same as the ones linked, I can update that.
Click to expand...
Click to collapse
Path is added in both cases.
Sooo I need a little help here. I followed the directions to unlock the bootloader and everything went good. I did the CF auto-root, and the phone booted back up as normal. Now, I was trying to flash the M preview, and all of a suddon now my phone isn't recognized in adb. You posted a pic of what we don't want to see when testing for adb, but you don't say how to fix it if we run into the problem. Any way to get it to recognize my phone again so I can get this build on?
papeshfoo said:
Sooo I need a little help here. I followed the directions to unlock the bootloader and everything went good. I did the CF auto-root, and the phone booted back up as normal. Now, I was trying to flash the M preview, and all of a suddon now my phone isn't recognized in adb. You posted a pic of what we don't want to see when testing for adb, but you don't say how to fix it if we run into the problem. Any way to get it to recognize my phone again so I can get this build on?
Click to expand...
Click to collapse
Can you be very specific with your issue please?
papeshfoo said:
Sooo I need a little help here. I followed the directions to unlock the bootloader and everything went good. I did the CF auto-root, and the phone booted back up as normal. Now, I was trying to flash the M preview, and all of a suddon now my phone isn't recognized in adb. You posted a pic of what we don't want to see when testing for adb, but you don't say how to fix it if we run into the problem. Any way to get it to recognize my phone again so I can get this build on?
Click to expand...
Click to collapse
Android M no like root, you'll either have to live with stock or wait for chainfire to do his thing.
This all worked well until I had to find my device in the cmd prompt. It listed no devices when I typed in "ADB Devices". The issue I found was with the ADB Interface Driver. I uninstalled it and reinstalled it thinking it might've been a driver issue, but it still wouldn't work. I tried the "Uninstall driver" then "scan for hardware changes" but that didn't work. Finally I found the universal ADB driver and tried using that. STILL nothing. I figured that, because I don't have my device's driver installed, it might've been that, so I tried to DL it and yet again, nothing. I have a Kyocera Hydro Life, if that helps. Also, I tried looking through the "update driver manually" in order to update the driver software by looking through the different ADB interfaces that it had but my Kyocera driver wasn't there. Is it supposed to be there or do I just use one of the ones provided?
I checked my programs and apps and it says that the Kyocera usb driver was installed. Did I do something wrong?
ScottyChaos said:
This all worked well until I had to find my device in the cmd prompt. It listed no devices when I typed in "ADB Devices". The issue I found was with the ADB Interface Driver. I uninstalled it and reinstalled it thinking it might've been a driver issue, but it still wouldn't work. I tried the "Uninstall driver" then "scan for hardware changes" but that didn't work. Finally I found the universal ADB driver and tried using that. STILL nothing. I figured that, because I don't have my device's driver installed, it might've been that, so I tried to DL it and yet again, nothing. I have a Kyocera Hydro Life, if that helps. Also, I tried looking through the "update driver manually" in order to update the driver software by looking through the different ADB interfaces that it had but my Kyocera driver wasn't there. Is it supposed to be there or do I just use one of the ones provided?
I checked my programs and apps and it says that the Kyocera usb driver was installed. Did I do something wrong?
Click to expand...
Click to collapse
Try a different USB port. If that doesn't work try a different USB cable. If that also doesn't work, you could try disabling driver signature checking for Windows.
If those don't work, try this thread > http://forum.xda-developers.com/showthread.php?t=1583801
cam30era said:
Try a different USB port. If that doesn't work try a different USB cable. If that also doesn't work, you could try disabling driver signature checking for Windows.
If those don't work, try this thread > http://forum.xda-developers.com/showthread.php?t=1583801
Click to expand...
Click to collapse
EDIT: I also forgot to mention that the error code that came up while I was in the dev manager was compatibility error code (28) when I clicked on "Device ADB interface".
ScottyChaos said:
EDIT: I also forgot to mention that the error code that came up while I was in the dev manager was compatibility error code (28) when I clicked on "Device ADB interface".
Click to expand...
Click to collapse
Error 28 means drivers not installed. Try the driver help thread that I linked above.
---------- Post added at 12:33 PM ---------- Previous post was at 12:04 PM ----------
cam30era said:
Error 28 means drivers not installed. Try the driver help thread that I linked above.
Click to expand...
Click to collapse
@ScottyChaos,
Just a fundamental question: I assume you have enabled "Developer Options" in Settings, and then checked "enable USB debugging"?
---------- Post added at 12:39 PM ---------- Previous post was at 12:33 PM ----------
[/COLOR @ScottyChaos,
Here is a thread that you might find interesting > http://forum.xda-developers.com/android/help/metro-pcs-kyocera-hydro-life-rooted-t2870678
Windows 10 device driver management is even more locked down then windows 8. I got two of the three drivers loaded but when going into adb mode on the phone through recovery it just disappeared out of the device manager. I had to unplug and plug in while in that mode to trigger a unloaded driver in the device manager. Once there I had to force the adb driver manually with the nasty windows driver warning and all. Once I did that I could see the device in adb mode and sideload my marshmallow OTA. woot!
I decided to drop a thanks bomb...
ADB is good.
But that fastboot.
Seriously, its ONE command. OK, a few different arguments to use.... But it is so easy, and so powerful. People are afraid to mess up on command line, but its actually way harder to type the wrong thing out then to click the wrong thing.
LEARN IT. Forget your toolkit.
You can fix almost anything, Its not too hard for you. It may be new... YOU CAN DO IT.
Also, I have to say it... Its not going to help anyone, but it will keep me from punching something. ADB and Fastboot... Not the same. You don't ADB a new system image....