I'm trying to connect my Meizu 5 PRO to the MTK Droid Tool 'coz I need to make a scatter file for flushing
the phone with international ROM. It runs the Chinese one atm.
The bar says "The device isn't revealed. Connect or reconnect the cable."
I did reconnect the cable and PDANet says the phone is connected. ADB is installed and USB debugging mode is on.
I tried to upload a screenshot but the site isn't allowing me to do that.
What should I do ?
Related
Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!
check to be sure USB SYNC driver installed correctly and also try a different usb cable.
I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?
exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.
Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?
well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.
Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?
since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)
I have a Lumia 520 (RM-915 version) 520 with windows 8.1 Developer Preview. Cyan Lumia wanted to install update so I used the software recovery tool for downloading Nokia firmware version 3058.50000.1425.0001. Installation began and showed an error of 1%. An option to recover appeared and tried but could not. Now the phone is bricked and when connected to the PC, shown as QHSUSB_DLOAD device. In Nokia Care Suite PST shown as USB: The product in flash mode selection data packets failed and reading product codes no error. When I select Open Product, select the device and select the data packet, which tells me hold Down + Power button until it vibrates and then retry. When I try no vibration could only see that the USB is disconnected and reconnected. Is there no way to recover it at home using my pc and usb cable?
use the following programs: nokia care suite, nokia software recovery tools, lumia software recovery tools, windows phone recovery tools
I leave you with this hope your help as possible to please
regards!!!!! :crying::crying::crying::crying:
Crispyn said:
I have a Lumia 520 (RM-915 version) 520 with windows 8.1 Developer Preview. Cyan Lumia wanted to install update so I used the software recovery tool for downloading Nokia firmware version 3058.50000.1425.0001. Installation began and showed an error of 1%. An option to recover appeared and tried but could not. Now the phone is bricked and when connected to the PC, shown as QHSUSB_DLOAD device. In Nokia Care Suite PST shown as USB: The product in flash mode selection data packets failed and reading product codes no error. When I select Open Product, select the device and select the data packet, which tells me hold Down + Power button until it vibrates and then retry. When I try no vibration could only see that the USB is disconnected and reconnected. Is there no way to recover it at home using my pc and usb cable?
use the following programs: nokia care suite, nokia software recovery tools, lumia software recovery tools, windows phone recovery tools
I leave you with this hope your help as possible to please
regards!!!!! :crying::crying::crying::crying:
Click to expand...
Click to collapse
using USB Cable no , maybe if anyone find or crack Best Box infinity last version you can unbrick by usb
else , you have to use a box like riff or JTAG
Hi, i am Damian, btw. im total begginer in case smartphone manage and i dont know english very well, so please, be forgiving.
Today i tried to unlock bootloader on my Meizu m2 Note M571H. I was using this tutorial:
I found a problem with the first step: turn off the smartphone and connect to your pc.
When i turned of my device, and connected by usb with pc, then my phone started charging, i heard the windows's sound of connecting device and just after sound of disconnecting. The Flash Tool didnt found my meizu m2 note and nothing happend. I tried to download newer version of flash tool, download the scatter from other website, update a meizu drivers (they were the lastest), restart phone and pc, use other usb port, turn on debbuging mode, root my device etc. I still didnt resolve my problem. Have you any idea what can i do?
And 1 more time - please, be forgiving because of my english.
I would be very thankfull if will you help me.
@edit
I was installing drivers for wrong com Im an idiot.
Hey I'm facing the same problem.. Can you please help me ?
I am facing the same issue, could be the rom version, I am in 6.xx
or Windows 10.
No COM is appearing for me...
No idea how to solve it though, sorry
First of all you have to download mtk vcom drivers,so when you connect your phone,it will appear in sp Flash tool.Then you have to download unlock tools from web.There you have all that is needed for unlocking the bootloader
Almost a month ago, my phone ran out of battery so I charged it. When I got back, there was a warning sign and below it said: "the system has been destroyed"
I tried everything I could to flash it, included the official Xiaomi flash tool, but the problem isn't the method itself, but the phone, which it's not being recognized by my pc at all.
When I connect it (In fastboot mode), a notification shows up saying: "The USB device is not recognized", I tried commands, updating the drives, cleaning up the USB port, another USB cable, but nothing worked.
Does anyone know any possible solution for this? Thanks in advance : D
faulty usb cable may be the reason and try edl mode
MrHarveen said:
faulty usb cable may be the reason and try edl mode
Click to expand...
Click to collapse
I have already tried with other cables (and all of them are working for everything except this, so it's the device's fault), and edl mode can only be activated with a computer, so i guess i'll keep trying
Drivers must have been installed multiple times.Delete them and reinstall.
Cheers.
Same problem bro
Hi!
There is a way to enable EDL mode without computer but you'll have to open your phone.
Once opened, you must short two specific test points while connecting USB.
That's how I got out of a bootloop with a locked bootloader.
For the procedure just search for "edl test point mi a1", there are many videos.
I have installed all the drivers needed and my devices have been connected, but after I enter Fastboot mode and I plug the computer and then open the mi unlock tool, my devices are immediately not detected. is there a solution to this problem?
Test an other usb port not 3.0.
You can see here
https://forum.xda-developers.com/redmi-note-7/help/unable-to-unlock-bootloader-t4046611