Related
after mailing SAMSUNG by Mr.Alzubair
from ce4arab website
about the Death screen
this is the answer :
-----
Dear Alzubair ,
Thank you for contacting Samsung Electronics.
Reference number:2104286715
Regarding your case, kindly note that the image you have displayed on
the screen of your phone, indicates that the device has entered the
Recovery Mode. The reason this happened, is because you have tried to
update the device’s Firmware, which isn’t actually released yet, and
that’s the reason why the Software crashed as well.
In order to get out of the Recovery Mode, please follow the steps below:
Recovery Process
1.Remove the battery and reinstall it. Power On your Phone
- Phone display “Connection picture for Phone to PC”
2. Recovery Mode in Kies
If upgrade failed in upgrade step, you can see next Pop-Up
- Select "Yes”
Firmware Upgrade program progress to recovery mode.
3. Select "Recovery" button.
4. Read the caution and check “all information has been verified”
- After this, it’s same with Firmware update Process
5. Click “Next”
- Firmwareversion display
- Firmware file is downloaded to PC
6. Firmware update
- After Firmware downloaded, Click “Next”
- Firmware update start
Caution
- Never disconnect or turn off the
device in thisstep
- If so, recover the phone refer to
recovery section
7.Complete
- After Firmware update complete, the device reboot
automatically
- Click “Next” Button
To do this manually instead of using Kies, please click on the Power
button, the Volume down button and the middle button all together all at
the same time. The phone would flash for 2 times, and on the 3rd time,
please remove your hands fromthe phone, and it should boot up normally.
I hope this has been of some assistance to you. If you do have any
further queries, please do not hesitate to contact us quoting your 210-4286715
reference number.
Kind Regards,
Aya Smith
Samsung Electronics UK
Customer Communication Centre
Tel.: 0845 726 7864 (All calls charged at Local Rate)
Homepage: samsung.com
[Product] GT-I9000
The reason this happened, is because you have tried to
update the device’s Firmware, which isn’t actually released yet, and
that’s the reason why the Software crashed as well.
Click to expand...
Click to collapse
Bwahahahhaahahahahh!!
cheetah2k said:
Bwahahahhaahahahahh!!
Click to expand...
Click to collapse
LOL XD
at least they help me
I just tried it ( by the Manual way ) and it Works
so this works on the semi-bricked, no 3-button combo enabled phones ??
.. let's say, after a bad/failed bootloader flash ?
someone please confirm ?
later edit:
from what I understand after reading this, Kies can force any (Phone--!--PC) SGS into recovery and/or download mode?
if so, can we "extract" this feature and make it into a stand alone solution for half-bricked phones?
That's not a real black screen, I got one and my phone got the BSOD: No possibility to power on, no charging, nothing.
The "phone ! computer" is just a semi brick, get back to download mode and reflash with odin...
But thanks for the info indeed.
franklin01 said:
The "phone ! computer" is just a semi brick, get back to download mode and reflash with odin...
Click to expand...
Click to collapse
Some SGSs can't access download mode from that screen because of the proper bootloader that's missing. (3 button combo fix needed, not so safe)
wish samsung also adds a feature to kies that fixes the IMEI =D
franklin01 said:
That's not a real black screen, I got one and my phone got the BSOD: No possibility to power on, no charging, nothing.
The "phone ! computer" is just a semi brick, get back to download mode and reflash with odin...
But thanks for the info indeed.
Click to expand...
Click to collapse
2day i triad it two times and it works
but from what i understand same thing happened to me today ..
i did the 3 times flashing way :
BE SURE THAT YOU disconnect THE CABLE!!
To do this manually instead of using Kies, please click on the Power
button, the Volume down button and the middle button all together all at
the same time. The phone would flash for 2 times, and on the 3rd time,
please remove your hands fromthe phone, and it should boot up normally.
Then its work and downloading mode appear i installed an official Ver. by odin ( check on Re-Partition ) then it will work (work for me after the same thing that happened : No possibility to power on, no charging, nothing. )
Does this means that the phone has a secondary bootloader or what I dont get it, I already sent my phone to samsung so I cant try, I had my phone bricked stuck at a black screen after the S logo.
hang on... so it sounds like samsung is saying that phones that dont go into download mode straight away from vol-down, home and power need to keep holding the power button until the power cycles 2 times, then let go on the third?
i cant test it now because after i bricked my phone (black screen no power on or charge) i sent it back and i got a new motherboard with 3-button enabled... but this does make sense because when i had a 3-button disabled phone previously i did manage to get it into download mode from the phone-!-computer screen by trying different timings. it took a long time but eventually worked.
so it would seem if this is the case, that it is just a different boot loader and a different key combination to access download mode, but working nevertheless?
can someone test this?
Cant believe it, if the phone does has a secondary bootloader then it cannot be bricked forever.
Sent from my GT-I9000 using XDA App
stephengoo said:
Cant believe it, if the phone does has a secondary bootloader then it cannot be bricked forever.
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
We already knew it had a secondary boot-loader...
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Partitions
This is what is patched to hotfix the 3BR in disabled phones.
3 times flashing way wont work for me, and at Recovery in Kies i cant see my Device!
Absolutly no USB!!!!
Sorry Guys!
So this forced download mode can be possible...
This guy here tried hard to explain same thing:
http://forum.xda-developers.com/showthread.php?t=812933
do you think it will work with korean version galaxy s?
No-Exit said:
3. Select "Recovery" button.
4. Read the caution and check “all information has been verified”
- After this, it’s same with Firmware update Process
To do this manually instead of using Kies, please click on the Power
button, the Volume down button and the middle button all together all at
the same time. The phone would flash for 2 times, and on the 3rd time,
please remove your hands fromthe phone, and it should boot up normally.
[Product] GT-I9000
Click to expand...
Click to collapse
"all information has bee verified" means put phone in download mode and connect it to PC (can't do it without working 3 buttons combo).
"manually instead of using Kies" = same thing, doesn't work without 3 buttons combo.
This doesn't works if you didn't have 3 buttons combo enabled. I used heat trick instead and then patch aires P-SBL.
I sent my phone back because of this black screen of death. I could get into Download mode, and the other (vol-up) mode too, but no upgrading or changing firmwares worked to fix it. And Kies didn't see it, though Odin eventually did.
Wondering now if the Black Screen of Death was fixable after all, but then would Kies have to recognize it first?
I have a phone ! pc bricked phone right in front of me, I've tried this and a million other combinations, nothing works. I'm not being super pessimistic or anything it really doesn't work. I've left it with a phone repair store overnight and they couldn't fix it either. Im going to visit samsung/optus tomorrow.
edit:
I also want to point out that that message contains some horrible english supposedly from samsung UK
d47:
I am exactly in your shoes. Even with the overnight leave at a GSM repair booth-thingy. Im also considering handing it back to the retailer, but havent tried the heating up trick yet... Maybe its worth a try ?
ok so here is what happened i have a stock US retail wifi only 16gb tab no clockwork recovery or none of that , im kind of a noob when it comes to that stuff, so today i received the update cool i downloaded it but it didn't install the first time for some reason. The it said a previous update was sucessfully downloaded but did not install do i wish to instal so i clicked yest and it said tab is about to reboot, clicked ok and it took me to this black and grey screen like the boot screen only with a loadbar and it zoomed to 100 percent. then i got the original samsung galaxy boot logo and the noise but no animation then the screen goes to this nasty screen with alot of colorful lines and dots everywhere and i cant see anything looks terrible.
Heres what i can do i can go into the bootloader by pressing power and volume. and i already tried to do a restore/wipe but didnt help, i can also plug it in to the computer and use the sd card and put and remove files from tab. im wondering if i can somehow get the update put it in the tab and install from there and see if it works or if i can get stock honeycomb and try to see if that works because they guy at samsung was clueless he didnt get the fact that i cant use the OS and said i need to get it serviced when i know its a software problem.
exact same thing happened to me! keep me posted
I've just got absolutely the same problem. I have a stock wifi 32gb version.
If you can get to your bootloader and sdcard still then why don't you just install CWM and try flashing the stock 3.1 OTA?
All the files you need and instructions are here: http://forum.xda-developers.com/showthread.php?t=1171089
Once you're done flash the stock recovery back and try the update again, or just wait for one of the devs to release a flashable zip.
sorry if im mistaken but dont i need to be able to use the tab and install something from the market place to be able to install CWM thats what im getting from what i read?
I can't even get my bootloader. Holy f**k am I pissed. Does anyone have any ideas??
Ok. So I installed the Samsung Kies software. It recognizes the device and shows that the update is available. However, it says that the battery should be fully charged. So now I am waiting for the full charge to proceed.
Hope the Kies helps.
I'll try that too. ahh
tonyurquiza said:
sorry if im mistaken but dont i need to be able to use the tab and install something from the market place to be able to install CWM thats what im getting from what i read?
Click to expand...
Click to collapse
No.
Go to the thread I linked, download the files, watch the youtube video.
1. Install the GT-p7510_USB_Driver if you haven't already
2. Start Odin - untick the auto reboot option
3. Click PDA and choose recovery-cwm_4.0.0.4-sam-tab-10.1.tar.md5
4. Power up your tab and get it into download mode (power down + vol down, then vol up)
5. connect the tab to your PC, one of the boxes in odin should highlight yellow and say com 4 or whatever.
6. press start and it'll flash CWM to your tab
7. wait till it's done, it should only take a few seconds and the boxes will turn green.
8. power down your tab and unplug it from your pc
9. boot into CWM, (power down + vol down, vol down to select CWM, vol up to enter.
10. flash hc-3.1_ota-full_sam_tab_10.1.zip
11. do a factory wipe in CWM and wipe davlik just to be safe
12. reboot, and hopefully you'll be back to stock 3.1
From here you can do whatever you want.
Connect it to a PC and there's a firmware recovery on KIES. Hope that works!
Sent from my GT-P7510 using XDA Premium App
lordwinkevin said:
there's a firmware recovery on KIES
Click to expand...
Click to collapse
it didn't work for me. There were no devices in the list to recover.
I'm going to try it once my kies is finished updating. I really hope this works.
haha well first and formost i want to thank everyone for thier input. I did alot of searching online i tried KIES samsung tech support was useless. So i found the instructions on how to put clockwork on a locked bootloader got it on there and flashes the stock rom and it worked my tab is now back! only problem now is i tried to update again and only go the minor update and it doesnt find the big one lol but cant complain ill just wait lol thanks again. and to others who had the same problem dont deal with KIES to recover its useless unless you were using the program to update. I suggest getting CWM and flashing stock since thats what worked for me?
tonyurquiza said:
haha well first and formost i want to thank everyone for thier input. I did alot of searching online i tried KIES samsung tech support was useless. So i found the instructions on how to put clockwork on a locked bootloader got it on there and flashes the stock rom and it worked my tab is now back! only problem now is i tried to update again and only go the minor update and it doesnt find the big one lol but cant complain ill just wait lol thanks again. and to others who had the same problem dont deal with KIES to recover its useless unless you were using the program to update. I suggest getting CWM and flashing stock since thats what worked for me?
Click to expand...
Click to collapse
Glad to hear it worked.
Since you now have CWM, just download the flashable zip from here: http://forum.xda-developers.com/showthread.php?t=1198921
Make sure you do a factory reset in CWM after you flash this, otherwise you'll bootloop.
hoodoomagic said:
No.
Go to the thread I linked, download the files, watch the youtube video.
1. Install the GT-p7510_USB_Driver if you haven't already
2. Start Odin - untick the auto reboot option
3. Click PDA and choose recovery-cwm_4.0.0.4-sam-tab-10.1.tar.md5
4. Power up your tab and get it into download mode (power down + vol down, then vol up)
5. connect the tab to your PC, one of the boxes in odin should highlight yellow and say com 4 or whatever.
6. press start and it'll flash CWM to your tab
7. wait till it's done, it should only take a few seconds and the boxes will turn green.
8. power down your tab and unplug it from your pc
9. boot into CWM, (power down + vol down, vol down to select CWM, vol up to enter.
10. flash hc-3.1_ota-full_sam_tab_10.1.zip
11. do a factory wipe in CWM and wipe davlik just to be safe
12. reboot, and hopefully you'll be back to stock 3.1
From here you can do whatever you want.
Click to expand...
Click to collapse
How would i get hc-3.1_ota-full_sam_tab_10.1.zip on my tab to flash via CWM if I can't get the tab to boot?
tonyurquiza said:
ok so here is what happened i have a stock US retail wifi only 16gb tab no clockwork recovery or none of that , im kind of a noob when it comes to that stuff, so today i received the update cool i downloaded it but it didn't install the first time for some reason. The it said a previous update was sucessfully downloaded but did not install do i wish to instal so i clicked yest and it said tab is about to reboot, clicked ok and it took me to this black and grey screen like the boot screen only with a loadbar and it zoomed to 100 percent. then i got the original samsung galaxy boot logo and the noise but no animation then the screen goes to this nasty screen with alot of colorful lines and dots everywhere and i cant see anything looks terrible.
Heres what i can do i can go into the bootloader by pressing power and volume. and i already tried to do a restore/wipe but didnt help, i can also plug it in to the computer and use the sd card and put and remove files from tab. im wondering if i can somehow get the update put it in the tab and install from there and see if it works or if i can get stock honeycomb and try to see if that works because they guy at samsung was clueless he didnt get the fact that i cant use the OS and said i need to get it serviced when i know its a software problem.
Click to expand...
Click to collapse
Mine did exactly this too, by the way....
I would go this way:
http://forum.xda-developers.com/showthread.php?t=1167250
/Doc
* deleted *
Thank you DocRambone, flashing that via Odin got me up and running.
Then I flashed CWM as per earlier post and then flashed the Stock UEKMB + root ROM and I guess I am good to go.
Ok guys. This is my report. I used the Kies to update. The firmware was updated successfully and now the tablet works perfectly!
So this is easier and less painful method than using CWM described above =)) (but thanks to hoodoomagic for the description anyway)
Hope this will help somebody.
I somehow lost the backup of my premangostate after updating to mango. I'm having issues with my device overheating and I need to mail it in to AT&T. But doesn't the Mango beta technically void your warranty? If it does, I need to revert to premango in order to send it in... what should I do? I've tried everything. I downloaded a ROM but I don't know how to use it! HELP!!
eaglesfreak53 said:
I somehow lost the backup of my premangostate after updating to mango. I'm having issues with my device overheating and I need to mail it in to AT&T. But doesn't the Mango beta technically void your warranty? If it does, I need to revert to premango in order to send it in... what should I do? I've tried everything. I downloaded a ROM but I don't know how to use it! HELP!!
Click to expand...
Click to collapse
It does void it. Flash UCJK2 ROM from here. Just tell them you didn't update.
EnderPsp said:
It does void it. Flash UCJK2 ROM from here. Just tell them you didn't update.
Click to expand...
Click to collapse
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
eaglesfreak53 said:
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
Click to expand...
Click to collapse
There isn't one for Focus but if you follow the step by step guide for Omnia 7 with the Focus Rom, you should be okay as it's exactly the same. Just use the Focus UCJK2 Rom instead of the Omnia7 one.
Here's the short version:
You will not need the "Samsung WP7 Flash Program" as it is included in the ROM (Samsung-i917-Focus-firmware-UCJK2-ATT-USA.exe).
Install Samsung Mobile USB Drivers v5.2
Put the phone in download mode. Make sure battery is at least 80% when you do.
Turn off the phone
Turn on the phone, holding down the Power + Volume UP + Camera buttons simultaneously.
When the phone turns on, release the power button.
A yellow triangle with an exclamation mark and a "download mode” message should appear.
(there are 2 ways to get out of this mode: flash a rom or remove the battery).
1. Copy "Samsung-i917-Focus-firmware-UCJK2-ATT-USA.exe" in a new folder and run it (Install). After running you will see these files:
signed_CSC_Cetus_ATT_i917ATTJK2.csc
signed_eboot_Cetus_ATT.eb0
signed_pda_Cetus_ATT.nb0
signed_phone_Cetus_ATT.bin
WP7 Downloader Ver 7.21 for All Device (Publish version).exe
WP7_Downloader_Ver_7.05_for_Retail_Device_(Product_Force_Select_MD5_X).exe
The fhash program you need to run is
WP7_Downloader_Ver_7.05_for_Retail_Device_(Product_Force_Select_MD5_X).exe
2. Run it and load in it the files in this folder (click Phone, Eboot, PDA, CSC)
3. If the port isn't green, disconnect the phone from USB and reconnect.
You should be good to go with all this.
eaglesfreak53 said:
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
Click to expand...
Click to collapse
I'll be reflashing my Rogers Samsung Focus yet again since I've been trying to change MMS settings so it will work with FIDO. Anyway, I'll be reflashing this weekend. PM me if you want some walk through steps.
[Q]Restoring backup after flashing rom
Hi,
I have a At&t samsung focus running 8107 and phone's power button started acting weird. If i press it nothing happen at first, then the slide down to power off appear. I would press back but it would shut off anyways. It wouldn't reboot right and usually took about 20 tries to boot it. I have two backups saved one mango beta and one for current version. The problem got worse (wouldn't boot at all unless on usb power) so i restored it to my current version backup. Everything worked but after a week the problem came back and the phone was dead. I decided to flash it to factory rom (had problems getting it to boot to rebuild) but I eventually got it to boot. The power button still did nothing. I updated it back to 8107 and tried to restore to my backup. I keep getting error code 801812E0. My question is do you have to use the same update path to restore a backup? I had the mango beta, refresh, then cleanup to get to 7720 Mango build. The second time around I used official update path. Do you think this is hardware related?
Thanks in advance
From your description, it sounds like your power button is getting stuck in the pressed position. "Always Pressed". Occasionally, when messing with it, it will release. Also, when plugged in, that forces it to start up.
Try cleaning around the button, or remove any cases/screen protectors that might be sticking it down. If that does not work, you might need to take apart to clean or replace the button. Only attempt if you are comfortable with that type of job, otherwise, send in for repair.
Thanks for the quick response. I will try that.
Also would the power button being stuck affect the hard reset menu and download mode? I can still access download mode but the hard reset menu disappears after about 10 seconds. The only way I can reboot the phone is to plug into USB power via computer and touch the metal springs where the battery connects with a tweezers.
xyzyzyxx99 said:
Also would the power button being stuck affect the hard reset menu and download mode? I can still access download mode but the hard reset menu disappears after about 10 seconds.
Click to expand...
Click to collapse
Yes. If you hold the power button in Any mode, it forces a shutdown after a few seconds.
Took the phone apart and cleaned around the button. Still won't boot, is it possible the phone's drivers to communicate with the power button are bad? And any idea why my backups failed to restore after flashing the rom?
xyzyzyxx99 said:
Took the phone apart and cleaned around the button. Still won't boot, is it possible the phone's drivers to communicate with the power button are bad? And any idea why my backups failed to restore after flashing the rom?
Click to expand...
Click to collapse
I think this has gotten off topic from the original thread. I'll send you a private message, and we can continue there. I've been around a while, so I might get into trouble keeping it going here, since I should know better.
Does anyone have a working link to download the Samsung Focus USB drivers?
All the multiupload links are down and i am stuck with a bricked phone.
Mirror or alternate link appreciated..
Thanks
NilayS said:
Does anyone have a working link to download the Samsung Focus USB drivers?
All the multiupload links are down and i am stuck with a bricked phone.
Mirror or alternate link appreciated..
Thanks
Click to expand...
Click to collapse
Download Samsung drivers from here.
Can I get the long version of flashing a Focus I917. Yes noob, if by chance there are some pics would be helpful also! Thanks in advance!
SteelLife said:
Can I get the long version of flashing a Focus I917. Yes noob, if by chance there are some pics would be helpful also! Thanks in advance!
Click to expand...
Click to collapse
Follow this post.
Hi, i got a problem with my 10:1 tab. Today i tried to install honeycomb rom using clockworkmod recovery and after the installation and rooting my tab there was a question should flash boot be fixed because the new one will replace other without going back so new flash and root from honeycomb could take it place and i said no to fixing it, second after my tab went off black and it not reacting to anything including trying to power on and get into recovery mode and i tried to push all the buttons and nothing works. Odin doesnt recognize the tab and if i plug it to charger or pc there is no response. The only thing i realized is i heard a plug in usb sound when i connect tab to pc and try to pull the power on button for like 5 seconds i hear plug in and second later plug out usb sound. What can i do to make it works again? I cannot give it to guaranty and all i can do is by myself
Send it to Samsung for a repair.
i cant, i have no guarantee all i can do is by myself, what can i do?
Did you try to hold power button a little longer ? Like 10 or 30sec. This works for some devices
Sent from my GT-P3110 using xda premium
Pull back cover off (use google to figure out how to do so), unplug battery for a few seconds. Plug battery back in. Press and hold power + vol down to try to get into ODIN.
There is no honeycomb rom for these tabs. What did you try to install? Link me.
Holding power button gives nothing, i tried ever combination for a couple minutes and not working. I tried to remove battery yesterday but it was connected via cables and there was no way to remove it without cutting out cables as far as i seen, if anyone can know how i can remove battery then let mw know because i can't find anything ever the internet. I downloaded HoneyVillain_1.2 from here http://forum.xda-developers.com/showthread.php?t=1138115. I tried to plug tab to charger today but after 10 hours it didn't worked at all, still got black screen with no reaction to buttons ;/
Hello
bad news - I killed my P5100 2 months ago and I can't repair it. I have same problem - I can hear plug on / plug off sound in Windows. But i have installed drivers and found that this is OMAP4430 device was connected/disconnected each time. And I can't do anything with my Tab.
I have took my Tab to official Samsung service and I've received answer that it is not repairable - only full replacement of internal board possible, and it costs 300$.
And I have tried to unofficial services and they tells me what my problem. Bootloader was corrupted and device can't start. So it is impossible to repair bootloader because it is protected in Galaxy Tab 2 and they proposed me to replace internal flash memory chip.
So I have dead Tab and wait for ability to programmatically repair my Tab
You can see my thread here http://forum.xda-developers.com/showthread.php?t=1908949, maybe it will be helpful for you
FrostX26 said:
Holding power button gives nothing, i tried ever combination for a couple minutes and not working. I tried to remove battery yesterday but it was connected via cables and there was no way to remove it without cutting out cables as far as i seen, if anyone can know how i can remove battery then let mw know because i can't find anything ever the internet. I downloaded HoneyVillain_1.2 from here http://forum.xda-developers.com/showthread.php?t=1138115. I tried to plug tab to charger today but after 10 hours it didn't worked at all, still got black screen with no reaction to buttons ;/
Click to expand...
Click to collapse
I honestly believe that the Rom you downloaded is for the acer ionica!
See xda has created separate forums for each phone because you can't use one phones rom for another! Yet you flashed that!
There s nothing you can do other than sending your phone for repair!
Sent from my GT-P3100 using Tapatalk 2
Ok so i installed wrong rom for my tab right? Is there something i can do to repair it by myself?
FrostX26 said:
Ok so i installed wrong rom for my tab right? Is there something i can do to repair it by myself?
Click to expand...
Click to collapse
No. Its a paper weight now and you could have prevented this by reading.
If you can't get it into Download Mode, then the only options are to send it to Samsung to fix it, or find some loose papers.
Hey guys, thanks for the answers so far I would like to know if every type of tablet brick can be unbricked? I mean if there is no brick that couldn't be unbricked by using cables and garage methods
FrostX26 said:
Hey guys, thanks for the answers so far I would like to know if every type of tablet brick can be unbricked? I mean if there is no brick that couldn't be unbricked by using cables and garage methods
Click to expand...
Click to collapse
http://www.jtagbox.com/jtag-news/ri...tab-2-101-unbrick-dead-boot-repair-supported/
I don't know how much support you'll get to follow this method but if nothing else will work it's worth a try.
As far as this tablet being unbrickable, that's only true if you don't intentionally flash something that was made for a completely different tablet...
Sent from my GT-P5110 using XDA Premium HD app
Well that's the point, I flashed with rom made for different tablet and it's dead now My question was if any brick could be repaired if i'll give it to someone with all the right tools to resurrect it, or there are certain bricks that can't be repaired no matter what tools and skills the person who attempt it have?
FrostX26 said:
Well that's the point, I flashed with rom made for different tablet and it's dead now My question was if any brick could be repaired if i'll give it to someone with all the right tools to resurrect it, or there are certain bricks that can't be repaired no matter what tools and skills the person who attempt it have?
Click to expand...
Click to collapse
Check my post again for the link as that's the only method that shows up on Google search for this tab.
does odin recognize your tablet?
Is it a tab 2. In your op it just said tab 10:1. Not tab 2. Just making sure as this is the tab 2
sent from MY BAD A$$ ET4G
I might be able to help u
Alright i had the problem recently and heres what i did to fix it If you can get into download mode ur all good from there. To get into download mode hold the power button and up on the volume rocker, if u get a message saying flashing roms is dangerous blah blah blah then press down on the volume rocker to enter download mode. Odin will recognize it if its in download mode, also what model is ur galaxy tab? Also if its a 10 inch model GT5113 i have the stock rom file for it so i could send it to u
Some helpful Info
Maybe you should have said yes? because after all you can't be too carefull , maybe there was something wrong with the rom. If the system asks you if you want to fix ALWAYS say YES. You should have said yes. Why did you say no ?! all right now to the fixing part. PLEASE NOTE I'M NOT AN EXPERT IN ROOTING BUT I'LL GIVE IT A GO. I think that if you can, then power it up and press the VOLUME UP key while holding the power button. From the menu choose recovery and factory reset your device. If it's possible reset rom to default. It should work if not then Post a reply saying not and I'll see what else can be found. Hold on tight for now!There is a Optional thing you can do if the above doesn't work: that is, if possible, you can un-root your tablet with an app from the market. If all of the above is impossible to do, and you cant even power your tab on, it's as useful as a brick, a black screen. Then I'm afraid it's a hard brick fopr you, boyo.
---------- Post added at 03:48 PM ---------- Previous post was at 03:41 PM ----------
FrostX26 said:
Hey guys, thanks for the answers so far I would like to know if every type of tablet brick can be unbricked? I mean if there is no brick that couldn't be unbricked by using cables and garage methods
Click to expand...
Click to collapse
Sorry for my previous post, didn't read the whole forum! Stupid me! ok now there are only two types of brick. Soft brick and hard brick. Soft brick can be fixed, Hard brick - Not quite. And as you said, you flashed a rom for a different tab, maybe thats a compatibility issue. If you want a new os, honeycomb to be exact. You can always upgrade, just search 'honeycomb upgrade'.
Hi. Browsed for ages and always come here for answers.
Here's my problem.
2x S8s. SM-950f.
Updated to most recent software through software update. Both phones were glitchy and crashing and just generally irritating after.
Factory data reset etc. This did not resolve the problems, also led to one of them having issues with FRP (annoying)
Used Odin to try and flash the latest firmware (from sammobile, UK BTU) after flashing both, they reset and powered on. Got stuck at the S8 screen.
Restarted then both were at the "an error occurred during update" screen.
Managed to get back to download screen. Re checked the software and model numbers, even that the bootloader was the correct version etc. All was fine.
Connected to Odin, shows that it is connected, but nothing happens when clicking start.
Now after attempting that, both phones will not power on.
(One will when placed on the wireless charger, but just sticks at S8 screen) and download mode or reset screen can not be accessed. So, not exactly happy. And totally out of ideas
Any suggestions, beyond taking it to a shop to see if anyone can help.
yes .....dont tuch the phones for 24 hours let the battery die ...it will...connect to pc and then try download mode....u may need to press combination for like 1 minute to get to download mode....flash twrp reboot directly into it when odin says successfully .....wipe system data ....dont turn on phone download any custom rom flash and enjoy.....it will trip knox but worth than getting a new board....
Okay, will give that a try.
TWRP?
TWRP install
https://dl.twrp.me/dreamlte/twrp-3.2.3-0-dreamlte.img.tar.html: Download link for twrp SM-G950F (dreamlte)
Just said, wait until your device powers off due battery insufficience. Plug cable and hold at the same moment vol(down)+bixby+power. Then press vol(up) at the warning screen to proceed to odin mode. Let it charging a while like 1 h. Then unplug it and plug it to your pc. In Odin select ap the previous downloaded file. Take your mobile in your hand. With one hand, prepare your fingers to vol(up)+bixby and with the other hand start the flashibg process. Be careful, and take your hand directly from the mouse if you clicked start in odin, and position your one finger to power button, but dont click. If odin start pass, press immidiately the buttons (vol(up)+bixby+power) and let it to start into recovery. If you arrived to recovery, reply to us if not search for help!!!
Good luck
memreb
Still trying to get them on. Powered on to download mode but only for a couple of seconds and switched off again.
Can't get them to power on. Buggered
simonboyle said:
Still trying to get them on. Powered on to download mode but only for a couple of seconds and switched off again.
Click to expand...
Click to collapse
i have the same issue with my s8 but when i boot in download mode the screen goes black but if i press volupe up it connect to odin with black screen you shoud give it a try
Will try that
Okay, downloaded TWRP, can get phone calls nected to Odin but when I extract TWRP it doesn't give a valid file type.
Am I being dumb.
No files appear that Odin will recognise.
Also just shows as "recovery" no .tar or anything
Ignore above. Corrupted download.
Sorted.
Now when flashing TWRP is gets to a fail due to
"Complete (write) fail
Hi you should try flashing official firmware
itac47 said:
Hi you should try flashing official firmware
Click to expand...
Click to collapse
The point of the thread us that I am.unable to do that.
So kinda useless post buddy.
Read the OP.
Anyone want two bootlooped S8s? Hahahaha
simonboyle said:
Anyone want two bootlooped S8s? Hahahaha
Click to expand...
Click to collapse
Not sure what stage your at and maybe some more useless ideas
1. Trying to flash twrp is kinda of useless if you can't get into your system need oem unlock for that.
2. Have you tried taking out Sim card and SD card and reboot.
3. If you can at least boot try smart switch as it has a emergency recovery option.
4. Trying rebooting in safe mode.
All been attempted