Related
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
kitsunisan said:
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
Click to expand...
Click to collapse
I cant fine one either but there are 2 screws in the battery compartment and it looks like the metal portion where the camera is may pop or peel off with a little force. My guess, try to remove metal portion where camera is, if it comes off and exposes screws remove those along with 2 in bat compartment then use tool to try and separate where bezel and rubber surround are. Just fumble it.
May I ask why your taking it apart?
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
kitsunisan said:
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
Click to expand...
Click to collapse
I don't think a phone exists that you dont have to pry, push, pull and force things to get them apart. There will ALWAYS be risk of breaking things when taking a phone apart. I would just deal with it and not open the phone. Plus, they usually have a way to tell if you've opened your phone so you will void your warranty.
There is a "void" sticker on one of the screws. If someone does open her up, check to see if you could replace the speaker with a better one from another phone.
Please post questions in Q&A section.
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
dustrho said:
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
Click to expand...
Click to collapse
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
damn still no tear down i need one buttons jammed
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
pdxrealtor said:
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
Click to expand...
Click to collapse
I'm looking to buy someones Part "Power Ribbon Cable Assembly" (The part thats connected to the power button) *BE CAREFULLY" Everything has to be in Working order and not torn! Send me photos of the part I'm looking for and price. [email protected] Thanks!
dustrho said:
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
Click to expand...
Click to collapse
You must never have had a MT3G. These buttons are a dream compared to the creaky clickers in that dog.
I bought a refurbished phone on Craigslist and there are fingerprints on the inside of the glass (I don't know why I never saw them when I was inspecting). Would like to teardown guide so I can go clean those prints off.
Lil bit of thread necromancy here, but did anybody ever find a teardown? I'm thinking of ripping mine open due to my backlight issue ( http://forum.xda-developers.com/showthread.php?t=958033 ). I guess if nobody else has a teardown, I'll have to brave the waters and post my own, but going in blind is going to increase the risk of me killing the thing even worse than it already is
I'm also preparing to replace my digitizer. I came across a couple recent tear-down videos:
http://forum.xda-developers.com/showthread.php?t=961252
http://www.repairsuniverse.com/htc-tmobile-mytouch-4g-take-apart-repair-guide.html
Good luck!
Phew. Just replaced my digitizer using the latter video. Putting it back together was fairly straight-forward by just following the video backwards, though a 'put back together' video would be convenient.
A couple minor caveats:
They skipped showing some phillips screws holding the motherboard in place (near the end). I think there were two of them. They're fairly obvious if you know to look for them.
I attempted to reuse the existing adhesive by reheating and applying pressure. This sort of worked, but the digitizer seems a tad loose. I don't think it's going to fall off, but it'd probably be better to remove the old adhesive and apply some fresh adhesive. Anyone know where to get a suitable adhesive?
Taking apart the MyTouch 4G is not that hard
I bought a used MyTouch 4G in pieces on Craigslist for $ 45 that had a broken digitizer (about $ 20 on eBay with free shipping) and LCD (about $ 40 on eBay with free shipping) and the Audio & Volume Button Flex Cable (about $ 38 on eBay with free shipping) was also defective (the power button cable was ripped which can happen very easily if you take the phone apart and if you are not 100% careful when you pry the power button cable out). I ordered all the replacement parts on eBay from US sellers.
This particular phone had the "bad", washed out screen and was manufactured in Taiwan. When I ordered the replacement LCD and digitizer, I was hoping to get the "good", bright and superior screen but that didn't happen. So for the ones out there who are hoping to improve the screen by replacing the LCD and/or digitizer, it's a 50/50 shot.
I also ran into the problem with the adhesive and found a roll of 3M 2mm double sided tape for $ 10 with free shipping on eBay. The phone is working great and looks like nothing ever happened now after I put it all back together. And even though I had to pay for a lot of replacement parts, it was still a lot cheaper than buying a new one from T-Mobile or a used one on Craigslist or eBay
There are also a lot of MyTouch 4G disassembly videos on youtube. I'm a gal and if I can do it, you can too !!
This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver. If you don't know how to do this check out this teardown by ifixit: http://www.ifixit.com/Teardown/Motorola+Atrix+4G+Teardown/4964/1
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
I wanted to tell you guys why, but I don't know. Perhaps one of you guys wants to experiment applying pressure to each component separately to find out the culprit?
Also, I'm curious to know if this will work for all of you, or just some of you.
Here are the pics:
This last one is the piece of tin\plastic with tape, side by side with a pencil for scale. Its not the tin I used, but its basically the same, but the one I used has white paint, I don't know if should make a difference. If you're worried about shorts just cover the whole thing in tape or cut plastic from a bottle or something.
The first two are how its supposed to look in the end.
[EDIT]: Here are some more pics:
This is the piece of plastic I used. It doesn't show, but it is very thin, one milimiter thick, if even.
These are of the open device. In the last one the plastic piece is a little eschewed, but you get the idea.
Cheerios
Huh. This is similar to the fix some people did with the digitizer problem. Seems like the the connectors on this phone tend to come loose, to where pressure in the right direction will fix it.
Sent from my MB860 using xda app-developers app
Newbleeto said:
This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver.
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
I wanted to tell you guys why, but I don't know. Perhaps one of you guys wants to experiment applying pressure to each component separately to find out the culprit?
Also, I'm curious to know if this will work for all of you, or just some of you.
Here are the pics:
This last one is the piece of tin\plastic with tape, side by side with a pencil for scale. Its not the tin I used, but its basically the same, but the one I used has white paint, I don't know if should make a difference. If you're worried about shorts just cover the whole thing in tape or cut plastic from a bottle or something.
The first two are how its supposed to look in the end.
Sorry for no open device pics, I did this yesterday and don't really feel like opening my phone, but if you guys think its needed I'll do it later.
Cheerios
Click to expand...
Click to collapse
A detailed How To to show us what to do exactly, we can do much ourselves with just this pics. :/
EDIT: http://www.youtube.com/watch?v=SYz_RiuFVRk had anyone seen this?
Will try this with my wifi broken atrix tomorrow.
guidoido004 said:
A detailed How To to show us what to do exactly, we can do much ourselves with just this pics. :/
EDIT: http://www.youtube.com/watch?v=SYz_RiuFVRk had anyone seen this?
Click to expand...
Click to collapse
It's literally as simple as opening the atrix and placing the plastic under the motherboard, I don't think it gets any easier then that. But I'll try to take more photos.
As for that video, there are reports of people killing their mobiles by breaking the piece holding the battery or killing the nearby ICs trying that. That guy is just too rough. Also, it doesn't show the battery actually being replaced. If you wanna try to replace the battery, better do it gently and stay clear of that video
Sent from my Nexus 7 using Tapatalk 2
If the solution is to apply pressure to certain parts of the board then it's likely similar to the infamous nVidia issues from around 2008 where the chips were getting hot enough to expand and brake the solder connection or in some cases, rip some of the pads from the board. If that is the case, be careful, as flexing the board the wrong way could eventually lead to making it worse over time.
I can't believe this actually worked. Been using my Atrix for the whole weekend on WIFI. Also finally been able to use my Lapdock properly.
Thanks so much for such a simple fix.
If its any help to anyone, I ended up using an old debit card, as its seems the perfect height to give enough pressure on the board.
It did take a few goes, but as long as you persist with it, it works really well. Plus no more over heating too.
Thanks again
holy crap. 5 minutes and its fixed! thank you
Cause found??
Hi everybody,
I might have an idea what causes the wifi errors. As the wifi gets fixed by changing the motherboard's position, the motherboard is not fastened properly. This might be caused by the vibration function that is located on the part of the motherboard you would need to move up.(see the location of the vibrationfuction in the attachment.)
If so, should this function be less used then?
Thanks Newbleeto! I was so frustrated with this issue. I was initially trying based that youtube video link by someone else which never worked for me. I later decided to try your solution and it worked for me the very first time Appreciate your help!
Thanks, seems to work!
What an interesting tweak. There some validity to this. The Atrix 4G is notorious for wifi, bluetooth, and GPS dropout. This is largely due to kernel and rom. However I have seem plenty of Atrix4Gs with loose antenna clamps. Usually I apply a little pressure in the outside of the clamp to reform it slightly so it will maintain hold on the reciever socket. Second thing I look at is the shielding around the mainboard. This acts as a heatsink and guard. If depressed in anyway will cause massive heating along with grounding. The antenna clusters are not well separated from RF interference from one another to begin with. Metal in general will restricted RF signals considerably depending on its frequency. The greater the frequency the lower it's ability to perpetrate materials.
From the looks of it your directing RF crossover and bounce back away from each antenna. This is a good thing. It also means as long as the phone is not held on its edge towards any receiving end it won't effect talk and data very much.
My experiments with the Atrix4G always had a bit of unpredictable outcome when it came to pressure on the ribbon connections. This would result in the screen blacking out, digitizer over sensitive or non responsive, failure to boot and so on. Pressure is a big deal with these phones so be careful.
Happy tinkering
IT WORKS
after nearly 4 months of this bug i finally had the guts to open up my phone and do this fix.
and it is working , my wifi is back thank you OP. :highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::victory::victory:
This method works wonderfully. Thanks, OP!
sangyum said:
This method works wonderfully. Thanks, OP!
Click to expand...
Click to collapse
Spoke too soon. This fix stopped working after two days.... Back to Wifi Error and boot loop. :crying:
I got my wifi to work again, there are two snap on connectors on the same side of the phone. I put 2x pieces of toilet paper cardboard between the frame of the phone and the connector, pushing the connector tighter to the other side.
I'd like to confrm that it works to me !
Thank you, I spent dozens of hours to try solve it.
Newbleeto said:
This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver. If you don't know how to do this check out this teardown by ifixit: http://www.ifixit.com/Teardown/Motorola+Atrix+4G+Teardown/4964/1
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
...
Cheerios
Click to expand...
Click to collapse
I did this as well, and it's been working perfectly for over a week now. Battery life has tripled to 24h (back where it used to be, what a relief) and the wifi is back to being perfect.
In my case, I cut a small piece out of an old credit card and inserted into the section highlighted in the attached picture, inside to out (from the battery bay towards the side). There are flat cables/strips underneath and you probably don't want to insert your spacer material from the outside in. Make sure that the plastic strip fits completely underneath the board, otherwise you won't be able to properly close the back.
Thanks!
To add some data to this can all of you confirm the kernel and rom you are useing before and after this mod. Would help all of us in the future for reference. Thanks.
Cab121 said:
To add some data to this can all of you confirm the kernel and rom you are useing before and after this mod. Would help all of us in the future for reference. Thanks.
Click to expand...
Click to collapse
Sure, no problem!
Atrix 4G (Bell Canada)
Unlocked and rooted by yours truly (don't ask how, I'm still not sure I know what I did)
CynaogenMod 10.1 from epinter: Megathread or linuxmobile.org site, builds 2013-08-07 + hporch32 kernel (before and after mod) & 2013-08-26 + hporch32 kernel (after mod)
Radio: Telstra N_01.87.00R
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
bert682 said:
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
Click to expand...
Click to collapse
Ok so I did a little more reading and it seems that a gorilla has changed the screen on this phone in the past and he / she has used compound to stick the screen down and some of it has gone around the sensor and the resulting press down on the screen has created a few air pockets.
Looking less forward to changing the screen now as no doubt with my luck the "technician" will have used some crazy heat resistant glue!
Also....missing the speaker grille....funny how you only notice things after you have bought them!
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
It will work for sure, I posted this fix on a YouTube screen replacement guide of octopus glues I think and its confirmed to work from a lot of people. Then if you use a custom rom go to brightness settings while having auto brightness enabled and try changing light sources from dark to very bright places to see the instant lux values you get. If you are not satisfied with the result try custom auto brightness values.
Sent from my Nexus 4 using Tapatalk
bert682 said:
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
Click to expand...
Click to collapse
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Planterz said:
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Click to expand...
Click to collapse
I got a "kit" off eBay, [URL="http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT"]http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
That's the full part. The one you've posted is the type I usually go for, they're good quality so far.
bert682 said:
I got a "kit" off eBay, http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
Click to expand...
Click to collapse
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you), I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other components shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Planterz said:
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you, I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other comments shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video[/i] that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Click to expand...
Click to collapse
Awesome, I saw some cheaper screens but that one notes that its LG compliant etc. I bought a set of tools separately so will have all the stuff needed. Didnt think about the battery, will order one as it does make sense!
Thanks for the info, will update as I go.
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
bert682 said:
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
Click to expand...
Click to collapse
Yeah this is normal.
Sent from my Nexus 4 using Tapatalk
bert682 said:
New screen in and working well.
Click to expand...
Click to collapse
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Planterz said:
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Click to expand...
Click to collapse
No, not with the correct tools. I will admit had I not bought the plastic tools, tweezers etc I may have struggled.
The battery was my main concern, its really stuck down, even though this had been replaced before and likely a less tacky glue used it was still tough. Had to use some heat to soften it and the "battery cover" has seen better days. Next thing to replace is that, just for piece of mind.
All in all, pretty nice experience, the phone seems more modular that other phones I have taken apart which is nice.
I just got my new phone which is replacing a Droid2 which has some screen issues (looks like puddles of LCD in a couple of spots...like a melt).
Anyway, I had purchased a replacement screen about a year ago, but when I went to disassemble the device one of the screws was stripped. More than likely I stripped it - I think maybe the tools I bought were too cheap/soft and the screw was maybe in too tight.
Anyway, it's a little tiny screw and I don't know the best way to get it out. If this were carpentry I could drill in and use a reverse sink to pull it out, but I don't know how to deal with such a little one. I'm thinking maybe a dremel tool on the whole screw...but I really don't want to damage things more.
Also, best way to identify and get a replacement screw? This will just be a backup phone to play with...but I'd like to get it fixed.
thanks!
If required, I will post some pics (if I can capture them) in a few days when I have everything transferred and can fully retire and open up the phone again.
TraderJack said:
...Also, best way to identify and get a replacement screw? This will just be a backup phone to play with...but I'd like to get it fixed.
.
Click to expand...
Click to collapse
To remove it acrylic glue-it to a screwdriver and pull it (?!)
May I suggest buying some low density locknut.
keep the stripped screw (if it wasnt too tight) and put a drop of locknut at the end , secure others screws around first, not the prettiest but 100% effective
Just suggesting ...
Ltdrev said:
To remove it acrylic glue-it to a screwdriver and pull it (?!)
May I suggest buying some low density locknut.
keep the stripped screw (if it wasnt too tight) and put a drop of locknut at the end , secure others screws around first, not the prettiest but 100% effective
Just suggesting ...
Click to expand...
Click to collapse
thank :good:
If you have a dremel router then try to route a hex then use an allen wrench to turn it. If the screw is big enough it'll work. I need to see a close up picture of that screw. Maybe the slot can be retraced with that dremel.
In the process of fixing my phone I accidentally knocked off this little metal bit that I believe is for grounding since it seem to contact a metal plate attached to the plastic upper bit that doesn't seem to go anywhere else. Its a really tiny thing and I'm trying to decide how to best reattach it. I found someone on ifixit that posted a similar problem back in 2018, but with no solution (I posted there first but I guess cause its old no one is responding). He took some good photos, so I'll share his post: https://www.ifixit.com/Answers/View/476452/Component+broke+off+of+board,+is+it+necessary
The one I broke off is the one on the left. I'll attach to this a photo of my device with a macro shot I took of the area where it came off.
It looks like it was making contact through 4 tiny holes. I was thinking of maybe trying to flow a little bit of solder into their and then reattaching the metal bit with glue.
On the otherhand, is it pointless? I haven't tried putting the phone back together yet to determine what this effects or do I know if these ground points have redundant ground points else where.
Any advice would be appreciated. Thanks.