Related
Hi guys,
I have bricked my LG E400.Yesterday I try to downgrade my firmware with kdz. I receved an error ( kdz upgrade error wparam 100) and after that i turned off the phone.
Now my phone can't boot in any way and my pc won't recongnize it...
Plese help me! :crying::crying::crying:
have you try the combination button?
Vol up + down + Power, then after vibrate press home button
if it can't, maybe you have a hard brick, and you can call nearest service center
luthfi_11 said:
have you try the combination button?
Vol up + down + Power, then after vibrate press home button
if it can't, maybe you have a hard brick, and you can call nearest service center
Click to expand...
Click to collapse
Tried. No changes.
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
ferdo.smicilkas said:
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
Click to expand...
Click to collapse
I will try...thx anyway.
ferdo.smicilkas said:
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
Click to expand...
Click to collapse
I follow your instructions but my kdz doesn't want to detect my phone...my pc doesn't recognize the device...i don't know what to do except throw away it...
Before you throwing it away, did you install the latest drivers?
If not, you can do so by downloading and installing them from your support site or by downloading and installing LG PC SUITE.
After that please open device manager and see if there's anything there with an exclamation or a question mark. If there is, please don't continue and post back what it is.
Only when you see that everything is okay, disconnect your phone, turn it off, enter into emergency mode (by clicking volume up + volume down + power button), make sure that you're in emergency mode (the yellow screen), connect your phone, run Software update [KDZ] (KDZ-Flasher), make sure to set the right type (CDMA / 3GQCT), make sure to leave the PhoneMode in DIAG, browse your kdz stock firmware file, and then click on "Lunch software update".
I'll be looking forward for your comment.
Please don't give up!
I have installed the new drivers and the lg pc suite. The problem is that the phone won't go on emercency mode...
It seems dead.It also doesn't boot and the screen remains black when i push the power button.
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
medeno said:
I have installed the new drivers and the lg pc suite. The problem is that the phone won't go on emercency mode...
It seems dead.It also doesn't boot and the screen remains black when i push the power button.
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
Click to expand...
Click to collapse
What's happening instead of going into emergency mode, when you're clicking volume up + volume down + power button together? Is it seems dead the same way as you're clicking only the power button?
Did you try flashing your stock ROM again with Software update [KDZ] (KDZ-Flasher)? Is it even recognized in it?
What about the LG MOBILE SUPPORT TOOL? Same issue? It's not recognized?
BTW, you're saying that Windows 7 isn't recognizing the phone? Are you using the drivers that are provided by LG? If not, you can get them here.
need4steer said:
What's happening instead of going into emergency mode, when you're clicking volume up + volume down + power button together? Is it seems dead the same way as you're clicking only the power button?
Did you try flashing your stock ROM again with Software update [KDZ] (KDZ-Flasher)? Is it even recognized in it?
What about the LG MOBILE SUPPORT TOOL? Same issue? It's not recognized?
BTW, you're saying that Windows 7 isn't recognizing the phone? Are you using the drivers that are provided by LG? If not, you can get them here.
Click to expand...
Click to collapse
Any key combination on my phone doens't have any effect. I try to use LG supporto tool updating many times the drivers but the device is not recognized.
I'm thinking to take the phone to the service center.
If the phone not vibrate when turning on, its a hard brick and u can tell the service... They're propably replace the mainboard
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
medeno said:
Any key combination on my phone doens't have any effect. I try to use LG supporto tool updating many times the drivers but the device is not recognized.
I'm thinking to take the phone to the service center.
Click to expand...
Click to collapse
TravaPL said:
If the phone not vibrate when turning on, its a hard brick and u can tell the service... They're propably replace the mainboard
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
Click to expand...
Click to collapse
Well, it seems like a hard break - most definitely.
However, maybe one last chance before the service center.
Did you try to look in device manager while connecting your phone? Is there any refreshing while you're doing it? Are there any exclamation or question marks?
The reason I'm asking this is because of this:
medeno said:
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
Click to expand...
Click to collapse
That is why I'm not so sure your phone is dead. If it was dead - then why Windows playing a sound when you're connecting it?...
need4steer said:
Well, it seems like a hard break - most definitely.
However, maybe one last chance before the service center.
Did you try to look in device manager while connecting your phone? Is there any refreshing while you're doing it? Are there any exclamation or question marks?
The reason I'm asking this is because of this:
That is why I'm not so sure your phone is dead. If it was dead - then why Windows playing a sound when you're connecting it?...
Click to expand...
Click to collapse
I think the phone is freeze into emercency mode but anyway i take it to the service center...thanks for your help suggestions and help.
You welcome.
Please update how it was.
And if you have the time before you go to the service center, please check the device manager while you're connecting your phone.
It's very interesting, and it might help others too.
i have the same proplem
Guys same here Imposabile to use kdz because the device is just dead u cant charge u cant do anything its like pressing nothing at all
.
The proplem in the service center that might think that it was a wrong flashable zip was flashed to the deivce so the warrenty is void this way however there something called jtag solder cable or something
shady2137 said:
Guys same here Imposabile to use kdz because the device is just dead u cant charge u cant do anything its like pressing nothing at all
.
The proplem in the service center that might think that it was a wrong flashable zip was flashed to the deivce so the warrenty is void this way however there something called jtag solder cable or something
Click to expand...
Click to collapse
If i think correct, you hard bricked you device? (no boot etc)? (i'm not very good in eng)
I gave to the service mine kernel-bricked L3 (no boot, no vibrate, no emergency) and they repair it without any questions.
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
mmmm
idk about ur country but here in Egypt service sucks anyway lg guys told me if it was something related to software we will fix it but if it was hardware u will pay for it but i think hard brick is a software issue isnt it ??
shady2137 said:
idk about ur country but here in Egypt service sucks anyway lg guys told me if it was something related to software we will fix it but if it was hardware u will pay for it but i think hard brick is a software issue isnt it ??
Click to expand...
Click to collapse
You might say so, though usually in the service center they'll replace your board in order to get everything back...
Are you sure your phone is dead?
Maybe, like medeno, when you're connecting your phone you're hearing a sound in Windows?
need4steer said:
You might say so, though usually in the service center they'll replace your board in order to get everything back...
Are you sure your phone is dead?
Maybe, like medeno, when you're connecting your phone you're hearing a sound in Windows?
Click to expand...
Click to collapse
yes no sound its so dead
LG optimus f5 (P875), No boot no emergency mode
Hi,
I rooted my phone and now it doesnt turn on, even in emergency mode. But unlike in this thread i hear the windows sound of a new device and in the Device Manager it shows on other devices with a yellow exclamation mark QHSUSB_DLOAD.
I rooted the phone no problem but then i tried to partition the SD card but i ended up partition the internal memory (i think i erased everything even the OS), after reboot i couldnt turn on the phone.
Can you help me?
Hey guys,
Yesterday I tried unlocking my phone using the tools provided on this forum, but somehow my device got hard bricked.
It is just laying there with a black screen. It won't turn on, won't boot into recovery or emergency mode. Nothing.
But when I connected it to my PC (running Windows 7), I did hear the sound that it recognised it as a device, it just couldn't find any drivers for it, so I wen't to look into that.
Landed on the debricking method using QPTS on the CyanogenMod forums and I managed to find drivers for Windows 7, so no need for an XP computer!
There were some other Optimus L-series brickers who gave up on the process, but I have still some hope left.
Did all the work that had to be done, decompiled V20D KDZ for our device, converted the first 512 bytes of the partition.bin to .mbn, installed QPTS, and so forth.
Hooked up my phone to the pc holding the volume-down button, and QPTS actually recognised it as a phone in downloading mode!
Then that's where I got stuck. Using the HEX files from this thread, I get the following error:
Code:
Status: Software Download Aborted
Errors: Could not determine the HEX file's scrambling method. The file is invalid.
Do any of you have a clue on how get things working again?
The QPTS tool only lists MSM7x30 (eMMC) as ARMPRG to use for the phone in dowload mode, not the MSM7x27a we are using. Might this be part of the problem?
Any help is highly appreciated!
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Sent from my LG-P700 using Tapatalk
vaikz said:
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Click to expand...
Click to collapse
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Thanks for the replies, guys!
vaikz said:
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
Click to expand...
Click to collapse
I can't turn the device on. When I connect it to the PC, Windows sees the phone as an 'Unknown Device', even with the latest LG drivers installed.
And by KDZ flasher you mean the BC2App, right?
Lukijs said:
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Click to expand...
Click to collapse
Tried it a dozen times, with different combinations too. Only thing that happens is the sound windows makes when a device is plugged in.
Any chance a method like this would work? If the .img.zx file would be edited for our device ofcourse.
Hey all,
I couldn't get any further debricking my phone myself, so I just brought it to a repair shop. I'm hoping they can do something using JTAG or something.
Regardless of getting my phone working again (hopefully), I would still love to see if we can find a way to debrick hard bricked devices. If we can find a solution, I'll volunteer for writing a tutorial
Sent from my Nexus 7 using xda app-developers app
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
TonyMatt said:
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
Click to expand...
Click to collapse
1.-uninstall the drivers and programs lg l7 on your pc.
restart your pc, and reinstall all programs and drives
for your pc to recognize the phone.
2.-remove the battery, press the power button and volume + and connect the phone to the pc, buttons go into emergency mode
Try this a few times.
you may need to perform step 2 more times
why are you trying to enter emergency mode ?
TonyMatt said:
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
Click to expand...
Click to collapse
what are you trying to do with your phone to begin with ?
what system are you running on your pc ?
assuming its windows
do what he said and then see if any unknown devices (or with yellow triangle) in device manager.
post results
details ...
lokopol said:
1.-uninstall the drivers and programs lg l7 on your pc.
restart your pc, and reinstall all programs and drives
for your pc to recognize the phone.
2.-remove the battery, press the power button and volume + and connect the phone to the pc, buttons go into emergency mode
Try this a few times.
you may need to perform step 2 more times
Click to expand...
Click to collapse
i did try it many times till date havent succeeded...
IGGYVIP said:
what are you trying to do with your phone to begin with ?
what system are you running on your pc ?
assuming its windows
do what he said and then see if any unknown devices (or with yellow triangle) in device manager.
post results
details ...
Click to expand...
Click to collapse
i was running the stock version rooted on my phone.. i was doing a shutdown procedure to complete 2nd partitions script mounting. after shutting it down my phone never started. dats y i tried getting into the emergency mode to flash stock rom if in case of soft brick..
im using win7 and stock rom on my phone. moreover on connection with my computer it doesnt recognize my phone now...
TonyMatt said:
i was running the stock version rooted on my phone.. i was doing a shutdown procedure to complete 2nd partitions script mounting. after shutting it down my phone never started. dats y i tried getting into the emergency mode to flash stock rom if in case of soft brick..
im using win7 and stock rom on my phone. moreover on connection with my computer it doesnt recognize my phone now...
Click to expand...
Click to collapse
is your phone in bootloop ? or does it display blank screen ? (black or white)
did you try to remove sdcard ?
did you try to hard-reset ?
can you try to remove anything related to lg from your pc ? (all programs and drivers)
do you have qmemo button on top of volume buttons ? you can try to enter safe mode (most scripts will not work in this mode so you might get lucky)
@TonyMatt
Hi all,
I have a serious problem with my G2 which I could not solve: I used the new LG Flash Tool 2014 with stock KDZ file, everything was going just fine till I received an error message that LG server is not available, I disconnected the USB cable by mistake from my G2 and afterward I saw that it was in the middle of flashing process (12% was completed). I turned it off and tried to reach download mode again and nothing!, I'm receiving the "LG" logo and nothing- the screen goes black (it is still on).
I tried also to connect my phone to the computer- I received a list of 13 "new" local disks "H" to "T", only "H" disk is available and it's showing "image" folder with list of files.
I cannot reach "download mode", nothing is working!
I hope this is not the end for my G2..
please help me
Thank you so much!
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
wulsic said:
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
Click to expand...
Click to collapse
Thank you for your reply. I found this on the sticky threads: "[FIX] NO Recovery mode, No download mode, after OTA on rooted LG G2".
I installed ubuntu and followed the instructions. when I type the following: "gdisk -l /dev/sde" I receive an error message:
"GPT fdisk (gdisk) version 0.5.1
NOTE: Write test failed with error number 13. It will be impossible to save
changes to this disk's partition table!
Problem opening /dev/sde for reading! Error is 13
You must run this program as root or use sudo!"
My device is not rooted, is this the problem?
Please help me!!
Thanks
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
wulsic said:
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
Click to expand...
Click to collapse
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
NNCa said:
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
Click to expand...
Click to collapse
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
wulsic said:
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
Click to expand...
Click to collapse
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
NNCa said:
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
Click to expand...
Click to collapse
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
wulsic said:
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
Click to expand...
Click to collapse
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
NNCa said:
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
Click to expand...
Click to collapse
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
wulsic said:
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
NNCa said:
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
Click to expand...
Click to collapse
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
wulsic said:
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
Click to expand...
Click to collapse
Yes, I checked it- no response during connecting/disconnecting the device..
Maybe I did a mistake when trying to push those image files.. I guess there is nothing I can do to fix my phone..
Do you have any other suggestions?
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
NNCa said:
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
Click to expand...
Click to collapse
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
wulsic said:
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
Click to expand...
Click to collapse
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
NNCa said:
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
Click to expand...
Click to collapse
Hi, sorry to say but you have unfortunately completely hardbricked your device. It happened to me too however I was able to get it replaced under warranty at no extra cost.
What happened was that when your phone was still detected by linux, you had a chance to recover by flashing the correct partitions to gain access to download mode and from there, flash a KDZ to go back to complete stock. However, the files you used were probably incompatible with your variant which has now corrupted your bootloader sequence. I suggest you read this reply by fizzy177 as well as the rest of the thread: http://forum.xda-developers.com/showpost.php?p=51522304&postcount=118
So right now, you cannot do anything as you have already found out, no computer will recognise that your phone is plugged in. Your phone fails to boot when you try enter the download mode and it just freezes on the splash screen which looks like this: http://www.lg-phones.org/wp-content/uploads/2014/03/image2.png
What's meant to happen is your phone should load past that initial splash screen into this http://www.androiddunya.com/wp-content/uploads/2014/01/LG-G2-DownloadMode.jpg which accepts KDZ flashing and warns the device has been rooted.
So it's a blessing that your phone cannot boot as LG cannot find out you have voided warranty and you will be able to get a replacement free of charge.
Issue was solved- device was fixed under warranty
Hi,
I just want to update you all that my device was fixed under warranty! (motherboard replacement)
Thank you all for help and great support, this is a great forum with great community :good::good:
Hello
From past 2 weeks i am wondering on internet for a solution . Hours and hours of surfing and articles but still
Hope some one solve this issue.
Okay. First i m using LG G2 F320 K update to lollipop . Non rooted. It was working fine . I can transfer files in MTP .
But about a month ago i get an update for my phone . And after some days i need to transfer some files to my phone , i wonder when i connected my phone to computer nothing happened . No notification on mobile for changing PTP MTP option . Also nothing happened in Computer device manager..
From that day i am unable to connect my phone with windows 10. It always charging mobile.
I uninstalled all drivers in device manager and installed from LG website. I updates windows N and NK MTP update from windows for windows 10.
I changed different data cables and different computers and different ports . All stuff i can do. Still no luck.
When ever i plug USB data cable it always put my Mobile on Charging . No notification on Mobile. Also i go in setting > storage> and there is no option in upper right corner to select USB PC connection .
I am in developer mode and debugging mode is on also. Also USB tethering option is Disabled .
Kindly some one help me regarding this.
LG G2 F320K updated to stock Koren lollipop 5.0.1 . Non root.( i updated lollipop in April 2015)
Issue i am facing is no notification for Charging/ MTP/PTP Usb Debugging on mobile notice bar when i attach my phone using USB cord with computer. Also in computer device manager nothing happen. Even i checked on windows 10 , 8.1, 8, 7 .
I remember it was working like charm 4 weeks before I can change MTP PTP or Charge only mode by selecting notification when i attach it to my laptop. I can transfer files can use LG PC suit .
Then i received an software update like 40 mb and i updated my mobile. That i remembered.
After that 2 weeks before i need to transfer some books from laptop to my mobile. When i plugged my device there no notification to select MTP mode . Also there is nothing happened in my windows 10. I looked in task manager. No yellow icon in computer task manager for driver thing.
Laptop is just silent and mobile is just on charging .
Then i go to setting in LG and looked for USB PC connection settings. I wonder there is nothing . Settings > storage > 3 dot in upper right corner.. it suppose to be there . But here is no 3 dot in storage. Then i looked into share and networks in android setting and i found that USB tethering. But its faded mean it is disabled and i am unable to use this feature also.
I tried on different computers different cables , original, but nothing. Always when i plug usb mobile went on charging and in all computers nothing happen in device manager.
USB debugging is on.. I factory reset device 2 times. but useless. Also i uninstall all drivers from my laptop and then reinstall drivers from LG website also i tried google drivers , ABD, different ports. Nothing nothing happen.
Also now if i try put mobile on download mode by turning device off and then push + vol button and then put cord in mobile . No download mode also it went on charging. Well charging from laptop or from charger is okay.
Hope i explain all.
hello guys i got this phone of a friend, lg l5 e460, he gave to me to check if it can be fixed but after a fast vision i'm totally mad with it... can't boot recovery or download mode.... all i can see is : connecting it to the pc via usb cable i found this
http://forum.xda-developers.com/attachment.php?attachmentid=3004366&stc=1&d=1415396302
could any1 pls tell me how to fix this disaster?
LeGrim said:
hello guys i got this phone of a friend, lg l5 e460, he gave to me to check if it can be fixed but after a fast vision i'm totally mad with it... can't boot recovery or download mode.... all i can see is : connecting it to the pc via usb cable i found this
http://forum.xda-developers.com/attachment.php?attachmentid=3004366&stc=1&d=1415396302
could any1 pls tell me how to fix this disaster?
Click to expand...
Click to collapse
does the lg logo show up when you conect usb?
If so you can try to remove the battery, hold the button combination for recovery and conect to the charger or usb. Dont press power button at all. Just the combination for recovery.
Sent from my LG-P705 using XDA Free mobile app
Nesh89 said:
does the lg logo show up when you conect usb?
If so you can try to remove the battery, hold the button combination for recovery and conect to the charger or usb. Dont press power button at all. Just the combination for recovery.
Sent from my LG-P705 using XDA Free mobile app
Click to expand...
Click to collapse
I already tried that... i also tried home button + volume button, also camera button + home + volume, with battery and w/o battery via usb, nothing seems to work :S
LeGrim said:
I already tried that... i also tried home button + volume button, also camera button + home + volume, with battery and w/o battery via usb, nothing seems to work :S
Click to expand...
Click to collapse
you may have a hard brick, that cant be fixed. Only if you send your phone to LG.
Sent from my LG-P705 using XDA Free mobile app
But there's a device in device manager when i plug in via usb, i can't believe there's no way to fix it... like some recovery tool... T_T
LeGrim said:
But there's a device in device manager when i plug in via usb, i can't believe there's no way to fix it... like some recovery tool... T_T
Click to expand...
Click to collapse
well if you can get it in download mode some how you can flash kdz.
But dont know how.
You can try to remove bat and hold the vol down button. (I think thats how you enter download mode) and conect the phone to the pc.
Nvm if it wont show download mode on the phone just try flashing kdz.
Sent from my LG-P705 using XDA Free mobile app
HELL YEAH, I DID IT !!!!!! Something is changed now, i tried to pull out the battery, after i've installed LG USB drivers, holding Vol+, Vol- and Power Button i plugged in the USB clabe (WITHOUT BATTERY), now the screens is stuck @ the LG logo with " => Download Mode" in the corner
So... what come next? i guess i need this kdz... mmh... i think i need some googling
LeGrim said:
HELL YEAH, I DID IT !!!!!! Something is changed now, i tried to pull out the battery, after i've installed LG USB drivers, holding Vol+, Vol- and Power Button i plugged in the USB clabe (WITHOUT BATTERY), now the screens is stuck @ the LG logo with " => Download Mode" in the corner
So... what come next? i guess i need this kdz... mmh... i think i need some googling
Click to expand...
Click to collapse
yup you have the kdz instructions here on xda for L5 2.
just google kdz for l5 2 youll find the instructions. Its all easy after that.
Sent from my LG-P705 using XDA Free mobile app
Nesh89 said:
yup you have the kdz instructions here on xda for L5 2.
just google kdz for l5 2 youll find the instructions. Its all easy after that.
Sent from my LG-P705 using XDA Free mobile app
Click to expand...
Click to collapse
I'm stucked, draggin "automatic Offile procedure.vbs" on the admin cmd, i put the kdz file, RECOVERY mode then "Normal web update test"->"Upgrade Start", then LG MOBILE support tool starts and after he recognize the phone it crash... May it be something wrong with the OS im running on? i'm on W8.1 64bit... sorry for my english
No its not the os, right click on my computer find advanced and unfer modem disable lg mobile modem then restart your pc.. And check if you installd kdz and every thing thats needed corectly.
Also activate windows enabler.
Sent from my LG-P705 using XDA Free mobile app