I am having a problem pairing the remote. It just stop working, I have done soft reset and hard reset plus I re-flashed stock. I even tried another remote. It wont pair at all and even the remote wont show... I am hoping this is not the end of it. Please I need some help if anyone knows how... thanks...
Related
I, stupidly, wanted to see if Pocket Controller video acceleration would have any beneficial effect on my Universal, I selected the "test" mode and soft resetted the device.
Pocket Controller informed me that if the 'acceleration' didn't work another soft reset would return my device back to it's original state. Well I've tried probably 30 soft resets and my Universal simply hangs with my o2 screen showing.
A look at their website and there's a mention that the video acceleration is not supported in WM5 but no mention about how to fix it if it is enabled.
Can anyone give me some help as to how to prevent my Universal from trying to use Pocket Controllers video driver without me having to hard-reset.
Any help would be greatly appreciated.
I tried it on my old JAM and a hard reset fixed it. Hope you find a better answer than that.
Hard Reset be thou my savior.
At least this serves as a warning to others. Don't try it.
Typical! I tried this yesterday, and I had to hard reset mine yesterday afternoon, too.
If only I'd been 24 hours slower, I would have seen this thread and wouldn't have bothered!!
Hi there,
as strange as it may sound, i want to uninstall A2DP "properly" without having to do a Hard Reset.
I'm having a big issue with it, and even Hard Reset didn't worked anyway.
I'm afraid that just removing the files and removing the keys won't be enough.
Is there any procedure for that?
Did anyone tried and succeeded?
Thanks
Hi all, first time poster long time browser I checked the wiki and did a search but couldn't find a similar post. Here goes..
Yesterday i tried to connect to this protected wifi at a coffeeshop, but my HD did not manage to connect even after entering the network password. In the end it froze. The home screen was showing, i could feel the vib when pressing the screen, but no action happened. I did a soft reset, but that didnt make a difference... nothing working still, while it is still trying to connect to wifi.
Then I first did one hard reset. I managed to get to the screen where i am asked to touch the screen in order to configure the device. While i could feel the vib, nothing happened. I did a second hard reset, ended up at the same screen, but this time there is no vib when pressing the screen... and still nothing is happening. Same situation when doing a third hard reset.
I am lost for ideas.... Have anyone of you ever experienced something similar and what did you do to resolve it? Or have anyone any suggestions as to what I should try next??
Very bad dude,
what you can do (i dont know if this will work).....Flash your original rom again. it is a kind of a hard reset, but maybe this will work.
can you boot to boatloader (three color screen), and see the text USB when connected to pc?
Hi Kadir,
thanks for your answer.
I am trying to flash my rom using the excellent tool Hard-SPL package from OliNex, but to no avail.... i keep getting error message 202 meaning that it can't connect with the device...
This may sound obvious, but just in case... have you tried to remove the battery when the device is turned off? Is the only way to ensure you are fully turning it off, in case you have some kind of 'static' acting up. I had a similar issue on a PDA and also in my notebook, and was solved by removing battery.
hi,
thanks for the advice. I wish this was all it took, but alas no, i am not that lucky. I am starting to think this is a hardware issue....
can you see the 3 color screen?(when phone is off push power on + volume down button and keep volume down pushed).
if yes can you see it you are now in the bootloader. just chech if you see text usb, this means its connected.
and then flash, no 202 anymore.
do not use hard spl if you want HTC to repair your phone(warranty issue)
Don't you have to disable USB connection in ActiveSync too? Or was that just me?
I found the Flash program killed active sync anyway, but you're right all the guides say to disable it.
Hi,
From some strange reason I've suddenly got no sound from the earpiece (speaker is ok). Sure it was working ok yesterday
I really hope this isnt a hardware fault. I have only installed a few extras like Task Mangager, Net Framework 3.5... I wouldn't think that this would cause the problem??
Havn't done a hard reset yet, as its all set up... but might that help?
Am about to cry, so any help would be greater appreciated.
Thanks
A
If it's not a hardware fault, a hard-reset should help for sure.
Maybe thats the easiest option you have. Becuase then, you can set up every application you want to use step-by-step and check for earpiece-funtionality after every setup.
This way you'll be able to detect the "bad" application which silences your earpiece.
Well, if it's a hardware fault you'll know right after the setup-wizard
I'm now trying to do a hard reset to resolve the problem.... but that dosn't seem to work!
Held Vol UP & Down buttons down (as best as I can) and tapped on the power button.... nothing. How long should you wait...?
Do you think 02 would have removed this reset procedure in their ROM?
Any help would be appreciated
Thanks
Did a hard reset by leaving the phone on, pressing the vol up& down and then putting a paper clip on the reset.
I REALLY want to cry as this did not fix the problem. Been onto O2 and it has to go back... really dont have a clue how long the repair/replacment process will take.
I dont think there is anything else I can do. Was working fine yesterday.
But if anyone knows better then would love to hear from you.
A
Hello evryone,
I'm a bit in a pickle here, i got a smart TV (zephir store brand) that costantly loops trough the zephir logo and smarttv logo.
As far as i know the tv fuction perfectly fine until the previus owner tried to performe a firmware update, during the update something went wrong and now we are in this situation.
Till now i have tried the following:
Turning it of and on
Un plug the power and wait for 1h
Tried to perform a factory reset via remote
Tried to perform a factory reset while holding the power button
Tried to perform a factory reset while holding the power button and the volume down button
Tried to perform a factory reset while holding the power button and the volume up button
Tried to connect an usb keyboard
tried to connect via usb to PC
Nothing of the above showed any sing of response at this point the owner has given up on the TV but i still wana try to use it as a second monitor or something, so with all of that i'm coming here to seek the wisdom of the XDA forums. Any and all help would be apriciated form jailbraking to rooting, turning it into a monitor with no android fucionality, how to access the shell file anything at all.
Alright, so I couldn't find any firmware anywhere whatsoever for the Zephir brand. Tried loading a differend brand one for the same logic board. Managed to boot it but the picture was inverted and doubled. Made it to the source selection screen. Attempted to load a different firmware. The tv crashed while loading the booter. Now it won't even turn on the power indicator LED. So I guess it's well and truly cooked.
I could find the board online for like € 40 but I'm pretty sure they come without any firmware or OS? Does anyone know if it'd be worth a try, especially without being able to source the OEM firware?
Does anyone know if there is a way of making just the screen run on an arduino or something, I only need it to run HDMI anyways, 'cause I was planning on using it as a monitor anyways. The logic board is a CV538H-a.
If anyone has a suggestion I'd be glad to give it a go, otherwise i guess I'll bin it.