Database Users

[Q] N9005 mmc write fail

need help
i have a n9005 that i cant use (dead).
No recovery, only download mode
Odin mode
Product name: sm n9005
current binary :samsung official
system status fficial
reactivation lock (KK) OFF
knox kernel lock: 0x0
know warranty void :0x0
qualcom secureboot :enable (CSB)
Rp swrev; s2, t2, r2, a3, p2
write protection: enable
UDC Start
when i powered it ON, only phone model appears.
when i repeat this process, sometime an error message " mmc read fail" appears.
I cant remember the product code so i tried different firmwares but ODIN fails and says "mmc write fail" , "there is no pit partition" message
when i tried adding pit file thru ODIN, "mmc write fail" appears
hope you can help me

Hi,
This just happened to me today. I was messaging a friend on my phone when all of a sudden it shuts down. Now when it reloads after the samsung logo I box pops up saying Unfortunately, System UI has stopped.
Anyone please help us

[Q] please help: sbl1 partition doesn't exist

i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?

scienex said:
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
Click to expand...
Click to collapse
Could be an emmc failure.. But I'm sorry to be late to the post

thnx mate!
it's four phones ago
but i appreciate your reply :good:

scienex said:
thnx mate!
it's four phones ago
but i appreciate your reply :good:
Click to expand...
Click to collapse
Absolutely boss!

[HELP!!!] Need Help with SW REV CHECK FAIL: Fusion 3 > Binary 2

Hey there, I'm new to the whole rooting thing, and I messed up while doing it the first time so I get stuck at the Samsung Logo now, and it says while on that screen 'SET WARRENTY BIT: KERNAL', which from what I have read online means that my bootloader is messed up, but I don't know how to fix it. I will provide as much information as I can while not being able to load into my phone.
Info:
Model: SM-S902L(GP)
GPSAS902CB
FFC ID: A3LSMG900V
Galaxy S5 (TFN Region)
I've tried custom bootloaders, Stock Firmware, Factory Reset. Just about everything I can think of. I've even tried the stock firmware for my model.
I get the error: SW REV CHECK FAIL: (aboot) Fused 3 > Binary 2
Additional Info (From Screen):
ODIN MODE
Product Name: SM-S902L
Current Binary: Custom
System Status: Custom
Reactivation Lock(KK): Off
Knox Warranty Void: 0x1 (1)
Qualcomm Secureboot: Enable (CSB)
AP SWREV: S1, T3, R1, A3, P1
UDC START
If anybody can help that would be much appreciated!

Is "Set Warranty Bit : kernel" the brick message of death?

Hi all,
Smg900p Sprint s5 had the new CM13 nightly and seemingly out of nowhere it rebooted to "Set Warranty Bit : kernel"
When I switch to download mode this is my screen:
ODIN MODE
PRODUCT NAME:SM-G900P
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: Ox1 (4)
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T3, A1, A3, P1
SECURE DOWNLOAD : ENABLE
UDC START
The message "SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1" is added to this after I attempt flashing the stock rom with Odin. Any advice would be greatly appreciated!

After I installed a custom ROM on my s5, s4 and sm-g350 this message came. I think it's pretty normal.

Polyparadox said:
After I installed a custom ROM on my s5, s4 and sm-g350 this message came. I think it's pretty normal.
Click to expand...
Click to collapse
When I reboot all I get the Samsung Galaxy s5 screen and at the top in those yellow letters "Set Warranty Bit : kernel" and it's stuck there.
Tried deleting everything and flashing stock rom from both RWilco and Sammobile and it doesn't work. I suspect my the bootloader is dead which I'm working on now OR that I tripped the knox security which forced it to lock.
I've seen suggestions on downgrading to 4.4.2 but believe that there isn't a way to download for this model. I've tried Sammobile's version and it doesn't work.
This sucks.

Why don't you try refreshing the bootloader with Odin?

Polyparadox said:
Why don't you try refreshing the bootloader with Odin?
Click to expand...
Click to collapse
Sorry, I'm not sure I know how to do that. I'm researching and working on the bootloader info right now. Any advice is much appreciated.

Note 4 reboot frozen

Hi all. Can Someone pls tell me what is happening here and what should i do?the phone tried to restart on it's own and now its stuck here on restart screen with this messages
Could not do normal boot.
Ddi : mmc_read failed
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SW- N910F
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK: ON
KNOZ WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE ( CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START[
And also under the droid it says
Downloading...
Do not turn off target!,

Could it be that you done a Update? you could try a factory reset

Say goodbye to your Note 4, eMMC failure! Samsung wants you to buy a new phone.