Hello,
Having issues with heimdall on Ubuntu 12.04.
I was trying to flash ClockworkMODs recovery but i just hit this issue:
Code:
sudo heimdall flash --RECOVERY recovery-clockwork-touch-6.0.3.6-jfltexx.img --no-reboot
Heimdall v1.4.0
Copyright (c) 2010-2013, Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Attempt failed. Detaching driver...
Claiming interface again...
Setting up interface...
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
0%libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
ERROR: Failed to send file part packet!
ERROR: RECOVERY upload failed!
Ending session...
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
ERROR: Failed to send end session packet!
Releasing device interface...
Re-attaching kernel driver...
Its been a while since i have done this, but i'm sure i have no issues before on this system.
Anyone know what the issue is?
I don't know what the issue is, but version 1.3.2 of Heimdall worked. I think the issue is in the latest version of heimdall somehow. The error thrown by libusb seems to be of the "not supported" type.
[/COLOR]
-=nezero=- said:
Hello,
Having issues with heimdall on Ubuntu 12.04.
I was trying to flash ClockworkMODs recovery but i just hit this issue:
Code:
sudo heimdall flash --RECOVERY recovery-clockwork-touch-6.0.3.6-jfltexx.img --no-reboot
Heimdall v1.4.0
Copyright (c) 2010-2013, Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Attempt failed. Detaching driver...
Claiming interface again...
Setting up interface...
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
0%libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
ERROR: Failed to send file part packet!
ERROR: RECOVERY upload failed!
Ending session...
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
libusb:error [submit_bulk_transfer] submiturb failed error -1 errno=12
ERROR: Failed to send end session packet!
Releasing device interface...
Re-attaching kernel driver...
Its been a while since i have done this, but i'm sure i have no issues before on this system.
Anyone know what the issue is?
Click to expand...
Click to collapse
memstick said:
I don't know what the issue is, but version 1.3.2 of Heimdall worked. I think the issue is in the latest version of heimdall somehow. The error thrown by libusb seems to be of the "not supported" type.
Click to expand...
Click to collapse
Hey, I know this thread is somewhat old... But I am running ubuntu 12.04 x64 as well. I only saw 1.3.2 in i386 at the github downloads for heimdall. Did you just install libusb-1.0 i386 as well to get heimdall 1.3.2 to work?
evarInward said:
Hey, I know this thread is somewhat old... But I am running ubuntu 12.04 x64 as well. I only saw 1.3.2 in i386 at the github downloads for heimdall. Did you just install libusb-1.0 i386 as well to get heimdall 1.3.2 to work?
Click to expand...
Click to collapse
Hey guys! Just wanted to let you know that if you are still having this issue, you need to update your kernel. If you are unsure how to do this, just drop me a line and I'll give you some links and info. Just remember to rebuild heimdall and libpit.
similar issue
I think i have a similar problem
i am using heimdall 1.4 on ubuntu 12.04, when i try to flash cwm recovery the program stops at detaching driver and does not even proceed to "Initialising protocol..." in the above image.
using samsung i9082
could someone help please.
yogneo said:
I think i have a similar problem
i am using heimdall 1.4 on ubuntu 12.04, when i try to flash cwm recovery the program stops at detaching driver and does not even proceed to "Initialising protocol..." in the above image.
using samsung i9082
could someone help please.
Click to expand...
Click to collapse
same, same device
sorry but... heimdall, works on i9500?
Hi,
I installed twrp by AutoRec and later ive loaded CM11. Now Im tried flash new baseband coz I lost autorotation and is problem with my signal strenght. I reboot phone into twrp and tries flash zip file but always failed:
"Checking for MD5 file...
Skipping MD5 check: no MD5 file found
Verifying zip signature...
E: Zip signature verification failed: 1
Error flashing zip '/sdcard/D802_EUR_KKMODEM_AOSP.zip'"
"Checking for MD5 file...
Skipping MD5 check: no MD5 file found
Verifying zip signature...
E: Zip signature verification failed: 1
Error flashing zip '/sdcard/KK_Baseband_D802.zip'".
By default the verification is disabled(unchecked if you prefer).
There I tried to flash my own zip and it fails if tje verification is enabled.
take care next time.
Hi guys... Here goes my first post ever on XDA, although i've been much of a reader of this community and everytime, i got my answers just right!!! So, here is my first issue that i couldn't find the answer for in this forum... So i thought it'd be good to see if we could actually make it work together...
So, I have an N9005 that's stuck on boot logo and it doesn't get further than "Galaxy Note 3 - N9005" logo. And in stock recovery, i get :
E:failed to mount /efs (No such file or directory)
E:failed to mount /system ((No such file or directory))
# MANUAL MODE #
--Appling Multi-CSC
E:failed to mount /system (No such file or directory)
can't mount '/system' (No such file or directory)
E:failed to mount /cache (No such file or directory)
can't mount '/cache' (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/last_recovery
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/recovery_log.txt
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/emmc_checksum_log.txt
E:failed to mount /system (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/log
E:can't open /cache/recovery/log
E:failed to mount cache (No such file or recovery)
E:Can't mount /cache/recovery/last_log
E:can't open /cache/recovery/last_log
E:failed to mount /cache (No such file or recovery)
E:can't mount /cache/recovery/last_install
E:Can't open /cache/recovery/last_install
E:failed to mount /cache (No such file or recovery)
===============================================
I have tried many options.. Tried to flash via Odin, 2 different ROMS... Flashed with PIT... Tried flashing Philz, TWRP and CWM recoveries... As soon as i get to the recovery the phone reboots... So, I'm just out of ideas what to do... Oh and applying from External storage doesn't work... I get more errors saying
E:failed to mount /cache (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:failed to mount /sdcard (No such file or directory)
Your help would be greatly appreciated guys!
What did you do before the bootloop?
This_Guyse said:
What did you do before the bootloop?
Click to expand...
Click to collapse
Thank you for your reply!
I bought it as a bricked phone... So i have no idea what the guy i bought it from did to it.... I feel like the Partition E is damaged and I, somehow, should repartition it.... And PIT file doesn't do it... It's not the hard disk, i think.... Any ideas???
I had something similar when i tried to downgrade modem., i currently have ng1 and i tried to nc2 and ng2 and i got this bootloop. If you are still able to access download mode there is hope
rhadee said:
I had something similar when i tried to downgrade modem., i currently have ng1 and i tried to nc2 and ng2 and i got this bootloop. If you are still able to access download mode there is hope
Click to expand...
Click to collapse
Thanks for the message, bro. Yes, i have access to Download Mode... and here is a log from ODIN i just flashed... Hence, i get "Can't open the serial(COM) port." right after "system.img.ext4"
I haven't downloaded the latest ROM though....
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N9005XXUENA8_385654_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/223> Added!!
<ID:1/033> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N9005XXUENA8_385654_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N9005XXUENA8_REV03_CL1277177.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OJV_N9005OJVDMJ4_1890515_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/223> Odin v.3 engine (ID:223)..
<ID:1/033> Odin v.3 engine (ID:33)..
<ID:0/223> File analysis..
<ID:1/033> File analysis..
<ID:0/223> SetupConnection..
<ID:1/033> SetupConnection..
<ID:1/033> Initialzation..
<ID:1/033> Erase...
<ID:1/033> Set PIT file..
<ID:1/033> DO NOT TURN OFF TARGET!!
<ID:1/033> Get PIT for mapping..
<ID:1/033> Firmware update start..
<ID:1/033> SingleDownload.
<ID:1/033> aboot.mbn
<ID:1/033> NAND Write Start!!
<ID:1/033> sbl1.mbn
<ID:1/033> rpm.mbn
<ID:1/033> tz.mbn
<ID:1/033> sdi.mbn
<ID:1/033> NON-HLOS.bin
<ID:1/033> boot.img
<ID:1/033> recovery.img
<ID:1/033> system.img.ext4
<ID:0/223> Can't open the serial(COM) port.
<ID:1/033> userdata.img.ext4
<ID:1/033> persist.img.ext4
<ID:1/033> modem.bin
<ID:1/033> Transmission Complete..
<ID:1/033> Now Writing.. Please wait about 2 minutes
<ID:1/033> Receive Response from boot-loader
<ID:1/033> cache.img.ext4
<ID:1/033> hidden.img.ext4
<ID:1/033> RQT_CLOSE !!
<ID:1/033> RES OK !!
<ID:1/033> Remain Port .... 1
<OSM> All threads completed. (succeed 1 / failed 1)
So you think it might be an issue with the MODEM?
There is no partition E, Android is not windows (E: is not E:\ ) E means error
Download (from sammobile) and Flash NH1 rom in ODIN 3.07 (don't use 3.09) while ticking phone bootloader update, auto reboot and F.Reset time. Good luck
If all else fails tell me, I will try to help again
---------- Post added at 03:54 PM ---------- Previous post was at 03:48 PM ----------
After analyzing your log, I found you have inserted 2 devices in Odin, and one of them failed while one passed so which is the one that is bricked? (Tell me the ID number from the log)
---------- Post added at 04:05 PM ---------- Previous post was at 03:54 PM ----------
Download Odin here http://dl-1.va.us.xda-developers.co....zip?key=3myULck9MJ_Z5D8VLb2ZqA&ts=1412957100
This_Guyse said:
There is no partition E, Android is not windows (E: is not E:\ ) E means error
Download (from sammobile) and Flash NH1 rom in ODIN 3.07 (don't use 3.09) while ticking phone bootloader update, auto reboot and F.Reset time. Good luck
If all else fails tell me, I will try to help again
---------- Post added at 03:54 PM ---------- Previous post was at 03:48 PM ----------
After analyzing your log, I found you have inserted 2 devices in Odin, and one of them failed while one passed so which is the one that is bricked? (Tell me the ID number from the log)
---------- Post added at 04:05 PM ---------- Previous post was at 03:54 PM ----------
Download Odin here http://dl-1.va.us.xda-developers.co....zip?key=3myULck9MJ_Z5D8VLb2ZqA&ts=1412957100
Click to expand...
Click to collapse
Oh man!!!! I love you, man!!! Thank you SOOOOO MUCH!!! That did it!!! I just got a chance to download the firmware today and after flashing it, it worked!!!! However, I didn't have IMEI... But i managed to fix it with SPT... And it's all working now!!! Except for the microphone that i have to change!!! I had forgotten about it.... But it's all working fine now!!! I'm such a happy man!!! And I owe this to you!!! Thank you again!!! :victory:
WhatEver Man - I've got the same problem with Verizon Samsung Galaxy Note 2 SCH-I605V. Gets stuck at Samsung Galaxy Note 2 screen on power up. When booting into recovery I get
E:failed to mount /efs (No such file or directory)
E:failed to mount /system ((No such file or directory))
# MANUAL MODE #
--Appling Multi-CSC
E:failed to mount /system (No such file or directory)
can't mount '/system' (No such file or directory)
E:failed to mount /cache (No such file or directory)
can't mount '/cache' (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/last_recovery
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/recovery_log.txt
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/emmc_checksum_log.txt
E:failed to mount /system (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/log
E:can't open /cache/recovery/log
E:failed to mount cache (No such file or recovery)
E:Can't mount /cache/recovery/last_log
E:can't open /cache/recovery/last_log
E:failed to mount /cache (No such file or recovery)
E:can't mount /cache/recovery/last_install
E:Can't open /cache/recovery/last_install
E:failed to mount /cache (No such file or recovery)
Tried this ROM I605_VRALJB_Restore.tar.md5.xz with Odin 3.07 and got the following. The Phone Bootloader Update button doesn't appear with this.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605_VRALJB_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Hope you can help me with this.
Thanks!
Can you please give me the link to the ROM bcs i am not able to find ROM
sorry if i am being a noob
But Please Help Me my phone is suffering a lot.
Most Samsung stock ROMs can be found on sammobile.com.
I would love to thank you as your helping me so much
but i am feeling sorry to say that the rom available in sam mobile is not working using your process.
The error that is arising is "Can't open the serial(COM) port."
I have installed the proper drivers
My phone is not working, i would be obliged if you can bring it back to working condition
Does the phone appear in Windows Device Manager? Does it appear as a com port in Odin 3.07?
Same problem here on Samsung S III
meyrub said:
Oh man!!!! I love you, man!!! Thank you SOOOOO MUCH!!! That did it!!! I just got a chance to download the firmware today and after flashing it, it worked!!!! However, I didn't have IMEI... But i managed to fix it with SPT... And it's all working now!!! Except for the microphone that i have to change!!! I had forgotten about it.... But it's all working fine now!!! I'm such a happy man!!! And I owe this to you!!! Thank you again!!! :victory:
Click to expand...
Click to collapse
Congrats, man. :good::good::good:
By the way, I have same problem on different device, Galaxy Samsung S III.
I have downloaded the ROM from Sam-Mobile, it's JellyBean v4.3 (when unboxing it, it was v4.1.2); later when I flashed it, it sadly failed.
My question is:
- Is it necessary to download the ROM with the original version, I mean the 4.1.2 version?
- Should I flash the PIT file, Bootloader, Modem, etc. besides the PDA file?
Thank you for your support.
Live staring at (phone's) screen is sad. Living without it is even sadder.
Please, help.
Try Soe said:
Congrats, man. :good::good::good:
By the way, I have same problem on different device, Galaxy Samsung S III.
I have downloaded the ROM from Sam-Mobile, it's JellyBean v4.3 (when unboxing it, it was v4.1.2); later when I flashed it, it sadly failed.
My question is:
- Is it necessary to download the ROM with the original version, I mean the 4.1.2 version?
- Should I flash the PIT file, Bootloader, Modem, etc. besides the PDA file?
Thank you for your support.
Live staring at (phone's) screen is sad. Living without it is even sadder.
Please, help.
Click to expand...
Click to collapse
Do you have the AT&T version of the s3? The AT&T version is the sgh-i747 and there is no stock ROM for the sgh-i747 on Sammobile; however, there is for the Canadian version of the s3 which is i747m.
I have the same issue on my galaxy note 2 please tell how do i fix it
i9500
meyrub said:
Hi guys... Here goes my first post ever on XDA, although i've been much of a reader of this community and everytime, i got my answers just right!!! So, here is my first issue that i couldn't find the answer for in this forum... So i thought it'd be good to see if we could actually make it work together...
So, I have an N9005 that's stuck on boot logo and it doesn't get further than "Galaxy Note 3 - N9005" logo. And in stock recovery, i get :
E:failed to mount /efs (No such file or directory)
E:failed to mount /system ((No such file or directory))
# MANUAL MODE #
--Appling Multi-CSC
E:failed to mount /system (No such file or directory)
can't mount '/system' (No such file or directory)
E:failed to mount /cache (No such file or directory)
can't mount '/cache' (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/last_recovery
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/recovery_log.txt
E:failed to mount /data (No such file or directory)
E:can't mount /data/log/emmc_checksum_log.txt
E:failed to mount /system (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:can't mount /cache/recovery/log
E:can't open /cache/recovery/log
E:failed to mount cache (No such file or recovery)
E:Can't mount /cache/recovery/last_log
E:can't open /cache/recovery/last_log
E:failed to mount /cache (No such file or recovery)
E:can't mount /cache/recovery/last_install
E:Can't open /cache/recovery/last_install
E:failed to mount /cache (No such file or recovery)
===============================================
I have tried many options.. Tried to flash via Odin, 2 different ROMS... Flashed with PIT... Tried flashing Philz, TWRP and CWM recoveries... As soon as i get to the recovery the phone reboots... So, I'm just out of ideas what to do... Oh and applying from External storage doesn't work... I get more errors saying
E:failed to mount /cache (No such file or directory)
E:failed to mount /cache (No such file or directory)
E:failed to mount /sdcard (No such file or directory)
Your help would be greatly appreciated guys!
Click to expand...
Click to collapse
i am having same problem with i9500, can anyone guide me, and are there any possibilities of data recovery
Go to the forum for your phone .
I tried to flash a new Rom but when the installation was over I got stuck in recover, and now Every rom I try to install I get this message:
Skipping MD5 check: no MD5 file found
assert failed: run_program("/system/bin/loki.sh") == 0
E: Error executing updater binary in zip ' /sdcard/Download/cm-11........zip'
Error flashing zip
Please help!!!
I dont know what to do
JJPP35 said:
I tried to flash a new Rom but when the installation was over I got stuck in recover, and now Every rom I try to install I get this message:
Skipping MD5 check: no MD5 file found
assert failed: run_program("/system/bin/loki.sh") == 0
E: Error executing updater binary in zip ' /sdcard/Download/cm-11........zip'
Error flashing zip
Please help!!!
I dont know what to do
Click to expand...
Click to collapse
Had the same problems. I had to flash a man then reroot:good: