Related
Not sure whether this should be asked in accessories or not, but has anybody found a solution to the inadequate height of the rubber bump-stops on the O2 Exec? Their height isn't quite high enough to prevent the keys touching the screen's part of the clamshell so you end up with the keys getting rubbed smooth, and marks on the case where they touch.
At the moment, I've got a couple of bits of sticky rubber foot on preventing the touch, but they are moving around on the adhesive since there's so little of it.
What we could really do with is somebody with manufacturing facilities to create replacement bump-stops that are taller than the original ones, unless anybody else has a solution?
Cheers,
Steve.
Nobody got a solution to this?
Cheers,
Steve.
Haven't noticed the problem until you mentioned it but that's because I've been keeping my unit in a leather case -- which actually prevents it from closing comppletely (I'm using the piel frama case with the new clear plastic cover)
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
You can rotate the screen by opening the flip cover of the case (ie: PielFrama; XAX case sold by expansys; and many others) Not too sure about your Brodit holder w/ a case though.
Surely there must be a good solution to this? I'd pay good money(well, some) for a set of bump stops that were tall enough to stop the keyboard touching. A bit of a design flaw, I guess...
Cheers,
Steve
what I do is, I sandwich a small cleaning cloth in between....this way, I have the cloth at all times to wipe the display when needed....and also protects the screen and the surroundings from touching the keypad! I use the cloth that came along with my screen protector....
have a great new year!
San
Hi
Has anyone got any ideas about where I can get replacement rubber bump stops (normal or extended height) for my Exec? One of mine has fallen off and got lost. I have tried contacting O2, but short of sending the device back for repair, which I don't want to do, they cannot help.
Thanks for any info.
Mark
I have same problem with my QTEK 9000. I have shiny dots obeside my Universal's screen which corresponds to where the keys are located on the keayboard. I believe this is a manufacturing defect, right?
Anybody was able to return their device because of these spots? I've had my device for 1 month and they're starting to irritate me.
StevePritchard said:
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
Click to expand...
Click to collapse
Maybe I'll screw a belt clip to my brodit car mount. A simple unclip from my belt and then clip it onto the car mount. It'd need some sides on the mount to keep it from rotating due to gravity but I could see this working. Anyone have contacts with Brodit and a good case maker?
Tron_Of_Borg said:
StevePritchard said:
Not sure how I would cope with a case - how do you rotate the screen or put it into a Brodit holder without having to take it on and off all the time?
Cheers,
Steve.
Click to expand...
Click to collapse
Maybe I'll screw a belt clip to my brodit car mount. A simple unclip from my belt and then clip it onto the car mount. It'd need some sides on the mount to keep it from rotating due to gravity but I could see this working. Anyone have contacts with Brodit and a good case maker?
Click to expand...
Click to collapse
I think I would rather find somebody who can manufacture taller rubber stops to replace the existing ones...
Cheers,
Steve.
Rubber Keyboard Bump Stops - possible solution
I've had a bit of a play with my Exec - my friend has lost one of his rubber bump-stops, so I prized one of mine out with a jewellers screw driver to find that they are just pushed in, and so it would be relatively easy to lose them, I think.
Using the same thin screwdriver, I applied super-glue to the recess into which the rubber stop sits, and then pushed the stop back in, but not all the way. Now I have a pair of stops that sit about 1-2mm proud of where they were originally, and they are glued in to prevent loss.
I'll try and remember to post back in a week or two to let you know how I get on with them.
Cheers,
Steve.
I sure hope that there isn't a seam down there where the rubber feet were! I'd hate to hear of a PCB glued to the underside of the keyboard cover.
You can see that there are internal components below the recess, but that's why I applied the superglue with the screwdriver around the inner edge of the recess, as opposed to just squirting it into the hole.
As long as you don't flood the hole with glue, none of it will drop through to the components beneath.
Cheers,
Steve.
hello to everybody!
i got my xda trion 2 weeks ago. after one week, it was impossible to bring the stylus into the xda. so i got a new one.
after again one week, the stylus wont come out of the trion.
someone else prob's with the stylus?
greetings
karl
+ 1, probleme like a wizard too
same ting happened with my TyTN today...
+1 with one week old tytn
Same here...
First I couldn't get it out / then I couldn't get it in / then it would simply slide in-and-out freely to the point that only gravity was holding it in place (sorry if this sounds dirty, but this is what happened).
Had to have mine replaced. I've heard this issue has been around since the Wizard...
I really hope I don't have the same problem on TyTn #2!!!
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
andmjones said:
After a few days of having mine suddenly the stylus was becoming enromously difficult to remove. At one point it just wasnt moving so after a forceful tug it pulled out and a tiny transparent square of plastic/rubber fell out with it. Looks like it was in there to keep it in place but i have no idea how to put it back in. Now the stylus removes fine and stays in place too :shock:
Click to expand...
Click to collapse
Same here TyTN 1 week old.
same here,
think I'll swap mine over for a new one.....
raptorian said:
I had the same problem.
Could not get the staylus in with my TyTN.
So I did the mistake and pushed it in... a "knack" sound alerted me that something bad happened. Could not get the stylus in still... so I yanked a small rubber plastic piece from the stylus hole on my TyTN. Now I can slide easily the stylus in.
From teh reports I heard my guess is that the rubebr plastic inside the TyTN is used to firmly hold the stylus in. While without this rubebr plastic there is nothing to hold the stylus until you fully place it inside the TyTN.
Click to expand...
Click to collapse
Same here in 5 days
happend with me after 2 weeks. I've been struggling for a week, and now it's workng again! Don't know how long it will last. I hope it won't brake down, I bought Hermes thrue internetshop. Always sick to return things.
I carry something like this, and only use the tytn stylus in emergencies. I'm hoping this will reduce wear.
Same here - less than 2 weeks.
:shock:
Same here 5 days, luckley I had a replacment on order for BT problems recived that today lets see how this one goes.
me 2
my TYTN's stylus wouldn't stay in the hole.
i sent my tytn to be replaced (due to BT problems and screen alignment)
and i hope i t won't happen again.
when i put the tytn in the box to be sent so the stylus stopped falling :? )
that is odd
My stylus is a little difficult to remove at times, so I had a look down inside the stylus hole and it appears that there are three of those little pink rubber squares protruding from the side and a dark rubber 'socket' at the end to grip the tip when it's fully inserted. The pink squares are obviously there to provide a little more grip along the length of the stylus, but my guess is that even without them the 'socket' at the end would hold the stylus in place. I imagine that over time the pink rubber will either soften up or disintegrate entirely with the friction.
Solution stylus problem
I had the same problem with my stylus, my solution is take a Poster Buddy Brand name Pritt it is so called here in Holland you can place posters and photo's with it on wals, doors etc. looks like white rubber glue, think I see it in the UK with the name Sticky here you can buy it with photostores and bookstores etc. Take a small piece of it turn it between your vingers to a small ball and put it in the stylus hole after that push it to the end with your stylus.
After I do this I have no further problem with the stylus it works great.
Same issue here... the 2nd day I had it a small transparent square rubber went out of the stylus hole. Now i can put it in and out without problems...
Loose/Jammed Stylus
I'm afraid sending device back for replacement/repair for the stylus problem and loose locking keyboard may only be a temporary fix. Having had my device dismantled I can see exactly what the problesms are with both stylus and keyboard.
For the stylus there is a small block of clear plastic designed to create a friction lock to stop it falling out. There is luckily another small plastic spring lock at the far end so if the stylus is fully in it should click in and not drop out even without the plastic block. The problem is that the plastic block is not held firmly in its slot and as it gets loose creates far too much friction against the stylus which can then drag it right out.
The loose keyboards are due to the metal runners (that you see on back of keyboard partially springing apart (breaking tiny micro welds) at the ends where they lock (or not!) open and closed. These runners if they have sprung open like this will never lock firmly again unless you perform a bit of DIY.
I have performed small operations to fix both these problems and my Keyboard now locks very firmly both open and closed. The stylus issue is dealt with internally with a felt runner at a specific location. BEWARE of course performing these operations will invalidate your warranty. I can be much more specific for anyone who wishes to contact me directly particularly with the keyboard issue which requires quite a chore in dismantling the device - though I can now perform this in half an hour start to finish (Not something I'm proud of with a new device, but I had to workout just how to do the fixes!! )
Actually otherwise I think TYTN is great - superb in fact which is why I did not send it back for repair - couldn't bear to be without it!.
PS Finger around the screen method works every time for me forget all that align screen caper.
Mike
@mikechannon: Do you have high quality pictures of disassembled device where we can see the chipset references? we need to gather information on the hardware used inside the Hermes...
HI there,
I need to replace my screen, so I ordered a complete unit (LCD Screen, Digitizer and front). Now, I have to problem how to fix it onto the housing. They used biadhesive tape, but when I first tried it, the screen did not react when pressing the buttons, for example. I had to press very hard until it reacted. So I guess, the distance was not high enough, wasn' it?
How do I glue in the screen? Which tape to use? How to center it?
Does anyone know which tape HTC uses?
Hey im panicing so bad rite now. I just broke my htc's LCD screen ! Mad sad from this disaster . Dont got much money so can someone please tell me whats the cheapest or best way to replace or fix it ? I really need help because im freaking out!
The repair choices
There are basically two choices. Doing it yourself or having it repaired.
In either case the most straight forward is to replace the screen and digitizer as one unit. I expect you can still see things on the screen yet its cracked from one corner. Its the digitizer on the top that usually suffers but its hard to replace by itself. There is a YouTube video showing how to do this (search on Replace Touch Screen on HTC HD2 on YouTube).
If you are game to do it yourself (an electronics tech would be able to do it fairly well, though it is still fairly difficult) then you can buy a complete screen and digitizer off ebay (around $100). Getting the unit out of the case is tricky as its held in with 4xT5 Torx screws (easy bit) and lock notches around the case (tricky part). I found thin stiff plastic bits slotted in between the module and the case works well at releasing the locking notches. Then press out at the top of the battery area, while pulling the top edge of the plastic case out and down with your finger nails. One side at a time. Don't forget to remove the SIM card and SD card as these will hold the module in place if not removed.
The double sided tapes used to hold the screen in place are a problem, but warming them up with a carefully applied heat gun does release them. I would add that there is no need to unscrew any of the electronics boards as the screen can be replaced without doing this. Releasing the screen ribbon cable connector is done by flipping up the black locking section on the ribbon socket. Slide in the new cable, lock it down, then curl it around as you slide it backward under the metal case so that the curl in the cable occurs in that small space under the metal rather than being folded over sharply, which can fracture the ribbon cable "wires" rendering the screen dead.
Press the screen back down onto the tape (hopefully the tape has remained slick enough as its all that holds the screen in place). Be careful to align the edges and top and bottom correctly, otherwise your buttons won't work and the screen will not sit in the case properly. You can test the buttons as you align to feel for the slight click. Be sure to test all four as alignment left to right is just as critical for full function as up and down. You should also watch to be sure the light sensor little plastic bit (its a small clear cube of plastic) doesn't fall out and disappear while you are doing the screen swap and it stays in place during reassembly.
Then press it home into the plastic case. I remove the volume button (if it hasn't fallen out already) as it tends to push the volume button pads out of alignment (they are only held in with yellow tape (be careful not to loose them). Then with it all snapped in place pull out at the volume button section and slot the button back in place. Orientation is fairly obvious with the button points lower down and the joining bar going behind the case plastic to lock it in place (all with the screen facing upward). You may find the volume button only works if you press down on the screen slightly. This movement will be taken up when you screw the 4 torx screws back in.
Finish by powering up (with fingers crossed) and test. Hopefully all working.
Alternatively, if thats put you off doing it yourself, get it repaired by a service agent (around $300). Then it comes back all done with a small warranty. Most of the phone providers will be able to direct you to a good independent service agent.
If there a teardown guide for the Wildfire? I'm planning on replacing the fascia to a black or white one
I googled it and I found the EVO and the Desire...
Thanks.
nicky041192 said:
If there a teardown guide for the Wildfire? I'm planning on replacing the fascia to a black or white one
I googled it and I found the EVO and the Desire...
Thanks.
Click to expand...
Click to collapse
Surely its pretty similar to the desire?
IcyWildfire said:
Surely its pretty similar to the desire?
Click to expand...
Click to collapse
It's what I was thinking but I'm not too sure...
I just did a screen replacement on a German Wildfire today, I used a desire guide briefly - but it was pretty simple. 8 screws and 3 ribbons in total isn't to bad for a full teardown.
Here's the brief:
1) remove back battery cover
2) remove battery, MicroSD, and SIM
3) remove 4 corner star screws
4) remove 2 philips screws from right hand rail (sim card side)
5) Unclip bottom bracket and remove
6) Unclip plastic back from both side rails and remove
7) Remove 2 philips screws from bottom right and top left of breadboard
8) Disconnect haptic feedback ribbon from bottom left by lifting the black lever and sliding out the ribbon (very narrow ribbon)
9) Disconnect screen and touch screen ribbons on right hand edge by lifting them up (they're snap-ons)
10) Lift volume board up from between main bread board and volume button
11) remove breadboard from front housing
12) Peel back the bottom ribbon from the back of the screen (it's glued on with light adhesive)
13) Lift up bottom corner of screen and remove screen from front housing
in the end you should have these pieces:
Front housing
Screen
Bread Board
Back Housing
Bottom Plastic Clip
Back cover
2 Small philips Screws (breadboard)
2 large philips screws (back housing right hand edge)
4 large star screws (back housing corners)
Sorry, I literally just finished this an hour ago. Hope this helps.
i tear-down my wildfire like SophT. my big problem is now, to put the new digitizer in the phone. the old was glued and now i didn't have any idea to fix the new in the phone. have anyone an idea ?!
i think i destroyed the new display. on both sides of the new one were a protective sheet. i removed both, the phone works perfectly, but there is no possibility to use the touchscreen. There are no inputs possible. Have I destroyed with the removal of the film, the new display?
w1st said:
i think i destroyed the new display. on both sides of the new one were a protective sheet. i removed both, the phone works perfectly, but there is no possibility to use the touchscreen. There are no inputs possible. Have I destroyed with the removal of the film, the new display?
Click to expand...
Click to collapse
I'm okay with this and I think it's hilarious.