BUZZ HTC Wildfire extreme Rebooting even in recovery - Hardware Hacking General

well i recently dropped my HTC wildfire in water. I took it to the service center a local shop
and get it cleaned. but right on the shop when the engineer repaired it; it keeps
on restarting again and again. i thought it was beacuse may be ROM get corrupted
and when i will return home i will boot into recovery and reflash it.
but when i came back to home i put the phone down and then tried to go to the
recovery , it again start rebooting again and again. i was unable to stay in recovery for a
few seconds. it shows the revolutionary recovery but again it reboot and shows the
HTC logo and then again reboot after few seconds. then i thought may be clearing the memory will
make any effect but still when i cleared memory from bootloader i managed to clear it and it
didn't gave me bootloop in bootloader. but as soon as i tried to again boot back to recovery from bootloader menu
it again start rebooting abnormally. well i thought there may be problem with the battery but when i put charger
in again the phone led shows orange color charging and then phone again start rebooting
when the charger was plugged in.
but it stays in bootloader on. battery checked it is working right.
now can somedbody tell me is it hardware fault or there is something wrong with software ??
i called the LOCAL HTC center they say that there is an IC in the motherboard of phone
it is responsible for making boot properly and may be water has runied it.
well as per them the repair is not possbile now because they just replace the whole board they
don't solder the IC'S and moreover in india HTC has halted the production of motherboards they
are not avaliable no more.
well is this the end of my little fellow phone ?

sachoosaini said:
well i recently dropped my HTC wildfire in water. I took it to the service center a local shop
and get it cleaned. but right on the shop when the engineer repaired it; it keeps
on restarting again and again. i thought it was beacuse may be ROM get corrupted
and when i will return home i will boot into recovery and reflash it.
but when i came back to home i put the phone down and then tried to go to the
recovery , it again start rebooting again and again. i was unable to stay in recovery for a
few seconds. it shows the revolutionary recovery but again it reboot and shows the
HTC logo and then again reboot after few seconds. then i thought may be clearing the memory will
make any effect but still when i cleared memory from bootloader i managed to clear it and it
didn't gave me bootloop in bootloader. but as soon as i tried to again boot back to recovery from bootloader menu
it again start rebooting abnormally. well i thought there may be problem with the battery but when i put charger
in again the phone led shows orange color charging and then phone again start rebooting
when the charger was plugged in.
but it stays in bootloader on. battery checked it is working right.
now can somedbody tell me is it hardware fault or there is something wrong with software ??
i called the LOCAL HTC center they say that there is an IC in the motherboard of phone
it is responsible for making boot properly and may be water has runied it.
well as per them the repair is not possbile now because they just replace the whole board they
don't solder the IC'S and moreover in india HTC has halted the production of motherboards they
are not avaliable no more.
well is this the end of my little fellow phone ?
Click to expand...
Click to collapse
The last thing i would suggest you is that to change recovery.try flashing some other recovery and see if it works.If the problem still persists,I'm afraid you'll have to give up on willy or buy a new second hand willy.Its pretty cheap these days.

Well i will definitely try to do that
Wasimk32 said:
The last thing i would suggest you is that to change recovery.try flashing some other recovery and see if it works.If the problem still persists,I'm afraid you'll have to give up on willy or buy a new second hand willy.Its pretty cheap these days.
Click to expand...
Click to collapse
well yeah i will try to do that i would be able to..can you tell me how to flash recovery from fast boot menu after connecting it with PC and re installing HBOOT drivers again. coz it was long ago that i had did it.:good:...

Download any recovery in pc49img format and put it on the root of your sd card. Then turn the phone on in bootloader mode, follow instructions and you're done. No need to connect to PC.

Donne
Wasimk32 said:
Download any recovery in pc49img format and put it on the root of your sd card. Then turn the phone on in bootloader mode, follow instructions and you're done. No need to connect to PC.
Click to expand...
Click to collapse
My phone is alive again and it is working one of my friend has repaired it.:good:

Related

brick boot loader to black screen: no simple solution, simple prevention

Hi
So last night when I flashed my new created ROM with CWM, it seems like I ruined my boot loader, and from that I can't find the way to recover
SYMPTOMS:
- black screen
- power button doesn't do anything
- no button combination boots to download mode
- no charghing indication when connected to charger or USB
- no detection in the computer when connected to the USB
Is this the real black screen of death?
How did I get there?
I flashed a ROM through CWM, when it finished I selected reboot from CWM, and since then, all I see is black screen, no indication whatsoever to powering up.
I didn't try a USB JIG yet, but I will at Thursday (meet with a friend that has one)
as far as I understand the only way to recover from this is using a RIFF Box JTAG which requires, taking apart the phone, and soldering small wires to the board, and then reload the boot loader
Where do we go from here?
If it happened to you Please write down:
how did it happened to you?
what did you do to try to recover?
did you mange to recover?
if you did, how did you?
Why is this post so important to everyone?
Because if it didn't happen to you yet it might happen in your next CWM flashing.
So its very important to find a solution or at least the way to prevent it.
- update 31/12/2010 -
Cause
corrupted boot loader , bad sbl.bin flashing
Prevention:
do not flash roms/addons/fixes with sbl.bin
if you must flash sbl.bin, do it while you are sure that your USB configuration is perfect, and do it as less as possible.
Solution (for those who already bricked to black)
you're not gonna like it
find riffbox jtag....
marcelo.waisman said:
Hi
So last night when I flashed my new created ROM with CWM, it seems like I ruined my boot loader, and from that I can't find the way to recover
SYMPTOMS:
- black screen
- power button doesn't do anything
- no button combination boots to download mode
- no charghing indication when connected to charger or USB
- no detection in the computer when connected to the USB
Is this the real black screen of death?
How did I get there?
I flashed a ROM through CWM, when it finished I selected reboot from CWM, and since then, all I see is black screen, no indication whatsoever to powering up.
I didn't try a USB JIG yet, but I will at Thursday (meet with a friend that has one)
as far as I understand the only way to recover from this is using a RIFF Box JTAG which requires, taking apart the phone, and soldering small wires to the board, and then reload the boot loader
Where do we go from here?
If it happened to you Please write down:
how did it happened to you?
what did you do to try to recover?
did you mange to recover?
if you did, how did you?
Why is this post so important to everyone?
Because if it didn't happen to you yet it might happen in your next CWM flashing.
So its very important to find a solution or at least the way to prevent it.
BTW I think its a developers post, because we need developers creative way of thinking to find a solution
Click to expand...
Click to collapse
Happened to me too. I was tinkering with the Armani source to hopefully find something of use for Axura, and I bricked it. Same things happened to me. I called att and got a new one.
marcelo.waisman said:
Hi
So last night when I flashed my new created ROM with CWM, it seems like I ruined my boot loader, and from that I can't find the way to recover
SYMPTOMS:
- black screen
- power button doesn't do anything
- no button combination boots to download mode
- no charghing indication when connected to charger or USB
- no detection in the computer when connected to the USB
Is this the real black screen of death?
How did I get there?
I flashed a ROM through CWM, when it finished I selected reboot from CWM, and since then, all I see is black screen, no indication whatsoever to powering up.
I didn't try a USB JIG yet, but I will at Thursday (meet with a friend that has one)
as far as I understand the only way to recover from this is using a RIFF Box JTAG which requires, taking apart the phone, and soldering small wires to the board, and then reload the boot loader
Where do we go from here?
If it happened to you Please write down:
how did it happened to you?
what did you do to try to recover?
did you mange to recover?
if you did, how did you?
Why is this post so important to everyone?
Because if it didn't happen to you yet it might happen in your next CWM flashing.
So its very important to find a solution or at least the way to prevent it.
BTW I think its a developers post, because we need developers creative way of thinking to find a solution
Click to expand...
Click to collapse
Did you try removing battery and putting it back and then opening ODIN, holding the volume up/down and inserting the usb to bring it on the download mode. I guess I might have experience almost similar issue with one of the rom. I almost freaked out. Phone wont show if its charging. It wont mount on the pc. But tried all the possible method available several times including adb shell command. And finally I did hear the magical sound from window when the usb is connected and finally it did work.
Also try the adb method if it doesn't go into download mode using volume button combo.
Sent from my SAMSUNG-SGH-I897 using XDA App
Did u remove sbl.bin
Sent from my SAMSUNG-SGH-I897 using XDA App
Happened to me the first time I ran the OTA update from ATT. Paused the update, and when I resumed it - the phone though I finished downloading the JH7 update and tried to apply it.
It failed to apply and when it went to restart, it never powered on. No download mode, recovery, USB power, Odin, nothing. It was completely dead.
I got it replaced at the AT&T store.
If sbl.bin was removed or corrupted you should call the warranty center. Tell them ota update bricked your phone. Lol good luck
sent from my cappy running di11igaf's rom v2.5 at 1280mhz!!
I think it is just bad luck. I was once being careless and had the battery fall out of my phone while flashing, it interrupted the flash and I was still able to get in download mode to Odin it. Needless to say, I'll never flash again without the back cover on
bulletproof1013 said:
Did u remove sbl.bin
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Yes i'ts probably a bad sbl.bin, but I didn't remove it I flashed a new one, most of the rom's do the same
yeah sounds like it...sry for your luck.but seems like its toast then. keep us posted
But if you had a batch 1008 captivate and you messed up during and Odin flash to stock then your screwed bcuz Odin one click swaps the sbl.bins to make your button combinations impossible. ADB would work but you obviously can't access that. I too have a 1008 and it sucks, that is why I bought a jig.
silverslotcar said:
But if you had a batch 1008 captivate and you messed up during and Odin flash to stock then your screwed bcuz Odin one click swaps the sbl.bins to make your button combinations impossible. ADB would work but you obviously can't access that. I too have a 1008 and it sucks, that is why I bought a jig.
Click to expand...
Click to collapse
There is a a way. Whenever you need to flash to stock you must use following stock. http://forum.xda-developers.com/showthread.php?t=818439
This is same as normal stock posted by DG except that it includes sbl.bin that we (1008) need. I use it everytime and 3 button combos for Download, Recovery work great.
silverslotcar said:
But if you had a batch 1008 captivate and you messed up during and Odin flash to stock then your screwed bcuz Odin one click swaps the sbl.bins to make your button combinations impossible. ADB would work but you obviously can't access that. I too have a 1008 and it sucks, that is why I bought a jig.
Click to expand...
Click to collapse
it seems like this is not my case
I'm still looking for other people who had my case, and recovered (even with the JTAG riff box) or at least find someone who know's what we shouldn't do, so we don't break our phones.
so whats batch 1008?
This happened to me last night. I was trying to flash the Darky port via CWM and during the flash it became unresponsive. I had to pull the battery. This caused 2 different things. Sometimes it would be a never ending loop of boot screens and then others it would just go into recovery where it wouldn't let me do anything.
From here luckily I was able to access download mode by using the "adb reboot download" command. So I then got into dl mode and tried to flash stock (not the 3 button fixed one) and it froze on FACTORYFS (or whatever it is). I had no choice but to pull the battery. Now it won't boot at all. So my assumption is it wiped the bootloader. I'm not 100% sure but I feel that the reason it stopped where it did was because I didn't run odin as admin on my Win7 pc. I read in another thread that someone had the same problem when they didn't do that either.
If you are in a pitch black room and you press power you can see your screen illuminate, it's just very dim.
I have batch 1008 if it makes any difference to anyone.
Either way I'm heading to the device support center in a half hour or so to try to get a replacement. I originally was going to make or order a jig but people are saying it only works if the bootloader is intact. I originally had hopes because one person claimed that they recovered a completely dead phone with it, but upon further reading all others could not. It seems like his phone may not have been completely bricked.
Update:
Just got back from the at&t device support center. They gave me a new phone without any hassle. They asked what was wrong with my phone and I told them that I was trying to update it and now it won't turn on. The guy tried a few combinations of button presses and tried hooking it up to a jig-like device. Nothing worked so he just gave me a refurbished phones. No questions asked. As I was walking out he said a few people have had the same issue so it's not a big deal.
Either way I thought this would help to realize that there is likely no way to get the phone to boot unless you have a jtag handy.
I don't feel safe to flash rom via CWM.
If you really want to do that, delete the bootloader inside the .zip
So i think i killed mine too
so i get black screen, two button combo gives me SEC S5PC110 Test B/d
I opened odin but nothing Is this toast?
I had this exact problem over thanksgiving weekend. My phone was was was hard bricked I was getting the "phone + computer" it took some effort to get it into download but I got it there and when I was recovering with odin the connection got lost the screen went blue and then nothing. It was dead totally unresponsive no charging or boot screen nothing but once I got a black screen with redlines. After a lot of attempts to revive it I gave up called ATT warranty for a replacement. Luckily I opted for the slow mail service and kept reading. Yesterday I saw the above post and now I can say "yes even now your phone is not bricked even though it does NOTHING"
step 1) first thing I did was charge the battery with my replacement phone as the bricked phone was no longer able to charge the battery
step 2) open odin1 click and hooked up the usb to the phone and computer no battery
step 3) inserted the battery holding only volume up+down
step 4) "BOOM" download mode and a happy dance
I posted this in the"read before flashing" thread there are other people who have recovered from this and now I think that the extra trick to this is getting a 100% battery you need this to flash, and state the phone is in now wont charge a battery.
hope this sound encouraging
silverslotcar said:
But if you had a batch 1008 captivate and you messed up during and Odin flash to stock then your screwed bcuz Odin one click swaps the sbl.bins to make your button combinations impossible. ADB would work but you obviously can't access that. I too have a 1008 and it sucks, that is why I bought a jig.
Click to expand...
Click to collapse
It's odd because I keep seeing people saying things like this. I, too, have a 1008 Captivate. My button combos have worked from day one and Odin one click has never messed that up. Maybe I'm just lucky?
Sent from my SAMSUNG-SGH-I897 using XDA App
RKight said:
It's odd because I keep seeing people saying things like this. I, too, have a 1008 Captivate. My button combos have worked from day one and Odin one click has never messed that up. Maybe I'm just lucky?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
I believe there's a "fixed" 1008 batch. Not all 1008s are going to have the problem.
norcal einstein said:
I believe there's a "fixed" 1008 batch. Not all 1008s are going to have the problem.
Click to expand...
Click to collapse
Yeah it's either that or just a misconception spread by the community. Both my old captivate and replacement were 1008. I have been able to get into recovery via the power+volume combination. I was also able to get into dl mode using the vol+insert usb combination.
It's possible I just got lucky on both but who knows.
I, and many others have a 1008 that don't go into download or recovery via the button combos without fixing sbl.bin.
Sent from my SAMSUNG-SGH-I897 using XDA App

Endless booting and no recovery access. I'm about to give up.

Help please. I'm basically in a boot loop with no recovery. Idk what I should do or if its possible to make a warranty claim.
Hey guys I'm in a boot loop of some kind. I'm not an advanced user of this stuff but idk what to do at this point. So this is the situation. I have a X10a from at&t and its rooted with busybox and freex10 recovery or whatever. I had a default 2.1 ROM and flashed the offline recharging thing. My phone seemed to work fine but then my battery died out. For a while I've had recharging problems with my phone either my cable is messed up or the usb port. So anyways after it died out I tried to recharge but I was in the 3x red flashing light problem and accidentally broke my charger cord, but continuing I borrowed my friends cord and still had problems so knowing my usb port is kinda broken i just left it there. After about 2 hours my phone majestically starts up lol. So I decided I wanted to put on xrecovery just incase and My computer wont read my phone. I try everything from takeing out my sd card to restarting my computer to reinstalling pc companion like 20 times. So I tried a factory reset through the phone settings and ended up where i currently am in a boot loop. It turns on and does the sony ericsson thing then does the boot animation then my phone vibrates and the screen darkens and my buttons are lit up. It has been like this for about 30 mins so far. I tried restarting my phone by taking out the battery and taking out the sd card/sim card.
Sorry for this being long but this is my situation. Could you please help me out? I Don't know if I can do a warranty claim or anything I'm desperate so please any help would be greatly appreciated. Thanks in advance. Also if there is anymore information you need please just ask.
use flashtool and flash a rooted generic 2.1 rom
install xrecovery
restore a back up
My computer can't read my phone. How can I fix that? It can go into flash mode but nothing shows up not even in the /:c/ area
if your phone is in flash mode, it's fine. start flashtool, click "flash", select the rom you want to flash, put phone in flash mode (turn off, hold back button while plugging phone in, wait for green light), click ok, let it do it's thing.
Even when i go into flash mode it doesn't work. It goes in flash mode while it searches then after a while the x10 leaves flash mode. Tbh I think its my cable though. Any idea where to get an official one that will ship to hawaii?
You may be missing the drivers.
Install SEUS "Sony Erricson Update Service" from the sony erricson website.
And let it detect your phone at least once.
You can also use it to restore your phone.
Good luck.
I got all the drivers. I'm just gonna buy a Xperia Play and see if i can fix my x10 and sell it or somthing. But thanks for all the help guys
Go to flashtool, press on flash select firmware. Then after it asks put your x10 connected without your battery. Put your battery in and it should flash.
cloud911208 said:
Even when i go into flash mode it doesn't work. It goes in flash mode while it searches then after a while the x10 leaves flash mode. Tbh I think its my cable though. Any idea where to get an official one that will ship to hawaii?
Click to expand...
Click to collapse
any mini usb cable should work. i use the cable from my bt device for my phone.
If the x10 goes out of flashmode, try to hold in the back button under the whole flashing progress.
cloud911208 said:
Even when i go into flash mode it doesn't work. It goes in flash mode while it searches then after a while the x10 leaves flash mode. Tbh I think its my cable though. Any idea where to get an official one that will ship to hawaii?
Click to expand...
Click to collapse
Any electronics store has the cables ranging from $5-$30 depending on what your looking for in quality.
Sent From My *Super Fly X10*
If I (or anyone for that matter!) help you, dont be afraid to press THANKS!
Well thanks for the help. I'm gonna try use it on a different computer and see if it still works. Wish me luck.

Phone still gets stuck in boot loop after flashing stock firmware

I have a TMobile/MetroPCS GS4 model SGH-M919N that got stuck in a boot loop last week. I was finally able to find working firmware last night and used Odin to flash. Once it got to PASS my phone automatically rebooted with the blue recovery boot text in the top left, but then it just went back into a boot loop. I tried all other firmwares and none of them got to 100% so now I don't know what else I can do.
I have the same issue on a GT-i9505. I was using my phone this evening when it randomly rebooted and just keep rebooting until I removed my battery. After that, it was dead . Flashing stock firmwares like shooting a minigun and nothing works. Smells like a hard brick?
alesu69 said:
I have the same issue on a GT-i9505. I was using my phone this evening when it randomly rebooted and just keep rebooting until I removed my battery. After that, it was dead . Flashing stock firmwares like shooting a minigun and nothing works. Smells like a hard brick?
Click to expand...
Click to collapse
Have you tried replacing the battery? I figured I would try that but I havent gotten around to it yet
Not yet, i have no spare battery. Looks like when i plug the charger my phone just vibrates, like it's rebooting, and it's not showing anything. I found a similar issue here: http://forum.xda-developers.com/showthread.php?t=2532447
Looks like one guy did solve his problem.
*need to mention that by dead I mean it shows the "Samsung Galaxy S4 GT-I9505" logo and also shows "RECOVERY BOOTING", even though I didn't enter in recovery mode. Looks like now it doesn't shows anymore "RECOVERY BOOTING", but still, it doesn't boot. I was able to flash firmwares via odin and kies, but still no luck.
LE: It start booting by.. magic, i got to samsung boot logo, but that's all, crashed again.
After flash with Odin, immediately boot into recovery, perform a factory wipe, and reboot.
The problem is it doesn't boot into recovery.
LE: I managed to flash twrp via odin and boot into recovery, but i have an error:
"Unable to mount /data"
Any ideas?
LE2: Everything is useless, i managed to flash the rom, manage to boot into the rom, but then it will still reboot (which it did). Next step will be maybe to disassemble and clean all contacts.
alesu69 said:
The problem is it doesn't boot into recovery.
LE: I managed to flash twrp via odin and boot into recovery, but i have an error:
"Unable to mount /data"
Any ideas?
LE2: Everything is useless, i managed to flash the rom, manage to boot into the rom, but then it will still reboot (which it did). Next step will be maybe to disassemble and clean all contacts.
Click to expand...
Click to collapse
How did you manage to get into recovery?
harary said:
How did you manage to get into recovery?
Click to expand...
Click to collapse
Yes, but if I leave my phone in recovery (stock or custom), it just either freezes, either reboots, even though i don't do anything, just let it idle.
I can't manage to boot into the ROM 'cause eventually it will reboot. I couldn't finish the setup wizard.
OK so I don't know if this helps, but I managed to at least get past the "blue recovery boot" part. When the phone vibrated I let go of the power while still holding home + vol up, and I managed to get to the android guy with a blue progress bar below him. My phone shut off as the progress bar got 80-90% but now I know it's not impossible to start recovery.
Well, nothing works. After flashing pit file, an 4.4.2 odin prerooted image from here, cf auto root and then twrp, it will still randomly reboot. I manage to get past the boot logo into setup wizard, but phone just freezes after a couple of minutes, can't finish the setup wizard. Also, if i idle in twrp it will reboot sooner or later, tested already.I left my phone idling in twrp just to recharge my battery.
At least i have no more "unable to mount /data" errors.
I finally got it to work, all I had to do is keep flashing twrp and stock firmware back and forth. But it is just one problem after another with this thing, the problem now is every 5 minutes it will freeze and restart, also it tells me there is no sim even though it worked the first time i put it back in.
Operation Ivy said:
I finally got it to work, all I had to do is keep flashing twrp and stock firmware back and forth. But it is just one problem after another with this thing, the problem now is every 5 minutes it will freeze and restart, also it tells me there is no sim even though it worked the first time i put it back in.
Click to expand...
Click to collapse
What do you mean with back and forth?
harary said:
What do you mean with back and forth?
Click to expand...
Click to collapse
It means he flahsed and reflashed many times until he got lucky and it worked. That's what happened to me also. But i have the same issue, phone reboots or freezez after a couple of minutes, even though everything else is installed properly.
Dude, we have the same issue. Btw, is this happening to you too? Like, now and then when the phone freezes, that the screen is turning to a bright yellowish green?
I know a friend who repairs phone hardwares for a living, i gave it to him, i'll let you know how this went.
alesu69 said:
It means he flahsed and reflashed many times until he got lucky and it worked. That's what happened to me also. But i have the same issue, phone reboots or freezez after a couple of minutes, even though everything else is installed properly.
Dude, we have the same issue. Btw, is this happening to you too? Like, now and then when the phone freezes, that the screen is turning to a bright yellowish green?
I know a friend which repairs phone hardwares for a living, i gave it to him, i'll let you know how this went.
Click to expand...
Click to collapse
I got several times into Recovery Mode now, flashed several ROMs. I had no issues with freezing, especially not in TWRP Recovery Mode. But sometimes if i am trying to go into Recovery Mode or i just want to start ROMs, the screen turns into yellow behind the Samsung logo. If i dont take out the battery this wents into a complete white, but nothing happens.
Yes please tell if you got some news..
guys its not hard bricked its a problem wiht your power button
my friend had the same issue and then i killed the battery by letting it keeep bootlooping
then plugged it in and let it charge to around 10% and booted it
just try to press the power button slowly
Joashrox said:
guys its not hard bricked its a problem wiht your power button
my friend had the same issue and then i killed the battery by letting it keeep bootlooping
then plugged it in and let it charge to around 10% and booted it
just try to press the power button slowly
Click to expand...
Click to collapse
But it is sure that the power button is working because i get this blue "recovery booting". Or am i wrong?
So.... bad news, the guy whom i gave the phone to said that it's a short on the motherboard and there's nothing he can't do other than changing the motherboard. If you guys found another solution and that guy is mistaking, let me know.
alesu69 said:
So.... bad news, the guy whom i gave the phone to said that it's a short on the motherboard and there's nothing he can't do other than changing the motherboard. If you guys found another solution and that guy is mistaking, let me know.
Click to expand...
Click to collapse
Replace power button to new one. I have the same problems with s3 and this works. Try it.
Sent from my GT-I9300 using XDA-Developers mobile app
My phone is dead, it's not even charging anymore. The guy whom I give it to said it's a short on the motherboard. You guys managed to solve something with your phones? Or still a dead end?
alesu69 said:
My phone is dead, it's not even charging anymore. The guy whom I give it to said it's a short on the motherboard. You guys managed to solve something with your phones? Or still a dead end?
Click to expand...
Click to collapse
If You can't charge phone... Yup, motherboard is died. If You plug the charger and see something this have to be button but if You plug charger and don't see anything this is motherboard.

Trying to reload is on one plus 5.

My phone decided to hide in my pocket one day while I went swimming. Actually I forgot it was there. 30 minutes later I realize it's there and get it out of the water. I turn it off immediately. Take it to a drying station. When I get it back it turned on for a bit, then shut back down and went into a boot loop. So I restarted it into recovery mode and tried to reload the is, but my boot loader is locked.
My main question is,
How can I unlock the boot loader through the recovery menu. Adb won't do anything until that's done. I've tried Google, I've also read through the first couple pages on here.
I forgot to mention, I did send it back in to oneplus to see what they could do, they told me I'd need 5 or 6 new parts due to water damage. I wonder if I never told them it was water damaged, if they'd still come to that conclusion. The phone boots into recovery. I can navigate through the menus.
cfoster16 said:
My phone decided to hide in my pocket one day while I went swimming. Actually I forgot it was there. 30 minutes later I realize it's there and get it out of the water. I turn it off immediately. Take it to a drying station. When I get it back it turned on for a bit, then shut back down and went into a boot loop. So I restarted it into recovery mode and tried to reload the is, but my boot loader is locked.
My main question is,
How can I unlock the boot loader through the recovery menu. Adb won't do anything until that's done. I've tried Google, I've also read through the first couple pages on here.
I forgot to mention, I did send it back in to oneplus to see what they could do, they told me I'd need 5 or 6 new parts due to water damage. I wonder if I never told them it was water damaged, if they'd still come to that conclusion. The phone boots into recovery. I can navigate through the menus.
Click to expand...
Click to collapse
Water damage can easily indicated when opening the device cause there are indicators like stickers that will be changing color to read when they come in contact with extreme moisture or water.
There's nothing you can do until they repaired the parts.
What help do you want now, it's to late imo
Thank you for the reply. I have the phone back un-repaired. It's still in a boot loop and I can still boot o recovery and see it in adb, but it won't transfer the files with the bootloader locked.
The help I'm asking for is, is there a way to unlock the boot loader without an OS being on the phone? if so, how?
cfoster16 said:
Thank you for the reply. I have the phone back un-repaired. It's still in a boot loop and I can still boot o recovery and see it in adb, but it won't transfer the files with the bootloader locked.
The help I'm asking for is, is there a way to unlock the boot loader without an OS being on the phone? if so, how?
Click to expand...
Click to collapse
Not possible. You need to allow oem unlock.
You could try this:
https://www.google.ca/amp/s/forum.x...uide-unbrick-guide-hard-bricked-t3761706/amp/
It should work for almost any state. I haven't had the need to use it yet, but let me know if it works for you.
Cheers! ?

HELP! Black screen Bricked

I'm stuck on black screen and i can't even access fastboot , the phone do nothing at all
i was flashing DAVINCI_V11.0.2.0.QFJCNXM_f6f375d6c4_10.0 but it didn't boot it opens miui bootloader as if it's locked
then i tried flashing stock rom again davinci_global_images_V11.0.1.0.PFJMIXM_20191028.0000.00_9.0_global but laptop turns off due to low battery while flashing i tried to reboot the phone an then i got stuck on that black screen
anyone can help ?
Number one rule - charge battery and plug power supply before flashing. I think you have no option but to go to the repair shop - a special hardware must be used almost for sure as you damaged partitions
ahmedbadr00 said:
I'm stuck on black screen and i can't even access fastboot , the phone do nothing at all
i was flashing DAVINCI_V11.0.2.0.QFJCNXM_f6f375d6c4_10.0 but it didn't boot it opens miui bootloader as if it's locked
then i tried flashing stock rom again davinci_global_images_V11.0.1.0.PFJMIXM_20191028.0000.00_9.0_global but laptop turns off due to low battery while flashing i tried to reboot the phone an then i got stuck on that black screen
anyone can help ?
Click to expand...
Click to collapse
If you can't access even fastboot there is nothing you can do.
yaro666 said:
Number one rule - charge battery and plug power supply before flashing. I think you have no option but to go to the repair shop - a special hardware must be used almost for sure as you damaged partitions
Click to expand...
Click to collapse
it was an accident actually ,it was plugged in the laptop but the other end somehow got plugged out from the power brick

Categories

Resources