Hi everyone.
For years I've been coming here finding answers to problems that I've had. It seems I'm finally special enough to have to make a new thread.
Phone: S4 Gt-I9505
Carrier: Vodafone New Zealand
I rooted my phone with cf-autoroot and CWM on the stock 4.2.2 version of android. I then went looking for ROMs and found the leaked (didn't know it was at the time) 4.3 version from google. I installed that and whoopee! We got along well for the first two days, but I restarted my phone on day three and that's where the problem started.
Upon reboot, my phone powered onto the Samsung splash screen, but went no further. Confused, I did a factory recovery in CWM and it still didn't go. I reinstalled the rom and it went again fine, until reboot when it hung on the splash screen again. I tried various roms and fixes and just made a mess of my phone.
Long story short, I now have TWRP on my phone with the abyss 1.3.1F kernel installed and no ROM. Is there any step by step process that someone could give me on how to proceed with TWRP and which ROM/kernel to install to get me up and running again? Not fussy on which rom but one with no bloatware would be excellent. I would be eternally grateful! :fingers-crossed:
Thanks!
Download the latest version which is I9505XXUBMGA either Odin or CWM from here, if you flash via Recovery you need to wipe data & factory reset, cache partition and dalvik cache before flashing but you can flash via Odin
I prefer to use Philz Touch recovery than TWRP
Crauze said:
Download the latest version which is I9505XXUBMGA either Odin or CWM from here, if you flash via Recovery you need to wipe data & factory reset, cache partition and dalvik cache before flashing but you can flash via Odin
I prefer to use Philz Touch recovery than TWRP
Click to expand...
Click to collapse
Thank you Crauze, Will try now.
EDIT: That rom is going to take ages to download. I'll update when it's done in a few hours.
Crauze said:
Download the latest version which is I9505XXUBMGA either Odin or CWM from here, if you flash via Recovery you need to wipe data & factory reset, cache partition and dalvik cache before flashing but you can flash via Odin
Click to expand...
Click to collapse
Hi, you have touched on an issue I am trying to understand.
Do you only need to wipe you data and caches when you used custom recovery to flash a ROM but not when you use Odin on a PC?
Sent from my GT-I9505 using xda app-developers app
The above answer worked perfectly. Thank you!
jcodde said:
Hi, you have touched on an issue I am trying to understand.
Do you only need to wipe you data and caches when you used custom recovery to flash a ROM but not when you use Odin on a PC?
Sent from my GT-I9505 using xda app-developers app
Click to expand...
Click to collapse
I haven't flashed a custom ROM via Odin before but boot into Recovery and wipe data & factory reset, cache partition and dalvik cache and power off device and boot into Download Mode and flash via Odin
I dunno what went wrong here...
1) I have GT-I9505 (SSN: -I9505GSMH). I installed Galaxy S4 toolkit
2) Reboot into download mode. Used toolkit/Odin to root phone. Boots up. See SU.
3) Reboot into download mode. Used toolkit/Odin. Flashed TWRP Recovery
4) Phone boots up normal. Reboot into TWRP recovery. Did a factory Reset. Format.
5) Installed Zip (Latest Omega 9.0 ROM), unchecked the things I didn't want to install. Completed install, no errors reported. Rebooted.
6) Phone stuck on Samsung boot screen. I left it overnight thinking sometimes it may take 15 mins to boot system after new install.
7) Woke up, battery dead. Tried to charge phone. No charging indicators when plugged in. With whatever juice I had left I booted into TWRP recovery, it starts to charge again as I see the % batter increase after 5 mins.
-=-=-=-=- Did the Following to try to repair
a) Reinstalled Omega, this time leaving alll options on. Rebooted, stuck in Samsung boot
b) Flashed Phil CWM touch recovery, did complete wipe to install new ROM. Rebooted into Phil recovery. Flashed OMEGA. Reboot, stuck in Samsung boot.
c) Rebooted into Phil recovery, installed echo ROM, rebooted. Black screen. Rebooted into Phil. This time cannot get into recovery.
d) Started panicking, used Odin flashed TWRP. Would not flash. Something displayed about PIT error. Flashed Phil again. Reboot into recovery, WORKS! (recovery only). Went back into Download mode flashed TWRP. Rebooted, also WORKS!. Did a factory wipe. During wipe there was an error. Format, factory reset, error during wipe. Flashed OMEGA. Reboot. Stuck on samsung boot loop.
e) Downloaded official Samsung kernal for i9505 thinking it was the full flash rom. Flashed with ODIN (hoping to put everything back to factory). Completed flash, phone boots. I get OMEGA ANIMATION!!! Waited for 15 mins. Stuck on Animation. Reflashed TWRP. Rebooted, installed OMEGA...again. Stuck on samsung boot screen.
-=-=-= Kinda frustrated. What did I do wrong in the beginning?
There are so many official roms for the S4 based on region. What can I do to put it back to factory again? I purchased phone in Australia @ Samsung store. I figured download the Australia ROM but there are like 5 of them 4 being network branded roms I think. THe other one XSA is unbranded?
I tried searching for help but so far nothing works.
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
arnob_xperia said:
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
Click to expand...
Click to collapse
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
kabloomz said:
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
Click to expand...
Click to collapse
first use CWM or TWRP or whatever you want and format everthing
flash a fresh firmware(latest i prefer)
then flash stock recovery via odin of the built version what v9 was used, simply reboot to recovery and it will say MULTI CSC APPLIED from fresh frimware you used
then flash TWRP/CWM and flash v9
again simply reboot to recovery and it will say MULTI CSC APPLIED from V9
it will reboot, you must need to apply CSC to boot your phone
I can confirm this!
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
douglascamata said:
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
Click to expand...
Click to collapse
thats right stock recovery boot is needed to apply CSC
problem
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
Do you have an IMEI showing on your phone? What recovery did you use to flash Omega?
It matters, because some recoveries will screw it up.
Do you try to install with Philz recovery?
Sent from my GT-I9505 using xda premium
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
wifi problem
kabloomz said:
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
Click to expand...
Click to collapse
I did flash the Omega v9.1 and applied the wifi fix but the wifi is still broken. I tried unrooting it by flashing the original rom and formatting the data but the wifi is still broken. I can't turn it on. Thanks for the instructions anyways. ))
no pit partition
also, when i tried to root it again, it fails and says there is no PIT partition..
Where is the csc in TWRP so I can so what ones on the phone..??
What stock firmware can I use for a Orange Network in the UK.
GT-i9505 stuck on boot when upgraded from omega v16 to v21
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
BizK1d said:
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
Click to expand...
Click to collapse
Hi, I am having the same problem. First I installed the new firmware (NA5) and modem, tested it with the Omega ROM v21 and boot caught on so now tested the rom Fox Hound 4.1 and am having the same problem.
Kies tested this option but have not had the same luck as you. = /
Anyone know the reason? The rom Google Edition Jamal runs on my phone.
i9505
Hi guys,
I'm having a weird problem. I've used a i9100 and i9300 in the past and have flashed hundreds of different ROMs, kernels and recoveries. I was running WanamLite on my i9505 until I wanted to switch to PAC Alpha 4.3. I had a few problems installing it (didn't want to go past the boot logo) but eventually with TWRP it worked. I wasn't too happy with the alpha version (freezes here and there) and switched to Omega 9 4.2.2. Installed Xposed framework, rebooted and got stuck on boot. I couldn't access the recovery immediately, first I had to remove the battery, wait and after a few tries I was in the recovery. Removing Xposed framework, wiping data, cache, dalvik cache didn't help Omega 9 to boot up. I re-installed Omega 9 and did a restart without installing Xposed framework, and it froze on boot. Same thing happened when I installed WanamLite, Echoe and Google Experience ROMs and did a restart after the successful first boot after installation.
The only way to get past this problem is to:
a) flash the pre-rooted, original Samsung MGA ROM
b) enter recovery and wipe data/factory reset
If I skip b) then it will just enter a boot loop (boot halfway, reset, boot halfway, reset...)
It's driving me crazy. I do not want to use the original ROM and have no idea what is causing this behavior. I appreciate your help.
Here the information of the working MGA ROM:
4.2.2
I9505XXUBMGA
3.4.0-1081224
[email protected] #1
JDQ39.I9505XXUBMGA
ifonuser78 said:
Hi guys,
I'm having a weird problem. I've used a i9100 and i9300 in the past and have flashed hundreds of different ROMs, kernels and recoveries. I was running WanamLite on my i9505 until I wanted to switch to PAC Alpha 4.3. I had a few problems installing it (didn't want to go past the boot logo) but eventually with TWRP it worked. I wasn't too happy with the alpha version (freezes here and there) and switched to Omega 9 4.2.2. Installed Xposed framework, rebooted and got stuck on boot. I couldn't access the recovery immediately, first I had to remove the battery, wait and after a few tries I was in the recovery. Removing Xposed framework, wiping data, cache, dalvik cache didn't help Omega 9 to boot up. I re-installed Omega 9 and did a restart without installing Xposed framework, and it froze on boot. Same thing happened when I installed WanamLite, Echoe and Google Experience ROMs and did a restart after the successful first boot after installation.
The only way to get past this problem is to:
a) flash the pre-rooted, original Samsung MGA ROM
b) enter recovery and wipe data/factory reset
If I skip b) then it will just enter a boot loop (boot halfway, reset, boot halfway, reset...)
It's driving me crazy. I do not want to use the original ROM and have no idea what is causing this behavior. I appreciate your help.
Here the information of the working MGA ROM:
4.2.2
I9505XXUBMGA
3.4.0-1081224
[email protected] #1
JDQ39.I9505XXUBMGA
Click to expand...
Click to collapse
This happens with many including me some time with many diffrnt files chainging and overwriting causes the same
Best option as u said above flash stock firmware
Then u can try what I feel will work better in ur case
Root the phone with CF root method
Flash Philz Recovery
wipe cache / dalvik / ix perm and reboot and go ahead with ur Rom flashing
Ok, flashed the stock ROM which was not rooted, then rooted using CF's method and flashed PhilZ. I couldn't find the option to fix permissions in PhilZ recovery, and went ahead with the installation of Omega 9 after wiping. I couldn't even get Omega to boot, previously it worked on the first boot and then no longer after a restart.
I don't know whats going on here.
I'm flashing the pre-rooted MGA now.
ifonuser78 said:
I'm flashing the pre-rooted MGA now.
Click to expand...
Click to collapse
Pre-rooted MGA works fine, but no other custom ROM.
I ran TriangleAway to reset the counter, but that didn't help either. No third party custom ROMs for me. :crying:
Flash latest Philz recovery.
Go to mounts and storage.
MAKE SURE YOU HAVE A ROM ON SD CARD.
Format system, cache, data and preload.
then just to be sure everything is gone I go to wipe /data factory reset and choose the wipe to install a new rom.
Then go to install zip and flash rom.
Once it's flashed you should be good to reboot.
If you're still in a bootloop then go to wipe/data factory reset but choose first option not the one to install rom.
Now reboot again, good to go!
Just a thought, if you're still having trouble flash a AOSP kernel in Philz as you might be trying to boot an AOSP rom with a TW kernel installed
Sent from my GT-I9505 using XDA Premium HD app
•Please take time to read•
So first, I changed into cyanogenmod, it was successful though my sister didn't liked its "style" so I had to restore the stock firmware of jellybean 4.3 (XXUEMJ5_I9505OLBEMJ5_I9505XXUEMJ5_HOME.tar.md5) so i did a factory reset from the cyanogenmod settings and then flashed(it said my root access was lost after factory reset) using ODIN, everything went fine in the process in flashing, after my s4 reset 1st time a droid with a spinning thing on its tummy appears with the loading bar on its bottom and then resets once again I thought it was already good but my s4 was stuck on the SAMSUNG logo the blinking one. And then I downloaded a new stockrom the 4.2.2 (I9505XXUBMG5_I9505OLBBMG1_I9505DXUBMG5_HOME.tar and which was my original firmware the XXUBMG5), tried to flash using ODIN but it failed during the process, I'm about to download a new copy of the 4.2.2 version from the same site i downloaded from maybe it was corrupt?. Please help, me and my friend have done all things like using KIES that doesn't recognize my phone anymore, downloading stock recovery and such non works and so does my recovery mode after I access it, my s4 i9505 immediately restarts by itself after releasing my fingers and a lot of battery pulls. No luck please help me. I'm from the Philippines with an unlocked phone, International so I downloaded the XTE Region correct me if I'm wrong .
Please provide instructions if you have time .
After installation you have done this in the recovery mode wipe data factory reset and wipe cache partition
(can try with custom recovery - wipe and flash again)
Adnan73 said:
After installation you have done this in the recovery mode wipe data factory reset and wipe cache partition
(can try with custom recovery - wipe and flash again)
Click to expand...
Click to collapse
Thank you very much ))))))) now it's working again, I forgot that entering recovery mode takes a while now my depression is lot ahahha
Hi Guys
OK so I am sure I am having a massive blonde moment here as I have installed custom roms to my phones and tablets many times but any insight would be greatly appreciated, feel free to call me an idiot when you point out the obvious . Everytime I flash C-Rom from CWM I get stuck on the Galaxy S4 initial boot screen.
Phone Details
GT-I9505 (Australia - Telstra)
PDA: I9505XXUEND1
CSC: I9505TELENC1
Modem: I9505XXUEND1
Android 4.3
Stock Firmware
Stock Kernel
CWM Recovery
Rooted (First was Knox safe rooted then tried manually rooted and SuperSU disabling Knox)
Edit: before anyone asks yes I formatted data, did a CWM wipe data, wipe cache and wipe dalvik cache.
Edit2: CM11 + KT kernel flashes and boots fine but as soon as I flash C-Rom and KT it get stuck on the boot logo
Thanks
XxInvictus
Bumpity bump, can anyone help?
Sent from my GT-I9505 using Tapatalk
Am I understanding you correctly that you flash C-rom and KT kernel? What happens when you only flash C-rom?
Did you try a different recovery? Like TWRP?
I have tried it just by itself, I only really installed KT Kernel after I was running out of ideas, haven't tried another recovery as others have had it work with CWM but I have tried more than one version of CWM
Sent from my GT-I9505 using Tapatalk
And as I predicted stupid mistake, used HashCalc, the rom download was corrupt, redownloaded and all OK.
OP = Idiot
Thanks anyway for attempting to help Lennyz