Has anyone with atmel digitizer changed it with the synaptics one and if it worked? My front cover is cracked so im thinking of buying a new one digitizer with the front glass. But most of them are synaptics and i have heard synaptics respond better (my atmel lagged sometimes on lockscreen). So has anyone with atmel bought a synaptics one and if yes did it worked?
i m wondering that too
Someone told me they tried it and it worked. I think it was Blefish
Sent from my Desire HD using Tapatalk 2
im just curious if a reinstallation of the official rom is required after going from atmel to synaptics in order the right synaptics drivers to be installed as its a new hardware found
As the kernel includes both touch screen drivers, you can simply switch them out and it will work. No software modifications are needed.
I switched mine from Synaptics to Atmel and went well.
Blefish said:
As the kernel includes both touch screen drivers, you can simply switch them out and it will work. No software modifications are needed.
I switched mine from Synaptics to Atmel and went well.
Click to expand...
Click to collapse
so you saw difference between Atmel and Synaptics?.I don't think there are many users who have tried both so you can share your experience..!
korekore1 said:
so you saw difference between Atmel and Synaptics?.I don't think there are many users who have tried both so you can share your experience..!
Click to expand...
Click to collapse
Well, first the Atmel driver from Huawei is horrible. Luckily that's already covered by me and included in my upcoming ROM. Secondly, Atmel supports up to 10 fingers with my driver. Atmel is highly configurable, all the thresholds are modifiable so we can improve it greatly.
In hardware side, I could say the button brightness is lower and more blueish on Atmel, but that could be just me.
so if I wanna buy a synaptics one how should I order? as far as I remember they had different cable/bus colors
Blefish said:
Well, first the Atmel driver from Huawei is horrible. Luckily that's already covered by me and included in my upcoming ROM. Secondly, Atmel supports up to 10 fingers with my driver. Atmel is highly configurable, all the thresholds are modifiable so we can improve it greatly.
In hardware side, I could say the button brightness is lower and more blueish on Atmel, but that could be just me.
Click to expand...
Click to collapse
Ι'm on atmel too but i have u8800pro.Any chance your drivers can be installed in pro?
JaymzBond said:
so if I wanna buy a synaptics one how should I order? as far as I remember they had different cable/bus colors
Click to expand...
Click to collapse
Me too, do I buy the gold or black cables. Which is atmel?
Sent from the hands of my Impulse 4g.
Somcom3X said:
Me too, do I buy the gold or black cables. Which is atmel?
Sent from the hands of my Impulse 4g.
Click to expand...
Click to collapse
I bought mine from eBay and it had a listing where they offered both golden and black cable color.
So:
* Golden cable - Atmel mXT224
* Black cable - Synaptics TM-1564
Synaptics has a note on it with TM-1564 and on the cable you can see Synaptics aswell. Atmel has a Truly sign on it.
Blefish said:
I bought mine from eBay and it had a listing where they offered both golden and black cable color.
So:
* Golden cable - Atmel mXT224
* Black cable - Synaptics TM-1564
Synaptics has a note on it with TM-1564 and on the cable you can see Synaptics aswell. Atmel has a Truly sign on it.
Click to expand...
Click to collapse
what about your drivers?!can they be used on pro?
korekore1 said:
what about your drivers?!can they be used on pro?
Click to expand...
Click to collapse
If a developer adds it into one of the kernels for U8800+, yeah.
Blefish said:
If a developer adds it into one of the kernels for U8800+, yeah.
Click to expand...
Click to collapse
Which do you reccomend? I'm afraid this wont work on the stock 2.2
Sent from the hands of my Impulse 4g.
Blefish said:
Well, first the Atmel driver from Huawei is horrible. Luckily that's already covered by me and included in my upcoming ROM. Secondly, Atmel supports up to 10 fingers with my driver. Atmel is highly configurable, all the thresholds are modifiable so we can improve it greatly.
In hardware side, I could say the button brightness is lower and more blueish on Atmel, but that could be just me.
Click to expand...
Click to collapse
Up to 10 fingers? Dafuq I can only use 2 -.-, how can I increase the value?
Sent from my U8800 using xda app-developers app
nikeradsn said:
Up to 10 fingers? Dafuq I can only use 2 -.-, how can I increase the value?
Sent from my U8800 using xda app-developers app
Click to expand...
Click to collapse
With my driver I mean. It is possible to do it on stock too, but that'd require rewriting the report code, because as said, Huawei's driver sucks.
Sent from my U8800
Blefish said:
With my driver I mean. It is possible to do it on stock too, but that'd require rewriting the report code, because as said, Huawei's driver sucks.
Sent from my U8800
Click to expand...
Click to collapse
There is no source code, its a special stock.
Sent from my U8800Pro using Tapatalk 2
Is it possible to do it on dzo's aurora?
Sent from my U8800 using xda app-developers app
Here's the comparison pictures, Synaptics is on the left on all the pictures. Please ignore the Atmel glue marks, that's how I glued it on my old frame.
When buying with a frame, please also note the speaker size, they are not compatible with each other, at least that's what I've heard of.
Blefish said:
Here's the comparison pictures, Synaptics is on the left on all the pictures. Please ignore the Atmel glue marks, that's how I glued it on my old frame.
When buying with a frame, please also note the speaker size, they are not compatible with each other, at least that's what I've heard of.
Click to expand...
Click to collapse
How can i notice the speaker size, my touch screen was broken and i have a plan for replacement but i'm not sure i will buy the right one.
Related
Did anyone here notice problems with multi-touch when pressing with 4 fingers in a square.
It fails to recognize all fingers or misplaces them or other strange behaviour.
That means the screen is not REAL multi-touch and that's kinda disappointing in my opinion.
(4 fingers work fine in most situations, only when trying to achieve a perfectly aligned square)
Can anyone else try this? (best program to use is "Multitouch visible test" free from market.)
Works for me.
Sent from my Motorola Startac running Atari 2600 software!
if there are 2 fingers on same row, one of them disapere.. if you do a perfect square, you get left with one finger working...
DubelBoom said:
if there are 2 fingers on same row, one of them disapere.. if you do a perfect square, you get left with one finger working...
Click to expand...
Click to collapse
As I said, strange stuff happens with 4 fingers aligned like that
Foladko said:
As I said, strange stuff happens with 4 fingers aligned like that
Click to expand...
Click to collapse
very wired.... but how cares, i can play fruit ninja with 4 fingers
I am having no problems at all...
Sent from my Desire HD using XDA Premium App
Works for me....
And yes, it is "real" multitouch
Fine here too.
All good with mine also - four points in a square with no problems whatsoever.
works fine with me too
I've been testing this further today and it's slightly more complicated.
I noticed that when plugged into charger it seems to work, but as soon as I disconnect it the issue is back.
It also worked or didn't randomly through the day.
So I guess this could be a software issue, possibly to conserve battery..?
Foladko said:
I've been testing this further today and it's slightly more complicated.
I noticed that when plugged into charger it seems to work, but as soon as I disconnect it the issue is back.
It also worked or didn't randomly through the day.
So I guess this could be a software issue, possibly to conserve battery..?
Click to expand...
Click to collapse
I noticed this too! At first, I was happy that it worked for me, but then I read this, and plugged it out of the charger. So then we know that when we want to impress our friends with four points multitouch, we need to have the charger plugged in
Foladko said:
I've been testing this further today and it's slightly more complicated.
I noticed that when plugged into charger it seems to work, but as soon as I disconnect it the issue is back.
It also worked or didn't randomly through the day.
So I guess this could be a software issue, possibly to conserve battery..?
Click to expand...
Click to collapse
I can confirm that. Just tried it and it behaves very strange. Seems to me that it's not related to charging because both times I had my phone off the charger...
EDIT: OK I rebooted just to see if it's software related. It's not. It's purely hardware. You have to hold your phone to get proper multitouch. Simple as that.
Sent from my Desire HD using XDA App
DubelBoom said:
if there are 2 fingers on same row, one of them disapere.. if you do a perfect square, you get left with one finger working...
Click to expand...
Click to collapse
You might have a faulty device if it doesn't work...
Sent from my Desire HD using XDA Premium App
Please remember that there are 4 different models of touch panel that HTC use in the Desire HD, 2 different screen models and 2 different camera modules. Not all DHDs are the same. If you have an ENG HBoot then you can see what hardware your DHD has by checking 'system info'.
Doktaphex said:
Please remember that there are 4 different models of touch panel that HTC use in the Desire HD, 2 different screen models and 2 different camera modules. Not all DHDs are the same. If you have an ENG HBoot then you can see what hardware your DHD has by checking 'system info'.
Click to expand...
Click to collapse
Well I know about 2 different screens, and the Inspire 4G uses a slightly better camera, but I've never heard about 4 different touch panels being used
I also don't think it's a hardware issue, because then it wouldn't just work and then stop randomly. It really sounds like a software thing TBH
My phone has the auo screen and the touch pannel is: SYN3KT_0108
Foladko said:
Well I know about 2 different screens, and the Inspire 4G uses a slightly better camera, but I've never heard about 4 different touch panels being used
I also don't think it's a hardware issue, because then it wouldn't just work and then stop randomly. It really sounds like a software thing TBH
My phone has the auo screen and the touch pannel is: SYN3KT_0108
Click to expand...
Click to collapse
Hold the phone while testing the touchscreen. if you just leave it on the table, it behaves like you describe. If you hold it in your hand, the touches are precise.
Foladko said:
Did anyone here notice problems with multi-touch when pressing with 4 fingers in a square.
It fails to recognize all fingers or misplaces them or other strange behaviour.
That means the screen is not REAL multi-touch and that's kinda disappointing in my opinion.
(4 fingers work fine in most situations, only when trying to achieve a perfectly aligned square)
Can anyone else try this? (best program to use is "Multitouch visible test" free from market.)
Click to expand...
Click to collapse
If you get "Z-DeviceTest" app you can test almost everything... and our Display can recognize a maximum of 4 fingers, not more and not less, so its multitouch => Jazzhand XD^^
As others pointed out you need to hold the phone in your hand so your hand acts like a ground. And thats actually not really a problem since capacitive technology is supposed to be grounded if you want to make precise touch. Thats just basic electronic stuff we all should know
Sent from my Desire HD using XDA App
Nece228 said:
As others pointed out you need to hold the phone in your hand so your hand acts like a ground. And thats actually not really a problem since capacitive technology is supposed to be grounded if you want to make precise touch. Thats just basic electronic stuff we all should know
Sent from my Desire HD using XDA App
Click to expand...
Click to collapse
I have thought of that and I know how capacitive touch tech works.
That does make sense.
But then 4 touch shouldn't work at all when not plugged in or being held, instead only square position not working when not in contact, I mean 4 fingers is the same deal whatever way you position them on the screen?
Care to explain further?
This question was triggered in regard to the folks out there (myself included) who have experienced cracked SCREENS in the early models. I'm curious, what is it about the design of the n7 LCD that causes all touch functionality to stop if a crack occurs? I remember seeing touch screen devices in the past with cracked screens that still responded to touch... Just made me wonder what made the n7 different. Then again maybe it's not so different and I just haven't come across anybody who had a touch-working cracked LCD... Any insight?
Sent from my Nexus 7 using xda app-developers app
JaSauders said:
This question was triggered in regard to the folks out there (myself included) who have experienced cracked SCREENS in the early models. I'm curious, what is it about the design of the n7 LCD that causes all touch functionality to stop if a crack occurs? I remember seeing touch screen devices in the past with cracked screens that still responded to touch... Just made me wonder what made the n7 different. Then again maybe it's not so different and I just haven't come across anybody who had a touch-working cracked LCD... Any insight?
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
according to my personal knowledge, the touch sensors are built into the display itself, or if you prefer, the glass. so if the glass does shatter, this is a fair chance that the touch sensor will be damaged.
Hello,
I broke the screen of my Moto Defy+ (MB526) which I obviously want to replace.
However, here (NL) we only have parts (such as replacement screens etc) for the Moto Defy (MB525) available.
Does anybody know if hardware parts such as screens/digitizers etc. are interchangeable between the MB525 and the MB526?
Thanks in advance,
TY
Although not absolutely certain, but I think they're identical with respect to the touch screen and hence parts should be swappable between models
Sent from my MB526 using xda premium
All the parts are interchangeable (caution with camera and battery) between defy and defy+.
Ignore of your taking about digitizer
I may be wrong but afaik display comes with rev versions so make sure its the same revision(may be written on the display itself
Sent from my MB526 using xda premium
OK
hackergnome said:
Ignore of your taking about digitizer
I may be wrong but afaik display comes with rev versions so make sure its the same revision(may be written on the display itself
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
Take care about battery and camera, all other parts are interchangeable, i think.
As far as display and digitizer goes its all the same Ive replaced mine manually with a chinese one. Works fine. Remember your speaker orientation before popping it out. Might not matter but why risk it and it looks identical rotated.
drawkcaB said:
As far as display and digitizer goes its all the same Ive replaced mine manually with a chinese one. Works fine. Remember your speaker orientation before popping it out. Might not matter but why risk it and it looks identical rotated.
Click to expand...
Click to collapse
Slight bit of an OT regarding our Defy Screen.
Since you replaced yours with a Chinese replacement LCD, how's the quality of the display? Is it par with the original Defy LCD?
Though i always use the freezer trick to fix dead pixels on my Defy. I'm planning on also replacing my LCD with a Chinese one hoping that it will be more tough on dead pixels..
Thanks.
chipset used in defy+ is little different to that of the defy. Some Parts may cause problem
drawkcaB said:
As far as display and digitizer goes its all the same Ive replaced mine manually with a chinese one. Works fine. Remember your speaker orientation before popping it out. Might not matter but why risk it and it looks identical rotated.
Click to expand...
Click to collapse
Hey,
Can you confirm the quality of chinese LCDs? I am getting MB525 LCD, which I hope is compatible with MB526. My phone, got dropped from bed & not almost half of the screen is black.
I stay in Mumbai, India.
Tnx.
mGforCe said:
Hey,
Can you confirm the quality of chinese LCDs? I am getting MB525 LCD, which I hope is compatible with MB526. My phone, got dropped from bed & not almost half of the screen is black.
I stay in Mumbai, India.
Tnx.
Click to expand...
Click to collapse
Sorry been off XDA for ages. Yeah my Digitizer works fine. I didnt change the screen just the touch was cracked and i changed it along with the entire front housing. Works without any issues. I too live in mumbai and i ordered mine from ebay.com
u8800-51 touch screen bottom not responding
hi all
i am new and ignorant
(love the xda rules vid)
just bought second hand at&t impulse 4g (u8800-51) , with the bottom half of the screen, not responding to touch.
the top half works
i was told that it happened when the device got dropped.
the picture is good.
got stuck in at&t logo boot loop, and erased back to original on the android rescue screen. and its booting again
tried to reassemble the screen , but no change.
will replacing the glass plus digitizer solve it?
is there a difference between u8800 and u8800-51 screen parts? (or any other hardware for that matter?)
thanks alot
Switching the touch screen (glass) will fix your problem.
In which side do you have the notification led on? Right or left of speaker?
If it is on the right, you probably have the smaller speaker system (that's good to know if you are buying with the frame).
There is no difference in the sockets, however I have seen all Impulse 4G have the Synaptics version (black flex cable), so it would be better if you'd buy that. Some of the eBay sellers are offering the official AT&T touch screen, with the logo on it, so that would be a safe place to buy from.
-EDIT-
Some more things to know:
When they are selling with a frame, you can see it on the picture and they usually mention that somewhere too. If you took the phone open, it's easy to tell if it's big or small by looking whether it looks like this (big speaker).
Blefish said:
Switching the touch screen (glass) will fix your problem.
In which side do you have the notification led on? Right or left of speaker?
If it is on the right, you probably have the smaller speaker system (that's good to know if you are buying with the frame).
There is no difference in the sockets, however I have seen all Impulse 4G have the Synaptics version (black flex cable), so it would be better if you'd buy that. Some of the eBay sellers are offering the official AT&T touch screen, with the logo on it, so that would be a safe place to buy from.
-EDIT-
Some more things to know:
When they are selling with a frame, you can see it on the picture and they usually mention that somewhere too. If you took the phone open, it's easy to tell if it's big or small by looking whether it looks like
thank u so much
after a long study of the different pics of sellers, i remain a confused, because i finally found enough pics
(attached)
to realize that my model always have the black cable u mentioned which comes with a SMALL speaker, while the big speaker always come with the yellow cable, but alas, my device comes with a black cable, but big speaker,
so should i go with cable color + name mentioned (AT&T Impulse 4G) + AT&T logo, (which all calls for a Small speaker) OR , should i go with speaker size (big) ?
regarding my indicator position, it is to thr right when i look from the inner angle (like the photo of the big speaker that u added
Click to expand...
Click to collapse
That's the digitizer only. I don't think it's glass really, but it's easier to say it is.
I replaced mine by taking off the old digitizer from the frame. It came off pretty easily, it just needs some patience to take it apart without breaking it.
If you don't want to mess with glue, I'd suggest this: http://www.ebay.co.uk/itm/Digitizer...356?pt=LH_DefaultDomain_0&hash=item4abfc0011c
It's without the AT&T logo. I cannot guarantee it will fit though, there is always this chance Huawei modified something else between the U8800 and -51.
Blefish said:
That's the digitizer only. I don't think it's glass really, but it's easier to say it is.
I replaced mine by taking off the old digitizer from the frame. It came off pretty easily, it just needs some patience to take it apart without breaking it.
If you don't want to mess with glue, I'd suggest this: http://www.ebay.co.uk/itm/Digitizer...356?pt=LH_DefaultDomain_0&hash=item4abfc0011c
It's without the AT&T logo. I cannot guarantee it will fit though, there is always this chance Huawei modified something else between the U8800 and -51.
Click to expand...
Click to collapse
Takes over 15 days. I guess you can use adhesive tape to stick it.
http://pages.ebay.com/link/?nav=item.view&id=19075902577
Sent from my U8800-51
Dissenters tWellf
Somcom3X said:
Takes over 15 days. I guess you can use adhesive tape to stick it.
( linked reposting banned for me by the forum)
Sent from my U8800-51
Click to expand...
Click to collapse
thanks allot again
the Ebay links leads to:
"This listing (19075902577) has been removed, or this item is not available.
Please check that you've entered the correct item number
Listings that have ended 90 or more days ago will not be available for viewing."
???
Blefish said:
That's the digitizer only. I don't think it's glass really, but it's easier to say it is.
I replaced mine by taking off the old digitizer from the frame. It came off pretty easily, it just needs some patience to take it apart without breaking it.
If you don't want to mess with glue, I'd suggest this:
It's without the AT&T logo. I cannot guarantee it will fit though, there is always this chance Huawei modified something else between the U8800 and -51.
Click to expand...
Click to collapse
thanks Blefish
i prefer not to risk peeling, for breakage, and gluing, for moisture and mess.
i am starting to think that my digitizer was not original, and that is why it failed.
and feels like plastic. i found an original part at cellulardr.com for about 70$ vs. the 10-$15 ebay ones.
so maybe the seller put on impulse 4g, a big earpiece frame, with a yellow cable digitaizer. what a mess!
i attach a pic of big vs small earpieces. i believe the ''big'' is the one with golden terminals.
i think i will get a cheap ebay small earpiece frame with a black cable digitizer (like the original had, i believe) , with a 5$ small earpiece as extra.
god. why do i feel like Sherlock Holmes ?
http://pages.ebay.com/link/?nav=item.view&id=190759025771
This is only with glass.
You can buy a used one for under $70 or an OEM frame with glass. In my op, its not worth to fix.
(Oem->Original equipment manufacturer)
Sent from my U8800-51
Somcom3X said:
http://pages.ebay.com/link/?nav=item.view&id=190759025771
This is only with glass.
You can buy a used one for under $70 or an OEM frame with glass. In my op, its not worth to fix.
(Oem->Original equipment manufacturer)
Sent from my U8800-51
Click to expand...
Click to collapse
thanks
i am sorry - what is not worth fixing ?
yes, i am going to buy a small earpiese frame with black cable plus a small earpiece,
but seeing my old digitizer, i am starting to think (because of the price difference from the original) that all these E-bay so called "glass" , 10-15$ , advertized digitizers ,are actually made of plastic ??
but i will not "invest in an expensive glass before i am happy with the new device.
so far i have not seen used original digitizers.
if i am happy with the device, i might start looking for a"for parts" u8800-51 deal on E-bay
thanks again
hove64 said:
thanks
i am sorry - what is not worth fixing ?
yes, i am going to buy a small earpiese frame with black cable plus a small earpiece,
but seeing my old digitizer, i am starting to think (because of the price difference from the original) that all these E-bay so called "glass" , 10-15$ , advertized digitizers ,are actually made of plastic ??
but i will not "invest in an expensive glass before i am happy with the new device.
so far i have not seen used original digitizers.
if i am happy with the device, i might start looking for a"for parts" u8800-51 deal on E-bay
thanks again
Click to expand...
Click to collapse
The phone is not worth fixing.
Sent from my U8800-51
Somcom3X said:
The phone is not worth fixing.
Sent from my U8800-51
Click to expand...
Click to collapse
i am sorry....why not worth fixing ?
20$ plus a little more work and i have got a working smart phone - no ?
hove64 said:
i am sorry....why not worth fixing ?
20$ plus a little more work and i have got a working smart phone - no ?
Click to expand...
Click to collapse
Yes, but $70 and you have a brand new one. Basically, fixing it is more trouble than selling it.
Sent from my U8800-51
Somcom3X said:
Yes, but $70 and you have a brand new one. Basically, fixing it is more trouble than selling it.
Sent from my U8800-51
Click to expand...
Click to collapse
thanks
the cheapest new impulse 4g i could find cost 150$. i do get your point, but i already invested time and money on it and i can't sell a device that i am not sure of his condition. also its a little bit exciting for me if i manage to make it work.
is there any way to bypass the faulty touch screen ,for sake of testing the phone,
with some external device such as usb\Bluetooth mouse and keyboard ?
hove64 said:
is there any way to bypass the faulty touch screen ,for sake of testing the phone,
with some external device such as usb\Bluetooth mouse and keyboard ?
Click to expand...
Click to collapse
Recovery or adb commands
Sent from my U8800-51
Somcom3X said:
Recovery or adb commands
Sent from my U8800-51
Click to expand...
Click to collapse
thanks
i will check if adb can help
hi,
what is the advantage of buying this screen?
http://www.ebay.com/itm/New-Touch-S...e_Replacement_Parts_Tools&hash=item4d16e48a92
what are the risks?
or compensates more buy:
http://www.ebay.com/itm/Replacement...e_Replacement_Parts_Tools&hash=item5d43fc8537
The first one seems to be Synaptics, without the frame. It means you have to glue it to your old frame yourself. No need to worry about speaker size here, since it won't include one.
The seconds one seems to be Atmel with frame, but notice the big speaker. It must be compatible otherwise the speaker stops working (as far as I know U8800 ships with small speaker, but I can't be sure).
is easy to paste?
BS55 said:
is easy to paste?
Click to expand...
Click to collapse
It's not hard at all. You just need to be careful not to spill it on the touch screen visible part.
Getting the old touch screen off might take some time, as the cover is not that strong. I removed it slowly and it came off pretty well.
is there any tutorial?
BS55 said:
is there any tutorial?
Click to expand...
Click to collapse
How about this one?
ebay.com/itm/New-Touch-Screen-Digitizer-Huawei-U8800-Ideos-X5-AT-T-/280972093595
It' a little bit cheaper and looks the same as the first one, in the first post.
I'm having some problems with my touchscreen, where sometime it detects some inputs in the right area of the screen. It's truly annoying, as you my think....
I'm thinking about buying a new one.
Which one is better by the way, Synaptics or Atmel? I would like something cheap, but that don't work/feel garbage...
A video about the replacement steps: youtube.com/watch?v=CgtaBxR-6mk
PS: replace xx by tt in the links. sorry about that, forum restrictions.:silly:
Leinad112 said:
How about this one?
ebay.com/itm/New-Touch-Screen-Digitizer-Huawei-U8800-Ideos-X5-AT-T-/280972093595
It' a little bit cheaper and looks the same as the first one, in the first post.
I'm having some problems with my touchscreen, where sometime it detects some inputs in the right area of the screen. It's truly annoying, as you my think....
I'm thinking about buying a new one.
Which one is better by the way, Synaptics or Atmel? I would like something cheap, but that don't work/feel garbage...
A video about the replacement steps: youtube.com/watch?v=CgtaBxR-6mk
PS: replace xx by tt in the links. sorry about that, forum restrictions.:silly:
Click to expand...
Click to collapse
Synaptics is more or less ok, but Atmel is more configurable and with my ROM you get 10 point multitouch.
The video is nice, but it seems to describe the method where you have touch screen with the FRAME, so it does not involve replacing the actual digitizer. The eBay link offers just the digitizer, so an extra step is needed to replace the digitizer in the frame with the new one.
Blefish said:
Synaptics is more or less ok, but Atmel is more configurable and with my ROM you get 10 point multitouch.
The video is nice, but it seems to describe the method where you have touch screen with the FRAME, so it does not involve replacing the actual digitizer. The eBay link offers just the digitizer, so an extra step is needed to replace the digitizer in the frame with the new one.
Click to expand...
Click to collapse
I thought that the multitouch limit of 2 was an hardware thing! That is very good! I'm using your CM11, and I can only make 2 multitouch at a time. So, it's a Synaptics touch, right?
Aren't you going to change the driver in the next ROM, because of the problems turning the screen off/on?
Keep the good work on that.
So, the initial problems (2012) that the Atmel touch had, are gone?
About the video, there is really one steep missing. I'm a little worried about damaging the metalic frame arround the phone, to separate the "glass" from the frame. Maybe from the inside it's easier, i hope.
Thanks!