HI everybody, first i am from germany so excuse my english
i have a Herm 300 that belongs to a friend of mine, he just bricked his phone during a flash procedure.
It shows the same as in point 4 described here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
so i did that MTTY thing and after the reboot on the screen appears something like:
+
if u want to rest all date press QWERTY (R) for YES
and QWERTY (dunno that letteranymore) for no
so i pressed R for YEs and softresetted with stylus.
Now i cannot turn that device on, no led lids up nothing!
so i put the battery out an plugged in the chgarger cable
et voilá a red led lits up on the right corner.
i cannot turn the device on and when i put the battery back, the red led tunrs off.
Is here someone who can help me?
thanks!
Linus02
If you can get your hands on another battery then try that as the led lights up meaning that the hardware is still working. Battery could be bung...
Cheers...
but with a charger cable plugged in, it mustbe possible to start up the device or?
When i turn out battery from my 'HTc Touch and plug in charger, i can start the device but not the herm?
greets
Linus02
You can't start the Hermes without a good battery installed....
hey guy ,i don't know how to fix this.my wizard can't charge .any time i put it in to cradle i see on the battery is 0% and the red flashing light (it must always stay red on charge) if i pull the cradle out it'll shutdown and i have to restart it.any one help me to find out where's the damage and how can i get my xda back to normal. thanks for helping me!
fixing XDA mini
HI,
It sounds like the mini usb connector on the bottom of your XDA is suffering from bad solder joints. Only way to fix that is to open it up and re-solder them - not an easy job!
It is also possible that your battery has just had it - have you tried replacing it?
Regards,
John
yeap! i tried to replace it by another one but it doesn't work.( can not charge,no usb connections, no sync) i think the power chip ( that the way i call it cause' i do not know how to call it) was fail .Everything works well except the mini usb connector. describe it again : when i put the recharger into my wizard it says (" recharging..." "main battery 0%") in about 20 seconds .after that the recharge light start flashing, and if i disconnect the recharger my wizard will shutdown and i have to restart it again.
My Blackstone doesn't sync when connected to pc and also not charge either with charger or data cable Somebody plzzzzzzzzzzzz help me
:(
sakiyo6789 said:
My Blackstone doesn't sync when connected to pc and also not charge either with charger or data cable Somebody plzzzzzzzzzzzz help me
:(
Click to expand...
Click to collapse
had a similar issue which...i had to send my hd to htc, the mother baord was replaced,, make sure u turn bak to stock rom inorder for it to be under warranty
tc
Please check the following:
Unplug your device. Turn off (no standby, turn completely off by long-pressing the power button) your HD and start into bootloader mode (hold down the volume down key while pressing the power button). You should now see a screen with four coloured bars in the background (red, green, blue and white, if I'm correct). Wait a few seconds until it reads "serial" at the bottom. When it does, connect your HD to a USB port - if your USB port still works, it should switch from "serial" to "USB"! After connecting, wait a few seconds as the PC might install some drivers first...
If it doesn't switch to "USB" I would guess that your device has a hardware fault...
Good luck! Crossing my fingers!
thank yu for yours suggestion but my phone is not under warranty now and i have given all my pained earnings to purchase this ppc c and also my rom is not the original one so can anyone show me a simple way out thre to come out of this stucked ups
Sorry as i cant bear all the conditions this two of my friend shown to me sorry
but thanks to be so kind to me as im new to all this stuffs
waiting and expecting for reply plzzzzzzzzzzzzz help me out here
does anyone knows the conditions by which the mother board become defective or mini usb becomes unfunctional waiting for replyplzzzzzzzzzzzzz
not really much help, but why isnt your phone under waranty?
afaik, the touch HD didnt come (to the UK atleast) till around nov/dec 08 - less than 12months.
also, didn't you think about insuring the HD - not exactly a cheap phone?
-change USB cable - faulty?
-check 'charge via USB' is set on the phone - this wouldnt affect mains charging though
-hard-reset phone
-remove all devices from the phone (sim, battery, SDcard), leave overnight, and try to see if it will charge again in the morning
Charging when Switch off But not charging or syncing whed on
removed all devices from the phone (sim, battery, SDcard), leave overnight, and try to see if it will charge again in the morning
This Trick Worked for Me to Some Extent
Now I can Charge Blackstone By Using usb cable connected to pc but only when the mobile is switched off
When Switched on it doesnt charges
And also It doesnt sync with the pc
Plzzz Help to overcome the next step out
U R the MASTER.....Atleast for me and my blackstone
Waiting for Reply
Your phone may not sync with pc as your usb drivers may need updated. Also check that usb connections has been activated in activesync connection settings
sakiyo6789 said:
removed all devices from the phone (sim, battery, SDcard), leave overnight, and try to see if it will charge again in the morning
This Trick Worked for Me to Some Extent
Now I can Charge Blackstone By Using usb cable connected to pc but only when the mobile is switched off
When Switched on it doesnt charges
And also It doesnt sync with the pc
Plzzz Help to overcome the next step out
U R the MASTER.....Atleast for me and my blackstone
Waiting for Reply
Click to expand...
Click to collapse
You may wish to try this. Go to system settings, power settings and make sure you have unchecked "when device is turned on, do not charge the battery when connected to the PC".
Good luck
thank i will give it a try actually my blackstone battery had been emptied
Than ks ...THANKS A LOT FOR this apreciable replyzzzzzzz
is the problem in my device or on pc
is the problem in my device or on pc
becoz itried to sync my phone with many pc's it wont worked for me
it is not recoznizing my phone even after boot
Can i upgrade it to wm6.5 in this situation if yes then how???????????
plzzzz reply
is the problem in my device or on pc
becoz itried to sync my phone with many pc's it wont worked for me
it is not recoznizing my phone even after boot
Can i upgrade it to wm6.5 in this situation if yes then how???????????
plzzzz reply
sorry my server is hanging out so i repeated it
plzzzzz reply
Upgrade may fix it
i think if we assume it software(driver actually) error the reflashing to original rom or upgrading may fix this(as i have tried hard resetting)
just requiring urs opinion and the way to upgrace in this condition
thank plzzzz reply
When in bootloader does bottom of screen say 'usb' or 'serial' when connected to pc? Have you updated drivers on your pc? Have you tried using a different usb cable? When connected to either usb or charger, does LED at top of phone turn on? Changing rom shouldn't affect this, so I don't see a reason for flashing a new rom just for this.
Same issue
I had the same problem, sent the fone for warranty, which is replaced now..............
Ok but i want to just know can i upgrade or not
sakiyo6789 said:
Ok but i want to just know can i upgrade or not
Click to expand...
Click to collapse
You should still be able to upgrade/flash new rom as long as you follow correct procedure by using either USPL or HSPL
plzzz can any1 redirect me to the lnk from were i can informatn about upgrading in this condition
plzzzz tell me hoe to flash USPL HSPL
PLzzzzzzz
Help a blacston is dieing
plzzz can any1 redirect me to the lnk from were i can informatn about upgrading in this condition
plzzzz tell me hoe to flash USPL HSPL
PLzzzzzzz
Help a blacston is dieing
Hi,I have a Android gingerbread 2.3,haspl v.3,MAGLDR113,it's second time my htc block and dont want to restart from the buton,i have remove the battery and it dosnt want to turn on ,there is no screen,the battery was charget,but the red light don't light when i plug the cabel,in my PC dont recognise usb,nothing and the phone,i try for 1 day to remove a battery,but no result,1st time when it happens it work,but for a week i can't use it,Sorry For my English,Some ideas what can i do before i took it back in the store
sounds like it could be a simple flat battery. when magldr is installed you cannot charge the phone unless android is running, so when it is off it does not charge.
if you can try another battery, or your battery in a winmo hd2, that will tell you if its teh battery.
If you have a spare usb cable (any type, doesnt have to be a hd2 micro usb cable) cut end off, bare red and black, hold red to + and black to - on teh battery for about a minute, which should give it enough power to charge.
Also check very carefully that you dont have a bent battery pin from all teh battery in/out. they bend easily.
i hava a Bat charger and charge the bat all night,and the morning it show me that bat is charget,put it on the phone,but nothing ... cant turn on
Maybe battery is dead. Do you own a volt meter an can check the voltage provided by the battery? It shoud show up about 4 volt.
---------- Post added at 08:12 PM ---------- Previous post was at 08:04 PM ----------
Maybe battery is dead. Do you own a volt meter and can check the voltage provided by the battery? It shoud show up about 4 volt.
i took the bat to my friend with devace to check the battery,and everything is OK,but the phone didn't turn on,Can i reinstal the Android ?and how can i do it
Is there a program that can connect to the phone and erase everything
To wipe the phone install the HD2 toolkit, you can download it here.
It includes every tool needed for maintaining your HD2.
Be sure to install the drivers!
Start the program and press the Task29 button, follow the instructions provided. When it's finished your HD2 will be fully wiped, so you would need to reinstall everything.
Do so by doing a MAGLDR repartition. After that choose MAGLDR update recovery to flash the Clockworkmod recovery.
Then go into the Clockworkmod recovery and flash your rom.
Now your HD2 should be fully wiped
BUT! If your PC doesn't even recognize your HD2, and you can't even get to the bootloader screen by pressing and holding both volume down and the "end call" button. Then it's probably a hardware failure.
Maxp101 said:
To wipe the phone install the HD2 toolkit, you can download it here.
It includes every tool needed for maintaining your HD2.
Be sure to install the drivers!
Start the program and press the Task29 button, follow the instructions provided. When it's finished your HD2 will be fully wiped, so you would need to reinstall everything.
Do so by doing a MAGLDR repartition. After that choose MAGLDR update recovery to flash the Clockworkmod recovery.
Then go into the Clockworkmod recovery and flash your rom.
Now your HD2 should be fully wiped
BUT! If your PC doesn't even recognize your HD2, and you can't even get to the bootloader screen by pressing and holding both volume down and the "end call" button. Then it's probably a hardware failure.
Click to expand...
Click to collapse
Magldr repartition flashes cwm so no need for the update recovery step. That's for, well the clue is in the name,,, updating the cwm version on an already partitioned instal.
Okay, thanks for clarifying that!
Didn't know it worked like that, I only use CLK.
Sent from my HD2 using xda premium
thanks for the information,but Isn't happened like I expect,I still cannot to turn the phone on,and still don't recognize USB,Battery is Full,
Everything i try:
Remove a battery for 1 night
Charge a battery with Charger for battery
Put the charge cable into phone for 1 day
try comb. with keys ( volume up/volume down/Power but.,,volume Down and power but.)but nothing happens.More idaes ??? , or maybe never will wake up this phone ???
more information for the problem
htc hd2 1024 mb with Android gingerbread 2.3,haspl v.3,MAGLDR113
Sd card 2 GB (class 3)
while I play games and watching youyube via wifi connection my charge cable was plugged in the phone,in about a 2,3 hours it freeze,i wait 1,2 minutes and after i try to power off the phone I remove the battery and pul back again and in this moment the phone never turn on.That is maybe everything I know if someone knows or give me a idea what to do,please tell me
I've seen this and similar a few times, when left on charge overnight, and upon waking the phone is totally gone. I've woken up to a fully hard reset phone myself, once, not dead but something weird happened.
Electrical surge, perhaps? Overheated circuits? Who knows.
Somehow the phone start,I have put on my router,and plug in USB all night,in the morning i remove a battery,remove a SDcard put back batery,plug usb and it go,I replace infromation from the card with onother sdcard,flash the phone. 10x for the help,maybe now everything is ok
marto9067 said:
more information for the problem
htc hd2 1024 mb with Android gingerbread 2.3,haspl v.3,MAGLDR113
Sd card 2 GB (class 3)
while I play games and watching youyube via wifi connection my charge cable was plugged in the phone,in about a 2,3 hours it freeze,i wait 1,2 minutes and after i try to power off the phone I remove the battery and pul back again and in this moment the phone never turn on.That is maybe everything I know if someone knows or give me a idea what to do,please tell me
Click to expand...
Click to collapse
I've same problem after similar conditions.
Mine is 512Mb HD2 running Andorid on SD
- while using in extreme conditions: very low network signal, hot ambience temperature, using GPS and downloading data throug 3G
- the screen freeze on image and not respond on touch neiter button
-after 2-3 minutes phone temperature became very hot and screen again on freeze
- removed battery (for power off button not responding)
- insert battery
- no power up, no green LED with AV adaptet, no USB recognized
I'll trying to charge battery but i don't have a table battery chager.
Could you please repeat me what you did, since I didn't get the first part, what did you put on your router (what kind of router please)?
I've tried using my phone with another HD2 phone's battery which is working (and which also started with my own battery?!) but my own phone wouldn't start at all with the other battery...
The battery wasn't fully charged, but did it have to be, if so how long should I charge the battery with the cut USB cable for it to be charged enough please?!
TIA
P.S. I've tried a voltmeter on my battery and it said 4.14V (should it be 4V exactly?) and should I even try the cut USB charge trick again (since I've tried another phone's working battery)?
marto9067 said:
Somehow the phone start,I have put on my router,and plug in USB all night,in the morning i remove a battery,remove a SDcard put back batery,plug usb and it go,I replace infromation from the card with onother sdcard,flash the phone. 10x for the help,maybe now everything is ok
Click to expand...
Click to collapse
dada.81 said:
Could you please repeat me what you did, since I didn't get the first part, what did you put on your router (what kind of router please)?
I've tried using my phone with another HD2 phone's battery which is working (and which also started with my own battery?!) but my own phone wouldn't start at all with the other battery...
The battery wasn't fully charged, but did it have to be, if so how long should I charge the battery with the cut USB cable for it to be charged enough please?!
TIA
P.S. I've tried a voltmeter on my battery and it said 4.14V (should it be 4V exactly?) and should I even try the cut USB charge trick again (since I've tried another phone's working battery)?
Click to expand...
Click to collapse
Ok if I understand you correctly you have tried your battery in a working HD2 and it worked. Then you tried the battery from the working HD2 in your device but your device still did not boot up. If this is correct I do not feel your battery is the problem, but still check the battery pins on your device to make sure none of them are not slightly bent and not making contact properly.
Also if you can provide more info on what you may have done to cause this or what happened when your device reached the state it is currently in. This info can help others and me help you better.
I have a similar problem.
The phone won't start, it gets to the white htc screen sometimes but quits within a fraction of a second.
This has been so since the first Android boot hung (I suspect I have not followed the steps accurately enough...). I have charged, decharged and recharged the battery using the suggested USB-cable technique, but this was of no aid so far, so it's not the battery. Pins and all's fine.
It's someone else's phone, too, so it would be rather unfortunate if I bricked it.
Are there any other common reasons for this behavior? Most tutorials rely on a PC connection, but as it does not recognize such a thing, that's a bit of a problem.
Finally the same problem here.
Battery status was about 70% and running smoothly (WinMO Custom Rom) since installed.Unlocked the Screen and tried to start programs.
The Icons were lightened up but nothing happened.Tried to softrestart...Nothing happened.
Removed and reinserted the Battery.
=> Not turning on.
-another fully charged Battery => nothing
-charging on Charger => nothing not even charging light
-plugged into (running) pc => nothing not even charging light
-5 hours in the fridge => nothing
-charging over night => nothing
Any hints ?
Thx for the goot work around here and greets from Germany !
Sebastian
PS If anyone got one to offer => contact me. Dont like those situations
Bad news!
Seems like your MB is gone...:crying:
Maybe one chance left for a JTAG attempt to a local service shop...
thats what i was afraid of
at least it happend only one hour after i made a backup
thx for the reply !