Database Users

problem magician

I am new of the forum, I have just purchased a nm8 used magiacian (t-mobile MDA) it is I bring a problem.
The preceding owner has begun an updating of the rom that has not gone to good end and the device doesn't now set out anymore and from the following error:
USB V1.00 (if connected USB).
Serial V1.00 (if disconnected).
Bootloader mode ?
What must I do for going on?
I hope in a help
Best regards Luca

help
I pray you helped me, the first post is from beginners, but believe I have followed the standard procedure.
unloaded the rom
unloaded no-id
always tried upgrade more times failure.
HELP !

for the beginning you should use a standard ROM to get familiar with the device.
just go to the t-mobile website, downloads, chose your device type and then look for files named softwareupdates or so.
they will be in zip-format.
there will be an application in there. just go into bootloadermode, connect your device and start the upgrade. it's completely guided and will last about 20min.
although most of the ppl that read/write in this forum didn't install the eROM, I think you can start with all the cusomization stuff. If you have become more familiar with your mdac, you can try other modified ROM's.
just ask if you have more questions
greetz Stefan

i have to say that using standard rom (jam rom downloaded from club imate)
the upgrading applications hangs.....
and leave magician in booting mode, ready to be erased....
i was desperaded, but last experiences with motorola phones and its firmwares advice me to try again
so i had to launch againg that apps and it starts erasing actual rom....
i think there is a bug in few roms.... may be only in its installer

Have tried with the T-mobile rom but doesn't even go with that!

Caslu,
Have you tried a hard-reset?
If so: I guess you've got a decent TMO magician rom downloaded. So get maupgradeut_noid.exe from the ftp. Extract all the files from your TMO shipped-rom & put them in a directory, so you get some .nbf files, enterbl.exe & maupgradeut.exe. Now put the maupgradeut_noid.exe in the same directory. Connect your magician to the usb. It should read usb v1.00, if your magician isn't in bootloader press camera&power&soft-reset at the same time for a few secs. till you get the usb or serial reading.
After connecting it to the usb execute the maupgradeut_noid.exe twice, first execute might give an error 120 second should finish.
If this fails make sure you got a magician & not a charmer.
If it's a magician return it, cause I think it's broken. Hey why buy a device that's in an inconclusive state??
Regards, M

I think really that It broken.
Have picked it because little cost!
non one reply .......

caslu said:
I think really that It broken.
Have picked it because little cost!
non one reply .......
Click to expand...
Click to collapse
Download the latest shipped ROM for the country your magician was first sold in.
Ensure Activesync is in the normal mode (USB check is ON).
Run the executable ROM update program.

Flashing the Radio / modem on ipaq 614 - first ideas

Hi,
Hp just released an update for the 614, only for englisch.
I have a german 614
I dont care about the OS part since I use a cooked 6.1.
But the update also contains a modem / radio update to version 0.88.
Currently out there i think there are 0.77 and 0.81 depending on language.
I believe the radio fw is language independent when it comes to functionality. But the hpruu says wrong language.
With the current universal hpruu tools you can only update the OS which is of no use.
I know you can update the radio by booting with the key combination:
lower left key on the side (record button) and the camera button.
Then turn on ... it shows : SD loader for modem
(similar on how you update the OS)
I also know that the radio update files are in the update.
They are called
amss.mbn
amsshd.mbn
maybe also partition.nbf
But I am not sure about this.
It might work with just copying the file to a non HC SD card and using the key combination.
There might be some file renaming involved.
I someone out there to try that and let us know how it worked ?!
Thanks
sax

hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull

Saxon,
File partition.nbf is for IpaqFileStore update.
Maybe you should try with the following way:
- extract the whole package from HP side
- remove from the obtained directory the OS file (the larger one)
- put your device into SDloader state (voice recorder + mute + power on)
- connect your device into PC via USB
- launch RUU utility
In my opinion there is a big chance it will work.
Such way (using the SDloader) was working for one polish case where the upgrade of firmware failed due to PC crash. The only chance to flash again was to use SDloader + HP tool.
Good luck.

Z!L0G80 said:
hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull
Click to expand...
Click to collapse
I used the qpst already and it worked that way that i could upgrade but phone didnt boot afterwards. so i am very careful with this tool now.
I am just wondering why your sd loader (the OS image) update didnt work. because i had no probs with it so far. also from the hp orig files.
did you try the qpst update ???
if yes did it work if yes can you send a step by step ?
thx a lot

hi , try my patched ROMUpdate.dll mayby it could help , i dont try QPST because i have succesfully update my 614c with hpruu utility --> http://rapidshare.com/files/139300161/ROMUpdate.dll.html

did you also try the cooked wm6.1 os on it already ? does it work with the new fw0.88 ?
thanks !

yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok

Z!L0G80 said:
yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok
Click to expand...
Click to collapse
No success ... either with the romupdate.dll oder with the other tools.
A bit stuck now ... anz other suggestions ?
thanks !

forwarded
29 Jul 2008 release on HP Official Site HP iPAQ 612c WM 6.0en OS 1.01.04 FW 0.88
HOW TO USE:
1. Download the FILE to a directory on your hard drive.
2. Execute the downloaded file and follow the on-screen instructions to unpack the ROM update files to a directory. (NOTE: This directory should not contain any file or folder from any previous ROM upgrade)
3. Establish an ActiveSync connection between the iPAQ device and the host PC using a USB connection.
4. The ROM Update Utility (hpRUU.exe) starts automatically. Follow the on-screen instructions to complete the ROM upgrade.
NOTE: Once the update is complete, the FILE downloaded in Step 1 can be deleted, if desired
Download Link: http://www.mediafire.com/?sharekey=a65dc2a6e56aea29d2db6fb9a8902bda

Thats correct
But thats for english devices.
I have a german one where it doesnt work, and I am looking for a workaround.
Any suggestions ?

Get Hp Sp38905.exe http://h20000.www2.hp.com/bizsuppor...swLang=18&mode=2&taskId=135&swItem=hh-59339-1
Use winrar to unpack it.
You'll find an Eboot.nbf. This Eboot.nbf is language and SKU id independent.
Replace the file header of all .nbf files from hp 1.01.04 update by the header of this Eboot.nbf file.
The header is just the first 3424 bytes of .nbf files.
You do not need to change .mbn files.
Then you can run Hpruu.exe to update. The file names shown during updates are wrong, but results are right.

@kkwy
And what if, like in my case, sp38905 is reporting the same error.
product id: FB136AA#ABB

Just try to find one .nbf file that you can flash.
Then replace header file with the header file of that .nbf file.
The header seems to be useless (solely for checking) so you can replace then at will.

http://rapidshare.com/files/139300161/ROMUpdate.dll.html mayby now working ,try
EDIT> link updated

@ Z!L0G80
Yes, It works.
Thanx

Sucess!!
Now I have os 1.01.04, fw 0.88.
It takes a long time for radio firmware to flash, but, be patient.
Thanx again Z!L0G80

Thanx Z!L0G80's
It works for me to on the Dutch 614.
Strange thing is, that in de system config it stil says Dutch version of the mobile device (but it's UK now).
Very nice again.

ok great .... works ! thanks a lot !
would it also work with the 914 ? anybody tried ?
thx

My PDA already came with 1.01.04, fw 0.88 Rom, however I used the HP rom update utility to see if the rom would update without issues.
The rom update worked fine, however unfortunately something annoying is happening with this rom update. Now every time I try to do a clean boot, the first time the PDA turns on, after marking the screen, it would try to do some HP software update and right after the update I am forced to do a Reset, then I can use the PDA.
Previously I didn't have to do this, when I did a clean boot, the pda worked straight away after marking the screen, and I wouldn't need to reset it.
I think the reason for this maybe because this rom comes with extended rom, is there anyway of taking it back the way it was, or getting rid of the extra applications like the streaming player
This is the Rom I used
Type: BIOS
Version: 1.01.04 (22 Jul 2008)
Operating System(s): Microsoft Windows Mobile 6
File name: sp40097.exe (53 MB)
http://h20000.www2.hp.com/bizsuppor...3048-1&prodTypeId=215348&prodSeriesId=3544358
Am I the only one experiencing this issue, is there another rom that doesn't do this?
Thanks

anyone tried Sd loader modem with success?
what if the Activesycn not work?
I have tried copy the amss** files on SD, then sd loader modem. And wait so long time, 2 hours, and stay with the screen "write amsshd.mbn". I dont think it is working.
Anyone tried ?

[TUT] HP 91x ROM update (fix bricked ipaq and change from any language to english)

Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal

Good job, thanks!
Will try it out later!

is it still compatible even though my device SKU IDs is not compatible with the update?
Last time i tried i almost bricked my device.

In theory, yes
Actually, like I wrote above.
My ipaq 914c is Italian version.
It means that the SKU IDs of the phone is not not compatible with the update. ( I mean the official update!)
But we all know that there is no difference in the hardware between the ipaq 91x.
So any language ROM versions can be used on the another ipaq 91x phone.
=> WWE ROM can be used on any Ipaq 91x phone.
My Ipaq now is in English. But the SKU IDs still show that it's in Italian.
By the way, I forget to thank: Z!L0G80.

i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx

AbsolutBenz said:
i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx
Click to expand...
Click to collapse
Hi,
As it was given like that, I think you should check the usb cable. Sometimes the cable is not working well. I use the original cable, because the last time I use another there was an error when it was flashing. (I'm not sure if the active syn is necessary. In my case, I have the active syn on my laptop. XP enviroment.)
If you want to try the SDBootloader you can find in this forums some instructions about cutting some bytes to obtain the flashdio.nb0
But I really don't recommend that way. Because the last time when I find the way to change the language by flashing the english Rom following those instruction. My phone was bricked. So I tried to find another way.
And this is it.
I think this method is the safest way for newbie. As I wrote above. The first time I bricked my phone. But I did the same procedure again. And it worked.
Just check the procedure again.
Good luck,

For the SDloader update (Which works very very well on my German 914c):
download the file below (I already cut the first 3432 bytes from it), put it on a newly formatted SD-card (not SDHC!) and hold down volumeup+OK button (the one on the right side) while pushing the reset button, hold the mentioned sidebuttons until you see SDloader. Then wait for a few minutes, and the update will finish!
If the updater does not find the file, you have to re-format the SD-card to either FAT or FAT32!
Rename the file to FLASH.DIO when you copy it onto the SD-card!
http://rapidshare.com/files/236053650/FLASH.DIO.html

vragon said:
Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal
Click to expand...
Click to collapse
Hi Everybody,
@vdragon
1- what a great job, guy!
2- in reality, i have already flashed your ROM successfully for my ipaq 914c, which is a native italian version. Since the incompatibilites of different versions were resolved perfectly.
3-Grazie tanto di nuovo

I'm pretty new with this and I've been trying to update my 910 with original ROM but for some reason it gets stuck and the only way to bring it back is with a SDLoader I downloaded from here but that one is very simple and I'd like one with all the programs.
Is there a way to load yours on it through the SD card?

you can follow the instruction to cut the 3432 bytes and flash your phone with SD card.
I see that many people prefer to use the sdloader method than this one.
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.

vragon said:
...
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.
Click to expand...
Click to collapse
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?

congtiger said:
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?
Click to expand...
Click to collapse
sure

congtiger said:
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
Yes it is true!
Using vragon's patched Updater the following is updated:
OS (=ROM)
Bootloader
Pre-Bootloader
Radio&Modem
This update takes about 20minutes, so be patient, do not remove any cables during update!
The flashing of FLASH.DIO with an SD-card "only" updates the OS (=ROM) and is done within less than 10minutes.
Thanks vrago for patching the Romupdate.dll!

You can also see it in the bootsplash screen. Before the update (even after SDloader updates) it always showed FW 1.04.
Now it is 1.09 - and yeah, it works GREAT and quick!
I can recommend it!! (I do not take responsibility though)
Should be a sticky!!

I've been trying this file, and I get an error at 51% of update. Any ideas?

I think it's about your cable. Be sure that you use the original cable with the anti-noise hub.
If you didn't success the first time. Try it again.
Do as you did the first time.
And just be patient. Don't move anything.
The first time I used this method, at the middle of flashing, I kicked my cable and it just stopped. And I did it again carefully.
So that's it

Actually, I think I figured it out. It seems that Vista treats USB partnerships differently than XP, so after a certain amount of time, it "refreshes" the relationship with the USB device. If you are trying to flash your phone, that stops the flash/update.
I just used my XP system, and it worked fine. After a few registry tweaks for ring volume and battery life, it's working fine.
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
I'm positive the SD Loader method isn't as thorough as this method. This method takes 20 minutes or so, and you can see that it's updating the pre-loader, modem/radio, etc. The SD method only updates software.

Problem using HP 614c from original ITA rom
I am a stupd guy
I am a stupd guy
I am a stupd guy
Hy vragon, i have used your method to upgrade my device 614c (and not 914) from an original Italian ROM. All process is ended correctly, all upgrade are finished without errors.
The update utility has made the update of that:
Software - From Version - To Version
Bootloader - 1.00.07 - 1.01.01
Windows Mobile 6.1 Professional - 1.00.07 - 1.01.01
Pre-Bootloader - 1.00.07 - 1.01.01
iPAQ WAN Radio Firmware - 0.81.00 - 1.09.00
But after the upgrade, at the end the display was black(not really black i can see the leds of the entire display are ON but das not appear nothing), and after some minutes abouth 20, i removed the battery and restart the device but nothing has changed. The led over the screen and the sound working.
I have try also to do a hard reset with a flash.dio on an SD card inserted to replace the Rom, but dose not work!
The device after that will work properly, and das not appear to have any problem.
CAN SOMWONE HELP ME !!!

@ilconte81:
just go to hp site.
find a ROM update for 614c.
download it.
using winrar to extract everything in the exe file.
copy the ROMupdate.dll from my file to replace the file in the folder which is extracted from exe file.
run the rom update again.

Tanks for reply vragon,
i have tryed to do what you wrote, but the device will not be right recognized from the OS (will appear USB device not recognized) and the update utlity after a long time in "Plese wait while the device state is verified" give the comunication error Code 402, Cannot comunicate with device.
I use the original cable and try these on different OS like Win XP and Win 7.

MDA II (HTC Himalaya) Disconnection error during flashing.

Greetings developers and enthusiasts!
I was flashing my MDA II (HTC Himalaya) as i did in the past very often. Everything was fine but this time the USB/Disconnection error appeared (Screen shows only Serial/USB & v.1.02). I tried of course the usual steps:
1 - first fully charged battery.
2 - install mobile device center or active sync ( as per your OS )
3 - Enter in to the bootloader mode
4 - connect USB cable with ppc device.
5 - wait for detection of the device
6 - drivers are automatically installed if you are using windows7 it shows
driver installed successfully & device is ready to use.
7 - extract the rom update utility from the posts whichever you like ( remember choose it carefully as per your device )
8 - just double click on upgrade icon in extracted folder and yeah you done.
Click to expand...
Click to collapse
But I’m not able to flash the device with a new rom anymore. I don´t know what went wrong and why I’m not able to reflash the device.
Windows 7/64 identifies the USB-Device correctly. But the updater (ROM) says there is a connection problem/101.
May be I´m missing something.
Thanx in advance!
-Agesilaos
UPDATE:
I tried another PC with Windows 7/32
Same Problem again with error 101 and device still in bootloader mode.

Agesilaos said:
Greetings developers and enthusiasts!
I was flashing my MDA II (HTC Himalaya) as i did in the past very often. Everything was fine but this time the USB/Disconnection error appeared (Screen shows only Serial/USB & v.1.02). I tried of course the usual steps:
But I’m not able to flash the device with a new rom anymore. I don´t know what went wrong and why I’m not able to reflash the device.
Windows 7/64 identifies the USB-Device correctly. But the updater (ROM) says there is a connection problem/101.
May be I´m missing something.
Thanx in advance!
-Agesilaos
UPDATE:
I tried another PC with Windows 7/32
Same Problem again with error 101 and device still in bootloader mode.
Click to expand...
Click to collapse
You must Update (downgrade) your driver for flashing in Win7!!!!
See in my signatur english thread and look in the HowTo section i know it is for Blue Angel but it works

d-two said:
You must Update (downgrade) your driver for flashing in Win7!!!!
See in my signatur english thread and look in the HowTo section i know it is for Blue Angel but it works
Click to expand...
Click to collapse
Greetings d-two!
Herzlichen Dank für Deine Hilfe!
Thanks a lot for your help!
I remember i did an upload of the usb driver back in 2009 during the windows7-BETA but i forgot that step!
It works very fine now due to your nice manual!
This threat should be sticky don´t you think?
Best regards from Athens,
-Agesilaos

Agesilaos said:
Greetings d-two!
Herzlichen Dank für Deine Hilfe!
Thanks a lot for your help!
I remember i did an upload of the usb driver back in 2009 during the windows7-BETA but i forgot that step!
It works very fine now due to your nice manual!
This threat should be sticky don´t you think?
Best regards from Athens,
-Agesilaos
Click to expand...
Click to collapse
Thanks, I know that this is important but no one wants to make as a sticky!

[ROM] For developer only

Hi
i'm working on hd2 rom and after dump a schubert test rom.
i have notice this one contain a lots of usefull tools.
RUU_Schubert_hTC_Asia_SEA_WWE_1.57.728.02_Radio_5.52.09.16_22.33a.50.10_Signed_SCHUBERT_TEST
This rom contain kitl tools allowing connection to remote tools framework
a part of Windows Embedded Compact 7 developper tool.(with registry editor and more)
sirep server allowing connection to.
also a tool to test all device sensor.
and a tool to see touchscreen raw data and more...
Maybe use this rom can help dev to find more.
you can also flash this rom with goldcard if your device is not unbranded.
i don't have HD7 Device so i can't help you with this.

Is the USB-Switch mode also included, because i'm stuck in Diagnostic Mode and it would be great...
Can i flash it with my European unbranded device?
Is there a Version-Controll?
because i have currently the 1.60 ROM installed...
thx.
Tried it but said not for my device... (after 1% flashed)

Oberoth said:
Is the USB-Switch mode also included, because i'm stuck in Diagnostic Mode and it would be great...
Can i flash it with my European unbranded device?
Is there a Version-Controll?
because i have currently the 1.60 ROM installed...
thx.
Tried it but said not for my device... (after 1% flashed)
Click to expand...
Click to collapse
i think you need to use goldcard to flash it.

damn...
i don't have goldcard, nor an y-cable to make one :'-(
chance for SSPL in near future?

downloading now , hope to get my goldcard working , last time it didn't work

i must wait till next week to build a Y-Cable
could you tell me if it works and if there is the USB-Switch-App in the ROM?
thanks

xboxmod said:
i think you need to use goldcard to flash it.
Click to expand...
Click to collapse
Hi,
You can not do it with GoldCard. First of all, you must have xxx.nbh file to use a GoldCard. ROM from first post does't have.
Regards

it does work...
i did it...
you need to extract the exe using WinRAR...
then there is your .nbh file...

Oberoth said:
it does work...
i did it...
you need to extract the exe using WinRAR...
then there is your .nbh file...
Click to expand...
Click to collapse
is that means.. now your phone has turn into ZUNE mode
back? Series? How? Do you mind to tech me on this?
I've download everything needed.. only need to build my own Y-Cable.
Appreciate your share.
Thanks~

No...
the needed app isn't in the main menu...
xboxmod (by the way... great thanks from me) and i are trying to open theese files because they are indeed in the rom....

Oberoth said:
it does work...
i did it...
you need to extract the exe using WinRAR...
then there is your .nbh file...
Click to expand...
Click to collapse
Oh, really. Check once again !!

xboxmod said:
Hi
i'm working on hd2 rom and after dump a schubert test rom.
i have notice this one contain a lots of usefull tools.
RUU_Schubert_hTC_Asia_SEA_WWE_1.57.728.02_Radio_5.52.09.16_22.33a.50.10_Signed_SCHUBERT_TEST
This rom contain kitl tools allowing connection to remote tools framework
a part of Windows Embedded Compact 7 developper tool.(with registry editor and more)
sirep server allowing connection to.
also a tool to test all device sensor.
and a tool to see touchscreen raw data and more...
Maybe use this rom can help dev to find more.
you can also flash this rom with goldcard if your device is not unbranded.
i don't have HD7 Device so i can't help you with this.
Click to expand...
Click to collapse
At last... I've successful flash my devices using this ROM and Goldcard.
But to switch it back from DIAG to ZUNE, as you've said.. the USBtool.exe
has to be execute manually. I just wait maybe someone could found it how.
It's was really hard to find the single micro memorycard reader in my place.
I already try to use the multi/all in 1 mmc reader.. it wont work to
flash using goldcard technique because it seems like the phone keep searching
which one it should read from. so i manage to create my goldcard using flash
thumbdrive 4GB. and it works perfect with me. So now.. I have no worried to
flash any rom. except it was not develope for WP7. lol~

AzmanIshak said:
But to switch it back from DIAG to ZUNE, as you've said.. the USBtool.exe
has to be execute manually. I just wait maybe someone could found it how.
Click to expand...
Click to collapse
I'm talking to some developers to get enough information to get back into Zune Mode...
will make a thread when its done...

Oberoth said:
I'm talking to some developers to get enough information to get back into Zune Mode...
will make a thread when its done...
Click to expand...
Click to collapse
Wohooo.... serious nice. cant wait...
Please let me know when you've done.
thanks!

were you able to resolve this?
if it does not have the needed mode switcher app, can someone kindly create a custom rom with the needed app(usbmodeswitcher.xap)
Thanks

the problem is that we cannot flash that rom until we have HSPL or SSPL...
no chance to resolve the problem yet :-/

DF Router
can anyone build rom for HD7 with preinstaled "DF Router" app?
I changed usb mode to modem and I uninstalled this app, now i can connect to zune and install it again
am now in "modem mode" and i need back to "Zune mode"
more info about DF Router problem
answers.microsoft.com/en-us/winphone/forum/wp7-sync/any-solution-for-damaged-windows-phone-via-df/2109119d-0259-448a-9162-73ea1a7eed3a?tm=1308688395627

Hi.
The only way => back to repaire.
or try to flash it ....

now i have succesfull flashed this rom via goldcard.
but i still stuck in diag-mode, so i cant still connect via zune, is there already a solution for this problem??? =(
greetz nOoG

The good news first: We now have RSPL/HSPL (thanks to Cotulla and DFT)
The bad news: Nobody made a ROM which contains the USBSwitch-App :/
I hope that will change