i'm so sorry but i am going to get crazy if i can't find a solution.
What ever i tried, i could not flash my at&t xperia x10a.
it has stock rom 2.1
i tried flashtool 0.6.9.1
here is the log........................................................................
18/054/2012 00:54:51 - INFO - Connected device : X10
18/054/2012 00:54:51 - INFO - Installed version of busybox : BusyBox v1.19.0 (2011-08-14 23:46:58 CDT) multi-call binary.
18/054/2012 00:54:51 - INFO - Android version : 2.1-update1 / kernel version : 2.6.29
18/054/2012 00:54:52 - INFO - Root Access Allowed
18/055/2012 00:55:18 - INFO - Selected X10a_v2.1.update-1_2.1.A.0.435_Generic.ftf
18/055/2012 00:55:18 - INFO - Preparing files for flashing
18/055/2012 00:55:18 - INFO - Please connect your device into flashmode.
18/055/2012 00:55:20 - INFO - Device disconnected
18/055/2012 00:55:40 - INFO - Device connected in flash mode
18/055/2012 00:55:40 - INFO - Opening device for R/W
18/055/2012 00:55:40 - INFO - Reading device information
18/055/2012 00:55:40 - INFO - Phone ready for flashmode operations.
18/055/2012 00:55:40 - INFO - Start Flashing
18/055/2012 00:55:40 - INFO - Flashing loader
18/055/2012 00:55:44 - INFO - Loader : S1_Loader_Root_f851 - Version : R4A024 / Bootloader status : ROOTED
18/055/2012 00:55:44 - INFO - Ending flash session
18/055/2012 00:55:44 - INFO - Flashing finished.
18/055/2012 00:55:44 - INFO - Please wait. Phone will reboot
18/055/2012 00:55:44 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
18/055/2012 00:55:44 - INFO - Device connected in flash mode
18/055/2012 00:55:45 - INFO - Device disconnected
...........................................................................................
at&t prevented phone from unknown sources therefore, i can't flash it.
any suggestions ?
Shouldn't matter if you have unknown sources checked. Did you enable usb debugging?
Sent from a galaxy far, far away...
you can flash your phone no matter what just make sure to connect properly(in flash mode..pull out battery. Put back in.hold back button while powered of and plug in USB while doing so
Edit: what are you trying to do exactly?
Sent from my X10i using XDA
18/055/2012 00:55:44 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
Agree check debugging
settings/applications/development
From XDA on my XPERIA X10-S, powered by DooMKerneL
usb debugging is on...
i noticed that flash tool does not show firmware content ??? can it be the reason ?
1) i run flashtool.
2) connect phone to pc by usb
3) i click to flash button and proper rom
4) flashtool want me to plug off the usb and turn the phone off.
5) i do as it says. turning off, pulling battery out. putting it back. holding the back button while connetcing usb. green light appears.
6) as a result it reboot the phone everytime i try to flash.
ohhh at last.
guys... believe in searching . in xda forums, i found some guys with same problem. i mentioned the solution below.
i finally noticed that ftool does not see firmware content. The reason is surprising. I am in Turkey and location and language in windows 7 are stated as Turkish and Turkey. By changing them to USA and English, flashtool started to see content and now i did it.
thank you everybody for your attention.
hello, well, as topic says, i have problem rooting my phone, more specifically it's build number is JDQ39.G350XXU0ANI1 ..... their list of supported models says my phone IS supported, but when i try to root it, well, here's log :
---= SRS One-Click-Root v4.7 =---
18:37:04 - Starting ADB Server..
18:37:09 - Manufacturer: samsung
18:37:10 - Model: SM-G350
18:37:10 - Android Version: 4.2.2
18:37:10 - Build ID: JDQ39.G350XXU0ANI1
18:37:10 - Board ID: hawaii
18:37:10 - Chipset Platform: hawaii
18:37:10 - Getting OffSets.. : 0x8003 0x8005 (False)
18:37:11 - Query Server for Best Method.. Found Rootkit: 4
----= Start Rooting Process.. Please Wait =----
18:37:13 [+] Testing exploit: root4 (please wait..)
18:37:16 [+] Device Reboot #1 (Wait till it's started)
18:39:27 [+] Device Reboot #2 (Wait till it's started)
18:41:37 [+] Executing root4 exploit Failed.
18:41:37 [+] Testing exploit: root4b (please wait..)
18:41:43 [+] Device Reboot #1 (Wait till it's started)
18:43:10 [+] Device Reboot #2 (Wait till it's started)
18:45:02 [+] Testing exploit: root5 (please wait..)
18:45:04 [+] Unlock your device screen, it should bring up restore mode.
18:45:29 [+] Press RESTORE button on device NOW! then wait...
18:46:05 [+] Device Reboot #1 (Wait till it's started)
18:49:23 [+] Executing root5 exploit Failed.
18:49:23 Auto Root Failed on this device.
18:49:23 Rebooting Device and try again...
......could you guys help me ? im gettin desperate here
or perhaps you could give me tip on some other software or app ?
Hi! Have you managed to root it? Because I have the same firmware and wasn't able to root it either, so I was wondering if you had found out a solution.
Unfortunately SRS Root site/devs list arbitrary devices that actually don't work . Ran into it first hand.
Sent from my HUAWEI Y536A1 using XDA Free mobile app
hello, I hope that I write in the right place and I will not be scolded.
I have a big problem. I'll start from the beginning.
I did root my tablet and everything was OK.
Before root I made data backup in TWRP recovery.
I used a moment then something began to manifest errors.
That's why I thought that restore backup.
Everything I've done with the use 'IntelAndroid-FBRL-07-24-2015'.
When I restored a backup system will not boot.
He hang on the logo LENOVO and after a while tablet restarted.
I thought that restore everything as it was at the factory.
I downloaded "YT2-830L_USR_S000067_1410301707_WW21_ROW" and I launched the program "PhoneFlashTool_4.4.4.1_external_win32".
At the beginning everything was ok.
Then there was about 50/60 percent and jumped an error.. Unfortunately, I do not remember what.
The device was restarts and and appeared logo LENOVO + Subtitles "Boot Failed. EFI HARD DRIVE" "Boot Succeed - enter startup"
and then pops up
"VALLEYVIEW C0 PLATFORM
INTEL (R) ATOM ....
...
...
CONTINUE
SELECT LANGUAGE
> BOOT MANAGER
> DEVICE MANAGER
> BOOT MAINTANCE MANAGER
"
I tried again to upload the original tablet software..
and so it looked like:
"12/25/15 23:18:44.251 INFO : Phone Flash Tool V 4.4.4-1 Win32 External (build on Mon Apr 28 09:56:35 UTC 2014)
12/25/15 23:18:44.251 INFO : Using xFSTK version: 1.5.3
12/25/15 23:18:44.361 INFO : Using Android Debug Bridge version 1.0.31
12/25/15 23:18:44.361 INFO : OS version detected: Windows 8 (x64)
12/25/15 23:18:44.580 INFO : Adb and fastboot binaries OK
12/25/15 23:18:44.580 INFO : Phone Flash Tool initialized successfully
12/25/15 23:18:44.595 INFO : Loading Flash file ...
12/25/15 23:18:44.595 INFO : Ready to flash!
12/25/15 23:19:28.233 INFO : Loading Flash file (C:/Users/X/Desktop/FLASH_LENOVO/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2_8_row_lte-blankphone-user-YT2-830L_USR_S000067_1410301707_WW21_ROW/flash.xml)
12/25/15 23:19:28.233 INFO : GP_Flag is set to 0x80000045
12/25/15 23:19:28.249 INFO : Ready to flash!
12/25/15 23:19:30.689 INFO : Port 1/1: Flashing OS
12/25/15 23:19:30.689 INFO : Port 1/1: fastboot -s BaytrailF0B3F8A3 -S 500M flash osloader "C:/Users/X/Desktop/FLASH_LENOVO/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2_8_row_lte-blankphone-user-YT2-830L_USR_S000067_1410301707_WW21_ROW/efilinux.efi"
12/25/15 23:19:32.830 INFO : Port 1/1: fastboot -s BaytrailF0B3F8A3 -S 500M boot "C:/Users/X/Desktop/FLASH_LENOVO/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2-830L_USR_S000067_1410301707_WW21_ROW/YT2_8_row_lte-blankphone-user-YT2-830L_USR_S000067_1410301707_WW21_ROW/droidboot.img"
12/25/15 23:19:35.537 INFO : Port 1/1: sleep 25000 ms"
AND THE TABLET RESTART AND SEE AGAIN WINDOW
"VALLEYVIEW C0 PLATFORM
INTEL (R) ATOM ....
...
...
CONTINUE
SELECT LANGUAGE
> BOOT MANAGER
> DEVICE MANAGER
> BOOT MAINTANCE MANAGER
"
(in THE PROGRAMME IS 23 %)
So I run again tablet and TO FASTBOOT AND IN THE PROGRAM POPS ERROR
"12/25/15 23:20:00.538 INFO : Port 1/1: fastboot -s BaytrailF0B3F8A3 -S 500M oem wipe ESP
12/25/15 23:23:32.881 WARNING: Port 1/1: Failed to execute ""C:/Program Files (x86)/Intel/Phone Flash Tool/fastboot.exe" -s BaytrailF0B3F8A3 -S 500M oem wipe ESP":
< waiting for device >
...
FAILED (remote: unknown command)
finished. total time: 0.003s
12/25/15 23:23:34.884 WARNING: Port 1/1: Retry to execute fastboot -s BaytrailF0B3F8A3 -S 500M oem wipe ESP
12/25/15 23:23:34.978 WARNING: Port 1/1: Failed to execute ""C:/Program Files (x86)/Intel/Phone Flash Tool/fastboot.exe" -s BaytrailF0B3F8A3 -S 500M oem wipe ESP":
...
FAILED (remote: unknown command)
finished. total time: -0.000s
12/25/15 23:23:36.994 WARNING: Port 1/1: Failed to execute non mandatory command fastboot -s BaytrailF0B3F8A3 -S 500M oem wipe ESP, ignoring error
12/25/15 23:23:36.994 INFO : Port 1/1: fastboot -s BaytrailF0B3F8A3 -S 500M oem start_partitioning
12/25/15 23:23:37.088 WARNING: Port 1/1: Failed to execute ""C:/Program Files (x86)/Intel/Phone Flash Tool/fastboot.exe" -s BaytrailF0B3F8A3 -S 500M oem start_partitioning":
...
FAILED (remote: unknown command)
finished. total time: 0.000s
12/25/15 23:23:39.098 WARNING: Port 1/1: Retry to execute fastboot -s BaytrailF0B3F8A3 -S 500M oem start_partitioning
12/25/15 23:23:39.207 WARNING: Port 1/1: Failed to execute ""C:/Program Files (x86)/Intel/Phone Flash Tool/fastboot.exe" -s BaytrailF0B3F8A3 -S 500M oem start_partitioning":
...
FAILED (remote: unknown command)
finished. total time: -0.000s
12/25/15 23:23:41.223 ERROR : Port 1/1: Flash failure"
ON THE TABLET IS "FASTBOOT STARTING ..."
when I choose continue on this screen
VALLEYVIEW C0 PLATFORM
INTEL (R) ATOM ....
...
...
CONTINUE
SELECT LANGUAGE
> BOOT MANAGER
> DEVICE MANAGER
> BOOT MAINTANCE MANAGER"
i see this window WHERE WRITE:
"BOOT FAILED. EFI HARD DISK"
"BOOT SUCCEED - ENTER SETUP"
if anyone knows how to solve , how to restore the tablet to work please help !!!
SORRY I did not give photos, but I'm new and I could not INSERT...
progdvb said:
hello, I hope that I write in the right place and I will not be scolded.
Click to expand...
Click to collapse
you were on Lollipop when you bricked and now you are trying to flash a kitkat rom, this will not work as the kiktak rom files (IA32) pushed by the Phone Flash tool are not recognized by the Lollipop bios (x64).
since there is no publicly available (leaked) lollipop stock rom for the 830L model you will have to:
1. downgrade first your bios to the kitkat version using the steps in here, do the steps in 'how to use'
2. now flash your kitkat stock rom, remember to set your country code when finished flashing, on your first boot, or you will fail in the future when attempting to update using an OTA
3. optional, update to lollipop using the OTA when prompted by your (now) running kitkat android
ionioni said:
you were on Lollipop when you bricked and now you are trying to flash a kitkat rom, this will not work as the kiktak rom files (IA32) pushed by the Phone Flash tool are not recognized by the Lollipop bios (x64).
since there is no publicly available (leaked) lollipop stock rom for the 830L model you will have to:
1. downgrade first your bios to the kitkat version using the steps in here, do the steps in 'how to use'
2. now flash your kitkat stock rom, remember to set your country code when finished flashing, on your first boot, or you will fail in the future when attempting to update using an OTA
3. optional, update to lollipop using the OTA when prompted by your (now) running kitkat android
Click to expand...
Click to collapse
I tried this way now and the program stay in position "waiting for access to root shell".
It takes a fewww minutes...
in the video demo it quickly went...
what now?
ON THE TABLET IS WINDOW AND WRITE "CMD 'STOP_PARTITIONING' COMPLETE.
progdvb said:
I tried this way now and the program stay in position "waiting for access to root shell".
It takes a fewww minutes...
in the video demo it quickly went...
what now?
Click to expand...
Click to collapse
if it went to that point the bios restoring has not yet started (yet it confirms you are on lollipop bios) so you can close the tool exe window safely
this can mean one of these things:
1. (most likely) your drivers need to be reinstalled, download from here and install both files in the zip (accepting whatever it prompts you and using defaults) and reboot at the end your pc, then try again the downgrading the bios, if it still hangs on that 'waiting for root shell' try when you get ther and some seconds have passed to unplug and replug the usb to force a redetection of the new usb mode (windows does it automatically, never met a case where it didn't yet you can try it)
2. (unlikely) you are using windows in a virtual environment such as virtualbox or vmware (are you?) and it did not detected the usb changing mode, if that is the case (only if you are using windows in virtualbox, i doubt) unplug and replug the usb when it says 'waiting for root shell'
3. (almost impossible) your usb controller is bricked
I did reinstalling drivers.
Went two steps further.
[pc] transfering control to yogatab device for bios restoring.
AND Unfortunately, he jumped error:
adb server is out of date. killing...
abd server didnt ACK
*failed to start daemon *
error:
progdvb said:
I did reinstalling drivers.
Went two steps further.
[pc] transfering control to yogatab device for bios restoring.
AND Unfortunately, he jumped error:
adb server is out of date. killing...
abd server didnt ACK
*failed to start daemon *
error:
Click to expand...
Click to collapse
but the tablet rebooted?
NEVER POWER OFF YOUR TAB AFTER IT SAYS "TRANSFERING CONTROL" ALWAYS WAIT 4-5 MINUTES BEFORE TRYING TO REBOOT THE TAB IF YOU GOT DISCONNECTED SOMEHOW!
that means the bios restore could have been started and you must wait 4-5 minutes and ONLY if it doesn't reboot by itself in 4-5 minutes then you can try to reboot
you must take care with this as if the bios restore is started (and you were disconnected meaning no more messages from your tab) if you power off by force your tab you can hard-brick and nothing can be done to save it (you must send it to a service).
READ THE INSTRUCTIONS IN THE DOWNGRADING POST!
do this:
UNINSTALL everything: adb/fastboot, drivers installed in the past, Intel Phone Flash Tool, everything you installed related to the tab
REBOOT
INSTALL the two files provided in the link
REBOOT
TRY AGAIN to downgrade
also, you should use when flashing your kitkat a more recent stock rom (the one you used is old) download extract and use this (after you managed to downgrade the bios of course)
ionioni said:
but the tablet rebooted?
NEVER POWER OFF YOUR TAB AFTER IT SAYS "TRANSFERING CONTROL"
that means the bios restore could have been started and you must wait 4-5 minutes and ONLY if it doesn't reboot by itself in 4-5 minutes then you can try to reboot
you must take care with this as if the bios restore is started (and you were disconnected meaning no more messages from your tab) if you power off by force your tab you can hard-brick and nothing can be done to save it (you must send it to a service).
READ THE INSTRUCTIONS IN THE DOWNGRADING POST!
Click to expand...
Click to collapse
Yes, I wait 5-6minute and power off tablets.
he did not restarted itself.
Now I try uninstall, and install program and all drivers.
--------------------------------------------------------------------
OK,
I uninstalled and install anew driver, I open program and now is hang on
[pc] transfering control to yogatab device for bios restoring.
========================================
adb server is out of date. killing...
so this situation has been going 5min
progdvb said:
Yes, I wait 5-6minute and power off tablets.
he did not restarted itself.
Now I try uninstall, and install program and all drivers.
Click to expand...
Click to collapse
ok, read above i edited some stuff... the bios restoring is a safe process (as long as you don't do stupid things) but you have issues on your pc, solve them first
after you downgrade the bios use the stock rom i linked in the prev post for your kitkat stock rom flashing, the one you used is old (should work but you will wait forever after for the ota's)
---------- Post added at 11:24 ---------- Previous post was at 11:13 ----------
progdvb said:
Yes, I wait 5-6minute and power off tablets.
he did not restarted itself.
Now I try uninstall, and install program and all drivers.
--------------------------------------------------------------------
OK,
I uninstalled and install anew driver, I open program and now is hang on
[pc] transfering control to yogatab device for bios restoring.
========================================
adb server is out of date. killing...
so this situation has been going 5min
Click to expand...
Click to collapse
reboot and go to the intel phone flash tool folder C:\Program Files (x86)\Intel\Phone Flash Tool Lite and delete the adb.exe file inside and try again
you have some adb.exe (old) file that starts automatically and that makes things go wrong (have you uninstalled your stuff?) also make sure you run the exe as Administrator
ionioni said:
ok, read above i edited some stuff... the bios restoring is a safe process (as long as you don't do stupid things) but you have issues on your pc, solve them first
after you downgrade the bios use the stock rom i linked in the prev post for your kitkat stock rom flashing, the one you used is old (should work but you will wait forever after for the ota's)
---------- Post added at 11:24 ---------- Previous post was at 11:13 ----------
reboot and go to the intel phone flash tool folder C:\Program Files (x86)\Intel\Phone Flash Tool Lite and delete the adb.exe file inside and try again
you have some adb.exe (old) file that starts automatically and that makes things go wrong (have you uninstalled your stuff?) also make sure you run the exe as Administrator
Click to expand...
Click to collapse
OK, I used other computer. Its work.
Program passed with no errors.
Now I have to use 'Phone Flash Tool Lite',
upload a rom from the link you gave me and everything should be ok ?
progdvb said:
OK, I used other computer. Its work.
Program passed with no errors.
Now I have to use 'Phone Flash Tool Lite',
upload a rom from the link you gave me and everything should be ok ?
Click to expand...
Click to collapse
yes, use the rom i linked extract and flash from dnx mode ("fastboot starting" message on screen pwr+volup+voldown to start in dnx)
ionioni said:
yes, use the rom i linked extract and flash from dnx mode ("fastboot starting" message on screen pwr+volup+voldown to start in dnx)
Click to expand...
Click to collapse
when I had to choose a country that updates work later?
and how?
during the first run I introduced tablet in dialer ####6020# ?
next choose my country and tablet restart and next #### 59930# to check the chosen country?
progdvb said:
when I had to choose a country that updates work later?
and how?
during the first run I introduced tablet in dialer ####6020# ?
next choose my country and tablet restart and next #### 59930# to check the chosen country?
Click to expand...
Click to collapse
you open Contacts app and input there
ionioni said:
you open Contacts app and input there
Click to expand...
Click to collapse
OK. For now uploads a rom .
By the way, I ask yet .
Is it possible for me I've loaded rom that will allow me to call from the tablet?
I read this article but I could not quite understand everything
http://forum.xda-developers.com/thi...guide-make-lenovo-tablet-yoga-2-830l-t2950933
Do you know where can I download Lenovo Tablet Yoga 2 830LC to fit what you gave me?
the manual says to replace the file called "esp.img"..
progdvb said:
OK. For now uploads a rom .
By the way, I ask yet .
Is it possible for me I've loaded rom that will allow me to call from the tablet?
I read this article but I could not quite understand everything
http://forum.xda-developers.com/thi...guide-make-lenovo-tablet-yoga-2-830l-t2950933
Do you know where can I download Lenovo Tablet Yoga 2 830LC to fit what you gave me?
the manual says to replace the file called "esp.img"..
Click to expand...
Click to collapse
this is the 830LC stock kitkat rom flash it and see...
ionioni said:
this is the 830LC stock kitkat rom flash it and see...
Click to expand...
Click to collapse
THE TABLET IS WORKING !!!!!!
YOY are GREAT !!!!!!!!!!!!!!!!!!!!!!!!!!!!
Tell me again, which country should I choose for Polish ?
the same Chinese stamps and some strange abbreviations are...
progdvb said:
THE TABLET IS WORKING !!!!!!
YOY are GREAT !!!!!!!!!!!!!!!!!!!!!!!!!!!!
Tell me again, which country should I choose for Polish ?
the same Chinese stamps and some strange abbreviations are...
Click to expand...
Click to collapse
the abbreviations are the standard iso country alpha 2 letter code https://en.wikipedia.org/wiki/ISO_3166-1
if you don't have PL then chose a neighbour one, not sot important (this is not the language in which your Android interface will be shown that you can set with the Language on your Settings)
ionioni said:
the abbreviations are the standard iso country alpha 2 letter code https://en.wikipedia.org/wiki/ISO_3166-1
if you don't have PL then chose a neighbour one, not sot important (this is not the language in which your Android interface will be shown that you can set with the Language on your Settings)
Click to expand...
Click to collapse
ok . I found a country close to the Polish (germany)
if I set this country I will be able to use the system updates ?
I will be able to upgrade to 5.0 android?
progdvb said:
ok . I found a country close to the Polish (germany)
if I set this country I will be able to use the system updates ?
I will be able to upgrade to 5.0 android?
Click to expand...
Click to collapse
yes, as i told you is not so important, whatever you will chose you will be able to complete updates (to lollipop included)
ionioni said:
yes, use the rom i linked extract and flash from dnx mode ("fastboot starting" message on screen pwr+volup+voldown to start in dnx)
Click to expand...
Click to collapse
if I install rom which allows ringing ,
whether later I will be able to update it eg. to 5.0
and still I could call from tablet ?
progdvb said:
if I install rom which allows ringing ,
whether later I will be able to update it eg. to 5.0
and still I could call from tablet ?
Click to expand...
Click to collapse
you can update, if it works in kitkat will work in lollipop
Hello guys!
A person of my family has bought a Lenovo Yoga Tablet 2 1050F from China. The problem is there are only chinese and english language to select. The firmware are chinese, and i have downloaded a firmware with multilanguage from NEEDROM.
I not know how can i flash this firmware, I have instaled Phone Flash Tool 4.4.4., but when I try to start flash and the device it reboots in Flashboot mode, my computer not detect the device, and the operation finish without any profit result for me.
Device start normal boot when I unplug the usb cable.
Thank for all.
ABOUT DEVICE:
- Model number: YOGA Tablet 2-150F
- Android 4.4.2
- Software version: YOGA Tablet 2-1050f_150428
- Build number: YOGATablet2-1050F_S000175_150428
Serial Num: BaytrailD482531E
DROIDBOOT VERSION 2.0
PRODUCT: YT2_10_PR
Please, help me.
Best to install adb and fastboot.
Do adb devices from command prompt and see if they it displays your device
You need to go on to device manager when you phone is in fastboot mode, connected to your PC. There WILL be a ! Next to your device.
Click update driver and then select from my PC Not windows update. Select the the driver installed when in normal mode and select adb driver
Sent from my SM-G901F using Tapatalk
Hi Rob
VictorVL90
In the settings when you go to Language and input,can you change to the language you want there.
pug1 said:
Best to install adb and fastboot.
Do adb devices from command prompt and see if they it displays your device
You need to go on to device manager when you phone is in fastboot mode, connected to your PC. There WILL be a ! Next to your device.
Click update driver and then select from my PC Not windows update. Select the the driver installed when in normal mode and select adb driver
Sent from my SM-G901F using Tapatalk
Click to expand...
Click to collapse
work, but... stop at 26%
02/24/16 20:09:15.881 INFO : Phone Flash Tool V 4.4.4-1 Win32 External (build on Mon Apr 28 09:56:35 UTC 2014)
02/24/16 20:09:15.881 INFO : Using xFSTK version: 1.5.3
02/24/16 20:09:15.959 INFO : Using Android Debug Bridge version 1.0.31
02/24/16 20:09:15.959 INFO : OS version detected: Windows 8 (x64)
02/24/16 20:09:16.147 INFO : Adb and fastboot binaries OK
02/24/16 20:09:16.147 INFO : Phone Flash Tool initialized successfully
02/24/16 20:09:16.163 INFO : Loading Flash file ...
02/24/16 20:09:16.163 INFO : Ready to flash!
02/24/16 20:09:40.479 INFO : Loading Flash file (C:/Users/Víctor Valle/Downloads/YOGA-Tablet-2-1050F/YOGA-Tablet-2-1050F/target_bin/flash.xml)
02/24/16 20:09:40.479 INFO : GP_Flag is set to 0x80000045
02/24/16 20:09:40.479 INFO : Ready to flash!
02/24/16 20:09:46.464 INFO : Port 0/3: Flashing OS
02/24/16 20:09:46.464 INFO : Port 0/3: fastboot -s INTD482531E flash osloader "C:/Users/Víctor Valle/Downloads/YOGA-Tablet-2-1050F/YOGA-Tablet-2-1050F/target_bin/efilinux.efi"
02/24/16 20:09:48.604 INFO : Port 0/3: fastboot -s INTD482531E boot "C:/Users/Víctor Valle/Downloads/YOGA-Tablet-2-1050F/YOGA-Tablet-2-1050F/target_bin/droidboot.img"
02/24/16 20:09:51.381 INFO : Port 0/3: sleep 25000 ms
02/24/16 20:10:16.384 INFO : Port 0/3: fastboot -s INTD482531E oem wipe ESP
02/24/16 20:13:56.682 WARNING: Port 0/3: Process TIMEOUT Failed to execute ""C:/Program Files (x86)/Intel/Phone Flash Tool/fastboot.exe" -s INTD482531E oem wipe ESP"
02/24/16 20:13:58.690 WARNING: Port 0/3: Retry to execute fastboot -s INTD482531E oem wipe ESP
Click to expand...
Click to collapse
VictorVL90 said:
work, but... stop at 26%
Click to expand...
Click to collapse
Have you installed http://forum.xda-developers.com/showthread.php?p=48915118#post48915118.
I use this method without fail on win10 pro
Sent from my SM-G901F using Tapatalk
Try using this Rom , tinyurl.com/hn9m7rc
also copy the easyimage zip file in the download to a memory card in the tablet to enable you to set the country code.
It is clean,it's the one I used.
pug1 said:
Have you installed http://forum.xda-developers.com/showthread.php?p=48915118#post48915118.
I use this method without fail on win10 pro
Sent from my SM-G901F using Tapatalk
Click to expand...
Click to collapse
GREAT! Tablet work full 100%
Thanks!
One more question...
Occasionally, the System try to update a patch, but the installation always failure. What can i do for prevent this automatically update?
VictorVL90 said:
One more question...
Occasionally, the System try to update a patch, but the installation always failure. What can i do for prevent this automatically update?
Click to expand...
Click to collapse
Usually you are asked if you want to install the update,just say no.
VictorVL90 said:
One more question...
Occasionally, the System try to update a patch, but the installation always failure. What can i do for prevent this automatically update?
Click to expand...
Click to collapse
Are you on stock unrooted firmware? If so you could try going into stock recovery and factory reset. Then try to let the update install. I would always go with an update.
corasman said:
Usually you are asked if you want to install the update,just say no.
Click to expand...
Click to collapse
Impossible to say no. It appears on the screen counts down and automatically restart.
All is correct. I have rooted the device and i have frozen the process that causes update.
Now I can say that everything is correct.
Very thanks!