So let's start this thread by saying I was stupid.
In my desperation to upgrade my ROM I went and flashed my Focus with the new Omnia engineering rom. Stupid yes but it flashed. The reason I did it was non of the Samsung focus retail Roms would flash with the WP7 flashing tool not even the jK2 ROM. Which is suppose to be the basic 7004 ROM.
Every time I flashed it would say "This Rom does NOT match the device" or "this device is NOt retail."
So let me just state I had the "RTM Mango" flash on my device already flashed and worked. I was trying to upgrade the firmware and radio stacks. The phone aways worked and was NOT a demo device.
I have tried to flash:
1. jK2 stock Rom same error as above
2. Rom for v1.4 won't work same error as above
3. Rogers Rom on my AT&T focus same error as above.
Basically the only rom that flashed was the engineering rom for the Omnia.
Now the phone boots (with a Omnia splash screen ) I can get it to download mode I can even use the phone just none of the buttons work! I really just want to get a Samsung focus rom back on don't care if it's not Mango at the moment.
My questions:
1. Anyone got an engineering rom for the focus seems to be the only Roms that can load on my device
2. Anyone got some advise to get it back to a Samsung focus rom?
I know I shouldn't have but it's done and can't cry over spilt milk.....
I would really appreciate the help.
What OS version did you have before and what revision of the phone is it?
Thank you for your reply I appreciate it!
If I used the diagnostic menu to check the Revision it said HW:1.0 which is weird as I thought there was only HW1.3 and HW1.4...
Is there any other way I can check to confirm for you?
I had Mango RTM on it the internal MS one that was leaked to the net. It was mango but the Firmware and Radio stacks where accent! That's why I was trying to flash the bugger.
Any idea?
If I look at the sticker behind the battery it says:
REV1.3
The Diag menu also allows one to check the HW and SW version from the Diag menu it said HW = RV1.0 The sticker on the phone says REV1.3'
Would you like a picture of the sticker?
Why in the name would you flash an entire rom ( bootloader, CSC?)
What's the Omnia7 Rom that you flashed?> details, link?
If you flashed the bootloader from Omnia it could mean a lot problems... because it screws the values for the buttons, and I mean it, you'll no longer have VOL-/+...
Thy to get a Samsung jig to see of you can put it in download mode
---------- Post added at 07:11 PM ---------- Previous post was at 07:05 PM ----------
You should've searched....
http://forum.xda-developers.com/showpost.php?p=11197071&postcount=1
Hi all,
I recently bought a samsung focus through ebay but the phone was stuck in demo mode and I wanted to get rid of the demo.
What I have done is: I flashed the phone with the XENJK1 rom for omnia 7.
now the phone works perfect except these problems:
"down" volume button increases the volume instead of decreasing it.
"up" volume button does not do anything at all.
back button sometimes does not work
start button is not working at all
the accelerometer orientation of the screen is opposite than it should be!
any one got any idea how to fix these?! please!
Click to expand...
Click to collapse
Try to keep pressed the Vol- and power to see if it comes to download mode...otherwise use the 300k ohms JIG...
myphonerules said:
If I look at the sticker behind the battery it says:
REV1.3
The Diag menu also allows one to check the HW and SW version from the Diag menu it said HW = RV1.0 The sticker on the phone says REV1.3'
Would you like a picture of the sticker?
Click to expand...
Click to collapse
No need. I think I got the picture.
Let me guess: you bought the phone on eBay or similar?
I think the previous owner hacked and forced the bootloader of the engineering rom that was previously leaked before the 7004 roms on the phone. The problem is, once there I don't know how you can go back to the original bootloader. I suggest you post this in the general WP7 forum and someone (like ansar) might be able to help you.
I know I was stupid!
I can get it into download mode easily no problem. The problem I have is even when in download mode and I use:
WP7 Downloader 7.05, 7.21 and the one I used to flash 7.41 I still get the error (with the normal UJK2 or even the Rogers ROM's)
"The Device does NOT match with the selected binary"
I have tried the "Phone" alone the "Phone Boot" alone both together and even ESC, PDA etc together and alone (basically every option and combination) with the same error message every time "The Device does NOT match the selected binary"
This is true for each of the WP7 Downloaders (so its not a WP7 Downloader issue).
When the phone had Mango (used the update to mango with the leaked MS internal RTM bits) and I tried to get it back to 7004 with WP7 Downloader and UJK2 or Rogers I would get the EXACT same error.
I am not sure what it's doing, maybe I need to find a Focus engineering flash for the device?
The only flash that worked was the engineering flash for the Omnia.
EnderPsp said:
No need. I think I got the picture.
Let me guess: you bought the phone on eBay or similar?
I think the previous owner hacked and forced the bootloader of the engineering rom that was previously leaked before the 7004 roms on the phone. The problem is, once there I don't know how you can go back to the original bootloader. I suggest you post this in the general WP7 forum and someone (like ansar) might be able to help you.
Click to expand...
Click to collapse
I hope they wont mind the double post but here goes thank you for the replies so far!
BTW it wasn't a EBAY phone At Teched 2011 in Atlanta we attended a ATT event and they gave away "Used phones" I got a Focus. Worked perfectly till I was stupid
myphonerules said:
I know I was stupid!
I can get it into download mode easily no problem. The problem I have is even when in download mode and I use:
WP7 Downloader 7.05, 7.21 and the one I used to flash 7.41 I still get the error (with the normal UJK2 or even the Rogers ROM's)
"The Device does NOT match with the selected binary"
This is true for each of the WP7 Downloaders (so its not a WP7 Downloader issue).
When the phone had Mango (used the update to mango with the leaked MS internal RTM bits) and I tried to get it back to 7004 with WP7 Downloader and UJK2 or Rogers I would get the EXACT same error.
Click to expand...
Click to collapse
It's not porper download mode then... or your device is an engineering sample
WP7_Downloader_Ver_7.05_for_Retail_Device_(Product_Force_Select_MD5_X).exe should flash regardless of the phone id...
What do you see if you go to settings>about>more info?
Ok so tried 7.05 and get a error of: "This Device is NOT a retail device" - HUH?????
How can it not be a retail device I have been using it for ages and even updated it to Mango...
OK About info:
OS version: 7.10.722.68
Firmware revision number: 2424.11.8.2
Hardware revision number: 3.15.0.4
Radio software version: 2424.11.7.2
Radio hardware version: 0.0.0.0
Bootloader version: 5.8.0.8
Chip SOC version: 0.36.2.0
Any other info you need?
What are the values on more info screen?
htc9420 said:
What are the values on more info screen?
Click to expand...
Click to collapse
OS version: 7.10.722.68
Firmware revision number: 2424.11.8.2
Hardware revision number: 3.15.0.4
Radio software version: 2424.11.7.2
Radio hardware version: 0.0.0.0
Bootloader version: 5.8.0.8
Chip SOC version: 0.36.2.0
Is there something I am missing?
myphonerules said:
OS version: 7.10.722.68
Firmware revision number: 2424.11.8.2
Hardware revision number: 3.15.0.4
Radio software version: 2424.11.7.2
Radio hardware version: 0.0.0.0
Bootloader version: 5.8.0.8
Chip SOC version: 0.36.2.0
Is there something I am missing?
Click to expand...
Click to collapse
These values are AFTER you flashed the engineering ROM from Omnia?
Yes sir! this is what I am getting now when I boot my Samsung Confusion (Focus\Omnia) Settings>about>more info
Is it developer unlocked ?
It is very strange that you got an unsigned FW to flash on your device but you can't a signed one , that really tells me that you're holding an developer device.
The way I see it :
1.Do you have a ZUNE backup? try to restore from it.
2.Try to download AGAIN the ROMS ( ATT& ROGERS), try to run the WP& downloader 7.05 on ADMIN mode
http://forum.xda-developers.com/showpost.php?p=14875358&postcount=1
3.Try to EMAIL Samsung and ask them what's up with the device, tell them you used ZUNE update and have them check your IMEI.
From the values you posted, the radio HW is missing the version, the bootloader is newer,....
Yup well it was DEV unlocked when I had it as a focus and Mango, I own a Dev account
Yup signed ones it's saying NO - Is there NO unsigned FOCUS rom I can get onto this monkey phone?
I will try redownload the ROM's
I am running WP7 in Admin mode and even in Windows XP SP3 mode ....
I do have a Zune backup but will it pick my phone up as a Omnia or the same Focus?
myphonerules said:
Yup well it was DEV unlocked when I had it as a focus and Mango, I own a Dev account
Yup signed ones it's saying NO - Is there NO unsigned FOCUS rom I can get onto this monkey phone?
I will try redownload the ROM's
I am running WP7 in Admin mode and even in Windows XP SP3 mode ....
I do have a Zune backup but will it pick my phone up as a Omnia or the same Focus?
Click to expand...
Click to collapse
The backup will restore to the stat when you made the backup. I suppose that was a correct Focus rom.
2424.11.8.2 >> this version tells me you're on Focus you might get lucky with the backup....
On the other hand, what's NOT working when you're running the Omnia7 Rom?
The 7.05 should FORCE the flashing no matter what...unless you have a diff NAND layout than the other Focuses ( this is why so many bricked Omnias), it's the only check that could spit the binary error, it this case you're pretty hopeless...you need to get an pit file and only God knows where you could get it from...
Related
Hello,
I want to flash my device with 1.66.707.1 rom. I can't download it via HTC official page.
Now I have few questions. According to that I couldn't download it from HTC official page in my country because I've got inappropriate S/N. May I install it on my radio if I supply good (fake) S/N to official HTC page?
I even didn't tray to do this because I'm afraid I can turn my HD2 a into brick.
I don't care about language. I think that after flashing ROM I can download a proper language pack.
Greats.
invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl threads.
Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?
read this then, it has all the info you need on flashing your phone...
http://forum.xda-developers.com/showthread.php?t=609477
once HSPL is installed you can download an official WWE ROM from this thread and run it as if it were an official ROM for your phone...
http://forum.xda-developers.com/showthread.php?t=623283
y0yster said:
Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?
Click to expand...
Click to collapse
As EddyOS stated, go read my flashing guide THOROUGHLY!!
1. Install HardSPL on your device (best done using WindowsXP or Windows7 32bit).
2. Download the Rom you require from the download site provided and flash using the instructions provided in my guide.
3. Enjoy your new phone
Once you have HardSPL on your phone it will be protected from bad flashes and you will be able to flash stock or custom roms or radios as and when you require. HardSPL is definitely reccommended as it has probably saved hundreds of phone from being turned into paperweights when flashing a bad rom or flashing incorrectly.
If you want to try a custom rom then I would definitely recommend the one in my signature but its totally upto you what you decide to put on your device.
With regards to the 576MB Ram it does seem that its actually accessible but only using the newer 2.02 Roms with specific Radios. This has been tested and verified. It wont be accessible on a 1.66 stock rom though.
Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.
y0yster said:
Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.
Click to expand...
Click to collapse
- What ROM were you trying to flash and what ROM version (and language) do you have on your device?
- Is your device Branded?
- Did you flash HSPL?
- Did you see a progress bar on screen when flashing, or just the colored bars?
- When you get to the tricolor-screen (bootloader) and you connect to your PC, does it say USB after a few seconds, or does it say Serial?
- What went wrong at 24%? Did you unplug the phone, did your system crash, or were you just being inpatient?
If you answer the above questions, someone may be able to help you. Also, start by reading the stickies.
Rom was 1.48.479.1 and I wanted to replace it with 1.48.479.1 because some bugs were annoying me which I mentioned earlier.
Yes my device is branded but it doesn't have simlock.
No I didn't used HSPL because I downloaded rom from HTC using my own original S/N.
When I was flashing I saw brogress bar with HTC logo.
I have those tri-colour screen when I power on the device, but before that I have warning triangle. No it doesn't say Serial nor USB.
What went wrong. I swear I don't know. No, no, no I wasn't impatient. After it hanged on 24% I got error message from the program on PC with UPGRADE ERROR. I've tried to resume like the program said me. But without any effect. What I did was unplug; put aut battery; wait 3 seconds; put battery in; power on and plug in. I'm sure that I was doing everything right because I was following the program.
help
samsamuel said:
invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl th
hi there i really need help
i have a htc hd2 uk on t-mobile tried to rom update and messed it up , things dont work , i would like to ind software to rom update even htc.com s/n not right message comes up . please help
Click to expand...
Click to collapse
If i have 1.48 and with my serial can`t download 1.66... it is recommended to install WWE 1.66 with serials posted here without HSPL? my device is also WWE and was only sim locked Vodafone. (non-branded)
If you have questions regarding rom or hardspl flashing please ask in the correct thread.
if,when you put your serial into htc website, it doesn't allow you to download, then you MUST use hspl to flash an unbranded rom.
@y0ystet. your phone is branded. sim lock its not connected to vendor lock.instal hspl and try again, same rom.
@lakhbeer, did you flash hspl first? more detail please, messed up? doesn't work?
@rayman your phone is vodafone locked.
I repeat, the htc website doesn't accept your serial, you are provider locked and that is not connected to sim lock/unlock.
I sent an e-mail to HTC about that. They said I can send the phone to them.
I found sth out. If I hold the volume down and connect the usb cable I have a message on my screen. On screen which have three colours on green I have: "Upgrade Rom code error. Please try again" And on the white I have: "Serial".
Is there anything I can do about that?
But don't say me to flash witch the HSPL. I won't do that on two reasons:
I've never do that
If I send it to service I'll void my warranty.
What would you suggest to do?
I've solved the problem .
you going to let people know for future use?
How to fix ROM error on VODAFONE UK solution
I also have a HTC HD2 bought from Vodafone.
I flashed my mobile and installed Pandora 1.4 ROM...it was always freezing my Leo every time I looked at docs tab, so I decided to install shipped Leo ROM 1.66 and that is when things went wrong, same problem as you have now, so I downloaded h**p://w w w .4shared.com/file/205652004/1bf6c7ce/RUU_Leo_Vodafone_UK_1434051_Ra.html
aka the original ROM from Vodafone UK and it is working now....but now I am no sure if I wanna try more roms because next time I can be stuck with error screen forever.....
Hi Guys,
I just bought a new AT&T Samsung Focus SGH-i917 from eBay Then Sim-Unlocked it via an Unlock code also bought on eBay.
The device is on 7390 and has Hardware Rev 1.3. I asked the seller whether he updated the phone to 7390 but he had no clue about the same and therefore arises my query.
I wish to CHEVRON unlock this device but am afraid whether it will screw up the device if I flash it with 7004 ROM.
I have been reading regarding the whole process of going to 7004 unlocking the device then preventing re-lock, diagnosis etc. But the more I read the more I got confused.
So, if someone could guide me or link me to a step by step NOOB guide regarding Flashing, Unlocking, Preventing Re-Lock, and updating to Retail Mango update will do me a world of good.
Thanks.
Device Information:
OS version: 7.0.7.7390.0
Firmware Revision Number: 2103.11.3.3
Hardware Revision Number: 3.1.0.7
Radio software Revision: 2103.11.3.3
Radio hardware Revision: 0.0.0.3
Bootloader Version: 5.3.1.6
Chip SOC version: 0.36.2.0
Check my post here, should contain all you need.
EnderPsp said:
Check my post here, should contain all you need.
Click to expand...
Click to collapse
Thank God at least someone did a Noobish guide.
I will try it but first could you tell me can I flash to 7004 as its pre-installed with 7390.
Secondly, I plan to install a micro SD in 2-3 days so I should 1st install it and then go ahead with unlocking, Right?
Thirdly, Flashing phone will in no way affect Phone's functioning?
Thanks
Also please tell me the procedure to take back-up of my current firmware.
bhutoria_1989 said:
Thank God at least someone did a Noobish guide.
I will try it but first could you tell me can I flash to 7004 as its pre-installed with 7390.
Secondly, I plan to install a micro SD in 2-3 days so I should 1st install it and then go ahead with unlocking, Right?
Thirdly, Flashing phone will in no way affect Phone's functioning?
Thanks
Click to expand...
Click to collapse
All good points, including backup. Will add to the guide.
Now:
- Micro SD card add just after flashing 7004. Recommended to format the card beforehand with Fat32 (32K or 64K clusters). Then hard reset the phone from (Settings/About/"Reset your phone") or the buttons combo (see wiki).
- Flashing doesn't affect in any way Phone's functioning as long as it's not interrupted or the phone doesn't have a hardware fault. Recommended to flash the phone on a laptop or a PC+UPS.
- To backup your current firmware read here.
I am new to Windows Phone and require help flashing a custom rom onto my phone. I have dev-unlock but only being able to sideload 3 apps at a time just isn't enough for me.
I've read through a few threads and they've only confused me more, If someone could help me I'd appreciate it.
I have a: HTC7 Trophy T8686
PC40100
OS: 7.10.8170.79
Firmware revision num: 2250.21.51201.401
Radio software: 5.69.09.05.a_22.50.50.21U
Radio hardware: A.102.0.D4
Bootloader: 5.12.2250.1(134578)
You need to install HSPL. Go to this thread and find "Last version (R#3)" and click that to download version 3 (it isn't underlined because of XDA's weird style sheet). Even though version 2 and 1 will work on your "Spark" Trophy (you have the GSM Trophy, its codename is Spark. Verzion CDMA is codenamed Spark_W), version 3 has protections to stop OEM drivers for reflashing the bootloader [which breaks things].
To install it, you first need to downgrade your "SPL", the version number is listed as "Bootloader" from 5.12, to 5.10.
Using the SLSPL from from ansar, you should be able to do this...... however, it depends on the branding of your phone. This SLSPL is designed for an unbranded Euro Trophy, so you may need to either: a) Unbrand your Trophy, b) Find a stock rom from your carrier with a lower SPL version.
Without the 5.10 SPL, you cannot install the HSPL software that will let you flash custom roms.
I have write guides on what to do for Spark_W, but have no GSM Spark hardware to work with to write a similar guide.
I highly recommend backing up your phone before attempting any of these things.. since you might end up clearing your data.
Thanks for the info. My phone is unbranded so I'm able to use the SLSPL method by ansar you mentioned. However I'm not sure where to find a Stock ROM that is required for step 3, could point me in the right direction?
Oh awesome, you can skip the stock rom step. Download version 3 of DFT's HSPL now and run it...
Put your phone into bootloader mode and run DFT_RSPL_WP7FG3_LAUNCH.exe, choose the version number that matchs with the displayed SPL version, then wait while RSPL is loaded. This is temporary and is the first step to install the hard coded HSPL. After you see RSPL displayed on your screen, run DFT_HSPL_WP7FG3_INSTALL.exe.. and you be HSPLed and ready for custom roms!
Put the phone in bootloader mode one more time to make sure HSPL is displayed, and if it is, go ahead and flash whatever custom rom your heart desires for your Spark!
Hi guys, I was wondering if somebody could help me.
I just bought a Trophy and wish to install a custom rom.
My device details are:
OS Version: 7.10.7720.68
Bootloader: 4.6.2250.0
I am confused as to what I need to do, should I go ahead and run this:
http://forum.xda-developers.com/showthread.php?t=1195647
Do i need to downgrade anything in order to install the freedom rom? My bootload is lower then the original poster so I am not sure whether that makes a difference.
I am quite new to Windows Phone 7
Thanks,
-c
Hello. Please help me to flash the ROM and downgrade SPL. I'm trying do it with Y cable and gold card tools but no succses. When I make a gold card with micro SD card and card reader the phone dont start updating, but when I try to do it with USB key, Im getting this message loading and later "Not allow". Please help me to unlock this device. My phone:
OS version: 7.10.8107.79
Firmware revision number: 2250.21.51201.164
Hardware revision number: 0003
Radio software version 5.69.09.05a_22.50.21U
Radio hardware version: A.102.0.D4
Bootloader version: 5.12.2250.1(134400)
Chip SOC version: 2.2.5.0
OK I got it worked now ! I'm flashed it with 2Gb USB flash. All what I need is to insert SPARIMG.nbh and goldcard.img and that's it. But where is no step in tutorial to copy goldcard.img to USB flash. Whatever !
GedZju said:
OK I got it worked now ! I'm flashed it with 2Gb USB flash. All what I need is to insert SPARIMG.nbh and goldcard.img and that's it. But where is no step in tutorial to copy goldcard.img to USB flash. Whatever !
Click to expand...
Click to collapse
Hi, i am new to flashing htc rom. Could you send me link to the tutorial you used for the y-cable method. Thanks in advance.:good:
sydraps said:
Hi, i am new to flashing htc rom. Could you send me link to the tutorial you used for the y-cable method. Thanks in advance.:good:
Click to expand...
Click to collapse
This is the recommended "Noob" guide to GoldCard. It shows you how to build a GoldCard by buying parts, where as the old method required you to cut and splice a cable together.
You need a GoldCard to downgrade your bootloader to from pre 5.xx series bootloaders, in order to install HSPL, which then will allow you to flash custom roms.
This method is required for Spark (GSM Trophy models), but if have SparkW (CDMA Verizon Wireless Trophy) you can follow my guide without the need for GoldCard (SparkW can use GoldCard, but its only really necessary for restoring a half-bricked bootloader).
Hi,
Hopefully someone can help me.
bought a used htc spark over the bay.
It says in the beginning german or English,
but when i choose German i can't read the text it's somehow messed up.
Also i can't use Marketplace.(it's in your country not available)
If i try to update it trough Zune it says my Phone is up to date Version 7.0 6341
tried to flash it with goldcart method ( did that with htc Mozart already) different roms but it always says get newer nbf file.
This Phone should be from UK.
If i try with bootloader it shows blue stripes on bootscreen and says no image file, doesn't matter which rom i tried.
Firmarerevision.: 0.70.162.2
Hardware revision.:XC
Radio soft: 5.20.21.09_22.07.21.00U
radio hard 2.102.0.d4
Bootloader 0.70.2221.2
chip-soc 2.2.2.1
Thanks...
English HTC
I also bought such a Phone over Ebay with the same SW Version, a fully crashed Phone !
I found out that the Phone is a HTC "Test Device" with a special Debug Software on Board.
I talk to someone in the Vodafone Service Center UK. There is a special hardware inside, the only way to change is by programming the build in Chip by special Programmer.
Is there a branded nr. on the Housing ? begining with E20xxx ?
N26Wolf said:
Hi,
Hopefully someone can help me.
bought a used htc spark over the bay.
It says in the beginning german or English,
but when i choose German i can't read the text it's somehow messed up.
Also i can't use Marketplace.(it's in your country not available)
If i try to update it trough Zune it says my Phone is up to date Version 7.0 6341
tried to flash it with goldcart method ( did that with htc Mozart already) different roms but it always says get newer nbf file.
This Phone should be from UK.
If i try with bootloader it shows blue stripes on bootscreen and says no image file, doesn't matter which rom i tried.
Firmarerevision.: 0.70.162.2
Hardware revision.:XC
Radio soft: 5.20.21.09_22.07.21.00U
radio hard 2.102.0.d4
Bootloader 0.70.2221.2
chip-soc 2.2.2.1
Thanks...
Click to expand...
Click to collapse
Yes it actually is...E20xxx...
From an ebay seller also called "wumpie" ..
Thanks, i thought i'm missed something.
So i have to search for which store who fixes this ?
Is that called Jtag, or what do i have to search for ??
Big thanks
N26Wolf said:
Yes it actually is...E20xxx...
From an ebay seller also called "wumpie" ..
Thanks, i thought i'm missed something.
So i have to search for which store who fixes this ?
Is that called Jtag, or what do i have to search for ??
Big thanks
Click to expand...
Click to collapse
Latest Update:
I was sending it to a Programmer. Riff & Jtag didnt't worked.
The Trophy had a 2kb Chip instead of 4 or 8 kb. Even HTC or the official store for flashing the Chip doesn't had a solution.
Anyone before tried to flash some stuff on there an messed it really bad
Thanks to all....
I bought this phone three months ago knowing WP8 was coming out soon. :crying:
I see the XevRev for Spark_W stuff, radio collecctions, tons of custom rom stuff, and etc, but I'm at the point where I'm utterly confused at what it what.
I guess I'm asking where I should start?
Here is what I think might be relevant:
OS Ver: 7.10.8773.98
FW Ver: 2305.13.30202.605
HW Rev: 0003
Radio SW Ver: 1.43.00.06.14_23.17w.05.13U
Radio HW Ver: 3.2.3.D4
Bootloader Ver:3.2.230513.2
Changed DUN NAI from dun.vzw3g.com to vzw3g.com
Just got my dev unlock through dreamspark.
thals1992 said:
I bought this phone three months ago knowing WP8 was coming out soon. :crying:
I see the XevRev for Spark_W stuff, radio collecctions, tons of custom rom stuff, and etc, but I'm at the point where I'm utterly confused at what it what.
I guess I'm asking where I should start?
Here is what I think might be relevant:
OS Ver: 7.10.8773.98
FW Ver: 2305.13.30202.605
HW Rev: 0003
Radio SW Ver: 1.43.00.06.14_23.17w.05.13U
Radio HW Ver: 3.2.3.D4
Bootloader Ver:3.2.230513.2
Changed DUN NAI from dun.vzw3g.com to vzw3g.com
Just got my dev unlock through dreamspark.
Click to expand...
Click to collapse
Well, dev unlock is really unnecessary if you plan on installing an HSPL and flashing a custom rom. Then again, your OS version of 8773.98 suggest that you are running DFT or ansar's rom, but didn't install HSPL (only RSPL to flash the rom). Even with the official rom, your OS level should be 8779.8 after updating via Zune.
First, if you REALLY want to unlock the power of this phone, install HSPL using my HSPL guide for SparkW. It explains every step in detail so you can be ready to flash a custom rom.
Second, give my SparkW rom XevRev a shot for a great Tango experience. Just flash the rom, then update via Zune after setting up the phone to get the newest radio installed. It has FullUnlock and Root Tools, and is the only rom currently around that allows for the phone to be fully programmed using *228 (older roms have an older Xap Deployer package that didn't allow the programing tools to be installed).
You can ignore the radio thread and the "stock like" threads because the contents of those are now outdated with my rom being out.
Get 10+ post under your belt and you can reply to dev forum topics. I'm working on a 7.8 rom, but I won't be able to test it until my third Spark_W comes tomorrow and I transplant a digitizer into it. Maybe since I'm taking it apart I'll also upgrade the SD Card on that one too? (I don't want to flash my primary phone since it's too much of a pain to get reinstalled when I need it for an alarm clock.
Before you flash another rom though, I want to ask you a few things. Do you have Unlimited data via Verizon, and if not, what plan do you have? Also, is tethering working for you NOW before flashing my rom simply by doing the dun nai change? The dun nai change should only be necessary for Unlimited data users.
I'm using factory updates. All I know is that I have my phone updated as far as I can through Zune.
We just switched from AT&T to Verizon, due to the lack of any signal across the entire house. When we went into the store they had to have their manager bring the phone all the way from Kentucky. Anyways, they had just started to push the share everything plan, but the reps acted like they weren't comfortable with those plans yet. I have a 2gb a month, but I called verizon and they disabled the DUN for my phone (as I didn't want charged one of the wifi access fees) When I enabled the wifi after I called them I got a webpage showing I could re-enable it for the $30.
I tried to do the Interop_Unlock but that seemed to not work. But I might as well wait for your 7.8 then.
thals1992 said:
I'm using factory updates. All I know is that I have my phone updated as far as I can through Zune.
We just switched from AT&T to Verizon, due to the lack of any signal across the entire house. When we went into the store they had to have their manager bring the phone all the way from Kentucky. Anyways, they had just started to push the share everything plan, but the reps acted like they weren't comfortable with those plans yet. I have a 2gb a month, but I called verizon and they disabled the DUN for my phone (as I didn't want charged one of the wifi access fees) When I enabled the wifi after I called them I got a webpage showing I could re-enable it for the $30.
I tried to do the Interop_Unlock but that seemed to not work. But I might as well wait for your 7.8 then.
Click to expand...
Click to collapse
Yeah, Interop is a pain to do unless you are running Mango v1. You could factory downgrade to do it.. but its really a big pain.
I'm aiming to have 7.8 and international language roms out by Sunday, work is guna make it difficult. Are you able to use tethering with the dun nai changed though? I'm curious because other users with metered data plans were still having issues.
If you can't use tethering even with the dun nai changed, try deploying JerryJiang's Tethering unlocker for Verizon Trophy. If you still can't tether, I think I know a final adjustment that may need to be made, and you could be a helpful test subject since JerryJiang sent me his apps source code. After I get the details sorted, I can apply the fix directly into my rom without a need for an app (and create a rom package for others to cook into their roms).
TheXev said:
Yeah, Interop is a pain to do unless you are running Mango v1. You could factory downgrade to do it.. but its really a big pain.
I'm aiming to have 7.8 and international language roms out by Sunday, work is guna make it difficult. Are you able to use tethering with the dun nai changed though? I'm curious because other users with metered data plans were still having issues.
If you can't use tethering even with the dun nai changed, try deploying JerryJiang's Tethering unlocker for Verizon Trophy. If you still can't tether, I think I know a final adjustment that may need to be made, and you could be a helpful test subject since JerryJiang sent me his apps source code. After I get the details sorted, I can apply the fix directly into my rom without a need for an app (and create a rom package for others to cook into their roms).
Click to expand...
Click to collapse
Tethering works with the internet sharing in settings. I have no issues what so ever.
I'll beta test if needed. (If it says anything im running win8x86 rtm kinda as my main os)
EDIT
Just saw how big RUU_Spark_W_S_VERIZON_WWE_2.04.605.02_Radio_NV_021 5_NV58008_RELEASE is. I have hughesnet and a 500mb daily cap. I'll have to wait till I'm at my grandparents(I'm 19) where dsl is king tomorrow. lol
thals1992 said:
Tethering works with the internet sharing in settings. I have no issues what so ever.
I'll beta test if needed. (If it says anything im running win8x86 rtm kinda as my main os)
EDIT
Just saw how big RUU_Spark_W_S_VERIZON_WWE_2.04.605.02_Radio_NV_021 5_NV58008_RELEASE is. I have hughesnet and a 500mb daily cap. I'll have to wait till I'm at my grandparents(I'm 19) where dsl is king tomorrow. lol
Click to expand...
Click to collapse
That is the rom for flashing back to stock. You'll need the older rom in the HSPL thread to downgrade the bootloader. Get both roms and back them up if bandwidth is a problem.
So, I finally got to download the RUU_Spark_W_VERIZON_WWE_1.03.605.22_RS0512_2K_4K_hybrid_new_partition_RELEASE and I got it to flash the phone, but now when I try to flash using [ROM_SPARKW][TheXev]XevRev_Beta1a_8835 the phone gets stuck at 0%. I can follow the instructions shown on the program, but it seems to get stuck at the same place.
I can just unplug the phone and turn it back on and i can get calls in the meantime, but it seems I can't proceed.
I tried the dft rom aswell, but it shows the following:
Code:
[Error Description]:
Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.
[Info]: USBWorkRSPL.cpp (235)
[Error Description]:
ModelID is 'PC402000'. Please report this info to DFT.
[Info]: USBWorkRSPL.cpp (234)
thals1992 said:
So, I finally got to download the RUU_Spark_W_VERIZON_WWE_1.03.605.22_RS0512_2K_4K_hybrid_new_partition_RELEASE and I got it to flash the phone, but now when I try to flash using [ROM_SPARKW][TheXev]XevRev_Beta1a_8835 the phone gets stuck at 0%. I can follow the instructions shown on the program, but it seems to get stuck at the same place.
I can just unplug the phone and turn it back on and i can get calls in the meantime, but it seems I can't proceed.
I tried the dft rom aswell, but it shows the following:
Code:
[Error Description]:
Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.
[Info]: USBWorkRSPL.cpp (235)
[Error Description]:
ModelID is 'PC402000'. Please report this info to DFT.
[Info]: USBWorkRSPL.cpp (234)
Click to expand...
Click to collapse
You need to install HSPL before you can flash a custom rom. After downgrading the bootloader to 1.3, you can then install HSPL. Follow my guide here for complete instructions, step by step.
GOT IT!
TheXev said:
You need to install HSPL before you can flash a custom rom. After downgrading the bootloader to 1.3, you can then install HSPL. Follow my guide here for complete instructions, step by step.
Click to expand...
Click to collapse
I finally got it to work! Thanks for the help. I had to find the DFT_XSPL_WP7FG3 that I had downloaded a month ago. The DFT HSPL thread didn't seem to have the file anymore.... When I found that rar, it worked perfectly; I'm now running your 7.8 rom!
I'm still unsure how the WM Device Center actually works, but I'll have to take that up with ultrashot. It seems to work intermittently, I can browse all the files on the phone with the pc that I first set it up with, but all it seems to do on my other pc is just show "error" instead of "not connected."
Its probably because I was trying to do all this on Win8x86.
thals1992 said:
I finally got it to work! Thanks for the help. I had to find the DFT_XSPL_WP7FG3 that I had downloaded a month ago. The DFT HSPL thread didn't seem to have the file anymore.... When I found that rar, it worked perfectly; I'm now running your 7.8 rom!
I'm still unsure how the WM Device Center actually works, but I'll have to take that up with ultrashot. It seems to work intermittently, I can browse all the files on the phone with the pc that I first set it up with, but all it seems to do on my other pc is just show "error" instead of "not connected."
Its probably because I was trying to do all this on Win8x86.
Click to expand...
Click to collapse
First start Zune, then WMDC will start working!
TheXev said:
First start Zune, then WMDC will start working!
Click to expand...
Click to collapse
That did the trick. Been using it for a while now. THe only issues I've had has been with GPSKit Tether. MS Streets and Trips doesn't think that the data is NMEA 2.0 compatable, I can open terminal on the port being used, and it shows data. The only thing I would like to see in your build is the updated start icons. Also I can't seem to get the Nokia Counters installed. I got the files to copy from my ringtones to \Windows, but can't seem to get the provxml file to execute.