Related
WM6.5 on my HD2 (from T-Mobile europe) has finally bothered me enough to decide to change the rom entirely, to android (NAND). I saw the instructions/video tutorial by techburrow (including the magldr v 1.11) and thought that it wouldn't give me too much troubles.
Before starting, I checked my ROM to see if it was recent enough. I as well installed hspl v 2.08 (as shown after taking battery out/in and using volume down + startbutton, in the rgbw screen).
After that I (think I) successfully installed MAGLDR v 1.11. It showed the comment that my phone was now "hacked".
I then went on to the most important step in the process, actually loading android. In the instructions for DFT_Android is states that:
" For installation you need enter MAGLDR (hold power button during boot)"
I tried getting into bootloader by holding the power button, I tried pressing it once and then holding it. Neither worked, both ended up with the HTC logo screen.
All I can do now is choose between getting the HTC logo and the rgbw screen showing hspl 2.08.
Hard reset also doesn't work, probably because MAGLDR deleted the original rom. Connecting through USB via the rgbw screen doesnt work, the connection is not recognised.
Other thread look similar problem, but haven't helped so far. Only the most recent are about others trying to get the android on NAND with MAGLDR 1.11 and DFT-Android.
HELP? Anybody has any idea on how I can install android any ROM now, how to get into the bootloader, how to use my HD2 again?
Looks like Magldr was not flash into the phone. Reflash magldr.
Sent from my HTC HD2 using XDA App
unfortunately
Thx for the suggestion, xhanay. However, reflashing MAGLDR requires an activesync connection and/or USB connection via HSPL (only way my phone does anything). Cannot get any connection unfortunately. So no reflashing.
Any other suggestions? (reflashing via microSD?)
help!i have the really same problem!thx!
This is what I do:
1. Remove the battery, put it back
2. Hold VolDown key pressed while turn on the phone to enter Bootloader (tricolored screen)
3. Connect it to PC and wait for connection to change to USB
4. Flash radio 2.15.50.14
5. Hold VolDown key pressed after reboot to enter bootloader again.
6. Flash MAGLDR
7. Reboot
8. Hold Power button pressed > Select USB flasher ...
....and flash Android/Windows 7.
If USB connection is not recognized I suggest flashing a stock ROM using SD card.
See instructions here, chapter 3 - Flashing Via MicroSD Card
could just work
Thank you for the quick response. Hopefully I will make it all the way to step 8+ (with android and all apps coming along with it). Otherwise using the stock rom should help. Thx for the link.
Will let you know if it works.
Also post in the right section in the future
All worked. I had to reflash a custom ROM through the rgbw screen (apparently a custom ROM did synchronise via USB even though activesync didnt show anything). Then I reinstalled MAGLDR (which immediately sent me through to the bootlader screen). After I had some issues loading android (had to tag USB on in Activesync connection settings, make the connection, the tag USB off in the connection settings)... Now Android is running as I hoped it would. Great work and thanx to all that helped.
ps: Will try to use the right section next time. No promises that it will then be the right one however.
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
dixieuk101 said:
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
Click to expand...
Click to collapse
you could try .... than just plug-it in using activesync and run HSPL3... do not install it...before installing it will put ur phone in bootloader....than exit HSPL3 keep your phone pluged in and just flash wtever....radio,rom...etc....
OR
Press together VOLUME DOWN - DO NOT LET GO! EVER TILL IN BOOTLOADER & RESET RED BUTTON - under batt. metal cover -
after few seconds the tri-coloured screen will appear
load the hard SPL than magledr than rom it works 100%
Same Problem!!!
Hey i have the same problem. Recently I bought this phone off of craigslist. The phone goes to the DFT screen and its on aMAGDLR v1.11. I tried to reset it but it doesnt go to the multi colored screen. I bought a new micro sd but that didnt work. It also cant connect to my computer. There isnt wrong with the charging port because the light goes on when its connected. PLEASE HELP?! I cant go into bloatloader. Is it bricked?
Hi,
I had used HD2ToolKit4.2.0.1.zip and use Wipe option given in the bottom left.
Regards
my volume key not work and now i cant use the bootloader,please
hey anybody here??????????????
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
Click to expand...
Click to collapse
did you do this with right order?
http://forum.xda-developers.com/showpost.php?p=27057672&postcount=127
hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...
Hi All,
I have been running a few NAND Android ROMS but seem to have an issue where pushing the power button on the HD2 no longer locks the phone, it just brings up the Power Off / Airplane mode options etc.
I think the button is damaged and sticking so wanted to go back to stock WinMo ROM to test this and if necisary send back for repair.
I have downloaded the stock O2 ROM from HTC.com but cant work out how to load this ROM. I presume I need to boot to HSPL?? only thing is I cant boot to it, I just get the MAGLDR screen.
Not sure if I'm doing something blatantly stupid or even if the button is not actually broken, although it does exactly the same in all Android builds I have tried. Is there a softkey that can be set to lock the screen?
Any adive much appreciated.
Thanks
Denno
Phone off
hold vol down
tap and release power
keep holding vol down till coloured screen apears
plug in usb, wait for serial to chnge to usb, run the flash.
If you have the 3.14 stock you also need to run hspl4 and choose 3.03.0000
Or
flash from sd card (look it up) will do both the flash and set 3.03.0000 all in one go.
EDIT: I have a guess about the cause of all these issues. It looks as if the phone behaves like the "call" button is being in a pressed state all the time. If the result of the below listed steps is the same when doing them, but with the "call" button pressed, that would confirm it. Can someone please do it?
EDIT2:
Success! Well, kind of. I downloaded Copes CyanogenMod 7 v 02/04/11 [Kernel: AmeriCanAndroid HK853+] SD MAGLDR ROM. I went through all the steps, and then realised there is a rel_path set in startup.txt. I removed it, since I'm doing everything in the sd root directory (as I can't select anything in the MAGLDR menu), and tried to boot. It got past the GO!GO!GO!, and booted Android. Unfortunately, as I feared, the digitizer is not working and I can't select the setup wizard in the dialog that is presented on first boot. I now took the battery out and back in, and it seems the boot process is stuck on htc splash screen, which is shown *after* the GO!GO!GO!. I guess it's all down to hardware now.
--
I got this HD2 the other day in an unbootable state. When I turn it on, first I get the HTC splash screen, MAGLDR menu appears briefly and then MAGLDR 1.13 tries to boot Android form the SD card. However, there is no kernel on the SD CARD, the error about it is shown on the screen and then MAGLDR menu is briefly shown again and the same thing repeats over and over. What I tried is the following:
1) holding down the power button while booting to get the MAGLDR menu, but the same thing happens
2) pressing some buttons -> while holding down the windows button, MAGLDR menu is presented. If I press the volume down button, the loop continues, if I press the volume up button, it tries to boot Windows Phone 7, but it can't find any. If I just let go the windows button, the loop continues
3) putting android on an SD Card - I chose the BoxmaX ROM - I took all the files from BoxmaX.KS.v8.6.KH8.5.1.rar\Android folder and put them to the root of the SD Card - now MAGLDR finds the kernel, boots it, but is then stuck on the GO!GO!GO! line
4) holding the volume key down and pressing end-call button, in order to get to the boot screen and see the radio version and try to flash the WinMo ROM - I can't get to the bootloader, it never shows. Instead I get the splash screen and the MAGLDR as usual
5) come to XDA and ask for help - so, what are my options now? Is there any way to get it to work?
The thing about the phone is that it could have been partially disassembled, so maybe some buttons don't work because of it (I suspect the volume down button, but it reacts while holding the win key). The digitizer too, is probably not responding, but I can't get to any screen where I could be able to test it.
P.S. I'm a HD2 newbie, never had it before, so please forgive any beginners mistakes.
Just a question.. you prefer booting from SD or the phone?
Right now I don't care. I just want to make it do something. In general, I prefer booting from NAND.
Have you try reinstalling magloader?
I'm not at home right now, but for sure we will get this to run... I will give you one big instruction rather asking you single questions... we will start from scratch... 3 steps
Brb 4hrs unless you found your answer
Booting from nand
1. Reinstall hspl... make sure its the right one for your phone. Get in bootloader to do this.
2. Reinstall magloader... 1.13... I believe that's the one...
3. Install a DAF version of rom... then we will get clock work on there since that's the preferred way of flashing rom IMO.
Hope this help you get started... ill keep checking back on you.
Thanx for your help. See my second edit in the first post.
Unfortunately I still can't enter the bootloader, so I can't flash either HSPL, or a WinMo 6.5 ROM.
Notice you say call button seems to be in pressed mode... if that's the cause try to get that fix... to get to it you have to remove digitizer... getting that fix that will help a lot.
I never mess with SD boot so I would not know how to help you in that but if its a nand boot... I know
you might have got the wrong daf configurations or defective hspl or magldr
Have you checked your battery pins to see if one is bent slightly. one of the battery pins being bent has been know to cause boot loops. Worth a good look at the battery pins for sure....
Thank you all for the advice. I disassembled the phone today, disconnected the keypad flex cable, tried powering it on with the volume button pressed and, lo and behold, bootloader screen appeared. So, I'll order a new keypad flex cable, and try it then.
alh84001 said:
Thank you all for the advice. I disassembled the phone today, disconnected the keypad flex cable, tried powering it on with the volume button pressed and, lo and behold, bootloader screen appeared. So, I'll order a new keypad flex cable, and try it then.
Click to expand...
Click to collapse
Ciao!
I have same problem...
But my volume button right works with normal multimedia or phone calls...
Do you think I need too a new cable?
:-?
(excuse me for my english!)
help urgent
can someone help me i got an htc t8585 bouygue telecome french but when i install magldr phone restart successfull and hang on htc logo
how to do? excuse for my english
amsizi said:
can someone help me i got an htc t8585 bouygue telecome french but when i install magldr phone restart successfull and hang on htc logo
how to do? excuse for my english
Click to expand...
Click to collapse
Welcome to the forum. What radio do you have? Switch on while holding volume down and tell us exactly what is on the bootloader screen. I think that is right.
For more info
my bootloader show PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0*05
CotullaHSPL 0*50
I still think it is your radio, see https://forum.xda-developers.com/showthread.php?t=1021837 and https://forum.xda-developers.com/showthread.php?t=611787
I have a strange problem that my hd2 cannot pass the tri color boot screen, even i have replaced the buttons, as i doubted them to causing the problem.
I was previously running android on magldr and it suddenly crashed, since then, i am stuck on tri color. i ve reverted back to the stock from computer and from sd but still the same. Reverting back to hspl2.08, installed many things like task29, clk, mag, custom wm6.5, everything goes fine installation, but the damn cannot boot into any os. I am stuck at tri color screen.
one thing i have noticed that even after i install stock wm6.5, it automatically boots to tri color when connected to a charger, while it is not supposed to do so when mag is removed with task 29 and stock wm or custom.
I am advanced user and have used hd2 for 2 years and i know things like stock and spl and all that. Well i have Tmous with hspl2.08 and radio 2.14.50.
i think this is magldr related issue(since it is booting directly when a charger is connected).
Plz help....i dont want to miss this awesome device while another one of mine is complete brick dead.
.
.
.or is there any command in mtty to ingnore the tri color boot screen and let the os boot??
(note:downloaded the stock wm6.5 from tmous website and installed from computer running win 7 and also tried installing from sd..every installation goes perfect but do not boot)
Check the battery pins, make sure that they are aligned correctly.
Also make sure volume down button is not stuck, try pressing and releasing quickly a few times
Long shot but all I can think of!
Edit: just re-read your post you have tried reverting to stock via sdcard method so
Sent from my NexusHD2 using xda premium
shanman-2 said:
Check the battery pins, make sure that they are aligned correctly.
Also make sure volume down button is not stuck, try pressing and releasing quickly a few times
Long shot but all I can think of!
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
Many thanks but i have tried them previously! Jtag a final solution?
Just had a thought!!
To verify that vol down button is functioning you could install clk 1.5 using the sdcard method,( you need to hold vol down to initiate install).
Go to post 3 here to get insrtuctions.
Then try booting into clk by holding back button when turning on.
Another long shot!!