It happend while I was taking my cloths off for taking a bath
I dropped it inside our WC and my 2GB SD Card was gone far away inside that damn WC and never found it
I tried to pull out the battery but I couldn't pull that damn battery out for 5 min.
Anfter 5 hours drying with a hair dryer I put the battery and other stuff back and there was NO life After pushing the softreset hole some 10-20 times and putting it to charge there was a little life back some blue lines at the screen.
Now after 5 more hours it starts, but after some resets (some times there is only blue lines) and when it starts it freezez very much...
Should I send it for repairing?
Does the worranty covers it? (I bought it from Internet)
Would reflashing help?
Please advice...
tbh, I would have left it to dry normally in a warm place for 24 hrs before even considering to power it up, as (not 100% certain) I think the hairdryer creates static, which could damage the electronics inside, plus, you can't guarantee that it will have dried it out completely, which means, when you started it up, it could have still been damp in the middle and damaged something.
does it look like it has been water damaged? if not, then your best bet would be to not mention that fact, and just say it has suddenly started being funny, not booting up and freezing alot.
I doubt a reflash will fix it, but it is something for nothing, so worth a shot, however long it is.
*edit* if the company won't replace it, you could try your house insurance...
Thanks alot for the reply wytey,
I think there is something damaged, becouse when I soft reset it after freezing there comes a couple of times a light blue screen with blue and white lines...after soft reseting 3-4 times again it loads normaly again but freezez after 5-10 mins again
I was soo happy with my Jasjar >:'(
Your device has been damaged by water.
This is not covered by warranty.
It might not be covered by any insurrance you might have through your service provider.
You may be able to get it covered under home insurrance.
There isn't a case for a wet PDA. But I've read a recent article of getting back a Linksys router that has been soaked wet by rain water. See the real life experience here
http://www.grynx.com/index.php/projects/salvage-your-device-after-liquid-spill/1/
Probably you can do the same?
I dropped my Wizard in the bath, took out the battery and let it dry for about a day or so. Evrything works just fine.. So you should have dry it for over a day or more to be shure no water is left in it
Very timely.
http://www.lifehacker.com/software/hardware/save-your-electronics-from-spilled-liquid-150085.php
V
Thanks for replies guys,
Usefull article, but I think it's too late now, I couldn't take out the battery for 5 mins, then how to open the device and clean the components/circute
Can they prove it if I don't mention water?
Home insurrance would be a big lie, but who cares they get money from me every month (what to say to them? stolen? bropped in water?)
Thanks again for your times guys
I may be wrong , but I beleive there is an "indicator" in most modern equipment that shows up if there has been any water damage
anyone who knows how to repair phones and look at pcb boards etc. will KNOW right away that it has been water damaged. Impossible to hide (unless you yourself are also a technician).
I know because I own a phone repair shop and have been doing repairs for a lot of years.
One of the IC may be damaged, so when your device starts to get warm (as you said 5-10 mins) it cannot hold the power.
Just think yourself lucky that it's only an IC and not a CPU.
E-mail me on [email protected] if you need more help and advice
hb328_dtdd said:
anyone who knows how to repair phones and look at pcb boards etc. will KNOW right away that it has been water damaged. Impossible to hide (unless you yourself are also a technician).
I know because I own a phone repair shop and have been doing repairs for a lot of years.
One of the IC may be damaged, so when your device starts to get warm (as you said 5-10 mins) it cannot hold the power.
Just think yourself lucky that it's only an IC and not a CPU.
E-mail me on [email protected] if you need more help and advice
Click to expand...
Click to collapse
THanks alot for the info hb328_dtdd
If it's an IC, is it hard to repair it? how much would it cost me?
thanks
I (or whoever you decide to check the device) will have to open the unit up and clean out the residue of water and then do thorough tests first, it may not be an IC problem, even if it is an IC problem it may not actually be broken and will work again after cleaning and sonic waves passed through it.
Depending on which IC is broken and how hard it is to replace it, and also if it has caused any other side effects to the other chips, the repair in theory should not cost too much at all as it does not seem serious (from what I read from your post anyway).
E-mail me with more description of the problem and I will try and give you some tips to get it running, if that fails then you can decide whether to send it away or take it to local engineer to repair.
Hope this helps
the Gadget (Ch 5 UK )show did a piece on stuff getting wet. I htink they all came back to life one way or another but the were left to dry slowly I think for a day or 2. so you could hold out for live in the thing yet?
I hate the fact that Dopod 900 is very slippery, don't you think? I'm looking for a rubber casing like the one for O2 and Ipod.
Dopod 900 enclosure is too slippery, I'm so worry I may drop it too.
I am selling some Pocket PCs and this happened to two of my customers. But the device was an Ipaq 37XX and 38XX.
Both devices I put on a warm place and left there for 4 days. Then after this I powered them up. The Ipaq 37XX had only a bad LCD light, which was flickering sometimes and was not bright. the 38XX worked good again.
Anywasys, you need to check your device and have it cleaned. The biggest problem is the fact that there is so little space between smd mounted chips and the PCB that the water stays in between never drying and makes the metal rust. I had this experience with a cell phone already.
So you can try following:
(1) pay for cleaning and repair
or
(2) try to get it guarantee exchanged, which is also possible as for a pocket pc the technicians normally do not check for water damage. But if you have bad luck, somebody will notice this and you get nothing replaced.
I managed the same thing a while ago with my Xda2, and the symptoms were pretty much the same when it first happened (random lines and 'blotches' across the screen, freezing)..
Without haste, I removed the battery, sd card and mopped up any moisture from inside the battery compartment.. placed it in a warm place in an attempt to evaporate the moisture from the device. I left it for 24 hours before powering the device back up.
It DID work afterwards and I was a bit suprised and relieved at its resilience to liquid.
The important thing is to make sure the board and pins of the chips are not shorted by liquid, if you cannot get to the board, evaporation in a warm place is probably your best bet...Just watch out how you apply heat for the sake of the screen (and possibly the keys on the exec).
I dropped my XDA II into a canal and managed to save it. The problem is the water can't evaporate easily. I took the battery off and put it on a radiator. It took 7 days to finally dry out! It worked ok though.
You probably still have water in yours, so I would recommend putting it on a radiator or somewhere hot and just leaving it. You haven't got anything to lose
After almost 2 days inside the radiator it still has the same freezing/dying problem I thinks something is damaged inside ((( And now I can't find any electronic service in Denmark who can repare it
just because it's dry doesn't mean it fix itself, people often mistake this. Sometimes people get their phones to WORK after it's DRY but little do they know what is really happening inside the phone each time they power it back on and the residue is still there inside the phone lurking in the spaces between the pcb and the chips.
no matter what anyone says, I always tell people the same thing:
YOU MUST GET IT PROFESSIONALLY FIXED
My suggestion and this has never failed me yet.
1. After being dropped in liquid, DO NOT SWITCH ON - This is where most of the real damage will occur. If it is/was switched on remove battery as quickly as possible.
2. Strip down and remove any thing you can do easily, covers, sd card, stylus, sim, battery.
3. Waste a whole aerosol of switch cleaner, squirt it anywhere and everywhere you possibly can, literally fill it up with the stuff so it is pouring out of every hole. Do NOT use WD40, it must be electrical switch cleaner that will leave no residue at all!
4. Allow as much as possible of the switch cleaner to drip out and then allow it to dry, do not force dry with a hair dryer and even a radiator is too harsh. I find airing cupboard where the hot water tank is is the best place.
5. Leave at least 48 hours before putting everything back together and switching on, if it does not work straight away, strip it down again and leave another 24 hours, keep repeating for 7 days.
http://www.maplin.co.uk/Module.aspx?ModuleNo=27515&criteria=switch cleaner&doy=29m1
Good luck!
Dear forum members,
2 days ago i spilled some beer on my front pocket, exactly where my HD2 was located. It wasn't much, maybe one or two sips. The water damage seal is still white. I immediately grabbed my phone, pulled the battery out and put it in my other (clean) pocket. When I got home I immediately put my phone on top of the radiator (which i turned down a bit) A day later I turned my phone on again. Everything worked as normal, normal clear boot screen, the intro tune sounded ok, and it even vibrated. I was pretty relieved. The touchscreen works perfectly but only the phone turns the volume up all the time. I can't do anything with the phone because the volume is pernamently raising and thus going to the volume screen. Today I rinsed the volume buttons with demineralised water (very little and careful). The phone is currently drying in a sack of rice. Does someone have any ideas or suggestions how I can fix this issue?
Thanks in advance
EDIT: MY PHONE IS WORKING AGAIN! I just turned it on, the volume was still raising. I don't know why, but something told me i had to suck the "vaporised water" out of the phone. I used my mouth and sucked air out of the small openings of the phone. The phone immediately stopped raising the volume!
You should be able to find instructions for taking the phone apart somewhere around here... I've seen a thread about it I'm almost sure.
Apart from waiting and hoping I don't think you can do much else apart from trying to take it apart and see if there is anything that needs cleaning.
Argh! i just spent the last 20 mins typing up a post and lost it! So lemme try this again...
Ok long story short, I goofed and dropped my s4 into a cup of coffee. It was submerged about 1/3 of the phone , on the top portion of the phone. I removed it immediately, pulled the battery and used a small vacuum to suck out as much of the liquid from the phone before i opened it up. Im pretty good with these kinda projects and have fixed many a phone over the years for friends who busted their screens etc. I hadnt been inside an S4 before this though, so i approached with caution. I used alcohol and a lint free microfiber brush to clean off anything that had coffee on it. All and all everything went pretty smoothly. After cleaning i put the phone in a bag of rice and silica gel for a few hours then put it back together and turned it on. It loaded up quick as usual, everything was pretty normal. But suddenly the screen would stop responding to my touches for a few seconds, and then start working again. So i turned it off, took it apart again and dug a lil deeper. I cleaned off all the contacts for the ribbons, and anything else that had any kinda sticky coffee residue on it. I put it back in the bag last last night and opened it up today and reassembled it. Turned it on , and like magic, everything was great! well 99% great. The phone is acting like it always has,and no more screen unresponsiveness or anything like that. All except for a small sliver of the top of the screen under the Samsung logo. Just a tiny sliver of the screen doesnt respond to my touches, which is a big pain in my butt because its just enough to not be able to swipe down the pulldown menu, and in some games i play, i cant click anything thats on the very edge of the screen in landscape mode. The screen looks normal, no signs of damage like ive seen in other devices when digitizers become damaged etc. Just that tiny little line of screen wont pick up touches.
I only went so far as to taking out the mobo and looking underneath that. I know i can go deeper, and would have to if i needed to replace the digitizer, but before i go through all that, i figured id seek the advice of the XDA Gurus first. Is there possibly anywhere else that i missed cleaning out the junk a that could be causing the problem in that area? Ive been very careful thus far and everything is working accordingly, hell the headphone jack even works still and that thing was full of coffee!! And all the other problems after the initial cleaning have gone away,and im left with this little line of screen that wont read my touches!! So i must have done something right so far! Im hoping that maybe i just overlooked another possible place to clean up any leftover junk and then will get full function of my screen again. if not, then i guess ill be ordering a new digitizer sometime soon.
Thanks for your time, anyone who reads this. I hope to hear some good news *crosses fingers* soon, and get my phone working properly again.
I'm impressed. Not just in your skills but with the build of the S4. Coffee is highly acidic. I once tore apart a keyboard that my wife spilled coffee on. The coffee etched the traces right off the P.C. board. If the S4 survived coffee on the inside workings they use a pretty good coating. It is possible they missed a spot and the coffee got it.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
What a story!!
I bought a galaxy note 4 right on launch day first thing in the morning. Ive had just about every phone but have been waiting for a while now to get my hands on the new note 4.
I ended up buying the phone at the St . Bruno shopping center in Quebec, Canada and once i singed all the papers for my contract and got home, I finally open the box and took the phone out of the box. I loved it, it did everything one would expect from the highest end phone on the market.
A week later however, I started noticing that my buttons, especially my home button were slightly loose and my phone was also developing a weird oil spot under the home button.
So I went back to videotron but this time at St. Catherine street corporate branch store and the manager there obviously didnt know much about phones because he looked at it and proceeded with putting windex on a paper towel and wiping my screen with it and than told me that theres nothing wrong with it.
After frustratingly explaining everything to him, he told me that if the phone makes calls and works, than these issues arent covered for any kind of exchange as its not affecting the functionality of the phone. My logic tell me however that if one buy's a ferrari and realizes that the paint is f-up, wouldn't the dealership do something about it??? Anyways, without any luck I eventually left disappointed.
The following week After exhaustive attempt to solve the matter with Videotron to no avail, I found out that there was a store here in montreal called Service Absolute which is a samsung repair center that I could bring my phone to. I called them first to not waist more of my time and was than informed that yes they could help me but that it could take nearly a month before they would have any parts for this phone.
So after patiently waiting, I finally got a call back from them and droped off my phone the following day. I only had to wait two days before i got my phone back and thought that the turn around time was great! Only after few minutes of playing with it however, I noticed that the phone's new screen which now didn't have the oil spot was actually lifting from the housing about 1mm at the top of the phone and that the buttons were all still loose.
Its easy to imagine at this point how infuriated i was with all the time spent dealing with a phone that should of been right in the first place.. All the waiting, calling and runaround I got only to get a phone that was now even worst!! I could actually see inside my phone and behind the screen. Dust was starting to get inside the phone and under the camera lens and so on and I was really starting to freak out and was completly desperate to fix this issue asap to prevent things from getting worse and worse.
So I decided at this pont to take matters in my own hands and use my old trusty screwdriver to take this thing apart and get
To the bottom of the loose buttons and screen seperation.. I know! Scray [email protected]$ but it had to be done because at this point I needed a working phone for work and nobody seemed to help me. So after watching a few youtube videos, I unscrewed the screws at the back and gently seperated the phone from the metal frame with my fingers.
The whole assembly came out of the metal frame the same komd of way the old HTC phones used to. After doing so, the first thing i found out was that if your going scatch your phones metal frame which makes up most of the phone outer surfice, it's no big deal as it can be swapped out for around 40 to 50 bucks.
Next I noticed that all the buttons (volume and power) aren't adheared to the frame but only clipped in with a few pins stratigically placed. So its normal that they have play and wiggle. They're not gonna break and we're likely engineered to be this way. The wiggling is not really important as it won't affect anything on the phone's motherboard.
The next thing I noticed was that the glue between the inner midframe (the part that holds the motherboard to the screen assembly) also wasn't glued properly and was able to gently seperate it from the lcd/digitizer assembly without a heat gun or anything.. after doing so, the home button fell out and was simply dangling from its flex cable. It wasn't actually glued in place or held in with clips or anything. It's only connected to a flex cable on the left side of the button but thats it. I was easily able to pull it out and inspect it. It was built to be completely free floating between the midframe and the screen.
Which means that again, no need to worry about anything breaking as the home button is not a solidified part to start with and only in place where it is because of the space tolerence engeneered in the screen's home button whole. So it being slightly loose is normal and something that will eventually happen to all note 4's sooner or later. The slight looseness actually makes sense to me as any dust material that will get in between the home button wont get stuck as as much as if the space toleren was less. In my opinion, I thik that iPhones have less issues like this as the home button is part of the screen assembly and is also round.
In the end, I wasn't able to adhear the screen back in place as I didnt have double sided tape but manages to send it back to samsung and get it serviced again. I clearly asked them to fix it properly this time and it looks like they finally did and glued it back properly now.
This was a crazy experience and all I can tell you is that I definatly got an up close look of this phone and decided to keep it afterall as it's still better than a refurbished one and also because it's super easy to repair if anything ever broke on it.
Anyways i know this is a long post but I thought I'd share my experience with everyone and put some of your worries to rest.
Cheers!
Hi all,
last week we had a really heavy rain and I was outside. As a precaution I put my phone out of my front pocket into my backpack only to realize that the backpack was filled with water when I came home.
The phone was swimming in water but still on and working but I had no equipment to open up the phone (damn T3) so I had to leave it powered on and put it in rice over night.
The next day when I tried to boot the phone the screen stayed off and you could see the liquid between the lcd and the digitizer.
I went to a local repair shop and they opened up the phone. I let it dry for some more days but the problem with the display remains.
I washed out the mainboards with iso and cleaned all corrosion I could see with a toothbrush but after replacing the screen it looks like the issue remains.
The phone makes sounds like it is working and giving notifications but the screen is just dead.
Do you have another Idead what I could do or do I need a new phone?
Thanks
crckmc
I am in the exact same boat (almost literally)
I dropped mine into the toilet (how cliche) and it also worked for a few minutes, then eventually the screen went black. I see nobody responded to you here, may I ask what have you ended up doing with it? Replace screen? Get a new phone?