Hi,
After installing wm6(it's up and running great), i have a problem with Active Sync 4.5 on my XP, it gives me an error "USB device not recognised". So i tried to run installation again, when i put BA in Boot Loader mode it comes up with a message "Serial" at the top of the screen and "v2.08" at the bottom.
I have been reading a few threads and from what i see it should read "USB"
at the top.
I have verified that my cradle and PC are working, i have done a clean XP installation and new Active Sync 4.5 install and i still get the "USB device not recognised" error.
Any ideas on how i could solve this problem.
Thanks
USB problem
Is your cradle plugged directly into a spare usb port. (ie NOT a usb hub) It will NOT work if plugged into a hub.
good luck
griffo
when i run HSPL and click next and then its says waiting for USB connection and i connect my hd2 to it nothing happens and then it says error communication timeout error code:0x10001 always reference. ive been stuck on this for a day so if anyone knows whats the problem can you please help me
go into bootloader yourself manually, connect usb, wait ten seconds, right click hspl and "run as administrator"
if still fails keep trying different usb ports.
Use the rear USB ports on the back of your computer (rear mobo panel). The Onboard USB connections did not work for me either.
Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!
check to be sure USB SYNC driver installed correctly and also try a different usb cable.
I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?
exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.
Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?
well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.
Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?
since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)
Hi
my phone is running blisspop , cmw touch is installed . when i try to connect my phone to my PC , error message saying USB device not recognized , and saying device is malfunctioned.
i tried everything.
tried my phone with my friends laptop
changed usb cable
tried same usb with my friends G2 which is working fine. so this is not issue with USB cable.
so i tried to flash kdz to get rid of problem, i entered my phone "Download mode" my pc still displaying same error message.
is it hardware related issue?
It could be a hardware problem. I'm going through a similar case (but it's not a hardware issue though). By default you shold turn off the phone, connect the usb to the PC (not the phone) and then Hold Vol+ and Power, Until you see it entered download mode, THEN you plug the USB port to the phone.
install driver
So I have this strange issue, when i connect my phone windows says "Usb device not recognized" and my phone is just charging without any notification for file transfer option. even tried usb debugging no results. When connected in fastboot mode windows doesnt even show usb device not recognized. no action in windows. I have tried almost all basic fixes and also have replaced the entire charging board. The bootloader is locked.... and i wanted to mod the phone but unfortunately it doesnt connect to pc.