Related
I've got WP7 on my HD2. I want to flash a custom WM6.5 again and then run Android
However I can't flash anything over WP7. CustomRUU says a Error 260 connection
When the phone is plugged in, Zune starts and can see the phone listed. However Windows Mobile Device Centre stays as not connected. I've tried a hard reset i've tried holding the VolDown and power button to no avail.
How can I revert back to WM6.5?
enter inot bootloader than flash
mwang said:
enter inot bootloader than flash
Click to expand...
Click to collapse
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?
geon106 said:
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?
Click to expand...
Click to collapse
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom
JJbdoggg said:
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom
Click to expand...
Click to collapse
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked
geon106 said:
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked
Click to expand...
Click to collapse
You can also rename RUU_signed.nbh into leoimg.nbh and copy leoimg.nbh to your sd-card by using a card-reader, then get your screen in bootloader-mode and follow the instructions on your screen, when the update is completed, give a softreset, that should do the trick.
Regards,
Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.
flashing back to windows phone 6.5
ensure the phone is charged more than 50%
switch the phone off
(at the same time) press the end key (hang up) and the volume down button. this will get you into the tri colour screen.
at the bottom of this screen should be written serial, at this point plug the phone into the pc, the "serial" should change to usb.
on the pc you should hear the usb plugged in confimation sound and the safely remove usb should show a device called "Qualcomm CDMA technologies MSM"
at this point start Custom RUU and proceed to flash the device as normal.
tried to make it as simple as possible
hope this helps.
edit: the tri colour screen everyone keeps talking about is the bootloader
emgp said:
Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.
Click to expand...
Click to collapse
you need HPSL, and no you don't have it cause it would say HSPL 2.xx.xxx
Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.
My fault, its true. In the multicolor screen appears SPL-2.08.0000 .. Now, how can i reinstall the HSPL ? ,if I have installed WP7?.
Exit the Zune program and reflash the Original stock HD2 rom, not the updated 3.14 roms.
Russ
emgp said:
Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.
Click to expand...
Click to collapse
well make sure you have HPSL, then from there power off your phone, but turn it back on by holding down the Vol down button and the power button, and keep holding it till you get to the tri color screen, connect your phone and it should say USB on the bottom of your phone, then from there flash like the regular way.
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
norodaigh said:
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
Click to expand...
Click to collapse
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Well it does boot and if you have hspl you did a good job. So if you have magdlr you now need to install Android. Read a guide plzzz!
Sent from my HTC HD2 using XDA App
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
task29.exe didnt work
Don't do task 29,you will just complicate your life even more than now. I don't think you know what you are doing.
You may brick your phone in the end do you have HSPL?
Sent from my HTC HD2 using XDA App
crisisinthecity said:
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Click to expand...
Click to collapse
1st try entering the BOOTLOADER, by pressing the volume down power button simultaneously..!!!
Instead of TASK 29, try FLASHAHOLIC which will perform your TASK 29 & help you flash a WinMO 6.5 ROM as well..!!!
PS: - You can even flash custom ROM's, stock ROM's not compulsory..!!!
norodaigh said:
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
Click to expand...
Click to collapse
Well then re-install Active SYNC or try on a diff PC with Latest Active SYNC..!!!
If you can access your boot-loader your device ain't bricked..!!!
Just boot your phone with VolDown and enter USB mode, reflash MAGLDR 1.11, once this has completed reboot your phone and hold down the power button, you will then see the MAGLDR menu.
Then just follow instructions on how to install an nand rom
http://forum.xda-developers.com/showthread.php?t=893948
it might just be the magldr or NAND ROM not flashed properly. If you can get to Tri-Color bootloader you are fine.
Found out the problem, thanks for all of your help guys, it was the fact i didnt have hspl2 installed....newb points to me
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
barryhd2 said:
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
Click to expand...
Click to collapse
That's exactly what is supposed to happen if you hold the vol down button while switching on. To get to the magldr menu you need to hold the power button in until it boots to the menu (no vol down button )
You guys are awesome!
I've been avoiding dealing with this phone for a while. This post came up first on google search. Held power and volume (mag 1.11 was on it) and upgraded it to 1.13 and now I'm golden! Thanks guys!!!!!!!!!!!!!
WM6.5 on my HD2 (from T-Mobile europe) has finally bothered me enough to decide to change the rom entirely, to android (NAND). I saw the instructions/video tutorial by techburrow (including the magldr v 1.11) and thought that it wouldn't give me too much troubles.
Before starting, I checked my ROM to see if it was recent enough. I as well installed hspl v 2.08 (as shown after taking battery out/in and using volume down + startbutton, in the rgbw screen).
After that I (think I) successfully installed MAGLDR v 1.11. It showed the comment that my phone was now "hacked".
I then went on to the most important step in the process, actually loading android. In the instructions for DFT_Android is states that:
" For installation you need enter MAGLDR (hold power button during boot)"
I tried getting into bootloader by holding the power button, I tried pressing it once and then holding it. Neither worked, both ended up with the HTC logo screen.
All I can do now is choose between getting the HTC logo and the rgbw screen showing hspl 2.08.
Hard reset also doesn't work, probably because MAGLDR deleted the original rom. Connecting through USB via the rgbw screen doesnt work, the connection is not recognised.
Other thread look similar problem, but haven't helped so far. Only the most recent are about others trying to get the android on NAND with MAGLDR 1.11 and DFT-Android.
HELP? Anybody has any idea on how I can install android any ROM now, how to get into the bootloader, how to use my HD2 again?
Looks like Magldr was not flash into the phone. Reflash magldr.
Sent from my HTC HD2 using XDA App
unfortunately
Thx for the suggestion, xhanay. However, reflashing MAGLDR requires an activesync connection and/or USB connection via HSPL (only way my phone does anything). Cannot get any connection unfortunately. So no reflashing.
Any other suggestions? (reflashing via microSD?)
help!i have the really same problem!thx!
This is what I do:
1. Remove the battery, put it back
2. Hold VolDown key pressed while turn on the phone to enter Bootloader (tricolored screen)
3. Connect it to PC and wait for connection to change to USB
4. Flash radio 2.15.50.14
5. Hold VolDown key pressed after reboot to enter bootloader again.
6. Flash MAGLDR
7. Reboot
8. Hold Power button pressed > Select USB flasher ...
....and flash Android/Windows 7.
If USB connection is not recognized I suggest flashing a stock ROM using SD card.
See instructions here, chapter 3 - Flashing Via MicroSD Card
could just work
Thank you for the quick response. Hopefully I will make it all the way to step 8+ (with android and all apps coming along with it). Otherwise using the stock rom should help. Thx for the link.
Will let you know if it works.
Also post in the right section in the future
All worked. I had to reflash a custom ROM through the rgbw screen (apparently a custom ROM did synchronise via USB even though activesync didnt show anything). Then I reinstalled MAGLDR (which immediately sent me through to the bootlader screen). After I had some issues loading android (had to tag USB on in Activesync connection settings, make the connection, the tag USB off in the connection settings)... Now Android is running as I hoped it would. Great work and thanx to all that helped.
ps: Will try to use the right section next time. No promises that it will then be the right one however.
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
dixieuk101 said:
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
Click to expand...
Click to collapse
you could try .... than just plug-it in using activesync and run HSPL3... do not install it...before installing it will put ur phone in bootloader....than exit HSPL3 keep your phone pluged in and just flash wtever....radio,rom...etc....
OR
Press together VOLUME DOWN - DO NOT LET GO! EVER TILL IN BOOTLOADER & RESET RED BUTTON - under batt. metal cover -
after few seconds the tri-coloured screen will appear
load the hard SPL than magledr than rom it works 100%
Same Problem!!!
Hey i have the same problem. Recently I bought this phone off of craigslist. The phone goes to the DFT screen and its on aMAGDLR v1.11. I tried to reset it but it doesnt go to the multi colored screen. I bought a new micro sd but that didnt work. It also cant connect to my computer. There isnt wrong with the charging port because the light goes on when its connected. PLEASE HELP?! I cant go into bloatloader. Is it bricked?
Hi,
I had used HD2ToolKit4.2.0.1.zip and use Wipe option given in the bottom left.
Regards
my volume key not work and now i cant use the bootloader,please
hey anybody here??????????????
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
Click to expand...
Click to collapse
did you do this with right order?
http://forum.xda-developers.com/showpost.php?p=27057672&postcount=127
First off I'm a noob so sorry if this has been posted before but I could not find it. I flashed MAGLDR 1.2 few weeks ago and then flashed M-deejay's Gingerbread NAND and everthing worked great. Then MAGLDR 1.3 came out so I thought I would upgrade it at this point, now nothing will flash on my phone. When I try to reflash any rom/magldr (anything) it can not establish a connection to my phone. I have a US Tmobile HD2, I can use Win 6.5 and SD Android but can not flash anything to my ROM at all. I hope that any of this makes sense. Thanks
Did you put the phone into bootloader mode?
(Power off, hold down the volume down button and briefly press the power button - keep holding volume down)
And run the flasher as administrator
johncmolyneux said:
Did you put the phone into bootloader mode?
(Power off, hold down the volume down button and briefly press the power button - keep holding volume down)
Click to expand...
Click to collapse
Yes, but even when you flash MAGLDR you have to be in win with activesync, I did that too.
StephanV said:
And run the flasher as administrator
Click to expand...
Click to collapse
I do that too, When I try to flash something it goes all the way to the upgrade button then I press next and it shows the update bar @ 0% and stays there for several mins then goes to a recovery screen. This happens with any flash even something simple like a boot screen flash.
scottzman said:
Yes, but even when you flash MAGLDR you have to be in win with activesync, I did that too.
Click to expand...
Click to collapse
Eerhm, when starting the phone in Bootloader modus, there's no need for activesync anymore.
Start the phone in bootloader mode, and make sure activesync is NOT active on your pc.
Do you still have 2.08.hspl and the required 2.08.50 (or higher) radio? As suggested boot into bootloader and connect to pc. Does "usb" show up on screen?
ClydeB1 said:
Do you still have 2.08.hspl and the required 2.08.50 (or higher) radio? As suggested boot into bootloader and connect to pc. Does "usb" show up on screen?
Click to expand...
Click to collapse
I cant even flash hspl or the raido /edit It was the hspl! THANK YOU sooooo much
What shows on screen when in bootloader mode? Also, does "usb" show up on screen when connected to your pc?
It works! You guys are amazing!!
Glad it worked
hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...