Related
After months of trouble free use my camera dies today. When I try to launch the camera I get the following message "Unable to start Camera" "Unable to initialize camera". I saw an earlier post where the fix was to power down and remove the battery for a few minutes. Unfortunately this did not work for me. I waited approximately 15 minutes before installing the battery and powering up again.
Has anyone elese seen this problem before? And where removing the battery has not helped. I have not tried a Hard Reset. I had a similar problem with my Hermes/838 Pro that was fixed with a hard reset. As you can tell I am trying to avoid the hard reset... I am traveling and do not want to take the time to cutomize my phone, at least not yet.
I am running the original shipped ROM 1.23.707.6
Meanining I have not flashed any ROMs to this phone. It is as shipped from Dopod.
hi i have the same problem since months ... something you have explored? do u have some informations to fix this problem?
Extract this package, and copy all files to the windows directory via Resco Explorer(alle files(.DLL) muts be visible, look at the options of this app) and overwrite the existing files, then softreset, Im not sure if this will work for you, so be sure and make a backup first!
http://www.poigps.com/users/emme/CameraGPS.rar
It really seems a software problem, probably some rom files or registries got corrupted. A reinstall may help, if not, you may still need the ultimate hard reset
I wound uptaking my 810 back to the Dopod service center. The guy said they had to replace my camera. What that means and if that can actually be done I am not sure. I would guess they replaced an entire board. They did re-flash the ROM on my phone as well. Prioir to taking the phone in for service I had not tried to re-flash the rom. I had only done a hard reset with no success.
One side light of my camera going down is... They put the same ROM back on my phone that was previously installed. After the service I have noticed that my GPS gets a "cold" fix much faster than before (twice as fast +/-)
Interesting, I had this exact same error, but on my previous phone, a Samsung D900.
They tried everything, including completely wiping the phone, but nothing helped so in the end they replaced the camera in the phone.
i had this on a tornado
eldaria said:
Interesting, I had this exact same error, but on my previous phone, a Samsung D900.
They tried everything, including completely wiping the phone, but nothing helped so in the end they replaced the camera in the phone.
Click to expand...
Click to collapse
...turned out to be hardware, too.
mainboard error on mine
htc service replaced the camera module twice before they replaced mainboard and cured my phone. I had this problem the first 6 months with my p3600.
Try taking a softreset with the camera on. this worked for me a couple of times
Regards
Possible solution
Possible solution http://forum.xda-developers.com/showthread.php?t=384854
Simply take out battery for at least 15 minutes.
Having the same problem but on front camera ..
Hi,
I having a similar problem but with my secondary (front side) camera. I'm using Dopod D810 with WM6.0.
So, any solutions on this ?
Regards,
Daneal
I have problem Unable to start Camera in htc desire 500
I reset factory but I have this problem. I don't known.what can I do???? please help me
this my number phone 09192561895 in IRAN
I have a peculiar problem here. My O2 XDA Exec was working fine until one day suddenly the D-Pad/nav-pad UP action started automatically and now it runs continuously . So that no matter which application I run, the UP action is automatically emulated. I simply can't use the device. I have soft reseted , Hard reseted and when all failed upgraded the device to WM6 but the problem is still there. I don't know what the problem is. If it can't be fixed, can I some how disable the D-Pad button? Need help, thanks.
You might have something shorting the contacts, if even a hard-reset didn't remove the error. You might have to take it apart to see the problem, or take it to a repair center(not your provider, they will most probably say the warranty has been voided by the WM6 upgrade) to have it fixed...
Good luck with it!
Thanks for the reply, this is what I was afraid of. It will be difficult to get it repaired at a center because there are not many around who can do it well. Since I donot use the D-Pad that much, disabling it by any registry tweak would do for me for the time being, any suggestion on that. Thanks again.
You'll have to ask someone more knowledgeable than me for that...
the buttons are identified by a seemingly meaningless string in the registry, and god only knows which is "D-pad Up". I'm not sure you can even do such as thing in the registry.
It should be easier to remove the lid, disassemble it, and take a good look inside to see if there's anything in there that shouldn't be. You should be able to see the screws if you turn the lid 90 degrees, and from there, it should be a piece of steak...
Good luck!
Uni D-PAD
Hi, Did you get the uni to the service centre ? did it fix your problem
coz, mine is having the same problem too :-(
Ever since I had this HTC Tattoo, I couldn't manage to calibrate the G-sensor and therefore the display doesn't turn when I rotate the phone.
I always get the message "Calibration aborted".
Do you guys have this problem? Did you find a solution for this?
Please help!
Reset phone
Already did it. Still not working.
Did you fix the problem yet, you could try a different rom or even reflashing the one on the phone already.
same problem here.....
I did try a different ROM, still nothing.
Then it could be a hardware issue. If I were you, I would've looked for a replacement.
have you tried holding the phone at a tilt and then calibrating?
lobotomy said:
have you tried holding the phone at a tilt and then calibrating?
Click to expand...
Click to collapse
Yep, I did try that. Still nothing. I think it's just a hardware problem.
I saw this in the Hero forum and I think it might help. There are 2 ways of checking a hardware fault with the G-sensor:
- either the Bubbles game which does not depend on the OS for sensor data
- or the Sensor Debug app.
If anyone of these apps gives you a good response from the sensor, then it is a software fault and you should harass HTC for a software patch. That's what the Hero guys did and it seems to have worked for them (in that case it seemed to be some kind of permission problem with the calibration log file).
Hi,
I have the following issue and would very much appreciate it if someone can help me out or has seen it.
My phone has OliNex 1.56 and Energy Phoenix ROM ( from sometime December I believe )
The issue is that the display does not correctly interpret the clicks on the display. For example I click an button or try to select something it thinks that I've selected the one above it ( or below it - it's random or I cannot figure out the pattern ). If you open and excel file and try to select a cell - it select 1 or 2 above or below it. When I manually align the screen it fixes the issue until the next screenoff or call. Afterwards it's the same thing.
Operating with the phone is a real pain and close to impossible.
I started seeing this about a week ago (haved using the rom for a couple of months ) when I had to take out my SIM card to test another phone. Afterwards it has been like this. ( I haven't dropped the phone or damaged it )
I tried restoring a spb backup from before the issue - it did not help. I then tried flashing with the latest Enerty ROM and did a hard reset afterwards - it it is same. Again it can temporarily be fixed with the screen alignment.
I'm suspecting either an issue with the OliNex or with the HW
Thanks,
-EvilKid
Ive had the exact same problem. Turned out to be a HW problem.
Restored mine back to original (ROM, Radio, SPL) and HTC fixed it in 10days
My friend, your probably are having a problem with the digitizer, you have to send it to HTC assistance so that they can repair it. If it's still in the warranty it's for free.
Moved thread to general section, not rom related. Cheers.
Hi guys,
New owner of a S4 (GT-I9505 international) here with a problem. 2 days ago I noticed the screen wasn't rotating anymore. I used to rotate it portrait/landscape in applications like Camera or Internet (browser). The moment when it started to bother me was when looking at pictures with the phone in portrait and the image was landscape. Trying to rotate the phone didn't help. It was frozen. I called a buddy of mine who has some experience with Samsung devices and told me to verify the "Auto-Rotation" settings. It was all OK and enabled. Then he suggested turning the phone off and pulling out the battery and SIM card for 5 minutes and putting it all back. This didn't help either. Finally we got to the point where he told me to enter *#0*# in the Phone dialing application. As you might already know, this code gives you access to the "testing" hidden utility. There I tested all the options available. Everything was fine except for the Sensors and SensorHub Selftest.
In the Sensors section, all the tests failed, starting with the Accelerometer and ending with the Temperature. I uploaded screenshots taken during the tests. Please remember this started 2 days ago. Before this it was working perfectly. I don't recall making and major changes like updating any OS components or installing/running stress utilities related to sensors or device behavior. After doing some research online and reading about other people's similar problems I got to the point where I started to suspect a problem with the MCU (Micro Controller Unit). This component, according to Samsung, controls all the sensors and reads raw data from them without accessing the AP (Application Processor) this way extending the battery life. I believe the problem is here because it seems odd that none of the sensors are working all of a sudden. Can this component put the sensors into a sleep state and shut them down completely? Might this be the case here?
Below are the solutions I tried in order to revive the MCU and finally the sensors. I was all without success:
1) Turned off the phone and pulled the battery and SIM out. Put the back in after about 5 minutes. Result: sensors not working.
2) Reset to factory-settings from the settings option while the phone was in the working state (turned on). Result: sensors not working.
3) Rooted the phone, installed Clockwork Recovery, made a full system and applications backup and then installed custom ROM (two actually: PACMan, Google Play Edition (4.3)). I did this in order to exclude a problem related to drivers in the stock Samsung ROM, even if it was logical that Samsung being the owner and manufacturer of the device might have the "best" drivers and applications for inquiring the device components/sensors. I am aware this ended the warranty for me, but can I know it can easily be undone. Result: sensors not working.
4) Restored the original stock Samsung ROM. Result: sensors not working.
The utilities used for sensor testing were: Sensor Kinetics and Sensor Tester. Both can be found in the Play Store. On my wives phone, which is an old HTC Desire, both utilities picked up the available sensors and created graphs with the results. On my S4, I only got blank charts/graphics/results. In Sensor Kinetics for the Gyro for example, the message was "Waiting for the Gyroscope sensor...", just that, stuck.
If there are any other guys (or ladies!) out there who encountered this awful experience, please reach out and tell me if you found any practical solution, any other then just taking the device back to warranty. I'm open to any suggestions.
Best regards,
Andrei
Most likely a defective device ... can't you claim warranty and sent it back?
Sounds like hardware failure. This would be an issue for Samsung to solve.
Sent from my GT-I9505
AvelonTs said:
Most likely a defective device ... can't you claim warranty and sent it back?
Click to expand...
Click to collapse
Unfortunately I bought it second-hand and it does not have any warranty. I guess it's one of those moments I wish I had patience and gathered more cash to buy a new one from the store. Anyway, it's my bad luck. I had it working perfectly for weeks after buying it. I will use it like this for the time being..
i´ve got the exact same problem since yesterday...
i think i´ll take it to the shop for warranty
I've got the exact same issue. All sensors are having the same issue. None are working,
I found out because my camera app was not switching between landscape and portait any more. All pictures are saved as landscape...
Called Samsung Netherlands and they told me to wipe my phone (still latest original stock ROM) and try again.
Making a backup now using Kies... and will hard reset it afterward and check the sensors.again.
Probably not going to work... So I have to send it in...
darklord said:
I've got the exact same issue. All sensors are having the same issue. None are working,
I found out because my camera app was not switching between landscape and portait any more. All pictures are saved as landscape...
Called Samsung Netherlands and they told me to wipe my phone (still latest original stock ROM) and try again.
Making a backup now using Kies... and will hard reset it afterward and check the sensors.again.
Probably not going to work... So I have to send it in...
Click to expand...
Click to collapse
Hi there. I had same problem with sensors and MCU test failed, so i took phone to service. They said its hardware failure and replaced main board. Im picking phone tommorow and we will see...
Hi guys,
I took mine to a local phone service, not the official one, but they are an affiliate. They could not figure out exactly what the problem was so they replaced the logic/main board just for testing. It was all working fine. They called and informed me of the findings. Given the fact I don't have warranty for it, they suggested to send it to our main service in Bucharest where they have a more sophisticated testing equipment. It is possible to get a more precise answer regarding the defective component and maybe a less pricey solution to the problem. At this time, the only viable option is to get a new logic board in place, which is about to set me back 250 USD. I will get an answer from Samsung in Bucharest by tomorrow or the day after tomorrow.
I will get back to you with my final solution... hopefully something not so expensive
@darklord, @eweu: please post back you findings. Maybe in the future when some other unfortunate owner finds his way in here, will have a better understanding of whats on the plate for him.
Thanks,
Hard reset did not work as expected. Going to drop it off at a local official repair center....
S4 Sensors failing
I have the same problem with my S4 GT-I9505 device not auto-rotate, air gestures with gyroscope and accelerometer tests failing. S4 been back for 3 weeks to Samsung for repair came back and failed again after 1 week
KSal7506 said:
I have the same problem with my S4 GT-I9505 device not auto-rotate, air gestures with gyroscope and accelerometer tests failing. S4 been back for 3 weeks to Samsung for repair came back and failed again after 1 week
Click to expand...
Click to collapse
After installing some other ROM's and playing with different CSC's I have no sound and even no wireless and only Edge speeds on some ROM's. Restoring from backups, wireless came back and HSDPA+ also, but no luck with sound what so ever. Now, I have a tablet more or less. Thanks Samsung, this is great!
canaris1780 said:
After installing some other ROM's and playing with different CSC's I have no sound and even no wireless and only Edge speeds on some ROM's. Restoring from backups, wireless came back and HSDPA+ also, but no luck with sound what so ever. Now, I have a tablet more or less. Thanks Samsung, this is great!
Click to expand...
Click to collapse
Flashed I9505XXUDMH8_I9505OXXDMHA_BTU, sound and wlan working again. Previous problem with MCU/sensors still there.
i'm tired
canaris1780 said:
Flashed I9505XXUDMH8_I9505OXXDMHA_BTU, sound and wlan working again. Previous problem with MCU/sensors still there.
Click to expand...
Click to collapse
really i'm tired to solve this issue.
when i install new stock software the sensors work fine just a few minutes only yhen return to fail again.
i think its software issue and i'll solve it :good::good::good:
Sensors work again
:laugh: :victory:
Its work right now by itself
:crying:
after uploading the pictures its fail again
abdali_m2 said:
:laugh: :victory:
Its work right now by itself
:crying:
after uploading the pictures its fail again
Click to expand...
Click to collapse
I have the same thing here
all sensors are broken because of SensorHub BIN FW Version: AT0199999
then i try to update firmware with *#2663# it failed.
I have the same problem with my S4 GT-I9505.
Suddenly the device do not auto-rotate, and no air gestures with gyroscope and accelerometer are working.
The SensorHubTest end with FAIL.
Mid december I got one OTA firmware update and I didn't notice any problems first.
A few days after newyear I notice that my auto-brightness adjustment did not work properly.
Can't remember if auto-rotate didn't work when I notice the auto-brightness problem.
But finally I am here because I searched for sensors problems.
I did the SensorsHub Test with *#0*# and it ends with FAIL.
It seems that there is a problem with the 4.3x firmware.
With 4.2x all was fine.
Can anybody confirm my thoughts - that the firmware is broken and not the MCU itself?
What can we try? Downgrade? I read that one was lucky with "factory reset" but it didn't helped to revive the MCU of my device.
Thanks for reading
and answering
___
DK
Hi, i am a owner of a sch-i545 phone, and i have the same problem with the phone: no response of any sensor and a fail on test (or upgrade firmware) of the sensorhub.
At this time i was tried a lot of solutions: i was flashed stock firmware, custom firmware, and of course a factory reset (by the way, the first time with this problem was when i did it a single factory reset), its still broken the communication with the sensors.
I get back to life the phone when i upgrade the phone from 4.2 to 4.3 (sadly) and get lost when i update the binaries in super su (previously rooted with vroot).
Yesterday i give the phone to a technician (a close friend of another best friend), he will test the phone on this weekend to determine what is the problem to try to fix it.
When He fix this phone, i will post any news!
Regards.
remy1004 said:
At this time i was tried a lot of solutions: i was flashed stock firmware, custom firmware, and of course a factory reset (by the way, the first time with this problem was when i did it a single factory reset), its still broken the communication with the sensors.
I get back to life the phone when i upgrade the phone from 4.2 to 4.3 (sadly) and get lost when i update the binaries in super su (previously rooted with vroot).
Regards.
Click to expand...
Click to collapse
Thanks for your answer. I have hope that the next firmware will fix it.
What is strange that none of any reseller/privers know this problem. It seems that also Samsung has no knowledge about this special error.
Well if the next firmware didn't fix the problem, I can replace my model with a working one, that is what the guy at the phone shop offers to me.
___
DK
Same Problem Here
Hi guys, I'm new to this forum so be nice :angel:
I am having the same problem in that none of the sensors are working which indicates that it is a connection issue or the actual hub not working or the firmware and not the individual sensors themselves. I have thought about this and looked around and to me it seems like there are only 3 possibilities for the problem:
1) The SensorHub BIN FW Version is out of date and needs to be updated manually (not through *#2663 as it doesn't work)
2) There is a connection issue e.g. the cable from the sensorhub to the motherboard is loose or broken
3) The sensorhub is broken (not the sensors)
I will try to find the firmware files and see if I can do a manual update. If that fails I will open up the phone and see if the cable is connected/broken. If I still cannot solve the issue, I will have to take it to the shop and hope I can fix it off warranty (I bought it second hand)
Dan
shadowsoulxp said:
Hi guys, I'm new to this forum so be nice :angel:
I am having the same problem in that none of the sensors are working which indicates that it is a connection issue or the actual hub not working or the firmware and not the individual sensors themselves.
[...]
I will try to find the firmware files and see if I can do a manual update. If that fails I will open up the phone and see if the cable is connected/broken. If I still cannot solve the issue, I will have to take it to the shop and hope I can fix it off warranty (I bought it second hand)
Dan
Click to expand...
Click to collapse
Thanks Dan for your reply.
I assume that your S4 shows the same behaviour as my one and the phone is still working fine.
The sensorhubtest failed and your light sensor for automatic adjusting and the sensor for turning the display are not working.
What is really strange that I went to a vodafone shop in Hamburg and ask them if there is any other one having problems with the S4.
You know the answer? They where wondering and telling me that this is wierd and they heard the first time of such an issue from me.
I showed them the device and showed them how I test the sensors. *#0*# funny they didn't know this combo
I hope that you succeed and share your knowledge,
with best regards.
___
DK