Related
Ever since I turned off "Accept all incoming beams" to conserve battery power, and others who have upgraded to the new O2 Exec ROM v1.13.188 (which does this automatically), there seems to be a problem with sync'ing the Universal with the PC via USB with an error message "Windows cannot recognize the device... etc."
A remedy that I found:
1) run the "Wireless Modem" application in Universal (make sure your phone is turned on)
2) select "IR"
3) start and stop the modem
This apparently refreshes the USB, and allows the PC to recognize the Universal again.
Re: USB Sync error msg: Windows does not recognise the devic
heidy said:
Ever since I turned off "Accept all incoming beams" to conserve battery power, and others who have upgraded to the new O2 Exec ROM v1.13.188 (which does this automatically), there seems to be a problem with sync'ing the Universal with the PC via USB with an error message "Windows cannot recognize the device... etc."
A remedy that I found:
1) run the "Wireless Modem" application in Universal (make sure your phone is turned on)
2) select "IR"
3) start and stop the modem
This apparently refreshes the USB, and allows the PC to recognize the Universal again.
Click to expand...
Click to collapse
I have the same problem.
It seems, this problem appears mostly on laptops, not on PCs?
I tried to uninstall\install, repair with all ActiveSync data removal or leaving it - No result.
Also, tried to replace the cable (which is ok, im sure with the one from the camera) - No result.
Temporary and the only way out: do Off\On with qtek9000 on cable connect.
DOES ANY BODY KNOW, HOW TO FIX THIS BUG?? Any Ideas?
Qtek9000 with laptop Toshiba Satellite Pro \ Win XP SP2
EDIT: And, of course, the second workaround - to keep the "Accept all incoming beams" swith ON
are you plugging in via a usb hub? i get this sometimes if i plug in my Exec via a usb port on my monitor. if i plug in directly via the front or back of my pc it generally is ok.
one thing i try is when its plugged in and it gives you that message, turn off the device. it should still be charging. now leave it 10-20 seconds and turn the device on. it then normally "kicks in" for me.
i also find stopping Activesync on the Exec then plugging in the device can get it to work.
theres definately a problem somewhere...
btw i havn't loaded the new rom
i get the problem when I plug in to a hub also, but rarely directly.
if i get it by direct connect, a reset normally rectifies. sometimes i also have reset the pc as well as the ppc
I have recently changed the screen of my Trinity and all was succesfull. the phone works perfectly. However, when I connect the USB cable to the phone, it does not connect to active sync. The phone battery charges though as the orange LED lights on. I am not sure as to whether this is related to the fact that I opend up the phone to replace the screen or whether it is software related. I have tried another phone with the same cable on the same pc and it works so it's definately something wrong with my phone and not the pc. Help is much appreciated. Thanks
Some Thing To Mine
It hapened after a tentative to connect to a exchange server wireless.
Same problem-USB sync not functioning
whenever i connect the usb cable phone to my PC n laptop, both display the error message "usb device not recognize". something must have gone wrong with my d810, how to determine whether it's a software or hardware related problem, my usb charging still working.
open the AS-progam on the Phone and go to the menu (bottom right). If there be an entry "Connections..." open this.
There can be a checkbox "Syncronize all PCs...". mark it and select under this line the USB-Entry.
Now the sync shoult work.
Hi - ever since I used Internet Sharing the other day every time i plug my HD into my computer Active Sync (AS) doesn't recognize it.
When i plug in the phone in I get the touch flo menu and it asks if i want to use AS but nothing happens when i choose this - I've even reinstalled AS and XP has recognised the phone but not AS- anyone else had this problem?
Had this a few times with my other PDAs. In most cases it couldn't get a DHCP address from activesync.
Try this: while its connected, locate your device in Windows device manager (should be "Windows Mobile-base Device ...") and delete it. This does not affect partnerships. Disconnect and reconnect it, and Windows should recognize a new device with proper connection.
6Fg8 said:
Had this a few times with my other PDAs. In most cases it couldn't get a DHCP address from activesync.
Try this: while its connected, locate your device in Windows device manager (should be "Windows Mobile-base Device ...") and delete it. This does not affect partnerships. Disconnect and reconnect it, and Windows should recognize a new device with proper connection.
Click to expand...
Click to collapse
Thanks for the advice however I can't find a Windows device in the Device Manager - i think you are on the right lines though - Windows is simply not recognising the device...
Would it perhaps be USB Mass Storage device?
Windows should recognize your phone, this is independent of activesync. If this does not work, activesync has no chance to connect to, and the reason must be somewhere else.
Check your USB ports. BTW you're not using a hub are you? If yes you should connect it directly to the PC. Check cables, and/or try another USB-device if you have one.
When you connect, you should be asked how the phone should represent to the pc, with options as activesync, harddisk, modem. Select activesync here. If you're not asked, check device settings in Start-settings-connections-usb2pc.
Have you tried blanking out the "enable advance network funcitonality" in USB to PC setting?
And - you are using the HTC supplied USB lead?
bog standard mini-USB cables don't cut it
I recently had to replace my notebook, new one came with Vista, also coincided with purchase of Touch Pro 2.
my current kaiser (WM 6.0) works fine, connect usb, vista fires up mobile device center.
connect pro 2 (WM6.1) via usb , nothing, device center does not start up.
run active sync on the pro 2, Sync button is grayed out. I have set 'sync all pc's....' to usb in the connections screen.
have checked other threads but so far come up blank.
can anyone point me in the right direction to possible fixing this, I need to reload some software not to mention I would like to and would like to check out some of the roms on this sight.
chrisnz1947 said:
I recently had to replace my notebook, new one came with Vista, also coincided with purchase of Touch Pro 2.
my current kaiser (WM 6.0) works fine, connect usb, vista fires up mobile device center.
connect pro 2 (WM6.1) via usb , nothing, device center does not start up.
run active sync on the pro 2, Sync button is grayed out. I have set 'sync all pc's....' to usb in the connections screen.
have checked other threads but so far come up blank.
can anyone point me in the right direction to possible fixing this, I need to reload some software not to mention I would like to and would like to check out some of the roms on this sight.
Click to expand...
Click to collapse
Have you tried starting mobile device center manually? Also had some troubles now and then, reboot of my pc and softreset of my phone usually fixed my problems. Else most responses will probably include the usual: remove all partnerships and/or reinstall mobile device center.
Btw, does your device show up in your hardware list or under my computer when connect it to your USB port?
mobile devioce center (Vista) and htc pro 2
have tried pc reboots and htc reset, no go.
If i connect my kaiser it appears as a device under my computer and device center picks it up.
connect the pro 2, does not appear as a device under my computer and if device center running does not attempt a connect, if device center not running vista does not start it
also no partnerships currently set up.
did have a kaiser one , deleted this when the pro 2 did not connect
chrisnz1947 said:
have tried pc reboots and htc reset, no go.
If i connect my kaiser it appears as a device under my computer and device center picks it up.
connect the pro 2, does not appear as a device under my computer and if device center running does not attempt a connect, if device center not running vista does not start it
Click to expand...
Click to collapse
Well as far as I know Windows should at least show your device under My Computer, even without a partnership or without even having Mobile Device Center installed.
So my best guess is there is some conflict which prevents your TP2 from even connecting to your notebook. Have you tried connecting it to a desktop PC? Or are you trying to connect it through an USB hub or something? If so it is possible the hub isnt delivering enough power.
I had the same issue and ending up hard resetting my phone before I figure what I did wrong. Go to settings on TF3D then all settings. Go to connections, and under usb to pc, select active sync. If it says disk drive it will not work in active sync. Also if the enable faster data sync is checked...uncheck it. Sometimes this causes an issue.
Go to settings and choose USB->PC Settings. Here you can disable "fast synch". Now it should work, if not, activate "fast synch" ^^
YOu might want to re-instal active sync ( device center ), I had a simulair problem, and it was solved
gz reb3lzrr
rodium and vista sync
firstly thanks for the many replies.
still no go
reinstall device center
rebooted pc, reset phone.
tried with a xp laptop with active sync, still no go.
neither pc recognises the rodium phone.
when I attach my kaiser each pc 'chimes' , ie recognises the attachment and activesync or device center start up and connect
rodium nothing.
tried each of the usb ports and couple of cables, all work for kaiser non work for rodium.
Hi. I have had the same problems. Disable fast sync like my man neonoxDE said. That will help you. Altough it helped me. With Win7 you can sync with that option enabled.
(QUOTE: Go to settings and choose USB->PC Settings. Here you can disable "fast synch". Now it should work, if not, activate "fast synch" ^^)
thanks tried that as well, still no joy.
Its has if the phone is not telling the op system that its there. Ie the interupt to the op system that happens when a usb device is attached is not happening, or being ignored.
i had the same problem. i had to uncheck the box advanced network funtions. that wen you go in to settings and usb to phone.
that was the problem with my phone sync.
sorry for bad english.
Ugh
Just went through this all tonight. Also coming from a Kaiser (AT&T Tilt).
To get it functional, I had to:
1.) Add Remove Programs
2.) Remove Windows Mobile Device Center
3.) Remove Windows Mobile Device Center Driver Update (if you installed it).
4.) Disconnect USB from phone.
5.) Reboot
6.) Reinstall Windows Mobile Device Center 6.1 from CD (Sprint here).
7.) Install Windows Mobile Device Center Drvupdate. (WMDC dir on Sprint CD, called drvsomething or other, depending on if you're 64 bit or x86 on your PC).
8.) Then had to "Clear Storage" on the phone and let it clear itself (a simple reset did not let this work)
9.) Once soft reset was completed, I could connect the phone, it then found it, and worked correctly.
Yeesh.
Unchecking the box everyone is saying didn't have an effect for me, though I tried it many times before going all nuclear.
Thanks for this.
Tried this on my vista laptop still no go.
If I connect my kaiser 'installs device driver software' pop up displays and when this is finished windows mobile device center starts up.
Initial connection of pro2, nothing
After having the pro 2 connected for at least 45 mins I did get an an install device driver message, the device was unknown and device center did not start up.
so it appears that the pro2 was recognised has an unkown device
additional info
loaded down a usb moniter onto my laptop.
When I plug in the Kaiser usb monitor shows connection of the device on the specific port.
Unplug this and plug in the PRO2 onto the same port nothing shows as being connected.
rapidlycomming to the conclusion problem with the data pin outs on the USB, does anyone know of a diag program that could test this out or an easy way to check this.
save me the initial cost of checking by a repairer (which in the UK can be steep)
Although my TP2 will sync with USB, most of the time I sync via a bluetooth connection.
Have you tried doing it that way?
Maybe this will work.
One unconventional way to fix this, is to go to your phones activesync. select menu, then change it to bluetooth sync. After that, soft reset phone and connect via usb.
Windows Update
Try conducting a Windows update manually when your phone is connected via USB cable.
Cheers
andrew-in-woking
Something happened with my HD2. USB charging functionality works, but connectivity - not.
Computer shows message "USB device not recognized"
Tried on different comps, XP, Windows 7 - nothing. Soft reset, pulling battery, changing options on USB in Settings didn't help.
Any ideas?
You have ActiveSync (XP/2000) or Windows Mobile Center (Vista/7) installed?
AlexMD said:
Something happened with my HD2. USB charging functionality works, but connectivity - not.
Computer shows message "USB device not recognized"
Tried on different comps, XP, Windows 7 - nothing. Soft reset, pulling battery, changing options on USB in Settings didn't help.
Any ideas?
Click to expand...
Click to collapse
Have you tried a different usb cable?! Anyone you know have a HD2 you can test it out on?! If something doesnt work on my HD2 I try it on my girls just to double check?! When you plug it in do you get a the option of choosing active sync or hard drive?!
Another thing it could be, and I need an answer to this myself, is that when you first plug the phone into the PC, the device presents the option of ActiveSync or Data Transfer, with an option of "Do not show this again". If someone selects Data Transfer, and clicks Do Not Show Again, how can this be reversed or undone? I have a user that cannot Explore through ActiveSync because he likely selected this option.
jimbonics said:
Another thing it could be, and I need an answer to this myself, is that when you first plug the phone into the PC, the device presents the option of ActiveSync or Data Transfer, with an option of "Do not show this again". If someone selects Data Transfer, and clicks Do Not Show Again, how can this be reversed or undone? I have a user that cannot Explore through ActiveSync because he likely selected this option.
Click to expand...
Click to collapse
Jimbo, you can re-enable that in settings-connections-USB to PC, there a checkbox there labeled "ask me first about USB connection..."
DocAlex, did it connect properly in the past? If so, I'd start with toreone's suggestion and find a way to test with a different cable and/or PC.
jimbonics said:
You have ActiveSync (XP/2000) or Windows Mobile Center (Vista/7) installed?
Click to expand...
Click to collapse
Yes, installed. Also tried different cables, one of them was it's OEM cable.
Manipulated with USB setting on phone - didn't help.
Checked wet indicator - it's white.
Did nothing with - on some morning, after full night charging, connected to USB and got it. Bluetooth sync works on same computer...
Looks like USB controller died
Did you try connecting to a different computer?
Thanks Phunkeefunk!
Finally, after and hour on tech support call, T-Mobile agreed to replace it. Already got new, used SPB Backup, very easy transferred all from old one to new. USB obviously works on new.
So - some time USB controller can die ...