Hi,
I dropped my Hermes (belt clip broke) and now I have two problems with it:
1) the keys around the joypad don't work.
2) most of the time the display is just white but sometimes it still work, but the pixels are shifted down about 5 (the bottom 5 lines are at the top.
I checked the Wiki but the service manual has no diagrams in it so I can't troubleshoot to find which PCB is broken. Summed up it just says replace to boards one by one until the problem is solved. I've diassembled it and looked with a magnifiying glass but I can't find a crack. After reassembly everythings the same (yes, I double checked the connections to make sure none were loose). I'm guessing that the break is somewhere in the middle of a multi-layer PCB where it is not visible.
So what I'm looking for is any type of schematic diagrams that will allow me to trace connections. Then I'll know what part to order.
Any ideas?
Cheers
DB
still broke
Hi Mike,
Thanks for the info. I was afraid it would be difficult to get a copy of the drawings. I'm a master electronic technician and have the equipment to to do some testing but it doesn't help to just randomely measure PCB traces without knowing where they go or what signals should be there. The PCB I was referring to is the D-Pad board. It appears to be a 4 layer board, which makes it imposssible to trace manually.
I read the complete 13 page ( http://forum.xda-developers.com/showthread.php?t=349476 ) post about the WSOD but none it doesn't seem to be touch sensitive. It doesn't matter where I put preasure, there is no change.
I don't want to start buying replacement parts on a trial and error basis because that would get expensive if I don't find the problem on the first go. Maybe I'll buy a defective unit on Ebay (or if anyone has one to sell I'm in Germany. PM me) and try from there.
Cheers
DB
Don't know if this will help, but someone submitted some service manuals to my site ages ago.
I just recently replaced part of my Titan's chassis/housing with one I ordered from Brando to fix my failing keyboard. The replacement went pretty much without a hitch but now after replacing *only* the keyboard section my phone's lost the ability to detect the keyboard sliding open or closed. By default, immediately on boot, the screen is sideways - the way it should be with the keyboard open, despite the fact that it's closed.
Has anyone ever gone through this before? Does anyone know where the "slide sensor" is located?
I've dismantled and reassembled the device many times but haven't had this happen before. My only hunch is that the switch probably lives somewhere in the electronics associated with the keyboard itself and that the "new" case from Brando may somehow be defective. I can't test it though as my old keyboard has been destroyed in my attempt to discover why it failed.
Also, I've been scouring the web looking for a service manual for the Titan but haven't had any luck. Mike Channon's collection of manuals is impressive for sure (that guy rocks) but there's nothing for the Titan on his site. Anyone have a Titan manual?
So in my search for information I've looked at just about every HTC service manual available on the web. Going through these I haven't found any devices that are even remotely built similar to the Titan from a keyboard and/or sliding perspective. The closest appeared to be the Hermes but it differs substantially when it comes to the keyboard...
So has anyone ever found a service manual for this phone? Looking at the other manuals is such a tease, given the detailed info found in them.
I do not know how the slide sensor works, but I would guess that it is a magnetic sensor.
If you do come by a service manual for the Titan, please post it.
dmwagner said:
I do not know how the slide sensor works, but I would guess that it is a magnetic sensor.
If you do come by a service manual for the Titan, please post it.
Click to expand...
Click to collapse
I've inspected the entire old keyboard assembly and haven't found anything that directly resembles a magnetic switch but I could be missing something.
Thus far I've Google searched for about 3 hours off and on searching for a service or repair manual and found nothing. I Google technical information all day for a living so I'm pretty confident in my Google skills. Right now it looks to me like nobody's leaked or found a manual yet. I'm really, really hoping that someone here can post one since XDA's full of brilliant, well-connected folks...
=======
Introduction:
=======
Hey everyone, I'm just posting this tirade about my problems with the X1's build quality here in case anyone else is suffering from the same problems I had, as well as some tips regarding disassembling and re-assembling the phone if you're brave/foolhardy enough to attempt repairs yourself, like me.
With contributions from others this thread could become a compendium of common hardware problems with the X1 and how to identify or fix them, as well as pitfalls to watch out for when repairing the device by hand.
I don't have any diagrams yet because I simply couldn't stomach opening up the shoddy device again to take photos.
=======
My X1:
=======
I bought my X1 on eBay second-hand (my first major mistake) so I was always a bit worried what would happen when the day inevitably came when I'd have hardware problems with the phone.
However, I bought it very shortly after the phone's release and the seller described it as unused. The phone appeared mostly unused when I received it, apart from a couple of tiny scratches on the casing.
The phone was functionally fine when I received it and showed no problems whatsoever for the first few months.
Like seemingly everyone my first hardware problems with the phone (I won't even get into the device's software failings) that developed over time were an unresponsive keyboard, cracks in the case and a non-functioning vibration motor.
The 'r' key on my X1 took considerably greater force to register a press than any other key on the device, while other keys intermittently ignored presses or interpreted a single press as 2-5 presses while typing.
The spacebar also intermittently became unresponsive, as did the 'up' key on the front-mounted optical joystick.
The vibration motor worked at first, but eventually gave only a single loud 'click' when the phone should vibrate.
The problems worsened over time and despite taking good care of the phone, the casing started to look badly banged-up - This is not a phone that ages gracefully.
=======
Replacement Parts
=======
In early December I ordered a replacement casing & keyboard from a supplier in Hong Kong on eBay (mistake #2), happyhouse.cn .
The parts were suspiciously cheap compared to the ones from non-ebay suppliers, so I assumed they would be imitation/unofficial parts, not from SE.
At first glance, the new casing and keyboard seemed like the real deal, but when I attempted to re-assemble the phone with the new parts I found that the phone's original screws didn't properly fit the sockets of the new casing and that the new keyboard didn't fit either the new casing OR the old one.
I ended up using a mixture of new and old parts to rebuild the phone.
=======
My Repairs
=======
Over the course of 'fixing' the phone, a few other problems came to light within the device's internals.
A couple of these problems were apparent as soon as I examined the device internally, while others became apparent when I rebult the device and tried to use it.
Keyboard:
The R key on the old keyboard had cracked at first, then eventually split completely into 3 parts during use. One part fell away while the other two remained stuck to the flexible plastic backing of the keyboard structure.
As I mentioned above, the cheap new keyboard did not fit the casing whatsoever (the scale of its design was wrong and it was in total 3-6mm longer than the original part).
I cleaned the original board (the plastic layer with the keys, not the circuit layer) in warm, soapy water and removed the broken R key by plucking it off the flexible backing.
I then plucked the 'r' key off the new keyboard and used it to replace the missing key on the old keyboard, with the aid of some 'Bostik Impact' adhesive.
I finally refitted the old keyboard (with a new R key) to the casing and prayed that it would still work.
It did, in the end, but the R key has less travel and tactile response than the unreplaced keys.
---Tip:---
The unresponsive (or over-responsive) behaviour of the keyboard can primarily be attributed to poor design, but the grit and dirt that enters every keyboard known to man similarly affects that of the X1 and worsens the problem.
Removing the plastic portion of the keyboard unit and washing it in warm, soapy water is a good way to at least regain the functionality that the keyboard had when you first got the device.
Vibration Motor:
I saw the physical evidence of the claim that the camera light LED is badly designed and prone to overheating, in turn killing the vibration motor.
In the original phone casing, the plastic housing that surrounds the LED had melted and resolidified over the course of the phone's life and there was minor scorching on nearby components.
The vibration motor for the device is situated directly beside the LED (to the left, while the rear camera lens is to the right) and seemed unable to function with the melted plastic in its way.
I cleared away the melted plastic but the motor still only 'clicked' when I later tested the vibration.
It seems that the motor gets burned out by trying to work when obstructed by the plastic, or the heat from the LED kills the motor internally.
One way or the other, it's dead.
---Tip:---
The recommendation to not use the light for extended periods of time on the X1 still stands, it's worrying to think of how much worse the damage could get if the light were left on longer.
It is an especially worrying issue when you consider that the light LED is so close to the main Li-Polymer battery of the phone.
Broken Side-mounted buttons:
The next problem I encountered in the original phone casing was that of the weak rubber straps that hold the side-mounted buttons (power, camera, volume-rocker) in place.
These rubber components are quite thin and weak, as well as prone to snapping when stressed.
The purpose of these straps is to hold the button in place (flush-mounted) and to provide the spring action and make the buttons return after pressing.
In my case, the strap holding the power button had weakened and the button stopped working properly, while the phone behaved as if the button was being constantly held in.
The phone constantly brought up the "Are you sure you wish to power off the device?" prompt in WinMo.
When I set about trying to remove the old button to replace it with a new one from my pack of replacement parts, the old rubber strap almost instantly snapped!
I replaced the old button eventually, but even now there is less travel in the button and barely any tactile response when it hits the internal switch on the PCB.
---Tip:---
When re-inserting the PCB during re-assembly, keep an eye on all of the side-mounted buttons to make sure that their inwards-pointing nub sits *above* the PCB and is able to reach the board-mounted switch that the button controls!
Incompatible Screws:
Beware that the screws from the phone's original casing do not properly fit the cheaper replacement casing.
This means that you will have difficulty in forcing the screws to fit (and possibly shear the heads off the screws, which is a pretty major problem in a delicate device like this where they will be difficult to remove).
If you force the screws to fit due to a lack of any replacement screws to use, they will likely not sit properly flush-mounted with the original casing, particularly on the front (touchscreen) half of the device; and this may prove problematic for the sliding mechanism.
Additionally, it means that the casing will not close properly, resulting in gaps between the casing and touchscreen as well as gaps along the sides of the device.
---Tip:---
If you must do your own repairs on the device, try to get the official replacement parts from Sony Ericsson.
Buying the cheaper replacements from eBay is a false economy and a major headache, take my word for it!
Malfunctioning Antenna:
When I first rebuilt the phone after repairs I discovered that I could only get very weak intermittent radio signals in places that I previously had full signal strength.
This problem occured only because of incorrect re-assembly by me, but it represents a pitfall that might catch someone else out when re-assembling their X1.
---Tip:---
When reattaching the Antenna unit (the black shroud that sits around the rear camera lens and which also contains the camera LED), be sure to firmly press on the left side of the plastic (where there are visible metal strips in the plastic) until you hear a click to signify that the shroud is properly attached.
Otherwise, the antennae embedded in the plastic will not properly contact the main PCB of the device and your reception for all radio antennae in the device (GSM, WiFi, etc) will be weakened or lost completely.
This problem was caused solely by my inexperienced maintenance of the device, but may be related to the weak-signal problems some people experience with the X1, at a guess.
Ammendment:
------
I may be mistaken on this one! I had originally thought that this component held the antennae, but after further experimentation I've come to think that the antennae may be housed alongside the speaker unit in the other end of the phone. The tip still stands, just to be on the safe side!
Malfunctioning Speaker/Microphone:
During use early in the phone's life I sometimes found that the phone's main speaker stopped working for apparently no reason and that squeezing the casing 'fixed' the problem until it occured again seemingly at random.
Within the rear plastic portion of the casing that forms the battery compartment there is a small module comprising the phone's primary speaker and in-call mic underneath the plastic piece that contains the SE circular logo.
These components make only surface contact with the main PCB of the phone and are not soldered in-place.
In my case, the small copper contacts that extend outwards from the speaker unit had become flattened somehow within the device and no longer reached their counterpart contacts on the main PCB when the device was closed-up.
---Tip:---
Extending the speaker contacts outwards with a fingernail seemed to rectify this problem for me.
Be sure to tightly screw the module back in when you're done, just to make sure of the circuit-contact.
Touchscreen Ribbon-cable:
This problem was mentioned by others in a thread here: http://forum.xda-developers.com/showthread.php?t=561151
I very rarely encountered that problem in my typical usage of the X1, but after my repairs this issue seemed to become exacerbated (probably due to strains placed on the ribbon cable during my reassembly of the device numerous times).
Currently my touchscreen works as it should in portrait mode, but I cannot extend the keyboard, as this causes the screen to still display a signal, but not respond to any touches.
Upon sliding the keyboard back in, the touchscreen is out of the alignment by about 5-6mm every time until I re-align it under WinMo settings.
In an attempt to fix this problem I covered the exposed portion of the ribbon cable with thin insulating tape, in the hope that this would stop the traces of the cable shorting against the metal casing.
Unfortunately, this hasn't proven enough and I have not yet solved this issue.
It looks as though I need to buy a replacement ribbon cable and fix the device that way.
========================
---Other Tips:---
+ Make sure you have all the tools you need.
Replacement parts come with the necessary tools, but if you don't get those you're going to need a tiny phillips screwdriver, a tiny 6-point star-headed screwdriver and a thin, stiff implement such as a credit card or guitar plectrum to open the casing.
I also recommend a snipe-nose pliers and a tweezers for more delicate parts.
Adhesives & Bonding Agents can be useful in certain applications, but use them sparingly (or don't use them at all, to have any chance of making the phone look untampered for warranty purposes!).
+ Don't expect cheap replacement parts to fit perfectly!
They're cheaper for a reason, you get what you pay for, except in the case of the phone itself.
+ Be gentle with all of the components.
The Xperia X1 feels nice and sturdy when it's assembled, but the individual components can be flimsy and brittle when separated.
Everything from the plastic casing to the circuitry inside needs to be handled with care and treated gently to avoid being broken.
That's everything for now, but if I think of any more issues or tips I'll amend this post.
Please feel free to comment with other issues and any other maintenance tips you've discovered and we can build a useful list for people to refer to.
========================
=======
Conclusion:
=======
Before opening my Xperia I didn't really know what to expect inside.
I'm very familiar with computers and I build my own systems as a hobby, but my knowledge of circuit-level electronics is limited and I have no prior experience of manually repairing devices like the Xperia.
My experiences show that some of the common hardware problems can be resolved by the end-user with some patience and the right tools or parts, but one needs to be extremely careful not to end up with more problems than one started with!
=======
Disclaimer:
=======
I won't be held responsible for any damage you do to your phone and I do NOT recommend that you actually perform any of these procedures.
It is better to let qualified technicians at SE's Warranty Service handle these issues.
I'm providing this information solely for those people who either want to do it or have no other choice to get their phone working again.
The information presented is a combination of information collated from guides that I've linked herein and my own experience but I cannot guarantee their accuracy beyond that.
Treat everything in these informational posts as opinion or observation, not fact!
=======
Links & Other Information:
=======
This post will contain any other helpful information or links pertaining to the disassembly, repair and reassembly of the X1.
This is Cellular Nationwide Network's selection of spare parts for the X1:
http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html
This online store also offers the X1 replacement LCD/Digitizer unit:
http://www.formymobile.co.uk/proddetail.php?prod=x1lcd
I have not bought from either of these stores nor can I verify the quality or compatibility of the items they offer!
I'm just listing them here in case people have trouble finding anywhere to get parts!
=======
Disassembly Summary:
=======
The device needs to be disassembled in the correct order as laid out on this page: http://www.formymobile.co.uk/xperiadisassembly.php
-Remove battery cover, stylus, battery, sim card & micro sdhc card and put them aside.
-Remove the plastic portion of the bottom-rear of the phone (where the SE circle is), using the proper tool, a credit card or a plectrum.
-Unscrew and remove the speaker module
-Remove the screws where the speaker module was
-Remove the covers over the screws at the other end of the phone and then the screws themselves (using the star-headed screwdriver)
-Remove the plastic battery compartment (which also takes the camera cover and stylus slot with it)
-Lift the small black tape and disconnect the plug that powers the camera LED
-Remove the screw in the top-right, then left the black lens-shroud it was holding down.
-Remove the small plug on the ribbon cable at the top-right (this connects the keyboard unit to the main PCB
-Pull the clips around the edges of the green PCB back gently to release it (but do not pull it upwards).
-Lift the PCB gently and (Very) gently remove the orange tape that covers the touchscreen ribbon cable attached underneath, then pry that ribbon cable's connector away from the connector on the green PCB.
-Lift the PCB away and put it aside
-The keyboard circuit and plastic pad can now also be lifted away if necessary.
--- This is where you can stop if your repairs/maintenance only affect the rear portion of the device. Only go further if you need to perform repairs on the front/touchscreen portion. ---
-Remove the four shallow screws underneath where the green PCB previously lay to separate the rear housing from the slider mechanism.
-Remove the four screws in the front portion of the phone, then pry the casing open with the tool/card/plectrum as before.
-The main ribbon cable is attached to a small PCB and some other ribbon cables which are concealed underneath the grey fuzzy foil on the surface in front of you.
-That foil can be removed but it is not necessary to do so unless you are replacing the LCD screen unit, receiver-speaker, front-camera or the ribbon cable assembly itself.
-The Touchscreen component is held down with small grey braided straps at the corners, peel these back to release the touchscreen from the front fascia.
Then do all of that in reverse to put the phone back together!
=======
Videos:
=======
I found these videos on youtube, I didn't record or upload them.
Video guide to Disassembling the Rear half of the device:
http://www.youtube.com/watch?v=AWDurQrRt-Y
Video guide to Disassembling the Front half of the device:
http://www.youtube.com/watch?v=iyGUbxFqvyc
Video guide to Reassembling the Front half of the device:
http://www.youtube.com/watch?v=RcDqyEyC_HY
Video guide to Reassembling the Rear half of the device:
http://www.youtube.com/watch?v=V0sOaIo6724
=======
Personal Comment:
=======
It goes to show that, as many of us are already aware, you must pay a premium price for this phone but it is NOT manufactured like a premium product.
If my situation were rare or I had only one of the above mentioned hardware issues with a new phone I could accept it, but things got ridiculous with the X1.
The build quality is very poor overall and Sony Ericsson should be ashamed firstly for releasing a device onto the market that functioned as little more than a flawed prototype for the X2; and secondly for charging upwards of €600 for the 'privilege' of putting up with its many problems and shortcomings.
I for one, won't be buying any more SE phones.
My next smartphone will be an Android device such as a Motorola Milestone if I ever pluck up the courage to spend that much money on a phone again.
=======
Disclaimer:
=======
I won't be held responsible for any damage you do to your phone and I do NOT recommend that you actually perform any of these procedures.
It is better to let qualified technicians at SE's Warranty Service handle these issues.
I'm providing this information solely for those people who either want to do it or have no other choice to get their phone working again.
The information presented is a combination of information collated from guides that I've linked herein and my own experience but I cannot guarantee their accuracy beyond that.
Treat everything in these informational posts as opinion or observation, not fact!
Useful post, but it really seems that the majority of your issues were caused by the imitation housing that you purchased, not by poor SE build quality. Of all the issues you mentioned, the keyboard issues are an SE/HTC quality control problem, I've experienced them as have many. The rest seem to have been caused by the imitation housing. This begs the quesiton, why didn't you just use SE's warranty service? They don't require a reciept or that you be the original owner. And trust me, they are several times better than HTCs warranty service.
sonus said:
Useful post, but it really seems that the majority of your issues were caused by the imitation housing that you purchased, not by poor SE build quality. Of all the issues you mentioned, the keyboard issues are an SE/HTC quality control problem, I've experienced them as have many. The rest seem to have been caused by the imitation housing. This begs the quesiton, why didn't you just use SE's warranty service? They don't require a reciept or that you be the original owner. And trust me, they are several times better than HTCs warranty service.
Click to expand...
Click to collapse
I'd hardly call the problem of the non-fitting screws a majority! The rest of the issues were unrelated to the cheap replacement housing.
Maybe my post is confusing, but the issues with the keyboard, vibration motor, ribbon cable, side-buttons & speaker all existed long before I ever ordered the replacement casing!
Some, such as the ribbon cable and antenna were issues that cropped up or were worsened due to my inexperienced maintenance, but everything else was a fault of the build quality of the original device.
The incompatibility of the screws was the only problem specifically caused by the new housing, while its own supplied keyboard didn't fit the chassis, but that was a non-issue since I used the original keyboard anyway.
It could be said that my repairs would have gone significantly smoother if I had bought and used an official replacement housing from SE, but that would only solve the issues of the screws and replacement keyboard.
I put emphasis on the problems related to the cheap replacement casing primarily to warn people away from wasting their money on them the way I did.
I'll edit the original post for clarity.
To answer your question, I didn't use the Warranty service because frankly I assumed they would need a proof of purchase for the warranty (since most warranties do in my experience) and I had bought the device second-hand on eBay.
Secondly, sending the device in for warranty would mean going through the hassle of reflashing a stock rom and SPL to the phone.
Thirdly and most importantly, I wanted to try doing it myself for the experience and potential savings.
Obviously, I wouldn't recommend anyone to try and repair their own phone as I did, but if someone has had a phone sent back to them marked as "tampered" by the warranty service and are left with the options of paying for repairs, paying for a new phone, or buying parts and repairing it themselves.. well that option is there and this thread might help them.
Also, off-topic but I couldn't agree more with your signature. I tried a myriad of fancy ROMs and shell replacements for my X1 but never found satisfaction until I flashed a basic blank WM6.5 ROM and installed PointUI Home2!
Thanks this post helped me out, I suddenly lost my mic, took a look under the hood and found I had the same issue as you, the mic pins not touching. The pins are very weak so had to be careful but it works now!
tumpin said:
Thanks this post helped me out, I suddenly lost my mic, took a look under the hood and found I had the same issue as you, the mic pins not touching. The pins are very weak so had to be careful but it works now!
Click to expand...
Click to collapse
Glad to help!
Definitely the most thorough repair and tips guide for the x1. A lot of the issues you had are the same as mine. Thanks to your suggestions I got my phone in almost working condition. Now I just need to find a way to get my keyboard working again.
Sent from my xperia x1 using XDA App
Thanks Zurechial for this thorough post. I for one, have been lucky in finding a repair guy (non-SE) who is an expert with devices like the X1. I had a problem that some water/moisture/sweat had seeped in the charging port and I could not get the phone to charge. He fixed it for me.
Now the only problem I face is that the camera is not working, and wifi is disabled. Any tips to get the Wifi working? It is shown as disabled in the Comm Manager and there is no WLAN MAC Address also for it.
brilliant post, thank you very much indeed. I have just ordered a cheap housing off ebay, i know what to expect now
What worries me the most though, is how the keyboard WILL fail eventually ><
The qwerty keyboard is one of the main reasons why i got the phone.
time to snatch back our lives suckers
Apparently, it's taken less than 20 years, to destroy the Consumer Electronics Industries, ability to Repair products, sold in this country. I saw the writing on the wall, in the early 80's, with the first lines of "off shore", throw away VCR's, that were priced cheaper than they'd cost to repair. The theory, if it breaks, throw it away & buy a new one. Who cares if it winds up in a land fill somewhere.
Now, we're up to $500 Cell Phones, with the state of repair being either, unit replacement, or, cannibalization of parts. And apparently no one cares. Is it our complacency or can we really afford as a society, to buy a new phone every time one breaks? God knows we're all desperate, for our phone usage.
It's time to snatch back the repair ability we once had. This is the age of recycling, and the highest form of recycling is repair.
As consumers, start demanding access to schematics, and, access to sources of component level repair parts.
IM
You help me...
I'm almost freaking out when signal on my phone show only 2 bars...
Anyway...
it's for additional information,
use handscoon, it gives somewhat confident and when using tweezer, hold it like using pen (I learnt it when I studied as paramedic) because it will give me strength while holdin it.
AND ask the seller to send housing with screw. I bought 2 housings, from ebay and another hongkong shop. Ebay is s%ck but that other hongkong shop is more fit.
I've searched far and wide to find a video or tutorial for my problem, but didn't find much.
My problem; my middle button (Windows key) has stopped working - it does work at times but you gotta hit her in the right spot. It does feel like there is some physical damage to the underlying components.
My question is, how would I go about solving this problem? My HTC is out of warranty as far as I know and I've found one person selling replacement keypads in the US (I live in the UK), but is the keypad the correct component to replace or should I be looking to replace whatever is underneath?
Thanks, Az.
Sent from my HTC HD2 using XDA App
I would rather pay money to HTC and make them repair it than buying it my self and doing myself anywayz,. it looks like its a physical problem, the button must be replaced.
If you want to, you can change the button, it's most likely it would be it the one's broken.
I deduce that you might not be too "experienced" with electronics as you were looking for a video on how to change this part or even how to open you PDA (even if I could totally wrong as there are many persons who like to have all the available info before proceeding).
Anyway, even if I haven't opened my HD2 (yet), I don't think it would be a problem, just be sure to be very careful when you open it, prepare yourself with all the necessary tools (little screwdrivers, I think you'll need a torxs T5 screwdriver, platic pliers, etc.), clean and illuminate your working area and proceed slowly without forcing anything.
To work with most of today electronics you'll need a very fine pointed soldering iron (or heavy skills in soldering, but it's better to have both) or two would be better, a magnifying lens lamp, pb free solder (even if you can use sn-pb solder with pb free solder); but all this stuff will be necessary only if you want to change the push button itself. I just saw how to take the HD2 appart and it seems like an "average" PDA disassembling, the only detail regards the final chassis disassembling, they ask to use a oven to soften three adhesive stripes, this could also be done with a good hot air rework station.
At the end, you'll have to decide if you want to change the push button or to change the whole front buttons board.
I hope this helps.
good luck
I have taken apart some many Tmous HD's, thank could do it with my eyes closed. But it is tricky. I think I'll make a video, and then post it.
I deduce that you might not be too "experienced" with electronics
Click to expand...
Click to collapse
You pretty much hit the nail on the head - well, I am experienced, just not any good, being into building and maintenance by trade, I'm more used to smashing and brute forcing rather than using careful precision lol.
I actually forgot about this post - what would you guys say about the volume +/- buttons? They're sticky, would I need to replace those too? And what sort of estimated parts price would I be looking at for both the buttons and a screen? I want to make sure I'm not overpaying. The screen itself isn't smashed, but the the top layer. I know it sounds like I've abused my HD2 in a bad way, but it did this to itself on a night out - I don't know how lol.
I've seen the screen part going for around £20. I have no clue on the bottom buttons or the volume keys. Would I be better off getting a dead HD2 for parts? And are there different part versions as such or are they universal?