I tried looking in the forum for any info on the status LED next to the speaker on the front side but I don't see any posts on this. Is this LED supposed to flash or do something? On my HD it has never worked? Is it supposed to work?
I remember on my Artemis it would flash green for good reception, blue for bluetooth and red if the battery was low.
FrancoBollo said:
I tried looking in the forum for any info on the status LED next to the speaker on the front side but I don't see any posts on this. Is this LED supposed to flash or do something? On my HD it has never worked? Is it supposed to work?
I remember on my Artemis it would flash green for good reception, blue for bluetooth and red if the battery was low.
Click to expand...
Click to collapse
I may be wrong but i was under the impresion that this was a sensor rather than a LED.
No, that's entirely correct, it is the light sensor. The LED is in the power button.
the status led is on the power button on the top right hand side of the blackstone...the place u highlighted is a sensor as what scotia has point out..
I think that it is a proximity sensor used to blank screen when you put the phone on your ear to talk.
It's actually the light sensor used for when you have automatic display brightness enabled. When it's dark, it turns down the brightness... And when it's a sunny day it cracks it up. I am not sure whether it's used to blank the screen during a call... This seems to happen after a period of time has elapsed.
Gav
ok thanks for the info.
So does the power LED on the top side flash any color to show the status of the reception or does it only light up orange when it charges?
Thanks.
doesn't do anything for reception..although mine flashes green hen I have a message/email/reminder
pity though, a decent LED to show such things was probably high on everyone's wishlist
No, the HD is perfectly unobtrusive. On my last PDA the LED had to be tweaked to stop flashing.
Too bad this isnt a LED diode Since I got on my Diamond a light notification (on the bottom of device)... when I recieved new sms... now on HD there is no way I can figure do I have new sms or notification unless I turn the screen on. The only hardware flaw by mine opinion
When its lying down, I agree with you. Then I have to turn on the screen. However when its lying next to me I'm usually not in a place were I can't use my phone, so the sound is on anyway.
I actually think its quite good the LED is on the top, it's easelly visible when the phone is in my pocket. I just have to pull the phone up a little and look down to see the LED (no need to get it out and turn the screen on). I like it on the top, nice and discreet, and not anoying me when I'm looking at the device while using it.
Perhaps a combination would be nice? Front and top That would sattisfy most people I guess...
Ok when looking at the hd2 on top near the speakers the left side. , You will see 2 circles.
What are those ?
At first I though it was the notification led but after using it for more than 3 months I think , I noticed it does not light up or anything , and the light comes from the left side of the speaker it's self, which is not covered and gets dust in and everything
light sensor and proximity sensor....
Oh I see
Thanks
i just noticed when i awnsered my phone for a call one of the two sensors at the top(the one on the Left) turned a dim red light and went off when i hung up. What is that? Is it suppose to be a LED Notification Light like on other phones?
Probably the proximity light sense...the thing that turns the screen on and off when you put the phone on your ear and pull away. To my knowledge there is no led light on the phone oddly enough.
I just installed the Skinomi screen protector so I had to spray a bit of solution. Now the pyhsical buttons doesn't light up unless I make a call. When I press home or menu it doesn't light up.
I have not noticed this but can anyone tell me if it is based on the light sensor. I am in a fairly lit room right now. Thanks
Well I just went into the bathroom and I guess it is based on a light sensor.
I broke my screen a few days ago and had it taken in to be replaced. A few hours after receiving it I noticed the LED was blinking, but in strange colors different than those I set in Light Flow. The normally white notification is now cyan, yellow is now green, purple is blue. Red however doesn't display at all, so it seems that the red portion of the RGB scale is not functioning. Does anybody know what during the screen repair process might be causing this to happen? I'm almost certain its not software related as prior to having it repaired the LED was working correctly. Thanks!
There's a kind of filter for the LED on the display, not all replacement parts come with it and it's pretty easy to overlook.
DrFredPhD said:
There's a kind of filter for the LED on the display, not all replacement parts come with it and it's pretty easy to overlook.
Click to expand...
Click to collapse
There does seem to be a blue hue around the notification light area when held in the light... So could it be that this filter was mistakenly left on the old screen, instead of transferred to the new part? Or is it something attached to the screen that can't be moved from one part to the other?
It wound up being a damaged LED light