I am posting this to share with those who are having mic problems with their HTC Magic.
Currently I am using the Invisible Shield to protect my HTC magic from scratches and such but it was after the application that the mic had ceased to perform optimally (Mic is very soft). I searched through the forum and google itself and the solution is to patch it with 3 files into the system/etc directory. (http://forum.xda-developers.com/showthread.php?t=517745)
But to my horror, no matter how much and how many different variations of the 3 files I patched, the mic is still very soft (tested using google search and voice recording). However, tonight I had finally found the problem and a solution for it.
The mic's located is at the bottom of the device next to the usb port on the right side - externally you can see it as a tiny little hole. If your device protector (i.e. Invisible Shield) is covering that hole, you would be very likely to have "mic problems" as I do then. To rectify this problem, you need to ensure that nothing is covering that part of the device for the mic to perform in full functionality (Either reapply your invisible shield or poke a hole through it)
Good luck and hope this works like a magic for you (as it does for me !)
Related
This is for those of you with intermitent loud speaker problems especially those who have noticed problems when the stylus is inserted into the silo as mentioned here and here. Facing a daunting 4-6 week separation whilst my UK import TyTN was shipped to Germany for warranty repairs, I caved and cracked open the back.
Attached is a slightly grainy closeup (the macro on my Contax U4R sucks) showing what I found. Yes, that's the damnable clear vinyl shim (pink circle) that others have encountered. And that's a loose speaker connection (thankfully not a full blown short as I had feared).
The shim appears to have been jammed by the stylus into the loudspeaker connection (red circle) and unseated the plug 'just so' (burgandy circle) from the mobo. The case was keeping it partially seated. However the case would flex out thanks to the stylus- a condition that was probably exaggerated by the shim. Without the shim my stylus no longer comes out of the silo fully extended- but that's a small price to pay for hearing the phone ring.
In addition to what teambnet says - even if your stylus retaining block of rubber has not come off and hit the connector - that connector (see teambnets picy) is not the firmest and could easily come loose as teambnet says and cause poor/non-existent connection to speaker. Simple fix it's just a push in pull out block connector. Don't assume you have to have given your device a hard knock. Even the odd vibration over time could work this one loose.
This does not of course 100% rule-out, that some folks may have a software issue instead.
Mike
Thanks,
Very useful tip. It fixed my phone
Hi,
The speaker on the outside of my universal (the onw you hold against your ear with when the screen is on the inside) is broken.
That started as something like a bad contact (if I pressed the phone against my ear it would work, otherwise not). Now it is not working at all.
The speaker on the LCD side is working fine.
The advice I want:
I took a look at the service manual PDF I got and disassembling the phone to reach that speaker is a lot of work. I do have experience with diassembling electronic devices and even do some soldering, etc. However, my doubt is this: I have a phone which does work, but the way I like to use it to make calls does not work.
Question 1
Is it worth the trouble to diasassemble the whole device just to check if it is indeed a bad contact due to i.e. dirt? Or will I actually risk breaking something off, which will render the complete phone useless? Looking at the service manual, one needs to use a plastic tool to actually open the phone. How easy do the hinges break off?
Question 2
Has anyone had a similar problem? Was it easy to fix?
Thank you!
Cheers,
vma
you dont need to disassemble the whole phone just disassemble the screen . It isnt that hard to do, just remove all the screws from the screen . The screen casing is difficult to budge at first but once you have freed part of it open, the rest follows quite easily.
Hi,
Meanwhile I couldn't resist and opened it...
...and I found the guilty part.
It seems that the outside speaker is actually attached to the case and uses a contact connection to the PCB. This connection is made by to metal plates, which are tiny and folded. They will compensate the varying pressure made on the case (i.e. when you press it) and I guess with time they tend to break at the fold.
This happend to one of the two contacts. First I tried to fix it, but the truth is that it is so small that it is quite impossible to do anything about it. I considered soldering a small wire, but that would require to solder the other end to the pin on the PCB, which then would mean, I could no longer use a regular replacement speaker, if this one had any other fault (unless I could clean the contact again, but trying that, I could break something else, also).
This means: now I am not able to use the outside speaker anymore...
Question: where can I purchase a replacement one? Would anyone sell me one from a broken Universal (for a symbolic price - anything over 10 Euro is too much, as I would prefer to just buy a another second hand Universal)?
And as I was figuring this out, I used the occation to fix that loose stylus!
1) Open the underside case (4 screws, then open the case all around with some thin plastic).
2) Roll a little bit of celotape and place it between the case and the pin that fixes the stylus in position.
3) Try it out until it is OK.
4) Close the case and that's it!
Cheers,
vma
Hi buddy, in fact I did have the same problem that you're having some months ago, my uni fell and since then the problem just got worst, until some day a couple months ago I opened it and fix it.
It's just like you say, the little golden plated contacts wore off, then the little speaker's metal plates just were too high to make any contact against the pcb, it's really simple, just pull the plates gently away from the little speaker, do clean both sides of the contacts (pcb and speaker's plates), i did this with a little xacto knife (be very gentle), and that's it! It worked just fine.
The problem is that in my case one of the metal plates broke off.
I tried to fix that, but it is to small for me to achive anything.
Cheers,
vma
Hello,
I need help - have tried my best but still can't fix my uni.
The LCD-speaker is not working when case is closed with LCD faceing out.
It does work when LCD is faceing keyboard and uni is not closed (then it switches to Logo-side speaker). I have tested it by rotating screen and the speaker stops to work in very exact moment more-less in the middle of rotation.
As I have looked in manual (http://forum.xda-developers.com/showthread.php?t=349573). The LCD-coaxial cable dosnt have any axis-based connectors there, so basicaly it is just a tighten bunch of wires. So I pressume there is nothing broken as some connector or etc. So as I can think it is not wire-based trouble as the speaker is working when LCD is not rotated (is facing keyboard).
Did anyone met this problem? Maybe some software fix? Any ideas?
Regards,
woocky
I use to have exactly the opposite problem, that is, my external phone (ear) speaker didn't worked after my uni fell, the cure was easy, open the uni, clean the speaker's and the pcb's contacts, gently pull the speakers golden contacts, close the uni, and that's it!
I'm hoping somebody with some knowledge of the HD2's innards can help me...
My vibration stopped working on my HD2. I found the plastic LED flash cover to be 'pushed in' (with the help of a couple xda threads I dug up). Others said it was an easy fix: Open the case and push that piece of plastic back into place.
I opened up the case to correct it. But after putting it back together not only does vibrate not work, but the volume keys, speakers (both earpiece and speakerphone), flash, notification led, and camera all don't work.
I obviously screwed something up, but I have no clue what it could have been. I was very careful. One thing I'll note is that when I pulled the case apart, the plastic volume rocker went flying. When putting the phone back together I got it back into place so that I THOUGHT it should work (it was seated properly and felt "clicky" for up/down movements.
But clearly wasn't just the volume rocker that was affected. It doesn't seem that I pulled anything else loose or anything like that...
But no luck, all that I listed above is non functional, and what I'm left with is a glorified 3.5 in tablet
Any ideas?? Thanks in advance!!!
Snapped a couple quick pics which may help:
http://i50.tinypic.com/mmsa36.jpg
http://i47.tinypic.com/sl1kdx.jpg
Unfortunately when comparing these to other pictures of the inside of the HD2 that I found online, I fail to see any differences, or anything I could have inadvertently screwed up.
Most likely you screwed up(or disconnected from motherboard) somehow your main flexboard, but your picture are not usable for this, you should take off your motherboard+main flexboard from chassis to have a full view!
You probobly just disconnected a small cable. I have no idea of the HD2 innards but did multiple repairs of small stuffs and the flat cables hold in place by a plastic clicker pull out easily - just reopen and check them all, you should be fine.
Thanks for the input! I figured it's something like that, just one small cable. But I didn't even take off the board at all... The pictures show the full extent of the disassembly... Do we still think it's necessary to disassemble it further?
I checked all visible connections, but yeah, maybe I somehow yanked out something that is NOT visible. I'll try to check again today... In the meantime, any more ideas from anyone else? Thanks!
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Have u tried starting up the phone without the backing? I had this issue when I painted my housing the led cover was stopping the motor from spinning but if i took out the backing it works. So I just trimmed the led cover and now it works.
Mister B said:
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Click to expand...
Click to collapse
I'm nooby with regard to this stuff; I only attempted the repair since I read in a couple other threads about multiple self-proclaimed non-super-tech savvy people were able to open it up and move the plastic LED cover for an easy fix.
So what exactly am I looking for with regard to the main-flex? Where is it? I thought I wouldn't really see that unless I removed the board which I haven't done... is it still possible I knocked it loose or damaged it? I didn't think that would be possible since I ONLY removed the back cover (though it does take a slightly uncomfortable amount of force to do so, so I guess anything can happen...).
If not the main flex cable, is there anything else specific to look at which may be disconnected? It seems to be all the stuff at the top of the phone that fails to work (camera, speakers, vibration, flash, volume keys). While the stuff on the bottom (other hardware buttons, charging jack, headphone jack, etc).
THanks!
I have given up. After being stumped briefly how to hard reset the device without the volume keys working (I have Android installed), I was able to do it via ADB from the Android dev kit.
To ebay I go...
Hello,
Where can I find a good replacement for HD2 digitizer?
I have Windows Phone 7.8 on it (I had the same problem on Android) and sometimes when I am using it, the digitizer registers my touches wrong.
Seems to be the left side is most affected by this - Like when I press e, it presses q also, or w then q too. Also happens with s (a) and symbols. Cannot even pinch to zoom.
This has rendered my HD2 a unpractical phone. It started randomly last summer.
Should I change the digitizer in this case or is there something I can try?
Also, my input jack is messed up - when I have a headphone connected to it and the plug shakes in the slightest - The phone things I want to pause the song or play it. Also activates the voice search which is a freaking PAIN.
Can anyone please help me and tell me what I should do about these issues?
Digitizer & other parts such as assembly tape can be found on eBay.
Dosome homework on digitizers & stripdown guide to save yourself from common problems/mistakes.
Audio plug maybe harder issue to rectify, it can be replaced but requires a good solderer to do good job. You may improve things by cleaning socket & cable plug & trying to improve contact spring arms tension position in socket with a pin or similar.
Mister B said:
Digitizer & other parts such as assembly tape can be found on eBay.
Dosome homework on digitizers & stripdown guide to save yourself from common problems/mistakes.
Audio plug maybe harder issue to rectify, it can be replaced but requires a good solderer to do good job. You may improve things by cleaning socket & cable plug & trying to improve contact spring arms tension position in socket with a pin or similar.
Click to expand...
Click to collapse
But does this issue seem related to digitizer being faulty or just a cable a bit damaged? Sometimes the issue appears and sometimes it doesn't.
Ribbon on digitizer is all one piece & any permanent repair usually is only really achieved by replacement of digitizer.
I have had similar issues of screen presses activating other area on screen & dead zones on digitizer error & also the more common no touch issue, all required digitizer to fix .
Anyone know where to find a replacement jack in the USA??
Sent from my HTC One X using xda app-developers app