Uni hinge: broken? - JASJAR, XDA Exec, MDA Pro General

Hiya guys,
I need your help. Seems that my little brother has twisted my Uni wrongly and although it still works normally, the hinge is strange. It twists 90 degrees flat on Pocket PC mode, but in H/PC ("laptop") mode, the screen stops twisting at ~88 degrees and doesn't get "flat". (The screen stays oblique, like if I didn't twist it until the end.) Is there something I can do?
Thanks for your help.

Related

No LED on answer/hangup buttons on hinge

Hi,
When i first setup my Exec using personal mode, the answer and hangup buttons on the hinge woudl illuminate when a call came in (when the unit is closed like a laptop). Now i am using it in corporate mode, the LED's don't illuminate. They only illuminate when the screen is rotated into PDA mode.
I am assuming this is a reg hack. Does anybody know what it is? or has anybody else got this problem?
Cheers
Paul
They don't illuminate when the device is closed, only when you have the screen open or facing outwards.
hollinshead said:
They don't illuminate when the device is closed, only when you have the screen open or facing outwards.
Click to expand...
Click to collapse
And very annoying it is too - especially when both buttons look so similar when not illuminated. This must be hackable?
This has got to be one of the most annoying features of the exec.
Also i have found that if the device is closed, MSVC does not recognise anything you say when activated via BT.
I have never really played with the device in personal mode as the GUI is bollox so cannot comment on if the buttons light up or not when the device is closed. But what i do know is that when it is closed the screen is switched off as if the device is in standby mode, maybe this has something to do with it.
I try to memorize the position of the green button in relation to how I always hold the phone and feel for it like a Braille board. So far I get it 75% of the time.
is anybody using the 'Personal' install on their exec? can they confirm if the LED's are illuminated or not when the phone rings when it is closed?
Cheers
Paul
Someone who's actually opened the Universal may be able to confirm this, but I suspect that the answer/hang up buttons on the hinge don't actually have LED's. I believe that they simply use the light from the screen's backlight to illuminate. As near as I can tell, they're only on when the screen backlight is on.
If that is the case, then there probably won't be a way to get them to illuminate when the case is closed, unless someone can figure out how to get the backlight to stay on when the case is closed (which would also be a big battery waster)
Brett
Yup, i can confirm this. I've just removed the cover on the top of the hinge. There is one wrapped cable coming out of the base at the right hand side. This then splits off, the main part goes up into the pivot hole, and a thinner wrapped wire brakes away from this and attaches to a small pcb which has the buttons and the LED's mounted on it.
Yes, the buttons are only illuminated when the backlight is on, but the brightness of the buttons remains constant even when the backlight brightness is turned down.
Cheers
Paul
As far as I see it, even if the backlight has to come on that wouldn't be a problem - after all, the phone is waking up in order to ring. I also often open up the screen slightly to see who's calling, then close it and press the answer button - therefore switching on the backlight initially would actually save time!
Maybe somebody knows of a "wake-on-ring" hack :lol:
I've just noticed it with my new Qtek 9000 and I was very worried, because I thought my device is broken.
But now I know this is "normal", but it's very annoying :?
I wish I had this problem! .. since yesterday my JJ seems to have those lights permanently on even when I switch the device off
Guys, I've made a program that will keep the hinge leds on all the time.
Actually this is an accidental discovery for a program I'm working on for this thread:
http://forum.xda-developers.com/viewtopic.php?t=37201&highlight=
Those guys want to be able to use the keys and phone functions with the lid closed.
I'll post more in that thread, but basically closing the lid puts the hardware keys in a special state such that they are not responsive at all until the device is woken internally (eg by an incoming phone call). Actually, can someone confirm that the hinge keys work when a call comes in but the lid is closed. I presume they must, since they don't do anything else!
So, the hinge lights are on when the screen is on. But the screen is switched off when the lid reaches about 10 degrees to closing. But the hinge lights can be kept on nevertheless
Grem: are you using TCPMP or a similar program to play music etc in the background? Anything that tries to keep the phone "on" when the lid is closed will keep the hinge lights on.
V
Hi vijay555
I've actually just done a complete cold re-boot and reflashed to the original i-mate factory ROM to see if that would help, then came here in search of anyone having a similar issue.
It started yesterday, i suspect I've had an internal meltdown somewhere, plugged it into sync, noticed a few minutes later it had randomly done a warm reset and appeared stuck on the blue i-mate screen, picked it up and the sucker was hotter than an AMD without a heatsink! I suspect it's warranty time for this unit
Grem, that's worrying. What were you doing at the time? What brand/operator etc is the phone? It might be worth posting batch numbers or whatever for people that have this kind of problem so we can identify if some are worse then others.
V
It's an i-mate straight from the wholesaler no particular operator. Had it a couple of months, have seen other reports on the forum here which sound perhaps similar in that they've overheated.

broken screen ?!?

hi guys, I have a problem, my screen keeps doing this thing where it stops working, it looks like the device has crashed, but all the buttons work fine. the touch sensors for the screen works about 30% of the time. I've just figured tho that if I twiddle the screen a little it works again. but does it again soon after.
does this sound like it needs to go back to shop for repairs? does it sound broken?
please give your replies.
I have a similar problem with the screen:
- Sometimes (once or twice a day) the Universal does not accept touch screen input.
- Then I twist the screen back and forth.
- After this touch screen works again.
How can avoid this?
BTW, is there a method to physically fix the screen in landscape?
I only use the Universal with the screen oriented in "Laptop" Mode.

Touch screen stopped working :-(((

Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....

Accelerometer problem or is it?

I droped my phone but it was inside a big protective case now i don't know if this issue is related to this but here it goes.
If i open a picture message with the phone in my hand the screen goes into landscape, when i exit out it stays in landscape until i exit the messaging client. Here is the strange part, if i leave my phone flat on the table and do the same it goes back to portrait mode as soon as i close the picture.
Does this sound like the phone has a hardware damage?
Tried restarting it and calibrating the accelerometer, nothing.
Can someone please also do me a favor and see if in the game Teeter when the phone is on the flat surface does the ball still rolls slightly to the left? I can make it stop and not move but it prefers to go to the left.
My ball stays still.
I don't see how this can be a problem since accelerometer works but in an sms client only when the phone is on the desk.

LG G2 -- Screen brightness can't exceed 40%

Hello.
The other day my phone suffered a little water damage. Not submerged in water or anything, but a couple drops found their way into the phone. The phone was turning off/on and functioning, but the display was black. I could feel buttons being pressed and stuff...the screen just wasn't illuminated. Well, I left it alone for a while, and now the screen works to a degree.
It's functioning perfectly, except it can't go above 40% brightness or the phone's screen goes black. As soon as I move the slider at or below 40%, the screen works perfectly again.
Obviously whatever illuminates the screen is damaged to some degree. The same thing happens when using apps like Lux...so I'm pretty sure it's a hardware problem now. I'm wondering if anyone has any idea what exactly could be damaged so I can fix it myself, or have anything to try before taking it apart again.
Thanks!
macdaddyusmc said:
Hello.
The other day my phone suffered a little water damage. Not submerged in water or anything, but a couple drops found their way into the phone. The phone was turning off/on and functioning, but the display was black. I could feel buttons being pressed and stuff...the screen just wasn't illuminated. Well, I left it alone for a while, and now the screen works to a degree.
It's functioning perfectly, except it can't go above 40% brightness or the phone's screen goes black. As soon as I move the slider at or below 40%, the screen works perfectly again.
Obviously whatever illuminates the screen is damaged to some degree. The same thing happens when using apps like Lux...so I'm pretty sure it's a hardware problem now. I'm wondering if anyone has any idea what exactly could be damaged so I can fix it myself, or have anything to try before taking it apart again.
Thanks!
Click to expand...
Click to collapse
Did You ever get to the bottom of this?
Having the same exact problem?

Categories

Resources