Anyone have a solution for this? I have my Wizard go to standby after a short time and always make sure it is in standby when I put in in my case. However, when I receive a call and pull it out of the case, I almost always press one of the buttons. So when I answer the phone I have the camera going, contacts open or the connection manager open. I use all the buttons so I don't want to disable them completly. I wash there was a way to disable all buttons except the answer button for like 5 seconds after a call starts ringing. Or, be able to set buttons to not activate unless pressed for 2 seconds or so. Or, require 2 presses to activate. Anyone have any ideas?
Thanks
Turn on the password (4 digit one is fine) and set to 0 minutes, the phone will "lock" as soon as you go into standby but when it rings you will be able to answer with the red/green buttons but nothing else until you put in your password.
Thanks, I will give that a try. I used a password before but it slowed things down so much that I removed it. I have done quite a bit of optimizing since then and will try it once more.
it does slow the use, and gets annoying (i still use it) but it does work until i find a decent app to do it. All it really needs is 2 touches or 2 buttons to unlock but not found anything yet... \
I have solved this with litle less work .I have Device lock Bar on the top, under date , so you need twice down and middle buton to lock the
device.
device lock doesn't seem to play well with the password application. if you have password activated you can do a device lock but when you put your device on standby and bring it to full power it is unlocked. if you use device lock without password it works.
any solution to lock keyboard during a call ? i always active some functions with my ears(...) when i speak
starseb - switch your phone to stand-by mode... the radio (phone part) should remain on, and you can continue calling. Then just switch it back on when done ( or not %) )
sorry for my english, but i make i make a mistake. i would say how to lock screen during a call.
bostjan said:
I have solved this with litle less work .I have Device lock Bar on the top, under date , so you need twice down and middle buton to lock the
device.
Click to expand...
Click to collapse
Is there a good way to unlock by pressing just keys?
Try christoph's deltaLock map it to a hw button then set it to be unlocked by the same hw button.
ok so I just got a new TyTN to replace my Excalibur so how do I lock the keys so when it's in my holster nothing goes off??
The excalibur I just had to hold the end key but this doesnt lock that way..
help
you can set an auto-security lock; locking after 1, 3, 5, 60 minutes etc.-Note this is a password/pin protected lock
Alternatively you can perform a device lock; under settings>today> make sure device lock is enabled, now you can click on this on the today screen to lock your device, I think you may also be able to assign this to a key but I'm not sure
I mostly use (3rd party program) slide2unlock; you literally slide the on-screen slider to unlock, this activates automatically when the device sleeps or goes into standby
Its free and widely available
Hi,
Phone Lock on my HD2 is set to ask for password if phone is unused for 15 minutes. But my HD2 ask for Phone Lock password each time the screen goes off. Is it possible to change this behavior?
I have the same problem. The phone lock is set to 24 hours, but if the dispaly goes off and i power it on the hd ask for the phone lock password, too.
Can someone help?
Usually if I don't want the phone to lock, I just set the screen not to turn off at all. Under settings, display etc.
HI,
i want, that the screen is locked but only with the slider. At the moment i slide to unlick and then i have to enter the phone lock passwort. But this password should only appear if i restart my HD2 (for this reason i set the phone lock password option to 24 hours).
with my "old" HD this works great.
Download this cab file to your device > run > switch off > switch on
http://forum.xda-developers.com/attachment.php?attachmentid=246722&d=1258236796
Strange, does this fix work for everyone else?
After I installed it, once I press the power button to shut the screen off, when I press any of the hardware buttons, it dumps me to the screen that I was on, but no longer asking me to swipe. I guess I'm looking for the fix so that the below behavior happens:
1) If I press any of the buttons before my "timeout" happens, phone should ask me to swipe my finger to "unlock" the screen.
2) If I press any of the button after the "timeout", then phone should ask me to swipe but then also ask me to punch in a PIN or complex passwd, depending on the setting.
Are there any registry hacks that can do what I described? or does it do exactly that and it's my particular phone that isn't working?
thanks!
m1k1 said:
Download this cab file to your device > run > switch off > switch on
http://forum.xda-developers.com/attachment.php?attachmentid=246722&d=1258236796
Click to expand...
Click to collapse
Having been interested in exactly the same thing, it seems like this cannot be done at present. The lock is either there with a password or not there at all. My current compromise is to set a one digit pin, but that's a bit pointless really.
The slider can be added with S2U2 but this seems to defeat the object somewhat...
I have the same problem. I'd like to be able to lock the device (or at least to turn off the screen) without typing the password at each unlock. I set it to 24 hours.
The patch should be fine as temporary solution
Password lockout problem solved
Great,
this has solved my problem that intermittently and usually overnight I get 'incorrect password message' when I try to unlock, only solved by a soft reset which is rather worrying.
I don't want to have autolock, especially every time I switch on and off like you all.
This little add on allows manual lock (by setting widget on screen with SPB mobile shell), and I have set default to 12 hrs for password screen.
Many thanks
Rory
RoryC said:
my problem that intermittently and usually overnight I get 'incorrect password message' when I try to unlock, only solved by a soft reset which is rather worrying.
Click to expand...
Click to collapse
Ha! Think that's worrying? ...You're right.
I had this a few times in the past and each time was able to solve it by a soft reset.
Not the last time, though. After trying numerous soft-resets, I finally saw no other way out than to hard-reset my device. In the end, it didn't even display the "incorrect password" dialog anymore. I suspect I had entered an "incorrect" password too many times, but the device did not manage to present me with the "enter a1b2c3" prompt that it usually does when that happens.
Very, very frustrating. Some quick googling gives a few reports of this happening to other people, not just on HTC handsets either. Not too many though, so it sounds like it's pretty rare.
(For the record, running 1.48 WWE here, had a 7-digit simple PIN set as the device lock password, with Windows Default display)
i have the same problem it asks for password every time i unlock the phone and the bad thing is that sometimes even correct password doesnt seem to work so that i have to soft reset or wait for half an hour b4 trying the password again , just confused about it . australia
i took out my password for now. i have to reset once in 2 days now to unlock phone. i wont be able to make a call in case of an emergency so better option take it out.
mobilebuddha said:
Strange, does this fix work for everyone else?
After I installed it, once I press the power button to shut the screen off, when I press any of the hardware buttons, it dumps me to the screen that I was on, but no longer asking me to swipe. I guess I'm looking for the fix so that the below behavior happens:
1) If I press any of the buttons before my "timeout" happens, phone should ask me to swipe my finger to "unlock" the screen.
2) If I press any of the button after the "timeout", then phone should ask me to swipe but then also ask me to punch in a PIN or complex passwd, depending on the setting.
Are there any registry hacks that can do what I described? or does it do exactly that and it's my particular phone that isn't working?
thanks!
Click to expand...
Click to collapse
Is there any fix for this problem yet?
with S2U2 you can set up a password config. (require password every: 5mins/15mins/1hr/ 4hrs or 12 hrs) S2U2 seems to eat my battery up though, thats the downside. also you have to download the "disable autolock" cab for it to work from the tweaks an mods sticky in themes/ apps forum. its a shame about the battery drain as this app is awesome but definately worth a look.
sorry heres linkhttp://s2u2.ac-s2.com/
Same problem and no answer until now ?
I also have the problem that I cannot configure my HTC HD2 that the screenlock works without PIN. I like to start the secure lock only after a certain time i.E, but there is only the way everytime with PIN or at anytime with PIN.
Sometimes mostly overnight the device "forgets" the correct PIN and I have to make a softreset. After done this , I can enter the oriinal PIN.
Is there no solution until now ?
Is there any idea what to do.
Read tip 27 of the Sticky Tips and Tricks - http://forum.xda-developers.com/showthread.php?t=583638 - then the PIN will only be required after the timeout, not every time you lock the screen.
The bit where it doesn't accept the password is a known bug reported elsewhere, but there's no fix yet; I wish there was, because I get it occasionally.
Resolve screen lock issue by editing registry
Enable/Disable the Exchange security policy – HKLM\Security\Policies\00001023: 0 = Enabled; 1 = Disabled
Inactivity time
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\AEFrequencyType: 0 = No inactivity time; 1 = Activity time enable
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\AEFrequencyValue: number of minutes before timeout
thesedays74 said:
Enable/Disable the Exchange security policy – HKLM\Security\Policies\00001023: 0 = Enabled; 1 = Disabled
Click to expand...
Click to collapse
Until the buggers push it out again and you get fed up of having to set a PIN then edit the registry every day
Incidentally, is there a way to lock the screen without a PIN after a set period of time? All I can find is either a manual lock or a lock with a PIN.
Slidelock & pin code every time driving me nuts!
thesedays74 said:
Enable/Disable the Exchange security policy – HKLM\Security\Policies\00001023: 0 = Enabled; 1 = Disabled
Inactivity time
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\AEFrequencyType: 0 = No inactivity time; 1 = Activity time enable
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\AEFrequencyValue: number of minutes before timeout
Click to expand...
Click to collapse
I made these exact reg edits (my very first registry edit!) and it's made no difference at all, my HD2 still asks for pin every time I switch off & on.
I want to keep the slide lock to prevent accidental button presses when device is in my pocket, but the pin input is a pain my previous device only asked for it once every 24 hours or after powering up the phone. Has anyone solved this yet?
Should I change the registry back to pre-edited?
Disable hardware buttons
I realized one thing that is draining my battery is the accidental press on hardware buttons when my hD2 is in my pocket. Is there a way to disable the hardware buttons other than the end/power button when the screen is turned off ? It is silly that the press of any hardware button turn on the screen ...
I installed this rom recently and noticed it was heating up in my pocket. When I looked, the screen was unlocked. I checked why this was happening and by accident, the knockon was activated. I disabled this function and the problem persists. Does anyone know how to solve it?
Obs.: The problem is not warming, but the unlocking of the screen because it has times that it makes calls to some contacts, opens randomly and opens some applications ... causing the device to warm up ...
If you're using Auto Face Unlock along with Smart Lock's On-body detection the phone will sometimes unlock right after you hit the power button without locking, that might be it.
ali6944 said:
If you're using Auto Face Unlock along with Smart Lock's On-body detection the phone will sometimes unlock right after you hit the power button without locking, that might be it.
Click to expand...
Click to collapse
Hello, I do not use Auto Face Unlock. That's why I find it strange. I have to use a password or the unlock pattern so that no bull**** happens.
Is there a way to bypass the lock screen when using smart lock when trusted? What I want to do is double top on the AOD screen which then takes me directly to the home screen and NOT the lock screen where I have to swipe in again. Any ideas?
I have also been looking for a solution to this. While I have not been able to completely bypass the lock screen here is a workaround which minimizes when the lock screen appears.
Settings --> Lock screen --> Secure lock settings --> Lock automatically I increased the time from 5 seconds to 30 Minutes (which is the maximum value)
When away from my trusted places I use the power button which locks my phone immediately based on the 'Lock instantly with power key' setting
Hope this helps
I used Gravity Screen for this purpose a few years ago. I don't know if it works with this phone but you can try it out.
I also is able to turn on your screen as soon as you pick it up. And bypass your lockscreen ofc.