Hi!
I'm thinking about using my M1000 with my company's Sim.
Problem is that to dial personal numbers I would need to add "46" before the number I am dialing (this is for cost control... the company pays for phone call of collegues and clients, I pay for my personal ones).
Now, I am afraid that due to this restriction I would not be able to tap a personal contact number and have it dialed and also that I would need to delete the whole number from the phone display in order to add the 46 at the beginning.
Is there any application that would allow me to easily add the 46 in front of personal numbers before they get dialed?
THANKS!!!
Chris
Are you saying that you can't simply add the "46" to your personal phone numbers in your Contacts list? I just added "46" in front of a number in my contacts list and dialed it. It did not work on my network, but it did dial it.
I could but...
I could add the 46 in front but...
0) do it for all of my contacts its a long work...
1) It would be difficoult to revert should I change sim
2) I would get all my contact screwed if I try for example to dial from my PC or share them with someone
3) I don't need the "46" for SMS... so if I put it for SMS they would not go...
4) Incoming calls would not be recognized becouse the caller Id could not match the caller with the 46...
So it would be best if I could just add the "46" with a botton to the end of a number I would like to dial, just before I dial it...
Thanks anyway!
Chris
Did somebody know how to disable functionality in Phone mode that is sending Your Phone number ID, to the call receiver?....or in other words...is it possible make anonimous phone calls?..
tnx
There are 2 ways. Ask your provider to permanently switch off caller id or go to Start - Settings - Personal - Phone - Services - Caller ID - Get Settings - No one
omino_ribelle said:
Did somebody know how to disable functionality in Phone mode that is sending Your Phone number ID, to the call receiver?....or in other words...is it possible make anonimous phone calls?..
tnx
Click to expand...
Click to collapse
Of course, you realize that the Cell Phone company still knows you made the call, and whom you called? So it is anonymous only to the receiving party, not in any permanent sense.
Yeah, we should fix that too ! No more bills (Big OR small) :lol:
should be interesting in fact....aha....thanks to ZERIMAR... i was able to redefine the settings avoiding to send ID nr. to my frends......
Didn't the GSM network have anoption never to show Call-ID, unless you put some code in front of the tel.number ?
Or was it the other way around ?
Instead of permanently disable Call ID forwarding through Phone->Settings as suggested, in Italy we have also a code you can put before the number you're calling that disable the ID just for that call. The code is *06#. Maybe other countries are using the same code too, don't know.
Isidoro
Yea it is but if i want t permanently hidden , i should redefine all numbers in phone memory adding this code in front...and then if somebody is calling me, ID is not going to be linked to the number in phone memory......better set up everything in the the phone functions directly....
Hi folks,
TIM Brasil send me ans SMS with all calls I've lost. useful when I flying, at arrival I saw who call me.
The problem is the SMS contain the caller number, time and date, so I need to search at Contacts to discover the caller name.
Someone know a piece of software able to look at phone number inside of SMS and scan the Contact to match it, showing the name of the contact?
Best regards
Any ideas?
Here in Italy vodafone sends a similar SMS but sets the sender name to the one who attemped to phone you
In this way the phone shows automatically the name (if it has been stored in contacts)
To quickly discover who's the owner you can do two things:
1) if the message contains "This number +xxyyyyyy tried to call you..." press the down key (the number should be selected by a square box) click and your phone should start dialling that number (doing a lookup in contacts and showing the name)
2) you can remember the first numbers (excluding the international prefix) press "red phone", "green phone" (to quickly start the phone application) and use the hermes' smartdialer to quick find who's the owner.
Try using SPB Diary...
Make sure your numbers are in the international format.
LinoX said:
Here in Italy vodafone sends a similar SMS but sets the sender name to the one who attemped to phone you
In this way the phone shows automatically the name (if it has been stored in contacts)
To quickly discover who's the owner you can do two things:
1) if the message contains "This number +xxyyyyyy tried to call you..." press the down key (the number should be selected by a square box) click and your phone should start dialling that number (doing a lookup in contacts and showing the name)
2) you can remember the first numbers (excluding the international prefix) press "red phone", "green phone" (to quickly start the phone application) and use the hermes' smartdialer to quick find who's the owner.
Click to expand...
Click to collapse
In fact this work, but is not exactly what I want, because after a airplane trip the SMS has 3 or 4 numbers. So I need to call/abort 3 for times... It's not elegant way.
thanks.
madhero said:
Try using SPB Diary...
Click to expand...
Click to collapse
What is SPB Diary???
spb diary is a diary application in form of today plugin..
but as far as I know it can't do what you're looking for.
WM developer
Hi Guys,
I'm trying again... Is there a WM developer here who could develop a little plug in to do it?
I think is not complicated, but I don't know WM development to do it.
Of course this could sold to the community.
i had once a siemens sl45 and when i had a phone number in a sms it replaced it by the name in the phonebook... i so miss that feature..... i haven't seen it on other phones since then...
I'm not alone
Finally someone understood what I'm saying.
It's very useful this feature. I'm wondering if someone could develop this.
Anybody as a volunteer?
Maybe this is what you need?
http://www.saman-cz.com/ppc/index.html?drfovrw.html
Its work - It's great
Thanks Moe,
It's exactly what I was looking for.
Thank you.
In my old Hermes (Cingular 8525), there is an option in the Phone Settings to hide my caller ID, so that when I call someone they will not see my number on their phone.
However, with my Mogul, I don't see that option. Does anyone know how can I do this?
I miss this feature on the mogul too. But you can type *67 and the number for example the number is 18001234567 type *6718001234567
P.S. if you find a patch to do this from a menu I would love to hear about it.
Thanks for the info. But that means I can't use my "Phonebook" to dial, as I have to manually enter *67 and then the number.
Maybe some of our resident hacker can figure it out?
Do you just want to permanently hide your number from everyone you call? If so, you should be able to ask your carrier to add a "No Caller Id" code to your account...
you could edit the phonebook entry or make an aditional one that is blocked and call it their "other" number or fax or something
Hi all,
Thanks for the suggestions. I don't want to permanently block my caller ID, only for select number. I prefer to be able to change the caller ID feature on the fly without editing the phonebook, but I guess I'll have to do so until Sprint implement this feature.
Hi
I'm with Bell Canada and we have a option on their web to block caller ID. I selected this option and in my contacts I added *83 to the number I want to unblock my ID. So if I dial a new number I know that my block caller ID is on.
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me