I was wondering firstly if there was a way to turn off the annoying "battery low" messages which appear when the battery is under 20%.
Also, is there a way to use the SD and WLAN features when the battery is below 10% - perhaps a reg fix of some sort, as currently it doesnt allow me to use these features when the battery is below 10% which can be very inconvenient!
Thanks[/i]
When the battery of my TyTN gets at 20%, I start getting system notifications warning me about a low level battery and others telling me to charge the battery like the manual says so.
The issue is that at 20% the TyTN still has a lot of life time, and meanwhile until the battery gets completely drained, I get MANY of these notifications that keep disturbing, it really isn't handy.
Does anyone know any solution for this? Maybe some way to start this notification only at 10% and maybe making them fewer.
It's only needed one or two notifications to remember us we are getting low on battery power, no need to keep reminding it all the time...
Thank you.
It's anoying me aswell...
I hope they fix this in the new ROM.
On the same general topic, anyone else find the battery status to be inaccurate?
I've re-enabled the small, four-bar battery indicator at the bottom of the home screen with a hack from MoDaCo.
Thing is, it's full most of the time - then wack! it goes to one-bar red and I start getting notifications. It doesn't seem very dependable. Anyone else get this?
Marques said:
It's only needed one or two notifications to remember us we are getting low on battery power, no need to keep reminding it all the time...
Click to expand...
Click to collapse
same problem with me. looks like there is some serious bug with low level battery notification. in my case, i have Magic Button installed and i'm using its feature, which shows thin battery bar at top 2 pixels of screen (something like Batti). each time when i wake up my Vario II, this indicator always shows 100% battery for 2-3 seconds, after which it refreshes back to current state.
so this thing brings the idea, that these multiple notifications are caused because device 'thinks' that battery is full after each wake up, but after few seconds it turns out that it isn't, so system is generating notification - again and again after each wake up.
I've been having similar issues except in my case the battery is actually full.
The device powers up after being in 'sleep' mode (or sometimes during normal usage) and generates low battery notifications, even though the battery has been on charge all night and is actually full or at nearly full charge.
A soft re-set doesn't seem to help but physically switching the device off and on again seems to fix the problem (the battery showing 100% afterwards) but theres a definate bug with the power monitoring software
I really want to know how to modify registry of Hermes to avoid low battery notification too
Just a thought, on other devices such as the universal and breeze etc... (i see ive mentioned smartphones aswell as ppc) ... is the battery indicator shown in 10% blocks like the hermes or are they in steps of 1%?????
Anyone know of a reg hack or possibility that this will be changeable to 1% steps???????? (ROM change or the like?)
Ah yes, pretty irritating, guess we'll have to wait for the rom updates?
mrvanx said:
Anyone know of a reg hack or possibility that this will be changeable to 1% steps???????? (ROM change or the like?)
Click to expand...
Click to collapse
There is still no way to change the battery monitor to 1% steps.
From what I've checked, there is still no fix for this massive flood of low battery notifications. If anyone have any other idea... please share it.
My WM6 ROM show low battery warning at 40% - really annoying. I really just want to get of these notifications altogether!!
One possible cause of the battery showing that it is full only to have it drop 50-80% after a few minutes is that you are using a trickle-charger such as the USB cable to charge it.
When charging with one of these devices, when the battery says it's fully charged it usually isn't. You will want to take it off of the charger for a minute or two after it says it is full and then put the charger back on if you want to get a consistent full charge with a trickle charger.
Any news about the annoying low battery notifications?
I hate it and I would like to kill it forever...
Thanks
SaRo
In s-k software's sktools there an option to allow it to show the low battery notification in the sounds and notifications. I find this very useful as i disable the message on the screen which gets in the way when it pops up to tell you battery is low. You can even change the sound or just disable the notification completely! Theres got to be a reg setting for it so people can use this little hack without buying the program.
I have recently purchased a Mugen 3000 mA battery. I am thrilled with the extended battery life after fully charging and discharging it three times as recommended by the manufacturer. What I find annoying is that WM6 no longer gives accurate information regarding remaining battery strength. If I run the battery down to 2%, remove the battery and restart WM6 says 37%. At 2% I can repeat and WM6 still says 37%. After running down to 2% a third time and repeating WM6 says around 10%. After that it varies a bit but you get the picture.
What I would like to know is if one of you geniuses out there has discovered a registry edit, hack or 3rd party software that will provide accurate battery info so I don't have to be distracted by having my battery say 2% for hours on end or repeatedly remove and restart.
BTW, BatteryStatus Ver. 1.04.200 beta2 build 0173 reports the same incorrect info and so does SPB Mobile Shell 1.5 Home Tab.
Thanks in advance for your informed guidance. OK, that is laying it on a bit thick but I always highly recommend this site to anyone I know interested in really learning how to take full advantage of that little computer in their pocket.
Take a search on XDA for Ariel monitor maybe it solves your problem.
Thanks for the suggestion. It is a nice little program but it suffers from the same problem. I suspect I need to find a way to change the mA capacity WM6 bases it's battery calculations. I don't know if that can be done with a registry edit or if there is a third party battery monitor that has an option to change the battery capacity for calculation of percentage remaining or better yet auto detects the actual battery capacity. Ideally it would be able to both accurately read remaining percentage and make reasonably accurate time remaining estimates based on current and historical battery drain data.
It is like driving a car with a broken gas gage. Sure, you can use the odometer to estimate how much gas you have left but you are always worried your estimate is off and you will be left stranded without a phone ... oops crossed metaphors.
How do the rest of the users with extended batteries handle this irritating situation?
Bump. I can't believe i'm the only one with this problem.
I know this problem also i will wait with buying a high capacy battery until i find such a hack
The Kaiser uses a smartbattery. The battery capacity is based on the information that a small processor inside the battery tells the phone's main processor. There are several things that could be the problem:
1. The small processor in the 3rd party battery is programmed with the old specs for the standard battery. The is nothing you could do about this.
2. The small processor needs to be calibrated. You would do this as follows; set your phone to never turn off no matter how low the battery got. Now, run the phone down until the thing dies from lack of power. Then charge it all the way up. This should fix that issue. I don't recomend doing it many times, because it is not good for Lion batteries to be fully discharged too often.
This is a very valid issue which I have faced many times when using a 3rd party extended battery with other phones.
Not sure how to solve it though, although I have the 3000mah on order myself.
I think the battery reading is given by the battery itself, and most of these 3rd party manufacturers don't really care to put a smart processor in the battery (to reduce costs/make it smaller/etc).
I have the exact same issue and although it is a nuisance, I have found a workaround to keep using the phone. Simply physically removing the battery and replacing it will increase your remaining battery power substantially. I normally wait till the first low battery reminder to do this. Also, how do I set the phone to never turn off no matter how low the battery gets? This would also be fine with me.
utbiglall said:
I have the exact same issue and although it is a nuisance, I have found a workaround to keep using the phone. Simply physically removing the battery and replacing it will increase your remaining battery power substantially. I normally wait till the first low battery reminder to do this. Also, how do I set the phone to never turn off no matter how low the battery gets? This would also be fine with me.
Click to expand...
Click to collapse
I didn't run into this issue until I reflashed my ROM to one with W6.1. Then, rather than get 12-13 hrs with my 3amp battery, I'd get 6. I used my original battery, but when I put the 3amp back in, I still had 47% left.
It's the ROM, and until there's a fix, it would be a pain to pull and replace the battery just to work around. I've done this several times recently when I'm on battery power, but I'd rather not.
Anybody heard of any other fixes, outside monitor, or do we wait until we get a Windows Mobile 6.1 fix?
Still no luck?
Hello,
Has anyone been able to find a solution for this. I am ordering the extended battery today. I will try to fully discharge it and then recharge it as was suggested and report back.
I emailed Mugen. We went back and forth with them trying to troubleshoot whether it's the battery or OS. They were clueless, but did offer an RMA to replace the battery. I pay the postage. Not sure if I'll send it back if it's the OS. I pull and replace the battery right now. It's a real pain, and I hate opening the case so much, but it's the only way I can get an accurate read.
PhoenixAG said:
This is a very valid issue which I have faced many times when using a 3rd party extended battery with other phones.
Not sure how to solve it though, although I have the 3000mah on order myself.
I think the battery reading is given by the battery itself, and most of these 3rd party manufacturers don't really care to put a smart processor in the battery (to reduce costs/make it smaller/etc).
Click to expand...
Click to collapse
The processor is required for these types of lithium ion batteries because it regulates the charging of the battery. If it didn't the battery would not charge properly, or maybe not even charge at all.
There is no solution for now, people from other forums tries to patch battdrvr.dll.
But two things may help a little:
1.You may completely disable battery monitoring
HKLM\Drivers\BuiltIn\Battery rename or remove string battdrvr.dll
But you lost monitoring completely.
2. change HKLM\Drivers\BuiltIn\Battery\Order change value from 15 (in my case) to 0. - After this battery lasts longer until power off.
There is not complete hardware or software solution for this problem. We need to wait.
Low Battery warning:
By default, a PPC will sound a warning sound when the battery is running low (10%, fixed value), but there's no way to disable or change the notification. To enable this, so that it is visible in the "Sounds & Notifications" control panel, set:
HKCU\ControlPanel\Notifications\{A877D663-239C-47a7-9304-0D347F580408}\Default = "Low battery warning" (REGSZ string, no quotes)
Anybody have any updates on this? I have noticed this more on WM6.1, but it was still an issue on WM6. I just find this so annoying!
Is there any radio that can fix this? I noiced that this battery reading issue only occurs when the Phone Signal is on. When off, it never happens to me. Or it seems. So it has something to do with the radio.
bump, anyone got a solution?
this is very interesting, i bought the seidio 3200 battery i am having the same problems. i just tired the
change HKLM\Drivers\BuiltIn\Battery\Order change value from 15 (in my case) to 0
i am going to see how that works out throughout the day
Tried It
I am having same issue, reset the registry key to "0" and ran for a full day, no change, still incorrect reading. I have a 2700 Mah battery and the charge indicater is completely wrong on it. I have cycled the battery as per reccoemndations, but still get wrong power remaining readings. Can remove the battery and resets itselft to a more correct reading.
I am out of ideas, guess we need someone from HTC to chime in with a hardware fix.
MWS
ms0529 said:
I am having same issue, reset the registry key to "0" and ran for a full day, no change, still incorrect reading. I have a 2700 Mah battery and the charge indicater is completely wrong on it. I have cycled the battery as per reccoemndations, but still get wrong power remaining readings. Can remove the battery and resets itselft to a more correct reading.
I am out of ideas, guess we need someone from HTC to chime in with a hardware fix.
MWS
Click to expand...
Click to collapse
i have tried it too and it still does the same thing. i would still need to pull the battery and restart the device for the batt meter to get a more accurate reading. i could do it about 3 times before the battery dies completely.
is there this problem with all extended batteries or just with the larger ones?
the reason I ask is that I've got a $17 credit at Amazon and was thinking of grabbing a 1600mah battery, it's only like $22 with ship so I'll only pay a few bucks for it really...
I wanted to get the larger one but it's fat and won't fit standard carrying case, but the 1600 is slim and will fit in place a regular battery
Anyone know of a status bar Battery Icon that also shows drain in either mA or mW?
If not, perhaps someone around here might be interested in creating one as I have looked but cannot find one. (I do not mean a Today Plugin like HomeScreenPlusPlus/BatterStatus)
The idea:
Essentially similar to the WM Battery Icon that is there now with bars showing charge but with added feature of numerals showing mA drain. These numeral could either be overlayed on the icon or squeezed beneath it in tiny font.
The advantage of this arrangement is:
1) it would work with TF3D on a Diamond. This is because it would not be a today plugin. Simpy an alternative to the current battery icon on the Status bar.
2) Would enable user to always see charge remaining and current load.
I like the idea of always being able to see the load on my battery as often I have apps running in the background which are chewing through the battery. Conversely if the mA drain is low I know these apps cannot be running and all is good. Makes for an easy way to increase battery life.
Essentially all the app would have to do is somehow ascertain current drain in mA and display it over the battery bars on the icon. Nothing more. Be great if one of you clever programs could put this together. I reckon it would be popular.
Would any one else be interested in a replacement for the default status bar battery icon that worked like this?
Battery Status is ur best bet
Hello friends.
I've encountered a nerve wrecking problem.I've been searching the forum for a solution but everything I have found does not suggest one.
My problem is that my battery percentage is not showing the correct number.I have my original stock rom 1.14.401.3 (22273)and my radio is 1.09.25.14.I have SPB Mobile Shell,S2U2 and Spike's taskbar.
What I do is fully charge my battery overnight o 100%.During the day and using it (calls,GPS) it would go down normally to about 65%.
The thing is that if I don't use it after wards it would go down normally.I then do a soft reset and I find it at 2% (!!!!!)
I charge it and it goes up to 43% at which I unplug it and do another reset.It shows 32%......I do a 3rd reset and it shows 43% again.
Apart from a hard reset can anyone give me a clue as where to begin?Could it be a faulty battery?
I try some solutions like exiting SPB Mobile Shell and S2U2 but I have the same problem even with Touch Flo...
Any help would be more than welcome.
Thank you
Chris