I had a problem with some keys on the keyboard not responding.
But I also have another problem, after assembling the phone back, I tried fitting the card in, and it didn't make the click sound, now somehow I'm not able to have the card inside the storage card compartment.
Is there any switch, was this done, because of the 3 sheets of paper?
DarkWolfx said:
I had a problem with some keys on the keyboard not responding.
But I also have another problem, after assembling the phone back, I tried fitting the card in, and it didn't make the click sound, now somehow I'm not able to have the card inside the storage card compartment.
Is there any switch, was this done, because of the 3 sheets of paper?
Click to expand...
Click to collapse
Depends where you put the paper.
Whatever, you're going to need to dismantle again. Either the slot and it's spring mechanism are damaged or (perhaps more likely, something is pressing on it/obstructing it.
I'd say dismantle and test it when you have it apart and keep a close eye on whether anyting is interferring with it as you re-assemble.
Mike
Yes Mike, I have it disassembled, I see nothing obstructing the storage card compartment, I checked on top and bottom of it, the 3 pieces of papers should not be obstructing them in any way.
I think the spring mechanism is damaged, how can I determine that, and how can I try to fix it?
When I push the card, on the left side I see something trying to move out, and from the top of it, I see the white mechanism inside pushing in, and it did feel the spring mechanism, but it didn't click, so in someplace it should click, thought I'm not able to find where.
it does go completely in, and feels like springing, but not clicking.
DarkWolfx said:
Yes Mike, I have it disassembled, I see nothing obstructing the storage card compartment, I checked on top and bottom of it, the 3 pieces of papers should not be obstructing them in any way.
I think the spring mechanism is damaged, how can I determine that, and how can I try to fix it?
When I push the card, on the left side I see something trying to move out, and from the top of it, I see the white mechanism inside pushing in.
Click to expand...
Click to collapse
I'd need to do a close inspection of that. Unfortunately that's unlikely until the weekend. However, even then I wouldn't be too hopeful of being able to give very practical help, if only because describing anything that small would be difficult enough let alone how to fix it.
Still, I'd be willing to have a look at mine if you still have the problem by then.
Mike
*Update*
As trying multiple times, to see if it made click with anything, the storage card is not even being recognized by the device anymore...
So now..it's basically useless to have the storage card compartment, lock the card.
Don't know why... or the reason..but I'm starting to lose faith in these HTC devices as a first timer...
But anyways, as posted on the other thread, I have an old HTC hermes, that I replaced the motherboard with.
That storage card part, works fine, it does click. But...the real question will be, how exactly can I transfer the old storage card into my own device?
Or maybe if I make work the old motherboard?
Mike: You said on some other thread, that you might think that a fuse is blown right?
I saw an image showing this, but the fuse is under the metal plate, how can I get under it, and check if the fuse is blown indeed or not?
Related
Anyone know why ??? It just wont click in anymore... I woke up one day and it was just sticking out - Ive tried jamming it in but its just not reading it!!
Anyone have any problems like this before ? All my stuff os on the card :'(
Only replying so you dont feel alone. But 1st off check if anyone broke inside it, Anything stuck? I could suggest opening it if you have the tools to check it out and maybe fix it if its not latching right.
Also you can still get a adapter at radioshack for the mini sd. I did. It was 20$ came with SD, Mini SD and Micro SD all in one. So least you could get your stuff. =)
Mem Card
Does it work if you hold it in? If so, I didn't like that mine came out occasionally so I hot glued it in. Hold it in, run a small bead of hot glue on top wait a sec and press the glue into place with your thumb. The glue wont run into the phone and it's easy enough to remove when you actually want it out. If your careful you can even heat it a little with a hair dryer to smooth out the glue. Personally, I don't ever take mine out. I had problems with the device not recognizing my files after removal. I install most everything to the SD that works right there.
**Try this at your own risk. I've done it several times and never had a problem. Just don't blame me if you break something.**
You can apply a thin layer of sticking tape around it to keep it firmly in the slot,but make sure you don't cover the connections with it.It'll stick in there and work proper.
Cheers
It just doesnt seem to be reading it at all - But when I plugged in into my wii all the music is still on it and it seems to be working fine.
When I try and jam in my old card it flashing for a second to say would you like to format the card so it must be working kinda... Argh!
Its really annoying - I used it as an mp3 player quite a lot and theres just not enough internal space...
Hopefully it will fix itself soon as that appears to be the only hope
I'm wondering if maybe the mech is loose and pushed inside. May take a little surgery. If I remember right there is some sort of spring loaded mech that keeps pressure on the card connections while in the slot.
Today I removed my minisd card and put it back in shortly after, but something went horribly wrong
Somehow I broke the thing that holds the card in position so now it wont stick in.. so I tried to make it stuck in with a paper which works but it doesn't get recognized then, I guess the mechanism which holds the card always turns on a switch thats tells my wizard to start reading the card
Does anyone got any idea to fix it, cause this sux big time (I bought the phone a few months ago for €200), I cant find my receipt but ill try to get a copy of the shop .
Im so pissed right now
Nobody knows, the warranty is overdue
Could I open the phone and maybe fix it myself?
I got the service manual but not the tools, anyone ever seen the inside of the phone, would it even be possible to fix it?
bump ...
similar problem
Hi there
i had a similar problem - had to buy another htc 8125 and unfortunately it came with a broken slot for the minisd card. At first i thought i wasn't pressing the card enough for the thing to click and hold it. Then i realised it was broken. As far as i could see from the little opening there was a white slider which is pushed down by the wider side of the minisd card. It has a spring behind it and somehow it has to click in down position and hold the card.
i tried to push it down with a very very small screwdriver and understand the way it worked. With my bad luck i pushed a little harder and broke that white slider. It just broke in the middle and one part stayed down and the other was pushed up by the spring. It broke exactly at the place where it was pushed by the memory card. So my card was not jumping anymore out - it just stayed in but was not recognised by the phone.
I didn't know what else to do so i found some instructions on how to open the phone and went for it with the hope to reach the memory card slot an hopefully fix it. HTC has taken good care of the stupid slot. It is soldered to the motherboard and nothing much could be done. There are 4 points that hold it but i didn't go that far to unsolder it (didn't know how many springs and other parts would jump out of it). Anyways - what i noticed was the following:
there are two small "plates" at the bottom of the slot. Wheny ou isnert the card they touch and i think this is what makes the slot active and knowing that there is a card in it. I had some dirt betwen them and that was preventing them from making a contact. After i removed that small piece of dirt and inserted the card it worked like a charm. It stays so tight in there now that i hardly can get it out - which is not that bad because i can always use the usb cable to transfer whatever i want.
I think i still have those manuals for opening the phone, so if you decide to go this far and can't find them i can send you an email.
Hope i was of any help
There's no need to open or disassemble the phone to repair the slot,just apply a thin layer of any adhesive tape around it but make sure you do not cover the connectors and insert the card firmly in the slot.
Cheers !
But well even if I push it in it doesnt get detected(I added a piece of paper to hold it in but it didnt detect it still).
I think ill buy a torx screwdriver and open it.
I'll still advise you to check the mini sd in some other phone,if it still doesn't get detected than get a new one or it may need to be reformatted.Opening up the phone might lead onto more problems.
Cheers !
zabardast_1 said:
I'll still advise you to check the mini sd in some other phone,if it still doesn't get detected than get a new one or it may need to be reformatted.Opening up the phone might lead onto more problems.
Cheers !
Click to expand...
Click to collapse
I got a 2gb minisd and a 512mb minisd both dont work so im sure its the phones fault , they have always worked fine.
Think it may have gotten sand in during a trip to the beach, and now SD cards dont click into place, and the unit doesnt recognise them, i took the back off and cant see anything obvious or bent pins. Dont suppose anyone has any advice before i give up on it?
The locking mechanism for your card reader is a small spring that is attached to a metallic pin inside the card reader itself. The way it works, obviously, is it latches on the way in and lets go when the card is pushed again. Can be 2 things - either you pushed a card in with too much force and broke (disloged) the pin, or the spring became detached. The only way to fix it is by opening and re-assembling the card reader, however, the metallic outer cover is difficult to remove and place back, I suggest you discuss the matter with a technician.
i just ripped te whole locking mechanism away
So...
I own a Bell Atrix. My carrier is Bell.
I flashed my phone with OLYEM 1.4.2.
Rooted it with Seven's script.
Made sure ADB was allowed to su.
Installed GingerBlur.
Phone got stuck in a reboot loop.
Re-flashed with OLYEM.
Now, I cannot mount my microSD. The settings show as unavailable and the manual mount is greyed out. I have tried a battery pull, a different microSD etc. My microSD works flawlessly in a different phone. I really do not know what crapped it. Was it GingerBlur, the flashing or just bad luck...
This means I cannot root the phone anymore and im stuck with OLYEM and a defective phone.
I took the phone to Bell for repair. They said it's been over 30 days from the buy date so they have to send it to an external firm to have it checked... I just hope they will not come back to me saying I voided my warranty.
Please let me know if you have had this problem or if you think there is something to be done if worst comes to worst.
Thanks!
I had the same issue but it wasn't related to updating. I had to take the sd card out and press down on the metal piece that holds the card in place to get it to have better contact. This worked for a while and then i pressed down even harder and it wouldn't read at all so I had to stick something under the metal thing and pry it back up and now it works great.
Just semantics, but it should be "micro SD", rather than "mini SD" (which is a different card type).
brucewee said:
I had the same issue but it wasn't related to updating. I had to take the sd card out and press down on the metal piece that holds the card in place to get it to have better contact. This worked for a while and then i pressed down even harder and it wouldn't read at all so I had to stick something under the metal thing and pry it back up and now it works great.
Click to expand...
Click to collapse
What did you stick under it to pry it back up? I may have to do this myself so I just want to know,
M.k.s said:
What did you stick under it to pry it back up? I may have to do this myself so I just want to know,
Click to expand...
Click to collapse
I used the semi-pointed but round end of a nice pen to press it down and when I had to reverse it I used the nail file part of some little finger nail clippers. Just stuff I had sitting around at my desk at work
Thanks for the suggestion! If I get it back and it's not fixed, I will try that. Bell rep told me it would take from 3 to 6 weeks. Yeah... 6 weeks.
Meanwhile, they gave an HTC Desire Z. I really like SenseUI. It works so much better for me when I compare it to Motoblehh. However, I do not like the feeling of the phone. The movable parts do not appeal to me.
Thanks again!
The Bell rep also told me it was the first Atrix they sent back for repair...
Ok, going really basic and this probably is not your issue, but I just had the same issue with a camera and one phone not recognizing one of my cards. I had to reformat it in windows and it has worked perfectly since. Probably because I was switching between so many devices or just coincidence, just passing this on.
Sent from my MB860 using Tapatalk
i just get this issue i want to try gingerbreak and i couldnt find my micro sd i reboot and so on many times, perhaps i make it work you need push pretty well, and try moving when its on the phone
brucewee said:
I had the same issue but it wasn't related to updating. I had to take the sd card out and press down on the metal piece that holds the card in place to get it to have better contact. This worked for a while and then i pressed down even harder and it wouldn't read at all so I had to stick something under the metal thing and pry it back up and now it works great.
Click to expand...
Click to collapse
There are two metal plates that need to make contact - if they don't the card isn't detected.
http://guide-images.ifixit.net/igi/JhXk4VIeX3CahwaY.huge
In the lower left of the sd card slot you can see the two plates. When the card is in the slot, these two plates should touch. When I got my phone, they were not touching, so I bent them slightly to make the contact.
If the link doesn't work, just go to the iFixit teardown and look at the pics at the bottom of the first page.
Fixed
I just got my phone back. Looks like the firmware flash was what broke the phone. The repair slip shows a software update only.
Im just happy they repaired it. I think I will wait for a Bell SBF...
Thanks!
"Your NOOK has turned off completely."
Yikes. So today I discovered there was something wrong with my NookManager SD card when my computer would not read it. I reformatted and wrote a fresh image and then wanted to make a backup (since the previous one was lost). I shut off my Nook without any problem.
But I nearly could not get it to come back on! And I never have succeeded in getting it back on (only twice so far) with the SD card in, so I haven't been able to do a back up {smoke comes out of ears!}. It is fully charged.
I've always thought the switch on the back was a little wonky but this is so sudden and, of course, at the worst possible juncture. Is there something I could have done in the system which would make the Nook difficult to turn on? Or is my number simply up and the power switch is all-but failing?
ADD: I just popped the SD card out for a sec and tried again and it came on almost on the first try. It reads the normal SD card just fine (where books and such are stored). Can there really be something with the NM SD card that is keeping the device from turning on? I just tried again with the storage SD card in place and the Nook started up once again without problem... And now it won't....has to be the switch?
EDIT: It's got to be the $#%& switch. I finally got it to come on with the NM SD card inserted and did a backup--which I copied over to my laptop. I tried invoking a reboot via wireless ADB with the NM SD card inserted to see if a warm boot was sufficient to the task. It worked! I may never turn off my Nook again.
nmyshkin said:
EDIT: It's got to be the $#%& switch. I finally got it to come on with the NM SD card inserted and did a backup--which I copied over to my laptop. I tried invoking a reboot via wireless ADB with the NM SD card inserted to see if a warm boot was sufficient to the task. It worked! I may never turn off my Nook again.
Click to expand...
Click to collapse
I had a similar problem when my Nook was almost brand new, I came to the conclusion that it was a problem with the way the microSD card was inserted, it wasn't right somehow. I had problems when I first had the NST with getting it to work with a card inserted. SO, there may in fact be an issue with your card.
That said, now that I have had my Nook for a while, and made much use of the on/off button, I do indeed have issues with it. I practically have to grip it with visegrips to get it to do anything. I plan to remove the plastic button and investigate further soon, I will try to let you know what, if anything, I find out when I do.
I do already know that it is a more or less typical metal dome.button switch I suspect it has become deformed with use.
More when I have details/proof.
MildBill
---------- Post added at 04:25 PM ---------- Previous post was at 03:42 PM ----------
MildBill said:
I do already know that it is a more or less typical metal dome.button switch I suspect it has become deformed with use.
More when I have details/proof.
MildBill
Click to expand...
Click to collapse
Well... Color me embarrassed...
It is, in fact, a sealed solder-mounted part, probably containing the above type dome/button, but it is a discrete part. At least on my NST.
I did, however, find that the screw just above it, that holds the case back in place (it slides off once the screw (AND the SD card!) is removed) was slightly loose, as were all the screws inside that held the circuit board to the front case. Not significantly loose, but a good 1/3rd to half turn for the inside screws, and maybe a bit more for the one above the switch.
Also, there was a fair bit of ... dirt, dust, white stuff, I dunno what it was, but we'll call it dirt for the moment, between the external switch cover/button and the case itself.
So, I cleaned that all out (a good blast of canned air), removed the back case and tightened all the screws, replaced the case back and the screw that holds it in place, and popped the external 'button' for the switch back in place.
End result, the switch now seems to work much more easily and reliably, without having to use a 'death grip' on the button at all.
This is the second time I have been inside my NST, and I found the tear-down instructions online, somewhere. It has been a LONG time, so I don't remember where, but I'm sure you can Google for it.
MildBill
P.S. I should also say thanks to you, for being the prompt that got me to fix my own issue with the switch, it was driving me bonkers at times, but in itself wasn't enough to make me break out the tiny screwdrivers! SO, here's to you, fellow Nook user, and I hope my story helps you!
MildBill said:
This is the second time I have been inside my NST, and I found the tear-down instructions online, somewhere. It has been a LONG time, so I don't remember where, but I'm sure you can Google for it.
Click to expand...
Click to collapse
Yipes... I've done just about everything else to my poor Nook but I'm really timid about opening it up (although I generally take wayward electronics apart at the drop of a hat). I dislike cases that were not meant to ever be opened again by human beings. Too much chance of cosmetic damage. But...... I'll soldier along with it using ADB to initiate reboot until I encounter a situation where that does not work (or my Nook freezes and I can't get it to reboot with the power button....).
But thanks for letting me know and indicating there is a way to get inside. I think I must have come across that also at some point and probably shuddered at the thought!
nmyshkin said:
But thanks for letting me know and indicating there is a way to get inside. I think I must have come across that also at some point and probably shuddered at the thought!
Click to expand...
Click to collapse
Actually, other than popping out the power button on the back, which is pretty easy, the case opens nicely.One screw, which is under the power button (and a paper tamper seal ), and with no card in the card reader slot, you simply slide the case apart and the back comes loose from the front easily. And, slides back together just as nicely.
Let me see if I can find the tutorial on how to take it apart. I'll edit with the link if I do...
MildBill
EDIT: Here's this one, focus isn't always great, but at least the action is always onscreen. I used a very small screwdriver instead if the Simcard, you could also use what's called a splooge, a plastic thingy for prying apart plastic cases... You will also need a T5 torx driver.
http://www.youtube.com/watch?v=q7U7TfBIXH0
I use the small blade on my Swiss Army knife.
If you push the power button very gently (not actuating) you will cause a gap in the lower edge.
Insert the blade a bit under the edge and pry both upward and outward.
I do this a lot.
I do this a lot.
Lol Probably more than anyone else in the civilized world!
OB
Sent from my SPH-D710VMUB using Tapatalk 2