I have an imate jasjar
I need to do a soft reset.
My standard soft reset button (external point) is broken, doesnt work.
MY VGA screen is not showing certain menu items at the bottom. So installing software isnt much help.
Q: Is there any way to run a soft reset from finding the soft reset *.EXE in the windows directory of WM5 on the pocket pc ?
What other means of running a soft reset do I have ?
Taking the battery out for a while seam to instigate a soft reset...phew !
Related
I have loaded this program on my JAM, and it keeps resetting, can not use the device at all!
I DIDN'T HAVE ANY PROBLEMS WITH VERSION 1.11
Has anyone experienced the same problem? Any solution?
Thank you
It works fine on my blueangel.
You may try to hardreset your machine and install it again.
I have updated the rom and installed right after, reset and so on and still didn't work.
I have repeted this about 4 times with different ROM's
A.
Its working fine on my Qtek S100 with 1.11.00.WWE; its just a pig and insists on being installed in main memory - everytime I try to move anyof the DLLs to Storage, I have to do a hard reset..
Hi!
I am also using BatteryPackPro v.2. The problem I am facing is that sometimes when I am connected to my computer thru BT, the program memory on my Jam keeps decreasing. It keeps going down and when I disconnect it just stays at the same point till the time I do a soft reset.
Any suggestions?
there is an update 2.0.3
the update fixed the mapping of botton
I have this problem on my magician....everywhere i tap (active sync-program folder-file explorer.). the program don't start....i f i push contact button it say: memory program exausted___goto settings---memory and close all program .....but i have all empty! 22 megabyte of memory program and 22 of memory storage...how can i solve this problem? what's happened!I cant' do a hard reset because i have documents on my phone and activesync don't work!!!
PLEASE HELP ME!!
Hvae you activesynced with your pc?
Do that first to copy off what you can.
Then, just soft reset the PDA (NOT hardreset).
What happens then? Do you get the memory problems from soft reset?
Try soft reseting and leaving the usb lead cable attached to get activesync to backup your contacts etc immediately after PDA boot up.
What CAN you do? Does the start menu work? Does the control panel work?
V
too
It happens to me sometimes too.
A soft-reset usually works for me.
(I hate how much i need to do that b.t.w. I NEVER had to reset my Psion in the 6 years I used it!)
greetz,
Pfeffa-rah
I was installing MS Voice Command to my s200 and at the s200 there was an error and installation was not successful. After this I can not see the softwares installed in my s200 at Settings/Remove Programs. Also activesync started to give an error and I can connect as Guest :?
What is the problem and the what can I do to repair? I wish there was something like system restore in WM5. I hope I wont have to hard reset.
Need help here :roll:
Hard reset does not always have to be so bad!
Look at it from the bright side:
You have a clean device again and installing your software via active sync (if you have installed it via this way before) isn't all that difficult either.
Cheer-up and make sure to buy sprite back up for when it happens again to you.
Robin
Ok that is fine. But anyone knows what may cause this and if I can solve without hard reset. :roll:
Seems no!?
I don't how and why but but I have lost some program fom my qtek v1605 (with a HTC Rom) and I can't make a hard reset with the "1234" because impossible to enter in the program : Is there possible to make a hard reset manually ?
When I try to make a hard reset : vocal button (on left) + Wireless Manager button (on right) + soft reset -I don't know if it's the good way- and I see this message :
Select KITL Transport :
USB KITL (already selectionnes & impossible to change)
ethernet KITL
USB KITL
select KITL Mode :
Active (already selectionned & impossible to change)
Passive
HTC_DEV
impossible to use any button to activate something
I'm so degusted
What do I have to do ?
THX
to do hard reset, read this on the wiki.
Which is the Left SOFT KEY and the Right SOFT KEY because for each side you have 2 buttons......
funkabyl said:
Which is the Left SOFT KEY and the Right SOFT KEY because for each side you have 2 buttons......
Click to expand...
Click to collapse
It's the two buttons with dashes on i.e. the one above the windows key and one above OK key. Press these at same time as inserting stylus in hole to do a hard reset.
Mike
Thanks Mike for the follow-up.
I've upgrade to WM6 from W2003SE.
Then I make hard reset push camera and record buttons.
then I must choose to Clean Registry Hive and “Format Storage” but the
buttons don't work so I can't choose.
What can I do?
I'm just wondering if you managed to resolve this problem. I having the same issue with my pda2k with an upgrade from wm5 to wm6 .
Tks,
MC