Database Users

I need help to repair my Qtek

Hello
I just did the following :
download the files from www.carrierdevices.com.au for Qtek 101 update
"Qtek 1010 Upgrade
(22102003-190723)-RSUv1.15_(GPRS_T32500_ENG).exe
File Contents
• CE Upgrade File : RUU_CEv3.18.04wwe_Qtek_SHIP.exe
• Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe
"
When the process began there was an error asking to press OK for restart.
After restarting device in the boot sequence ( when logo is diplayed) there are no informations about the ROM. Just Radion version is diplayed and that is the new version one (3.25)
Also on the display there is no start icon and I cannot use the display because it seems to be decalibrated completly.
Very Important : When I try to connect to Activesync after a while it telling me that the device is not a smartphone or a pocket PC and cannot be connected. So I cant use any program to try to upgrade again.
What to do ?
Please try to give examples and link to download files in order to fix my device.
Thanks in advance
Silviu C.

Hi ...
If you still can get to the boot loader screen (power button + soft reset) and it displays "GSM OK", that means there is a good chance that the flash ROM is not damaged.
You can either put the ROM and RSU files on SD card through a card reader (.nbf files) or to get a valid SD backup for CE + Radio from any working XDA and use the boot loader screen to flash your device again.
Good luck ...

thanks, where I can get some files?
Thank you for your replay,
It seems to be ok cause i can upload a new CE in SD format to the device. ROM was build in the kithcenROM from yorch.net.
It still not working cause perhaps I need the file containing Radio and CE as well in SD format.
Do you know where I can get it ?
I dont think I can get another device to read the files on the SD.
Many thanks,
Silviu C.

I 'm not sure which stage you are stuck with now ... if you can put CE image on SD card and flash it using the boot loader, that means you can boot your XDA and flash the RSU through a normal EXE file from yorch.net .... if this is not the case then you most propably have the wrong file format on the SD card.
Give more details plz

present situation
I am at the edge of disperation.
Steps of what I did :
1. Back up Boot and CE to SD and save them to HDD.
2. Build a CE from Yorch.net in nb1 format and write it to SD with an adaptor.
3. Flash the device with that specific file ( was just CE , not including bootloader)
Now, my pocket is like that:
It cannot been powered from the power button
It start when plug in the charger
I cannot go in bootstrap mode ( when procedure for activating is made I just got a small red flash from the LED)
I have to mention that I choose from the yorch options :" lock butons except power when the device is turned off "
So, now I cannot use the SD for try another flash image.
I cannot use activesync because it cannot recognize the device. Somthing is wrong in the header of the authorising string or something like that.
When I plug the USB cable, activesync is starting but after 10 secs a pop up telling me that the device cannot be recognize, it is not a smartphone or pocket pc.
I am stack.
Thank you
Silviu C.

another question
I have another question:
Is there anywhere - in situation that the problem with boostrap will be solved somehow - full flash containing both radio and CE ?
Thank you,
Silviu C.

some little success
I have suceded by entering in bootrap mode !!
It telling me that I have GSM ERROR
What to do?
IS there any way I can get a full flash for Qtek with radio and OS as well?
Thanks,
Silviu C.

In the boot loader screen, try to press the calendar button ... it should give you the GSM menu. Select "Reset" or "Turn off" and do a soft reset
Plz do NOT try band switching or "Calib/debug"!

It sounds like a failed radio stack upgrade, you can try copying the RSUpgrade.sa.CAB file to your SD card then run it from there.
You can get the RSUpgrade.sa.CAB file by using WinZip to extract it from the RSUv1.15_(GPRS_T32500_ENG)[1].exe file.
HTH

Details instructions for SD card upgrade to Siemens A.30.09

Hope this helps, this is a simple process, these instructions appear long and difficult because i've added quite a bit of detail.
Prepare Everything
1 - Download and install XDATolls http://wiki.xda-developers.com/wiki/XDAtools
2 - Connect your PocketPC and make sure that ActiveSync is running
3 - Delete all files on your SD Card (in your pocketPC)
Extract the ROM files & get ready for the upgrade
4 - Run the .exe file you download from Siemens, this will extract the files into C:\Program Files\SX56 upgrade utility. Don't proceed with the install, just exit it after the extract is completed.
5 - Confirm the existance of the file C:\Program Files\SX56 upgrade utility\english\NK.nbf
Using XDAtools (OS Image tool) transfer the ROM onto your SD card via your PocketPC and cradle (this is a new feature)
6 - Run the XDA OS Image tool (part of XDA Tools)
7 - As your source select the file C:\Program Files\SX56 upgrade utility\english\NK.nbf (directory is selected by clicking the square button with dots)
8 - As your destination select from the drop down box SD Card
9 - Click copy to transfer the file, if it fails check that ActiveSync is running & try again
Re-flash Image using Wallaby Bootloader method
** THIS WILL ERASE ALL DATA ON YOUR POCKETPC, you have been warned, make sure you've got a backup of everything you need.
10 - Plug your PocketPC into AC power & Make sure that your SD card is in the slot on your pocketpc
11 - Using the stylus top, hold down the left hand soft-reset, then press the power button.
12 - The bootloader should find the new ROM image on the SD card, press the action button to start the load (action button been the central click of the direction button)
13 - The load process will take about 5 minutes or so
14 - Once completed, use the stylus top and press the battery disable button, leave for 5 seconds then press it again to enable the unit.
Enjoy the new ROM, note that the first bit of any audio is played at a reduced volume, this doesn't help short ring tones nor fonix voicedial. Other than that the ROM seems quick and highly stable.

very good guide: question
do you know if this will touch the RSU?

no thats the whole point of copy'ng out the nbf file is that you dont mess with the rsu

which version is better?
thank you for your reply rudegar.
What version do you recommend for a SX56?
A.30 (cooked) , 4.01 (cooked) or the one released from siemens?
I heard that 2003 have some bugs, is it true? I have ppc 2002, is it worth the upgrading to 2003?

i dident have too many problems with my xda1 when i upgraded it to 4.01
org from tmobile
dident have a single SD card ereasing issue like some people report
but nor did i really think that the os was all that different

A.30 or 4.01?
What about A.30? what are the differences between both? which is better?

Problem with Xplode wm6.11 Upgrade

Hello
PPC: Blue Angel T-Mobile GER
Rom: Xplode Wm6.00.00.WWE
Radio:1.15.00
Protocol: 1337.45
From this rom i want to upgrade to Wm6.1 from Xplode.
My Upgrade steps:
1. Bootloader
2.The ppc shows "Serial"/"Usb" and "v2.05"
2.2 Kill Active sync
3. starting MaUpgradeUt_noID
4.MaUpgradeUt_noID gives no informations about the current Rom /upgrade rom
5.Next
6. Error 150
What i have to do?
Plx help me
Sry for my bad english!
Thx to all

It must be an OS problem
Try using Windows XP rather than using Vista.
I got the same problem with my XDA IIs,
I tried it in Windows XP and successfully Updated to WM 6.1

i have Windows XP no Vista

Give it a try without killing ActiveSync on PC.
1. Put device in bootloader mode
2. Put device in the cradle
3. Start update program (wait till 100% and do not remove device out the cradle)
4. When update has finished, hard reset the device
- If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, EITHER:
Quickly press "Record" & "Camera" before the versions appear at bottom right
OR press "Power" & "Camera" & "Record" buttons and Reset at the same time
- If you have a PH20B1 device such as SX66:
Quickly press "Record" & "Windows Media" before the versions appear at bottom right EITHER
OR press "Power" & "Windows Media" & "Record" buttons and Reset at the same time
You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.(“Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES)
- If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, use "Camera" and the "Record" buttons.
- If you have a PH20B1 device such as SX66, use "Windows Media" and the "Record" buttons.
Note: The "Record" button moves up and down the menu and the "Camera" button toggles Yes/No. When you're done, press the button in the middle of the D-Pad to continue booting.
- Press the "Mail" button. A white screen will show for 30 seconds, while it is clearing your device in preparation for the new ROM to start executing
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
(if removed earlier) Put back your SD Card before you do the setup. This way the installation from the SD will continue after you have done the setup
5. Your upgraded ROM is now running!
Greets Rossi

windows 6.1 VODAPHONE VPX (XDA, dopod, HTC - blue angel

Please where can i get Windows 6.1 on my VODAPHONE VPX (XDA, dopod, HTC - blue angel).Looking forward to hearing from you.

look here in sticky subjects for sun-dream,you will find it

since no one is replying, i do the job:
WM6.1 CEOS 5.2.20758 Build 20758 Aku 1.4.1 WWE
16MB RAMDisk,25.2MB PP
http://www.brsbox.com/filebox/down/f...and/1181621103
Password for extracting the rar file:
2qfewrwF$W%567%wwba
there is nk.nbf file in it, Extract it to C:\rom directory.
Now download BAA RUU (installation utility)
http://moeenweb.110mb.com/rom.zip and extract it to C: drive. (remember nk.nbf should be in rom folder in C: drive.
Now:
1. Take Mem card out of your blue angel
2. put blue angel in bootloader record + on/off button + reset
3. Connect it to usb cable
4. run MaUpgradeut_noid.exe
5. just clickity next next next and then finish after the update is complete
6. Now press reset button and sooner ur phone is resetted press camera + record button together until u get a 4 colour screen with a menu
do this press camera to switch options, press record button for yes/no
No for enable KTTL
Yes the other two options
press inbox button and u r done

ode 402: Cannot communicate with device fix

Since the day I bought my iPaq 614 I wanted to update it to the newest version, but every time the HP RUU would return a "Code 402: can not communicate with device". I've searched for hours to fix this problem only to find out tips like 'disable your firewall and A/V' and 'don't use Vista'. But today I found the solution:
Normally, Active Sync acts as a DHCP server for your Windows Mobile device, but this doesn't work if Windows Mobile isn't running which is the case when you're flashing a new ROM. In this case, the Internet Connection Sharing service should deal with assigning the right addresses, but since I normally don't use ICS, I had this service disabled.
Because of this, no addresses where assigned and no communication path could be set up between my computer and my iPaq. Simply be re-enabling this service (and the dhcp client service, don't know if you really need it, but I enabled it just to be sure) I fixed the annoying code 402 error
Hope this information is helpful because it looks like I'm the first one to discover this solution
//edit: damn, can a mod change add a 'C' to this post's title

i got a code 402 while updating RUU_1.8.0_081208_MP_M089_WWE (radio fm 0.89) now i am stuck withthe HP blue screen.

If your 614c dies during radio update, please have a look here.

solved !!!
Found post on HP forum.
OKâ ¦unfortunately previous note wasnâ t so accurate.
Iâ ve tried this solution once again and it doesn't work properly.
Iâ ve spend much time reading many articules on pocket/mobile forums and I found 2 workaround methods to upgrade our iPAQs.
Starting from the beginning.
We have to download ROM from HP Support site (in *.exe format) and executed it to unpack all files (as Iâ ve already written in C:/iPAQ ).
Among many files that we have, find FLASH.NBF file and edit it using HEX-editor (i.e. xvi32). When we display the context of a file, we have to delete first 3432 bytes (in xvi32 editor - XVIscript > Editorâ ¦ > type command DEL 3432 and press Execute â then close the editor without saving and then save file on HDD as FLASH.DIO). When we create FLASH.DIO file we have to decide which method weâ ll use.
1. METHOD is:
Just copy FLASH.DIO file on empty microSD card. Put inside of our device and turn it on in SDLoader mode (VOICE UP + OK + RESET). Important thing is to fully charge the battery of the device.
2. METHOD is:
We change the type of FLASH.DIO to FLASH.nb0 â just rename.
We have to search network for DNW app and execute it. Firstly in Configuration tab select Option and change connection type from 0xc000000 to 0x3000000 (USB). Secondly turn on our device in DOWNLOAD IMAGE mode (VOICE DOWN + OK + RESET) and connect it to PC. In SEC folder (subfolder of DNW) we can find drivers that we have to install after connecting iPAQ. When weâ ve covered everything, we select USB Port > UBOOT > and select our FLASH.nb0 file.
For me worked first method!