i get a new rom from the internet and i didn't compleat the installation because my pc restart throw installation and my phone
stuck on the IPL\SPL screen and the OS didn't start
and when iconnect my phone to USB the activeSync didn't start too
and now phone readed to
please Help what can i do ??????
tarecko said:
i get a new rom from the internet and i didn't compleat the installation because my pc restart throw installation and my phone
stuck on the IPL\SPL screen and the OS didn't start
and when iconnect my phone to USB the activeSync didn't start too
and now phone readed to
please Help what can i do ??????
Click to expand...
Click to collapse
Activesync will not work in bootloaders (multicolor screen),its stuck at the bootloaders with ipl/spl display due to bad flash. What IPL/SPL...? it displays.Which Rom you downloaded and tried to install ?If your phone is a G3 device,is it CID unlocked ?, try to Soft Reset or HardReset,sometimes it helps,but if it doesn't,then you'll have to flash the rom again in bootloaders mode.
Cheers!
Related
cingular 8125.
I need the original rom file (original firmware )can anybody help plz right now my fone stuck on the RUU mode can anybody help
If it is realy a brick without any chance of life I need a part of it: the keypad.
Thats really rude.
not a complete brick yet
not a complete brick yet is in loader mode red,blue ,green screen
All the cingular roms are here ftp://[email protected]/Wizard/Roms/Cingular/
user name xda password xda
which rom do you have?
It looks like you are in bootloader (multicolored) mode so that is good
connect via usb - you dont need to activesync to update rom. You should get a usb sign bottom left of screen and then start update.
Upgrading without activesysnc
After a interruptus ROM upgrade my s200 d'ont start . after the HTC i have a white screen but not more.
The activesync don't connect and i can't put the ROM another time.
I obtain the multicoloured screen with usb in the left botton.
Please, could anybody help me to update the rom in this situation , mayby without activesync ??
Regards.
You can flash a rom from the 3-colored bootloader mode (hold voice button when turning device on). When it says usb you can just flash without activesync.
Yes thank's i found a ROM that don't need activesync , after that i had changed that rom by my rom and at the moment my s200 y ok.
Thank's.
Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!
Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
it is time to donate to XDA-developers!
Just reflash the ROM, friend. Seems to be a bad flash to me.
deleted this post
wiztek said:
Hi Wizards,
Im having a Qtek 9100 and using a ROM cooked by Mfraazz. The phone application seems to hang and i have to reset in order to make it functional...the problem does not end here. When the phone boots up, the start menu bar is not visible...I have to hard reset my device 3 -4 times..thats whn the start menu is visible..
I have only one application(Good Link) running...plz help me guyzz
Click to expand...
Click to collapse
try another cooked ROM or an official one and see if problem persists...
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
z0d1ak said:
the mfrazzz crossbow reloaded made my kjam hang on the bootloader as well n my fone cant b detected by active sync either plz help how m i suppose to flash another rom wen active sync itself dont detect my rom
Click to expand...
Click to collapse
Rom has got nothing to do with Activesync not detecting your phone,it's most probably the problem of Activesync application or your USB cable not establishing connectivity.Check the usb connectivity for problems.To verify the connectivity,check if it gets charged via usb connection.
secondly,get your phone into bootloaders and connect it to your Pc via usb cable,see if usb appears at the bottom of the bootloader mode (multicolor screen),if it then it's connecting.
You don't need Activesync for flashing a Rom to your phone,it's done via usb cable,and while flashing activesync is automatically turned off by the Ruu.So if you are able to establish connectivity via usb cable in bootloaders (multicolor screen) you can flash to any Rom.
Cheers
Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.
Hello everyone!
I got a HTC Prophet with english windows mobile. I've wanted to install a german ROM, and used this:
http://www.handy-faq.de/forum/htc_p...ophet_touch_ix_rom_deutsch_download_1005.html
I've runned a .bat file and the installation startet. But then i closed the window with the installation insinde (undeliberate). and now the prophet won't load windows. it always stops at the boot screen, where the infos are:
IPL 2.15.0001
SPL 2.20.0001
I can run the BootLoader mode and connect the Prophet to my PC. on the left bottom it says "USB" but when I run the installation again it says "no device connected".
i got windows 7 ultimate in 32bit version.
I hope you can help me, 'cause it's the phone from my dad and i won't get him angry
Greetings from Germany!
Bianca
geffi said:
Hello everyone!
I got a HTC Prophet with english windows mobile. I've wanted to install a german ROM, and used this:
http://www.handy-faq.de/forum/htc_p...ophet_touch_ix_rom_deutsch_download_1005.html
I've runned a .bat file and the installation startet. But then i closed the window with the installation insinde (undeliberate). and now the prophet won't load windows. it always stops at the boot screen, where the infos are:
IPL 2.15.0001
SPL 2.20.0001
I can run the BootLoader mode and connect the Prophet to my PC. on the left bottom it says "USB" but when I run the installation again it says "no device connected".
i got windows 7 ultimate in 32bit version.
I hope you can help me, 'cause it's the phone from my dad and i won't get him angry
Greetings from Germany!
Bianca
Click to expand...
Click to collapse
Hi this is a easy problem to fix dont worry but first u need to read this http://forum.xda-developers.com/showthread.php?t=353547 you need to hardspl your device first then install the NVID rom in the link read the recovery solutions carefully oh and about active synce try this
Go in to Active Synce settings and uncheck allow usb connections that will help to detect your device when flashing the NVID rom after that just use any flashing tool to install the rom on your device problem solved just read the link if u dont understand as this happened to all of us before so we understand how u must feel
Hope this helps
Heya and thanks for your answer!
I did read the terms of use in the post u linked, but I got always the same problem:
No device is found. on the BootLoaderScreen it says "USB" and Windows 7 detected the Mobile Phone.
But the HardSPL didn't found the phone
I try to take the battery out and put it in after one minute, but it didn't work
geffi said:
Heya and thanks for your answer!
I did read the terms of use in the post u linked, but I got always the same problem:
No device is found. on the BootLoaderScreen it says "USB" and Windows 7 detected the Mobile Phone.
But the HardSPL didn't found the phone
I try to take the battery out and put it in after one minute, but it didn't work
Click to expand...
Click to collapse
Did you try flashing the NVID - AKU 2.* WM5 rom for recovering your Prophet on your device first then hardSPL your device? you need to install the rom first then hardspl it after that flash any other rom here http://www.4shared.com/file/57952591/3955ed98/NVID_RUU.html?dirPwdVerified=2948f2e flash this to your device and remember to uncheck allow USB Connections in active sync and just it should work if u still need more help al be happy to help you out and since ur using windows 7 use this tool to flash any rom to your device ok http://forum.xda-developers.com/showthread.php?t=534707 since am using both vista and xp and they work well so remember flash the NVID rom first then hardspl and try flashing back the rom you wanted to use on your device ok
hey!
i installted Windows XP and then load the HTC Prophet in BootLoaderMode.
I do HardSPL and it works. Then I install thisNVID. The phone rebootet, but windows didn't load. when i try to install the rom (i posted the link in first post) but it says already, that no device is connected.
the phone didn't load windows
geffi said:
hey!
i installted Windows XP and then load the HTC Prophet in BootLoaderMode.
I do HardSPL and it works. Then I install this NVID. The phone rebootet, but windows didn't load. when i try to install the rom (i posted the link in first post) but it says already, that no device is connected.
the phone didn't load windows
Click to expand...
Click to collapse
Sorry but first you need to recover your device by first installing the NVID rom and good u have windows xp did you did what i said about active sync uncheck allow usb connects then flash the NIV rom then use lazytool thats what i use on my windows xp to flash the rom u wana use what happened when u try to install the NVID rom? first you must manualy go too the bootloader menu in other to flash it you know reset the device and hold both the commanager and camura button until you enter the bootloader menu then flash the NVID rom if it works then do a hardspl then flash any roms using lazytool it should work when u said the phone rebooted but windows did not run what did you see on the screen? after the reboot? also the NVID rom is windows mobile 5 so you device should boot up windows but al look into this for you ok
PS this is important you should know that your device is G3 or G4 and from the looks of you spl it looks like a G4 device this is very important beouse if u flashed with G3 you can damage ur device but dont worry the guys here have managed to fix this so if ur flashing any rom use the G4 option ok but please look over these instructions http://forum.xda-developers.com/showthread.php?t=353547 as they helped me when i had the same problem
I just Private message you check ur inbox