Wing for NOOBS like me.
All information in this thread was copied from other peopled, all I have done is put it in one place.. I will update this from time to time
For updates please check the site I have created for the wing.
DISCLAIMER:
I am in no way responsible the content listed below, most of this should work as the people of the community do help each other. Please be careful. And report any errors to me.
Adding Information, If you wish to add information to this post, please post it below, I will add the info, please provide me a link to the data if you have it, and the original writer of said info, I will give the credit to the writing and the provider of said info.
Part 1: useful thread Post.
Part 2: Random tweaks from HOFO.
Part 3: Rom’s Touch it Wing 2.3
3a Touch-IT for The Wing Full and Lite Ed.
Part 4: Random Info
Part 5: T-Mo Wing RUU for USA
Updated on December 17 2007
Part 1: Useful Threads
Cab install for the Wing
The Following is from zcink @ XDA
Original thread @ http://forum.xda-developers.com/showthread.php?t=341867
Great Wing Info Thread
The following is from Nyer78 @ XDA
Original Thread @ http://forum.xda-developers.com/showthread.php?t=326655
General HTC Cabs
The Following is from patr!k @ XDA
Original thread @ http://forum.xda-developers.com/showthread.php?t=344533
Part 2 tweaks.
The Following is from – Tater_Tot24 @ Howard forums
Original thread @ http://www.howardforums.com/showthread.php?t=1215155
Please Note that some of these entries only apply to the WING.
Add Side Button Functionality:
1. Using a registry editor go to HKLM\Software\Microsoft\Shell\Keys
2. In Keys, create a new Key named "40C7".
3. Copy the contents of 40C5 to to 40C7.
4. Edit the "Name" value replacing the "4" with a "5" (5 is Voice command button).
5. Close the registry editor.
6. In Settings\Buttons you should see the new "Button 5(Hold)" entry. If not, soft reset.
Note: I had to make voice command the hold function and screentoggle the non hold function for it to work correctly.
Camera Settings:
1. Open the camera, so you can see images thru the camera lens.
2. Go to bottom of screen & click on the "Y" at far left side.
3. Now move to the 4th icon at the bottom, and set the resolution on "L" and the quality on Super Fine (not Basic).
4. Move to the next icon on the right, and set the Capture Mode on either "Burst" or "Sports"
5. Next, click the icon at far left and set your Capture Speed to either Moderate or Fast, and "Snapshots" to at least 3.
6. Click on the next icon on the right and set it on Storage Card.
7. Finally, click the "Sun" and set the White Balance on Auto.
8. Click OK in the upper right, and you're almost set. Just go now to far left of camera screen and click either of the tiny > arrows until you come to 1/3 (or 1/5 or 1/7 or 1/10, depending on how you set "Snapshots.")
9. Now you're set to take some really great pictures. They will be sharp & clear all the way from about 12 inches to infinity.
10. For sharper pictures, leave the setting at 1x. Anything else is a "Zoom" shot.
Enhanced File System Performance:
Registry: HKLM\System\StorageManager\FATFS
Key: CacheSize (dWord)
Default: 0 (I am not sure what this equates to, the valid values I know about are 4096, 8192, 16384)
New Value: 8192
Hide SIM Contacts:
Registry: HKCU\ControlPanel\Phone
Key: ShowSim (dWord)
Default: 1 (show)
New Value: 0 (hide)
Active Sync Running in the Background Fix:
1. Create a “Fake Server”
Configure Server Menu Activesync Programs 2.Go to Start
3. In the following screens you can enter any old garbage. It does not matter, but just in case your unsure, just type the following in the indicated boxes:
4. Server Address: fake / User name: fake / Password: fake / Domain: fake. Then you are finished creating the fake server
5. Finally, UNCHECK the box in the time zones tab in the phone settings (This may sound silly, but it works! I promise!!)
MyFavs Missed Call Fix:
Registry: \HKLM\Security\Phone\NoLog
Key: List
Action: REMOVE
Hard Reset Instructions:
1. Hold down both of the “soft buttons”
2. Perform a soft reset with the stylus while still holding down the buttons
3. Push the green phone button to confirm that you do want to do a hard reset
DeBrand the Phone:
1. Perform a Hard Reset (instructions listed below)
2. Phone cycles through format, installs WM6, then prompts you to config touch screen
3. Install finishes and loads WM6
4. Then a prompt appears warning that EXT ROM will install extra contents (don't install! poke the soft reset button before EXT ROM install)
5. Hit soft reset button when EXT ROM prompt appears, you have 3 seconds!
6. Power on like normal
Send Large MMS:
Registry: HKLM\Software\Arcsoft\ArcSoft MMS UA\Config\UI\Size Limit
Key: wap2sendlimit1 (you can also change wap1sendlimit1)
Default: 307200
New Value: 1228800 (1200K)
Set the new value by going to Text/Multimedia --> Menu --> New --> MMS --> Menu --> Options --> MMS Options --> Servers --> T-mobile MMS
MMS Sending Issue Fix:
1. Due to incorrect Port setting for the MMS server, the phone may not be able to send MMS messages all the time.
2. Go to Text/Multimedia --> Menue --> New --> MMS --> Menu --> Options --> MMS Options --> Servers --> T-mobile MMS
3. Make sure the settings are set to: Gateway: 216.155.165.50 / Port Number: 8080 / Server: http://216.155.174.84/servlets/mms
Remap Soft Buttons:
For Calendar
Registry: HKCU\Software\Microsoft\Today\Keys\112
Key: Default
Default: Calendar
New Value: Internet (anything you want goes here)
Registry: HKCU\Software\Microsoft\Today\Keys\112
Key: Open
Default: HTCCalendar.exe
New Value: \Windows\iexplore.exe (again, anything you want goes here)
For Contacts
Registry: HKCU\Software\Microsoft\Today\Keys\113
Key: Default
Default: Contacts
New Value: (anything you want goes here)
Registry: HKCU\Software\Microsoft\Today\Keys\113
Key: Open
Default: \Windows\RSK\Contacts.lnk
New Value: (again, anything you want goes here)
Remove / Modify Startup Sound:
Registry: HKLM\SOFTWARE\HTC\StartupAnimation
Key: Enable (dWord)
Default: 1 (jingle on)
New Value: 0 (jingle off)
Registry: HKLM\SOFTWARE\HTC\StartupAnimation
Key: Volume (dWord)
Default: 127
New Values: 16 - 200
You can also modify the sound and animation by changing the WAV and GIF files in these two keys.
Registry: HKLM\SOFTWARE\HTC\StartupAnimation
Key: WAVFile (SZ String Value)
Default: \Windows\T-Mobile startup.wav
New Value: (whatever you want)
Registry: HKLM\SOFTWARE\HTC\StartupAnimation
Key: GIFFile (SZ String Value)
Default: \Windows\TMO_Startup.gif
New Value: (whatever you want)
Remove the Tray Icon from Today Screen:
Registry: \HKLM\init\
Key: Launch92
Action: DELETE
Note: If you want to keep some but not all of the icons:
Registry: HKLM\Software\HTC\TrayApplet
There you'll find listings for each icon (the folders are for the WinWap, MyFaves, and CommManager tray icons). Remove the ones you don't want and soft reset. If you remove the music player settings, you will then have to uncheck the plug-in from Today items.
Adding Slide Sounds:
1. First you are going to need two .wav files.
2. Once you have the two sounds that you want to use, Rename them to Slider3_in.wav and Slider3_out.wav and place them in the \Windows Folder on your phone.
3. Go to the Registry: HKLM\Software\HTC\SlidingSound\.
4. Once your there you should see 3 Folders (keys) that are labeled 0-2, and 2 Dword Files (ActiveSlidingSound and SlidingSoundEffect).
5. In that same directory, you need to make a new folder (key) and label it "3". Once that is made, you need to go inside that "3" which should be empty and have nothing inside.
6. Now you need to make a new String.Label the String "in" without quotes, and then set the string to "Slider3_in.wav". Now you should have one string inside folder (key) 3.
7. Now you need to make another String inside of folder (key) 3. Just follow step 5, but instead of using "in" use "out". So it should be labeled "out" and should be set to "Slider3_out.wav".
8. Next, create another String inside of folder and call it “Default” (no quotes). Now set that sting to whatever you want the new schema to be called (i.e. wind chimes, customer, etc).
9. Now head back to the registry: HKLM\Software\HTC\SlidingSound\, where you should now see folders (keys) 0-3 now and two Dwords files.
10. Now change Dword ActiveSlidingSound to 3, which is the new sound you created.
Disable the SMS Sent notification
Regisrty: HKLM\Software\Microsoft\Inbox\Settings\
Key: SMSNoSentMs (decimal)
Default: 0 (on)
New Value: 1 (off)
Note: Please note that the 'Settings' key may not exist in your device, and thus may have to be created first.
Storage Card Settings:
Mail Attachments
1. Go to Text/Multimedia --> Menu --> Tools --> Options --> Storage
2. Then check the box!
IE Storage
Registry: HKCU\Software\Microsoft\Windows\CurrentVersion\Exp lorer\Shell Folders
Key: Cache (string)
Default: Program Memory
My Value: \Storage Card\Internet Files\Temporary Internet Files
Key: Cookies (string)
Default: Program Memory
My Value: \Storage Card\Internet Files\Cookies
Key: History (string)
Default: Program Memory
My Value: \Storage Card\Internet Files\History
Note: Please see the “camera settings” to store pictures and video to the storage card.
Video from Portrait to Landscape:
Registry: HKLM\System\GDI\
Add key "Rotation"
Add Dword "LandscapeMode"=0
Move / Remove Startup Files:
1. make directory "\Windows\StartUpDisabled"
2. If you don't use MyFav5 Plan then copy "\Windows\StartUp\My5MsgCenter.lnk" to "\Windows\StartUpDisabled\My5MsgCenter.lnk"
3. If you don't use Voice Commands often (you can still manually start app) then copy "\Windows\StartUp\Voice Command.lnk" to "\Windows\StartUpDisabled\Voice Command.lnk"
Remove Services:
4. Go to "HKEY_LOCAL_MACHINE\Services"
5. If you don't use MyFav5 Plan (SMSCSend links to my5client.dll, I don't have My Fav plan, so I don't need this service)
a) save SMSCSend reg export somewhere for backup
b) delete "HKEY_LOCAL_MACHINE\Services\SMSCSend" from registry
6. Go to "HKEY_LOCAL_MACHINE\Services"
7. If you don't use Windows Live
a) save Windows Live reg export somewhere for backup
. b) delete "HKEY_LOCAL_MACHINE\Services\Windows Live" from registry
Other Services:
Other Services
"HKEY_LOCAL_MACHINE\Services\BTHIDSVC"
loads the Bluetooth Human Interface Device drivers and service
"HKEY_LOCAL_MACHINE\Services\BTAGSVC"
loads the Bluetooth Audio Gateway drivers and service
"HKEY_LOCAL_MACHINE\Services\BthAsPlugin"
loads Active Sync over BlueTooth service
"HKEY_LOCAL_MACHINE\Services\Trusted"
loads WSP Push, Push Router, SIM tool kit, SIM Init
"HKEY_LOCAL_MACHINE\Services\OBEX"
object exchange - protocol for data exchange between devices or syncing
"HKEY_LOCAL_MACHINE\Services\NOTIFY"
pop up notifications for events
"HKEY_LOCAL_MACHINE\Services\credsvc"
Credentials Manager
"HKEY_LOCAL_MACHINE\Services\CERTENROLL"
performs enrollment and renewal of certificates
"HKEY_LOCAL_MACHINE\Services\WirelessService"
Wireless Monitor Service
Increase voiceVolume:
Regisrty: HKCU\Control Panel\SoundCategories\InCall
Key: AttenuationCategory
Default: 2
New Value: 1
Regisrty: HKCU\Control Panel\SoundCategories\InCall
Key: InitVol
Default: 3
New Value: 10
Increase Voice Command Volume:
Registry: HKCU\Control Panel\SoundCategories\VoiceCommand1
Key: AttenuationCategory
Default: 3
New Value: 1
Registry: HKCU\Control Panel\SoundCategories\VoiceCommand1
Key: InitVol
Default: 5
New Value: 20
Better sound over A2DP
Registry: HKLM\Software\Microsoft\Bluetooth \A2DP\Settings
Key: MaxSupportedBitPool
Default: 30
New Value: 58
Registry: HKLM\Software\Microsoft\Bluetooth \A2DP\Settings
Key: BitPool
Default: 30
New Value: 58
Note: If not good enough, then delete: "MaxSupportedBitPool"=XXX &
"BitPool"=XXX.
Unlocks & Unhide the Extended Rom in Explorer:
Registry: HKLM\System\StorageManager\AutoLoad\TRUEFFS_DOC1
Key: bootphase
Default: 1
New Value: 2
Registry: HKLM\System\StorageManager\Profiles\TRUEFFS_DOC1
Key: mounthidden
Default: 1
New Value: 0
Registry: HKLM\System\StorageManager\Profiles\TRUEFFS_DOC1
Key: folder
Default: ?
New Value: Extended_ROM
GMail Settings:
You can access your Gmail messages from the Wing in three ways:
Set up Gmail as a POP3 account
Automatically forward Gmail
Access Gmail from the Internet
Set up Gmail as a POP3 Account
1. Log in to your Gmail account from your PC.
2. Select Settings at the top of any Gmail page.
3. Select the Forwarding and POP tab in the orange Mail Settings box.
4. Under POP Download, choose to Enable POP for all mail or Enable POP only for mail that arrives from now on.
5. Specify whether you want Gmail to keep a copy of messages in the Inbox when you access messages through POP.
6. Select Save Changes.
I. Auto-configure Gmail from your Pocket PC phone
1. Press Start --> Messaging.
2. Select New Email Account.
3. Enter your e-mail address and make sure the box is checked for getting the settings automatically
4. In the Auto configuration screen, wait until the Status changes from Connecting to Completed and then select Next.
5. Enter your name, user name, and password (DO NOT REMOVE the recent: from in front of the username that it automatically provides) and select Next.
6. Ensure Account type is set to POP3 and select Next.
7. Make sure that Incoming Mail is set to pop.gmail.com:995
8. Make sure that Outgoing Mail is set to smtp.gmail.com:465 and select Finish.
9. Select Yes to confirm that you would like to download mail for this new account now.
II. Automatically Forward Gmail to Another Account
1. Log in to your Gmail account from your PC.
2. Select Settings at the top of any Gmail page
3. Select Forwarding and POP in the orange Mail Settings box.
4. Select Forward a copy of incoming mail and enter the e-mail address to which you'd like your e-mail forwarded.
Now your Gmail will automatically be forwarded to this account.
III. Access Gmail from the Internet
If you don't subscribe to an unlimited data plan or need only occasional access to your Gmail account you may prefer to access your Gmail from your Pocket PC phone using Internet Explorer. To access your account through Internet Explorer, go to http://m.gmail.com.
Part 3 Touch it 2.3 for th wing
The Following is from itje
Original thread http://forum.xda-developers.com/showthread.php?t=340403
Touch it: a rebuilt rom for the wing
Part 3a Touch it Full and Lite
The Following is from itje
Original http://forum.xda-developers.com/showthread.php?t=332789&highlight=wing
Part 4 : Random Stuff
Wing as a Webcam
Found at XDA
http://forum.xda-developers.com/showthread.php?t=348187&highlight=WING+AS+A+WEBCAM
Part 5: T-Mo Wing RUU for USA!!
From xavier6303
Found http://forum.xda-developers.com/showthread.php?t=321717
This will reset your phone, basically reinstall windows and all the phone, heard it works as a decent unbricker,
How to enter boot mode
Restart the phone and hold the voice and camera button
Related
i went to my isp to set gprs and all messaging settings
but remarked that i have no access to set my mms settings or has some
menu item missing ......................
i have qtek2020i , has anyone found such a problem , my device is new........
RE:MMS
Which mobile operator do you use?
go mobile malta ......................
i had to set as my profile isp as vodafone when i registered because the other isp which i personally use was not available during the registation proceedure
MY rom version is 1.11.00WWE
ROM DATE 1/27/05
RADIO VERSION 1.02.00
This may help.
1.
Internet over GPRS settings for your Qtek 2020i
Tap Start - Settings - Connections
Select Add a new modem connection from My ISP
Connection name: go online
Select a mode: Cellular Line GPRS
Select Next
Access point name : gosurfing (contract users)
rtgsurfing (prepaid users)
Leave user name, password and domain blank
Tap on Advanced
Set server-assigned IP address only
Tap on Servers
Set Use server-assigned addresses
Tap on OK
Tap on Finish
Tap on OK and go back to Main screen
To connect, tap on G symbol in the main screen and select Connect GPRS
Upon connection, open Internet Explorer and enter web page address
2.
MMS over GPRS settings for your Qtek 2020i
Tap Start - Settings - tap on Connections tab
Tap on Connections icon
Select Add a new modem connection from the My Work Network list
Enter go mobile mms as connection name
Select Cellular Line (GPRS) as a modem
Tap Next
Access point name : gomms (contract users)
rtgmms ( prepaid users)
Tap Next
Username : mmsuser
Password : mms
Leave domain blank and tap Finish
Close all open windows
Tap Start - Messaging
Tap on Tools on bottom of screen and select MMS Settings
Set Connect via: and choose My Work Network
Tick Retrieve messages immediately
Set 3 in Attempts before giving up
Set Photo resolution to VGA (640x480)
Tap the Servers tab
Tap New
Server Name : go mobile
Gateway : 010.020.020.129
Port number : 9201
Server address : http://mmsc
Sending size limitation : 100K
Tap OK
Select go mobile and tap Set as default
Tap OK to go back to the Messaging page.
To start sending mms, tap on Inbox and select the mms queue from the dropdown list
the problem is when i press tools {in part 2} to set mms messaging i do not have
MMS settings in my menu..................
i think that my new phone lacks mms menu or rom software ,
infact i have no means of sending pictures through mms , i can only send through email, bltouth, infrared , text messages but not through mms...............
RE:MMS Software
I have located the MMS cab install from an Alpine extended ROM. Copy to QTEK and tap to run, you may have to do a soft reset when finished. This should install all the MMS software. Let me know if it works
It is located on the ftp://ftp.xda-developers.com user = xda p/w xda
This is were the file is located. /Alpine/Extended Roms/WWE-Roms/WWE 1.11.112/CAB-MMS20020-Alpine-ENU-21DEC04.CAB
here is the link with password included just click
ftp://xda:[email protected]
i tried to join the petition but after filling the petition , and submittedall..........
came an other screen to verify something i can't understand!!!!!
i thought they wanted to sell something or what?
however i wish ihad 2005 on my device................... :lol:
you are a great person it finally worked and i was able to set my mms account avoiding of having to go back to the shop on monday........
Hi, I'm really pleased it worked.
Although I would question the shop you bought it from, if I were you, as this should have been installed as standard with your qtek, along with a few other bits. :?: I know this because my friend has a QTEK 2020i.
All The Best
DAz.
Concerning the WM2005 Petition, I believe that once you have done the first screen, your details are entered, I ignored the adverts myself.
Hi again,
I just thought, another thing you could try is a 'cold reset' This will reset the qtek, to factory settings (out of the box). If there is no problem with your extended ROM (has all the qtek programs), then MMS etc should install.
**Note** Please read the 'Important' section before you carry out the cold reset.
1. Cold reset by holding your power button down and pushing the soft reset at the same time. Your qtek will then reboot.
2. Once re-booted it will go into the standard screen setup. After this the programs from your extended rom will start to install, your screenlight may turn off at this stage, just tap power button to turn back on, you will see quite a few automatic installations, let these finish at the end you qtek will reboot and all should be installed, including your MMS.
3. If MMS etc are still not installed then reuse the MMS file you downloaded temporarily then I would return to the shop for repair or replacement.
*Important*
Things to do before cold reset
a. Copy anything you want saved to your computer.
b. Go to 'settings/system/permanent save, on your qtek. Tick the boxes to permanently save the information. (these will be saved when you cold reset)
Things to do after cold reset
a. You will have to re-install any programs you have previously installed.
b. Don't forget to re-install the apps that came with your qtek cd.
c. Go to 'settings/system/permanent save, on your qtek and tick the boxes that you want restored.
I have tried to mess with these to turn off Auto on feature in Active Sync, as this causes it to be permanently on, but no luck. In any event, there is some pretty useful info and I am sure someone will be able to come up with some good tweaks here?
http://msdn.microsoft.com/library/d...user5/html/wce50condeviceregistrysettings.asp
All ActiveSync device-related subkeys and values are stored under the HKEY_LOCAL_MACHINE\Software\Microsoft\Windows CE Services registry key on the Windows CE-based device.
The following table shows the values for the HKEY_LOCAL_MACHINE\Software\Microsoft\Windows CE Services registry key.
Note The default registry values vary depending on which Catalog items are included in your OS design. For more information, see Default Registry Settings.
Value : type Description
Version : REG_DWORD Default setting is 20000. Specifies the software version number.
NoSubFolderIn : REG_SZ Default setting is "\My Documents", which is LOC_NOSUBFOLDERIN in datasync.str. Specifies the only synchronizable folder where the user is allowed to create subfolders.
FileSyncPath : REG_SZ Default setting is "\My Documents", which is LOC_FILESYNCPATH in datasync.str.
Specifies the folder to be synchronized during file synchronization.
DefaultNpwNoServer : REG_DWORD This value is not present by default. Creating this value and setting it to 1 will cause the Exchange Server sync selection in the New Partnership Wizard to be unchecked. Users can still select this option, but it will not be selected by default. Setting this value is recommended as most users will want to syncronize with their desktop rather than a server.
Synchronizable Objects Registry Settings
All synchronizable objects are stored under the HKEY_LOCAL_MACHINE\Windows CE Services\Synchronization\Objects subkey on the target device.
The following table shows the values for the HKEY_LOCAL_MACHINE\Windows CE Services\Synchronization\Objects subkey.
Note that registry settings for Contacts, Appointment, and Tasks cannot be disabled.
Value : type Description
File\Store : REG_SZ Default setting is Cefobj.dll. Specifies the name of the File ActiveSync service provider.
Contact\Store : REG_SZ Default setting is Pegobj.dll . Specifies the name of the Contact ActiveSync service provider.
Appointment\Store : REG_SZ Default setting is Pegobj.dll. Specifies the name of the Appointment ActiveSync service provider.
Task\Store : REG_SZ Default setting is Pegobj.dll. Specifies the name of the Task ActiveSync service provider.
Inbox\Store : REG_SZ Default setting is Pegobj.dll. Specifies the name of the String ActiveSync service provider.
Connectivity Registry Settings
The registry settings related to ActiveSync connectivity are stored under the HKEY_CURRENT_USER\ControlPanel\Comm registry key on the target device.
The following table lists the registry values for the HKEY_CURRENT_USER\ControlPanel\Comm registry key.
Value : type Description
AutoCnct : DWORD Default setting is 1 (on). This value turns Autoconnect on and off.
Cnct : REG_SZ Specifies the default connection used when the device is cradled. If this value is not set, the user must select a connection to use when cradling a device.
This string must be prefixed with a backquote (`) for the connection to appear in the ActiveSync user interface.
Note Only RAS entries prefixed with a backquote will appear in the ActiveSync user interface. See Phone-Book Entries for details.
See Also
ActiveSync Registry Settings
Hello folks and friends
does somebody know, what the original o2 cabs realy do?
At the moment my mini s runs without any extendet rom cabs,
but maybe i lose some good things. Maybe someone can tell
me/us what they mean.
Thanks
CAB-Customization-O2DE-Wizard-01-05-28Oct05XML.CAB
=
CAB-Shortcut-MMS-JAVA5XX-VOICE-O2-01Nov05.CAB
=
PhoneLight_Skin_O2_GER_0913.CAB
= Phoneskin
Ringtone_GER_0728_signed.CAB
=
Signed_Disable_SuspendResume.sa.CAB
=
Signed_O2_TSK.sa.CAB
= Windows Skin
Signed_O2DE_Connection_ProxyFix.sa.CAB
=
Signed_O2DE_Connection_Wiz10304102.sa.CAB
=
Signed_O2DE_GPRS_ManualAttach_AutoDetach.sa.CAB
=
Signed_SMS_NoUnicode.sa.CAB
=
Signed_Version.sa.CAB
=
SmartDialing_enable_0915_signed.CAB
=
I worked some out the other day and after searching etc I've come up with this. Some of it was already in the wiki or on other sites...
\CAB-Shortcut-MMS10JAVA5XX-VOICE-O2-31Oct05.CAB
Installs MMS support for Pocket Outlook (folders etc), as well as MIDLet Manager and Voice Dialling
SmartDialing_enable_0915_signed.CAB
Installs smart dialling - works like predictive text when you type a name from your contacts into the phone dialler - same as on Phone Edition.
Signed_O2UK_103040101_RingTone.sa.cab
I think this adds some extra ringtones
Signed_O2UK_exception.sa.CAB
Not sure.. Installed this but didn't notice any difference
Signed_O2UK_Region_Customize.sa.CAB
Could be configure the regional settings of the phone, i.e. language, currency, date and time format, that kind of thing. This would set up the phone for people in the UK without them having to do it themselves.
Signed_Remove_BatteryIcon.sa.CAB
Removes default battery icon from the system tray.
Signed_WIZ_O2UK_PIE_homepage.sa.CAB
Sets the default Pocket IE homepage to something (probably an O2 page). Not useful.
Signed_DiscoButton_16.sa.CAB
Not sure, possibly sets/controls the behaviour of the branded top-right button.
STK_Service.sa.CAB
\CAB-Customisation-O2UK-Wizard-01-05-05Oct05XML.CAB
Probably installs and selects the O2 theme, colour scheme, etc.
PhoneLight_Skin_O2_WWE_1005.CAB
Keypad skin? Possibly. Makes your phone keyboard o2 style... I personally kept the WM2005 one
Signed_UA.sa.CAB
Not sure
Rilgsm_STK.sa.CAB
Has 'gsm' in it, could be important.
Signed_Version.sa.CAB
Not sure
signed_Prodigy_o2AUI4_build26.cab
This is the o2 interface install.. whre you select basic, corp or personal
Also has gprs config
puts task manager back, o2 logo on top bar and o2 icons in programs
and all o2 crap!! Better to install MMS stuff and GPRS settings manually.
To get GPRS and MMS to work you also have to put these settings in, they are an adaption of some found on these fourms and other sites because people's instructions weren't as clear and I couldn't get them working. I then did a hard reset and copied down the settings with all the o2 crap installed and then did a proper hard reset:
GPRS Web settings
Start > Settings > Connections > Connections > Under My ISP tap Manage Existing Connections and then Tap Edit (if this isn't present then tap 'Add a new modem connection') The Select a Modem drop-down box should be set to Cellular Line (GPRS), Connection name: Mobile Web, Tap Next Access Point Name: mobile.o2.co.uk Tap Next Username:O2web (capital O, not a zero)
Password: password
Domain: leave blank
Tap Advanced
On the TCP/IP tab, only Use Server-assigned IP Address should be selected Tap the Servers tab Use Specific Server Addresses should be selected
DNS: 193.113.200.200
Alt DNS: 193.113.200.201
Tap OK
Tap Finish
GPRS WAP settings
Start > Settings > Connections > Connections > Under My Work Network tap Manage Existing Connections and then Tap Edit (if this isn't present then tap 'Add a new modem connection'), Connection name 'O2 Active', The Select a Modem drop-down box should be set to Cellular Line (GPRS) Tap Next Access Point Name: wap.o2.co.uk (for Prepay enter payandgo.o2.co.uk) Tap Next Username2wap (lowercase o this time! not zero) (for Prepay enter payandgo)
Password: password
Domain: leave blank
Tap Advanced
On the TCP/IP tab, only Use Server-assigned IP Address should be selected Tap the Servers tab Only Use Server-assigned Address should be selected Tap OK Tap Finish Tap Proxy Settings Tap Advanced In the WAP field enter 193.113.200.195 In the field to the right of this enter 9201 Tap OK and exit
MMS settings
Start > Messaging > Tools > MMS Settings Connect Via: My Work Network (this links to the GPRS WAP settings) Tick Retrieve Messages Immediately Tick OK to download when roaming Tick Save sent messages Attempes before give up: 3 Photo Resolution: Original Tap the Servers tab Tap O2UK Server Name: O2UK
Gateway: 193.113.200.195
Port Number: 9201
Server Address: http://mmsc.mms.o2.co.uk:8002 Sending Size Limitations: 100K Tap OK twice to exit
Make sure you have wap version 1.2 selected in MMS settings!!
MMS and GPRS work fine now.
thanks !
Battery Icon
I wonder why O2 decided to remove the battery icon from the system tray.
Having just changed from an SE P900 to XDA Mini S, I really miss the battery icon and would like to know how to get it back.
Get back the battery icon
Whops forgot the link! see below
Get back the battery icon
Hi
try looking here [ http://forum.xda-developers.com/viewtopic.php?p=234919 ] and downloading the SHOWBATTERY hack
Alternatively, a better icon is available in spb pocket plus and o2 plus...
Dip
Battery Icon
That's great - many thanks
Guess who did not backup his O2 ROM, can anyone post the original cabs so i can re-enable predictive dialing etc?
_______________________________________
Having Hard Reset my T-Mobile MDA Vario II and installed needed software applications I became challenged.
When Bluetooth pairing my Holux GPSlim236 GPS Receiver I was unable to select the needed communications port COM4
On my PDAs I have installed the Registry editor “PHM RegEdit”.
When I looked at my MDA Vario II Registry all GPS Settings was blank
Here I document and share the Registry and Device settings from scratch that resulted in my device pairing and Satellite Navigation working properly using TomTom Navigator v6.
1. Registry GPS Intermediate Settings
Select PHM RegEdit, or the editor that is your preference, and
Select HKEY_LOCAL MACHINE, select System,
Select CurrentControlSet, and Select GPS Intermediate Driver,
Saving repetition when prompted select OK
Select the Key name “Drivers” if it does not exists
Select “Edit”, New Key and type Drivers
Select Drivers and “Edit” and select New String Value
Value name: Currentdriver and
Value data: Control Panel Configured Device
Select Drivers and “Edit” and
Select New Key and type Control Panel Configured Device
Select Control Panel Configured Device
Select “Edit” and select New DWORD Value
Value name: Baud and Value data: 4800
Select Drivers and “Edit” and select New String Value
Value name: CommPort and Value data: COM4
Select Drivers and “Edit” and select New String Value
Value name: InterfaceType and Value data: COMM
Select Multiplexor and “Edit” and select New String Value
Value name: DriverInterface and Value data: COM5
2. Registry GPS Settings
Open HKEY_LOCAL MACHINE, select Control Panel
Select GPS Settings
Select “Edit” and select New DWORD Value
Value name: Group and Value data: 2
Select “Edit” and select New DWORD Value
Value name: Hide and Value data: 0 (that is value zero)
Exit Editor and Soft Reset Device
3. Device Connection Settings
Select Start, Settings, Connections and GPS Settings
Select GPS program port: COM5
Select GPS Hardware port: COM4 and select a Baud rate: 4800
Select Access and check box Manage GPS automatically (recommended)
4. Device Bluetooth and GPS Receiver Settings
Select Comm Manager and ensure Bluetooth is turned ON
Select Bluetooth Settings and COM Ports
Select and hold Holux GPSlim236, select “Edit”
Select Bluetooth Port: COM4 and select Finish and OK
5. TomTom Navigator software and GPS Receiver Settings
Start TomTom Navigator v6
Select Change preferences, Show GPS status, Configure
Select Other Bluetooth GPS receiver and select
Select GPS is connected to: COM4 and select done
Another intellectual challenge put to bed
PS I can confirm that settings documented here perform satisfactory on WM5 and WM6 device
watchdog2003 said:
_______________________________________
Another intellectual challenge put to bed
Click to expand...
Click to collapse
ummmm...here's the pat on your back you were looking for
*pat*
I'm sure someone may find this helpful though...and I'm sure that's why you posted this.
For sure.
Hi *.
I have data connection called "Internet". Selected as default in Settings -> Connections -> Advanced -> Select Network and disabled with Enabled = 0 registry key. When I want to use it, I just change to Enabled = 1. Simple and fast.
But after I'm done with checking emails, disconnect "Internet" and change back to Enabled = 0, Windows still "remembers" that this connection is usable and ignores registry. I have to soft-reset to make it "forget".
Is there any way to avoid this?
You need to do a soft reset after registry changes to fully save the change.
If you don't want the data line to stay on then don't make that registry change. When you select "Send/Receive" in Outlook the data line will come on automatically. You can also turn the data line on by launching Internet Explorer.
That regsitry key is really for people who want the data line to stay on all the time.