Related
Hello
I am stucked in BootLoader mode.
problems:
if i turn on the phone, nothing happens
if i reset the phone, nothing happens
if i hardreset the phone, greean and black sceen with ipl spl numbers.
if i take out the battery, nothing happens..
if i run the original htc wm6 setup or wm5 setup, it makes an error 300, invalid rom update utility.
i only can turn my phone to bootloader mode.
the RUU runs until i push "update" button, and then error 300!
please help me!
thank you
pulyka
ps:
htc wizard has "ROMUpdateUtility_Wizard_NoID.exe"
that is for this problem, i think.
google did not matched in herald like this
you ARE trying to RUU with a HERALD ruu, no?
Also, if you have a wing or a dopod, you must ruu with the tmobile or dopod variation of the RUU, respectively.
i have HTC herald (not wing or etc) black skin with grey buttons.
i tryed to flash with official wm6 ftom htc.com, and the official wm5, from the net (i dont know the source: RUU_Herald_HTC_WWE_1.8.405.1_02.71.90_Ship.exe)
but, the error is the same: 300, invalid update tool.
my friend sais: my bootloader damaged.
i must get an SD Dump from a HTC herald, same as this device, and then i have a glimmer of hope..
or service repair:|
tmo ruu didnot worked also..
regards
pulyka
try mtty
set 16 0
or set 14 0, I forget which, try both
then do
task 8
Olipro said:
try mtty
set 16 0
or set 14 0, I forget which, try both
then do
task 8
Click to expand...
Click to collapse
I also got one with error 300
I try set 16 0 and set 14 0 both
then task 8,give me
Invalid command : task 8
For a help screen, use command ? or h
....how?
pulyka said:
Hello
I am stucked in BootLoader mode.
problems:
if i turn on the phone, nothing happens
if i reset the phone, nothing happens
if i hardreset the phone, greean and black sceen with ipl spl numbers.
if i take out the battery, nothing happens..
if i run the original htc wm6 setup or wm5 setup, it makes an error 300, invalid rom update utility.
i only can turn my phone to bootloader mode.
the RUU runs until i push "update" button, and then error 300!
please help me!
thank you
pulyka
ps:
htc wizard has "ROMUpdateUtility_Wizard_NoID.exe"
that is for this problem, i think.
google did not matched in herald like this
Click to expand...
Click to collapse
Help me,I like you
hponline said:
Help me,I like you
Click to expand...
Click to collapse
Hypercore's ROM kitchens has the Herald RUU upgrader... I wonder if that would work...
pulyka said:
Hello
I am stucked in BootLoader mode.
problems:
if i turn on the phone, nothing happens
if i reset the phone, nothing happens
if i hardreset the phone, greean and black sceen with ipl spl numbers.
if i take out the battery, nothing happens..
if i run the original htc wm6 setup or wm5 setup, it makes an error 300, invalid rom update utility.
i only can turn my phone to bootloader mode.
the RUU runs until i push "update" button, and then error 300!
please help me!
thank you
pulyka
ps:
htc wizard has "ROMUpdateUtility_Wizard_NoID.exe"
that is for this problem, i think.
google did not matched in herald like this
Click to expand...
Click to collapse
I also have the same probem.. after using HERALD-USPL-beta3
beucase I want to change langauge GERMANY to ENGLISH.
PHONE IS HTC HERA100
and having same problem as ABOVE.
NEED SOLUTION.. any comment is will be appreciated
Br.
What is your IPL and SPL in bootloader?
Where did you buy your herald?
oddball1 said:
What is your IPL and SPL in bootloader?
Where did you buy your herald?
Click to expand...
Click to collapse
Its not mine phone.. Its from my Customer he bring phone to me for change language.
before I don't checked IPL / SPL
but after using HERALD-USPL-beta3
NOW IPL IS 1.08.0001 and SPL IS 1.08.0001 is also same.
waiting for the solution..
Br.
DrMobile said:
Its not mine phone.. Its from my Customer he bring phone to me for change language.
before I don't checked IPL / SPL
but after using HERALD-USPL-beta3
NOW IPL IS 1.08.0001 and SPL IS 1.08.0001 is also same.
waiting for the solution..
Br.
Click to expand...
Click to collapse
hello!
Have you ever solved your problem? If yes maybe you can share!!!!!
Or any solution for this yet? Please I need help.
Br
keke
I have HTC ELF 0300 that freezes on the T-mobile logo when i try to power on!!!
I tried with hard reset,but that not helped.
I can't make ActiveSync connection with my PC!
I try with connecting the phone in bootloader mode,but still can't make ActiveSync comunication!
Any advice???
Did you manage to see a screen that says 'smart mobility'
jeremy89632 said:
Did you manage to see a screen that says 'smart mobility'
Click to expand...
Click to collapse
No! It just goes to operator logo and blocks on it!
When you are in bootloader mode.
Does windows xp or vista detect that?
Activesync ONLY LOADS in normal mode, not bootloader.
jeremy89632 said:
When you are in bootloader mode.
Does windows xp or vista detect that?
Activesync ONLY LOADS in normal mode, not bootloader.
Click to expand...
Click to collapse
No,windows doesn't detect the phone in bootloader mode!
Weird.
My vista pc will.
But have to install Windows Mobile Device Centre first.
When I connect in bootloader mode I tried with many Rom updaters but every time I get this message 'The update utility can not be used with your PDA Phone.Please get newer update utility'
I tried with update utility 3.27.4.3 an lower versions.
Is there newer version?
What is your phone's IPL and SPL?
Before you start your phone, press the power and camera key together, it will boot up a multi colour-ed screen and it will report the IPL and SPL to you there
jeremy89632 said:
What is your phone's IPL and SPL?
Before you start your phone, press the power and camera key together, it will boot up a multi colour-ed screen and it will report the IPL and SPL to you there
Click to expand...
Click to collapse
IPL 1.13.0002
SPL 1.13.0000
any idea what to try next???
thanx for your help bro anyway!
Can you sync your htc to other pc's?
Reinstall activesync.
and your ipl and spl is way too old.
During the meantime, read the other threads.
Will be going to camp in 14 hrs time and its almost 1am here.
So yeah.
I've tried to sunc with other PC's too,but the same result! when i start some Rom Update Utility it gives me that I should try with newer version.
well, if that can detect the newer version!
Bingo!
you computer can read it.
Alright, update your IPL and SPL to 3.10.
and its avail at htc upgrading forum.
HTC ELF 0300 Error
Hello somebody could help the other day I came across a ELF0300 phone and also the problem that would crash the machine operator in the Logo.
inquired the previous administrator of the system can not be installed on it.
handheld device is excellent by the way the externally,and we need to somehow fix
Bootloader mode writes
IPL 2.26.0002
SPL 2.26.0000
but quite interesting if you install this dream running 100% and then upgrade error
Activesync does not do anything
Thanks in advance for the help
Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual
Hi everyone...
I've tried to cid unlock my artemis but I wasn't able to do it...
any clues?
When I trie to install a rom (oficial Portuguese 3.14) it gives me Invalid vendor ID...
What could I been doing wrong?
Thanks in advance!
i had trouble cid unlocking my artemis, i dont know what i did but i done it, this is what i did tho.lol
download Uspl - mine came with these cab files so i installed them on the phone.
''Cert_SPCS''
''EnableRapi''
link to pc and get active sync connection.
run ''start_uspl'' (on pc which opens a dos screen)
phone screen will go off into white or black screen.
(should see a penguin)
after that ''ROMUpdateUtility'' will automaticy start.
*cant remember if you need soft reset or not - think you do so active sync is enabled again, try with and without soft reset!
click through untill it starts to update, your phone will go into bootloader mode showing a usb connection. it will automaticly go into a gray screen with a loading bar.
SPL;1.11.0000 should now be displayed at boot
if this does not work try hard reset on phone and reinstall active sync on pc.
use uspl cmon to flash any rom..
spl 1.11.cmon