I restore de the original OS of the PDA and when appears on the screen to do the align the screen I tap the screen but the test doesn't comes to a end and I can't use the PDA.
What's can be the problem and how can I solve it?
it hapeend to me too
than i opend it and unplug the screen flat cable and replug it again and it work
tray
Related
Yhea! i'm here for the second time asking something about the digitizer. Now the problem is:
I've the digitizer disconnected and i've experienced (last time) that part of the front buttons don't work. Not important.. they're well replicated except for the red phone but it's another problem. I've jet ordered and payed a new digitizer and i'm waiting for it. The real problem is that now i can't use my phone because ita was going all well (without buttons) but modifying the start plugin by the schap's registry editor my vpa freeze on the splash screen. I've made a hard-reset and (as indicated somewhere) with the pone stopped on the screen "tap enywhere to start your wm bla bla bla" i've connected it via usb and deleted the link "c:\windows\autostart\welcome.ink" or something similar. I've bypassed the welcome procedure but now after boot my wm freeze with a strange screen situation.. i can see the top bar but the rest of the screen is occuped by the splash screen.. like it'is without screen refresh.
Is it possible that the welcome.exe adding useful information to registry that let the phone working well? May I insert them by hand with an editor launched on my pc with the pda connected? or my tytn is definitively gone?
The phone does not respond to any button except the power button (for standby and power off with the message window fully represented) and the button on the left that (if hold) start the recording note software as shap's default.
Tell me what you think and thank you!
Gianmarco
Hi,
on my xda exec O2 I have installed the ROM Vodafone italy and everything he has gone ok.
When I have installed the patch for the extended memory I have begun to have problems.
The device thick freeza and it suffers blocks, Therefore I have decided to again install the ROM, but during to calibrate the screen it doesn't go anymore before.
It continues to for some then it jams.
I have tried to install other ROM, the Qtek but from the same problem.
Do you advise to use MTTY?
TiA
If so, remove it and test the response from the Touch Screen.
Screen protectors can interfere with the sensitivity and accuracy of the Touch Screen.
Attempt to re-align the screen by going to Start>Settings>System Tab>Screen and then tap on Align Screen or press and hold the Center Navigation key and then press the Internet Explorer Button. Note: To ensure accuracy, Screen Alignment must be completed using the device Stylus and no other object
The touch screen on a friend of mine's MDA stopped working in the middle and had lost it's alignment making the device hard to use. So I picked up an oem LCD assembly and replaced it. Now no matter how many times I try to align the screen it just keeps cycling. It responds to the taps and goes full cycle but just goes back to the begining. I have search everwhere to find a solution. I have done it in portrait and landscape I have hard reset it and upgraded the rom but still have the same problem. Any Ideas?
Did you try the way yet where you must put a dummy file named welcome.??? (cant recall the extension) in the root of youre phone?
EDIT: make a textfile and make sure extensions are visible and renamle the WHOLE name (including .txt) to welcome.not in the root of youre phone, then restart it and normally voila
I was able to get past the alignment screen but am unable to align it. It just keeps cycling as I press the markers. The touch screen is way out of alignment.
i d that before and i did a hard reset.
in my rom came de alignment after a soft reset so deleted it with startup manager
I was able to get past the screen by deleting the welcome.lnk with pocket controller. My beggest problem is that I can't calibrate the screen in order to make the touch screen usable. I do not know what the problem is. The screen responds when I touch the marker and goes through the cycle but never stops. I have tried going through it as much as 30 times portrait and landscape and it will not accept the alignment.
My problem is that my screen is still working even if I press the turnoff button and I set turnoff the lighting after 1 min. . I did a format for my cell phone and I changed the room but it is still the same but I found a solution where if I connect my cell phone with the cable USB( either computer’s cable or car’s cable), the screen turn off but as soon as I remove the USB, it doesn’t let me tur
After doing a hard reset on my perfectly-functioning Pro the other day, the screen and buttons have now stopped working. My question is two-fold:
1. What the heck is going on?
The phone worked fine until I did the hard reset. Now, when I do a hard reset, everything appears to work correctly through the screen-alignment. The screen responds properly at that stage. Immediately afterward, the normal Today screen pops up for a split second. After that, the "Treo Customization" screen comes up, and that's where it all goes to hell. After the "Treo Customization" runs its course, the phone says "tap screen to reset." After tapping the screen, the phone responds and resets itself.
After that, a blank today screen appears. The tool bar on top is there and the background is there, but that's it. The screen and buttons are unresponsive except to brighten the screen after it periodically dims. Several other functions continue to work. I can activate wifi via the side button. The top button turns off the screen. Strangely enough, the QWERTY keyboard is completely unresponsive, except that the search button works (alt button and magnifying glass).
Does this sound like a hardware problem? Could it be fixed with a flash and new rom?
2. I tried to flash the phone and install a new rom to see if that would help, but I was unsuccessful for the following reasons: 1) When I run PANTHER_CDMA_HSPL_V101, the bootloader screen appears, but immediately upon that occurring, my sync connection disappears, so I can't proceed through my computer. 2) I can't run the manual flash program (SSPL-Manual-PantherCDMA) because I have no functioning controls on the phone itself.
Any ideas? Is there any way to achieve a flash on an unresponsive phone, or should I start shopping?
Thanks!
Mark Pemberton