Related
I have had this happen twice now.
My tytn (v0628) has locked up. I took it out of my case and pressed the power button and got nothing. The lights are blinking as usual (bluetooth and phone). I tried to call it and it did not wake or ring, but on the phone I was calling on it was ringing, and I got that speaker interference so I know the call was reaching my TYTN, but it didn't wake up. So I had to soft reset it. The first time this happened it was on the charger (wall) and not in its case, it happened overnight. Woke up to it not turning on.
Anyone else having this issue?
Later; Lew
Yup ... I've seen it perhaps 6 or 7 times in the month I've had it.
The actual stability issues I had were resolved - i.e. hanging soft resets etc - by rebuilding. In the main it is very stable.
You also get irritating hangs when the device is left to rung and hang up.
Paul.
Yep. Same issue here. The phone is working normally; you just couldn't get it out of powersave mode by pressing the on/off button. I sent mine back for replacement due to two bad keys and an inoperative flash, but I was going to investigate it further. Like:
How about pressing something that would normally wake it up like the camera button perhaps?
... sometimes its rough out here on the (b)leading edge....
This happened twice to me too, both times after being charging for 4-5 hours during the night it doesn't wake up the next morning, it doesn't matter which key I press, only solution was to soft-reset with stylus.
lewcamino said:
My tytn (v0628) has locked up.
Click to expand...
Click to collapse
Mine has also HT628 S/N.
lewcamino said:
I took it out of my case and pressed the power button and got nothing. The lights are blinking as usual (bluetooth and phone).
Click to expand...
Click to collapse
Same here, but bluetooth was turned off. Only phone blinking.
lewcamino said:
I tried to call it and it did not wake or ring, but on the phone I was calling on it was ringing, and I got that speaker interference so I know the call was reaching my TYTN, but it didn't wake up.
Click to expand...
Click to collapse
Exactly the same issue here, I could hear the interfernce on my hi-fi speakers when I called from landline phone to my cell number.
lewcamino said:
So I had to soft reset it. The first time this happened it was on the charger (wall) and not in its case, it happened overnight. Woke up to it not turning on.
Click to expand...
Click to collapse
I didn't have it on the wall charger, but using the USB computer cable, so it doesn't seem a problem related to charger.
I had this happen to me a bunch of times too but it turns out that it was spb software that was causing this issue for me. I had SPB pocket plus and Weather installed, and running on my today screen and it happened quite frequently. I decided to do a hard reset and keep the software minimal to what i "needed" so I kept is simple. haven't had this problem since then. I believer it has to do with the today screen which is either a bug in spb software of a bug in the firmware.
Good Luck!
yak86 said:
it was spb software that was causing this issue for me.
Click to expand...
Click to collapse
I don't have any 3rd party software from SPB installed, but can be probably some other soft....
It was locking up for me too and I went and removed SBSH PocketWeather to test it out since it was the last thing I installed. I remove it from teh Today screen and have not had a lock up yet. I am also running SPB Diary with no problems. I am thinking it could possibly be due to these programs that have to connect to GPRS/UDMA every so often to update its data like PocketWeather since it happens with different programs. Maybe it locks up while charging and trying to make a connection. Just my thoughts.
AJH..
hmmm... I also had spb pocket plus and spb weather installed. When I get my next TyTN I'll have to remove those if the problem re-occurs. however I also had one instance of POFs charge related issue. Maybe its also spb backup related since I fire one of those off every day at 3AM.
I don't have any SPB software on mine. However I was using magic button with the battery meter on top. I have disabled the battery meter. That was 3 days ago. It has not happened since but that does not mean it was the problem. BTW I decided to allow the device to stay on (screen back light off but awake) while charging to prevent this from happening overnight.
I know SPB has a battery meter and I also know that this device reports the battery level in strange ways. Like it only reports 10% increments. Also when you first wake it up the battery is @ 100% then goes to the proper level.
Try this if you have voice command;
Have your device off the charger with some battery missing, 90% or lower. Wake up your phone and quickly activate voice command and say "what is my battery level" It will report something strange like "the battery level is unavailable" or I got this one "the battery level is critical" but it was @ 50% and when i asked again it reported 50% just fine. So I think this may be related to battery polling programs.
I am guessing at this and I have not had long enough time to test it but I thought I would toss it out there for everyone to try.
Later; Lew
I have the SAME EXACTLY problem with my magician, this is a common fault as I can see :? The fact is, most users says that the PDA wouldn't wake up after a night: then the problem is the low temperature.. test this putting the TyTN in a fridge while it's cold, then try to wake it up the problem is there...
MocciJ
i had the same problem with my trion using imate rom......but it didnt happen after a long charge......i just havent turned it on for about 5-7 hours, and then when i did turn it on it wont respond.....so i had to do a soft reset........from my experience i think it was my wisbar advance so i uninstalled it and went back to using wisbar lite......i never had this problem before when i was running wisbar lite originally....when i installed wisbar advance and had it on my device for a couple of days and thats when the problem started to happen......after uninstalling wisbar advance and putting back the wisbar lite the problem didnt come back.....so i think it has something to do with what is running on our today screen.....maybe programs that takes up a lot of resources etc might be the culprit......
i have same problems with prophet. after every charging a have to soft-reset. no additional software is installed and never been. just clenan WM5. so this is not a problem with 3rd party software.
Has anyone noticed that the magnet in the HTC leather case is too strong for the TyTN?
I think that I FINALLY figured out why I was having so many "strange" things happen (i.e. Pull out the phone from the HTC case and it comes out in landscape mode). To test- Open the case and move the magnetic flap around the phone while it's on (with screen lit up) and see if it causes a problem with the display.
I need to find a durable NON-Magnetic carry case. Any know of one available for the TyTN?
ktwildchild said:
(i.e. Pull out the phone from the HTC case and it comes out in landscape mode)
Click to expand...
Click to collapse
sure u're posting in the right topic?? :wink:
Anyway, I recommend to all who's having this problem to send the TyTN to repairs.. It's an hardware fault :roll:
MocciJ
Well you can send out your TyTN if you want. I can say that since I removed the battery bar feture in magic button I have not had this problem. I also let my device stay on (screen backlight off, but device still on) over night.
Later; Lew
lewcamino said:
I have had this happen twice now.
Anyone else having this issue?
Click to expand...
Click to collapse
Yes. I removed Opera and all went back to normal.
We have many topics on "locking up", freezing, storage card problems, windows media player problem, and so on
Please when you have this kind of problem check if you are using appz writing/reading on the storage card
The worst period in my life with TyTN was when I set IE cache and E-mail cache on storage card... (It is a FAT 16 card...)
http://forum.xda-developers.com/viewtopic.php?t=61879 is about overnight freezing....
Sergiopi,
Can you tell us in simple terms what to check to be sure that our programs are not making use of storage card. For instance, I am using pocketbreeze and sbsh pocketweather and both were installed on storage card. Should I simply remove them from the Today screen? Should I reinstall them on main memory?
Thanks, apap
1) Have you sat up IE or Mail SW to store cache or attachment on storage card?
2) Have appz with auto update or log file installed on storage card?
3) Check active processes and events scheduled
This is a simple check list, you can also leave without storage card your TyTN and check if any error message appear after 2-3 ours
To stop applications use any process explore to recognize and stop the process (safer un-checking from today screen first)
I experienced this problem regularly, especially when left on charger overnight as others have reported . I also chgd my ROM from HTC to IMATE -- experienced lockups in both so it's not the ROM.
Saw a suggested "fix" another thread (referenced above) -- Settings/Connections/PC to USB - uncheck box for Advanced Network Functionality --- that seems to have corrected it! I was experiencing the lockip several times a day, but haven't had a lockup since making this chamge. Amd my software install is very similar to others in this thread - spbpktplus, sbsh pocket weather and pocket breeze, wisbar adv 2.
Not sure how this setting is involved, or even whzt it does, but glad the lockips seem to have endec.
Hi,
Lately the phone side of my T-Mobile Vario II is alays off after I turn it off and then on. I have to manually start it from the Comms Manager.
It was fine when I first got it.
Any ideas? Is there a Registry setting I can check?
Thanks.
Hi,
I have the same problem too. Hope sombody can find a solution to it.
cheers
Make comm manager an exception in whatever task manager (magic button, InClose, ....) you have installed.
I have the same problem and I don't have any of the task managers installed....
Same issue here. It doesn't seem to be related to close app exception lists either since mine only recently started exhibiting this issue and I've had spb pocket plus installed since I upgraded to the 1.31 Cingular ROM with no close exceptions defined. My first TyTN started doing it too.
Interestingly, pressing reset doesn't have the same effect: the radio comes right up then. Every night spb backup plus resets my device after the backup and I've never had an issue. Therefore, I believe it has something to do with the power-off shutdown process itself. In support of this, I've noticed that when I press "Yes" on the shutdown dialog, the first thing that happens is the radio shuts off. Then, about 5 seconds later the device shuts off.
What I've done so far is to add Conmgr.exe to SPB pocket plus' close app exception list. I'll see if this affects anything. IIRC there were a few more apps that needed adding too. I'm hunting those down right now.
edit:
hmmm.... after adding conmgr.exe to the close exception list, the phone came right up when I tried a powercycle. Either this fixes it or its intermittent. Perhaps spb does an explicit close on all open apps when you try to power off and this is somehow affecting the phone mode when conmgr starts back up.
Hi, are you all referring to flight mode being on when the phone reboots?
I know I have had an issue where after I install some apps that when I reboot flight mode will be on, and it will keep doing this, I also noticed that if I just soft reset it wouldn't happen, the trick I have found to get it workin again was to use the always on settings with the fit4cat tweaker, and usually once or a couple times of setting like gprs always on of off, and a softresetting that it will fix the flight mode being on problem...I'm not sure if you all are talkin about the same thing and this really isn't pinpointing the fix, but I thought this info might help atleast one persons aggrivation..cause I'm sure I can't be the only one with the flight mode problem.
I don't use spb btw, well I use spb backup, but have had the problem arise after I installed wmirc and netfront for example.
I never use the comm manager, I just click the signal by the time in the taskbar and it says flight mode is on, I just realized it is likely the same problem.
edit: I had the problem arise again and can't figure out how to fix it, even tried a registry restore.
Not a Fix but a Working Solution
I started having the issue of the radio being off on startup a few weeks ago.
So I invested($10) in a copy of SK Softwares Scheduling Manager SKScheMa.
http://s-k-tools.com/index.html?sksc..._skschema.html
This has a powerful scripting language and one of the script commands is "GPRS on"
I created a shortcut in the startup folder to a GPRS On script. and since then I have had no more problems.
Another workaround (free)
This problem recently started to affect my Cing 8525, as well. I don't know if this has been already resolved, but my solution was to DL this little freebee named FlightMode v1.1.0 (Thanks to Cristiano Severini) from here:
http://www .winmobileapps.com /device/pocketpc/fm/fm .aspx
I've only tested it so far with one reboot, but it seems to work around whatever bug there is in WM5 ... as long as you don't mind CommManager flashing on the screen for an instant at bootup, and then having it running in the background (too bad it doesn't do a full close of CM).
I installed this app, and then created a shortcut and placed it into the \Windows\Startup directory. Seems to do the trick nicely.
Hope you find it useful.
[EDIT: Further tests have shown me that Comm Manager does NOT flash on the screen briefly, nor remain loaded. Seems that had something to do with PhoneAlarm, instead. Personally, I think this might be a good solution to this particular problem.]
[EDIT2: Ok, further tests of Fightmode showed me that this was merely a toggle, and in cases where the phone was ON after a reboot, Flightmode shut it off. Nice little program, but this issue made me look at the SKScheMa mentioned by paulbacik. What a powerful tool! I agree, that $9.60US is a bit expensive just to have the phone/radio on after a reboot, but I feel this app has some wonderful potential. So I plunked down the cash and registered it after a day of testing. Does the trick VERY nicely! Thanks Paul!]
Aha... I think I have found the problem...
Ms Voice Command v1.60 does it for me. As soon as I install it the phone won't start at boot up. Remove it and the problem is gone.
Wonder if everyone else with this problem has VC installed.
Nope ... not VC
Thanks for the attempt, Essef, but VC is one of the few apps I haven't (yet) installed. I'm leaning towards it being related to (in my case) Wi-Fi Compnion. I'm going to reinstall that this weekend, and see if my problem resurfaces. Hopefully not, since I like the app (and paid for it).
FWIW, I am also now using the SK ScheMa "fix", and I like it a lot. It never fails on startup, and I aim to use it ... and PPL a lot to customize/personalize my 8525.
Best regards,
-pvs
[UPDATE] OK, so far, so good. I reinstalled Wi-Fi Companion last night, and it worked pretty well. Actually, my 8525 froze the first time, and I needed to hard-reset (thank GOD for SPB Backup!). But, not being one who gives-up easily, I tried it again, and it installed flawlessly. I've been using it on-and-off today, and so far, my phone still boots without the "The Operation Failed" error messages I was seeing before. Mind you, I have done quite a bit of tinkering since the last time I had the problem, going from ROM version 1.34.502.1 to 2.06.502.3 after SuperCIDing and SIM Unlocking the device, so maybe all of this stuff made a difference.
At any rate, I will post to this thread again should anything change with regard to this issue.
-pvs
[/UPDATE]
After a bit of experimention I found a fix for Voice Command causing this on my Jasjam.
It seemed to occur as soon as I assigned VC to the 5th button (which was Cyberon's Voice Dialer) - then no radio after reboot.
So I tried removing the sddaemon shortcut in the startup folder (this starts the Cyberon service), rebooted then assigned VC to button 5 and now the radio satrts everytime I reboot.
I guess with the Cyberon service running and assigned to button 5, reassigning the button caused the device to get confused and not start the radio.
Hi,
i have everytime the problem that when i turn the ameo off,
it freeze when i turn it on, this is randomly so i cannot figure out
when this is happends, after soft reset it works again.
Is there a way to find out where the gab is?
tried to close every open application so far, and turn the most
used on after turn of the device.
I'll hope to find out otherwise i need to to the hard reset
(it took that serveral hours to install al again .
thanks
tvrman said:
Hi,
i have everytime the problem that when i turn the ameo off,
it freeze when i turn it on, this is randomly so i cannot figure out
when this is happends, after soft reset it works again.
Is there a way to find out where the gab is?
tried to close every open application so far, and turn the most
used on after turn of the device.
I'll hope to find out otherwise i need to to the hard reset
(it took that serveral hours to install al again .
thanks
Click to expand...
Click to collapse
Hi tvrman.
For starters, install Sprite backup (on one of the CD's you got with the Ameo). This will eradicate the need for a full install after a hard reset in the future!
I suggest you do a full hard reset anyway then install Sprite Backup utility.
Only put back your essential apps one by one with 1/2 a days gap between each installation and test the turn off turn on function.
Be sure to use the supplied X-Button application to ensure you properly clode apps down after you're finished with them....or use Wisbar Advance 2, which will do it for you....except for Active Sync (this will always remain active unless shut down manually in memory menu).
I have not once suffered the problem you have in over a months use of the Ameo....might be a faulty unit or a buggy ROM. What version ROM are you using?
Anyway, if all goes well over the next 3 days, do a full backup and save a copy to your storage card or micro drive and be sure to copy a copy over to your PC...that should future peoof you having to do a full install again in the future. And be sure only to back up, if you have no problems with the device and the problems you mentioned earlier. Otherwise you will allways restore the bugs in the device after a hard reset.
Hope this helps. keep us updated on how you get on.
Mackaby007
thanks for you professional answer, i was not aware that spd backup
was on the cd which was delivered at the ameo.
Well yesterday i found out that one of the programs (profimail)
which i'm using serveral times a day for my mail, that this is the problem
I found out that yesterday i didn't use profimail but the built in mail the
whole day and the ameo did not freeze at all the whole day
tried to turn it off an on the whole day and no problems at all,
yesterday late i start profimail and check serveral mails, i close profimail
and turn the device off, later turn it on and a black screen it would not
turn on
After soft reset everthing works.
So i will check today again without using profimail and see what's happends
again.
i'll let you know....
hi,
I had the same problem.
My solution was to format the mini-sd card.
So what i did:
1. copied all data on de minisd in a cardreader to a directory on pc
2. Formatted (not quick) the minisd
3. Copied all data back to the minisd.
All the tests I have tried suggest it is Wisebar Advance 2 that is causing the freezing.
Anyone else find this? Shame as it is the program I like the most
Robert
tvrman said:
Hi,
i have everytime the problem that when i turn the ameo off,
it freeze when i turn it on, this is randomly so i cannot figure out
when this is happends, after soft reset it works again.
Is there a way to find out where the gab is?
tried to close every open application so far, and turn the most
used on after turn of the device.
I'll hope to find out otherwise i need to to the hard reset
(it took that serveral hours to install al again .
thanks
Click to expand...
Click to collapse
Have you got a password to lock your phone try removing that see if it still locks , i was having the same issue
Mrsums said:
All the tests I have tried suggest it is Wisebar Advance 2 that is causing the freezing.
Anyone else find this? Shame as it is the program I like the most
Robert
Click to expand...
Click to collapse
No such issue here! WA2 runs like a dream on my Ameo...even better than it did on my Hermes or Prophet! I'm using the 2.8.0.2 version of WA2 without WAD.
WA2 + WAD
Yes, in my case it was also WA2. I made my own skin and all work fine. But in time I got more lock-ups. So I decided to reinstall everything. Then things went wrong. That day I have installed everything 6 times. Every time I had lock-ups when I pushed the power button and activated it again. But after disabeling WA I had no troubles anymore. The last production and beta version have the same problems. At this point I have to advice not to use WA2. I did not examine every feature of WA2. So there can be one feature that caused the problem. I made my own iPhone landscape skin and I was very pleased. Could somebody try this skin to see if it freezes their device?
skin
iPhone skin ftp://xda:[email protected]/Uploads/Software/iPhone.rar
I use a lot of apps. I also use the following plugins on WAD:
SPB Diary
Profiles for Windows Mobile
Windows Life Messenger
QAN said:
Yes, in my case it was also WA2. I made my own skin and all work fine. But in time I got more lock-ups. So I decided to reinstall everything. Then things went wrong. That day I have installed everything 6 times. Every time I had lock-ups when I pushed the power button and activated it again. But after disabeling WA I had no troubles anymore. The last production and beta version have the same problems. At this point I have to advice not to use WA2. I did not examine every feature of WA2. So there can be one feature that caused the problem. I made my own iPhone landscape skin and I was very pleased. Could somebody try this skin to see if it freezes their device?
Click to expand...
Click to collapse
I'll give the skin a test run in an hour, but I refuse to use plug-ins again. They have always caused me problems, but WA2 never has. What version were you running?
Tried the i-phone skin and have experienced no issues whatsoever.
Maybe the Problem is WAD and your plug-ins.
WAD keep on giving problems like this...it's a sin for such an interesting application...here it is because I gave up to use it.
Mrsums said:
All the tests I have tried suggest it is Wisebar Advance 2 that is causing the freezing.
Click to expand...
Click to collapse
I did some searching and found some suggestions it might be the skin I was using. I changed the skin and no more freezing.
Robert
trayap.exe
Since I removed the trayap.exe from the init part of the registry I did not have any freezing anymore. I will try WA2 again to see if this solves my problem.
By the way, I am using the latest beta's of WA2 and WAD
hi all
i find that if i use the off button to turn off the backlight whilst media player is running it jams the machine, requiring a reboot. i know that i can usethe light button on the keyboard but i sometimes forget that media player is running (ie. paused).
I have the same freezing problem now after a few weeks of usage.
The device was running very nicely but now, without installing anything further or adding anything to the device, it freezes randomly.
It likes to freeze when the backlight goes off, while I play MP3 files or have a phone conversation using bluetooth.
In the past 4 days I have softreset the device no less than 81 times.
I suspect the Microdrive is to blame. Is it sensitive to movement?
I will remove all my software and other files from the microdrive and see if things improve.
In the mean time, has anyone else experienced random and frequent freezing?
Oh, I have the Dopod U1000 branded device with the latest firmware.
ok, I had it with this. 16 more soft resets within 4 hours.
I hard reset the device. So far I see no random freezing, but I didn't install anything extra yet except ozVGA and VJBigPhone. And both of them on the internal memory, so nothing on the microdrive.
In the past couple of days, there has been three occasions when the PPC (Orange m700) would not resume from standby by pressing the on/off button.
It was still on, but not responsive at all and required a soft reset. It would not wake up with a regular pre-set alarm, and nor with a phone call either - calls sent straight to answerphone.
I uninstalled some software after the first ocasion, as I though that may be the problem, but apparently not.
I can't find any other forum posts on this probelm either
Hmm, I'm having the same problem since upgrading my P3600 to the latest official HTC ROM. Unit appears to be in standby but cannot be woken using the power button. Haven't tried calling it in this state to see if a call will wake it.
No idea what could be causing it, soft reset seems to fix the problem.
Anyone else with this problem?
before i have same problem like both off u, did u install u'r device with c3 st4r wm5 cr4ck?? because when i have install with that prog my device in black screen i couldn't wake my phone again & tried to call my device but the phone not active, now i'm using the original c3 st4r serial number from dopod for free, my device just work fine
I have recently noticed mine doiing this as well, although if i hold the button down for a while it will eventually wake up. I dont have a crack for core but have a serial posted on the XXXXXXXXXX site- didnt get a serial or the program with my dopod..... can someone help me with a different serial?
Mod edit we do not make WAREZ suggestions on XDA-Developers
It's happened on mine a couple times recently. For the moment, I'm attributing it to running the gmail applet...no theory, just based on practical observation. A friend recently installed opera mini and had the same problem on his device (it's an HP6515). Could it be the midlets?
i dont use midlets, and i have the same problem and worse... some times everything stops working even in standby mode, or when i use it it crashes and i have to wait some time before using it or i have to soft reset after a long period... it is not a software problem because i uninstalled alot of heavy progs, but i think that mini sd might be corupted and the apps using it crashes,(us when i listent o the musing file paths are gone and i have to softreset)
im just trying using the mini sd as hdd in windows through the phone and do a checkdisk and defragment to see if the problem resists.. if it does ill paint blue my trinity and throw it to the see *(greek exprsion).... ime so ungry of those stuck problems, and i think we gave so much money and we cant even recieve phonecalls...its a pain in the a**
This has happened to me on occasion.
I am wondering if you guys check mail (use HDSPA?)... I have a feeling this may be the cause...
happens every now and then, suspect batterystatus plug-in which is not really meant for trinity, but could be some other software...
For the past three days the phone was frozen in the morning.
I have two alarms set to get me up, and there have been a couple of reminders (tasks), so I wonder if these are related to the problem? The alarms never went off!
Also my phone memory is now round about 12mb, so I also wonder if this is an issue?
Also, it has taken me 2 soft resets to get the phone working again after it froze the past 2 times
I have noticed the same issue for a while. In my case at least I think it relates to wifi (and maybe BT). If left on my phone doesnt typically emerge from standyby. If I switch off then I dont seem to have this problem at all. Maybe not just me?
Guys, I suspect you have a software problem. I know it's painful, but you can do a hard reset to the device so that it returns to its clean initial state and test for a few days to see if it's recurring.
Then you'll know if it's a software problem or hardware one. Also, it helps you to explain the situation when you ever need to return it.
Had the same problem. Drove me absolutely nuts. Had phone exchanged 3 times and did numerous hard and soft resets. Virtually no additional software on it. Finally resolved after switching to WM6. Thank god!
i think it's a hardware problem.
I have a trinity now, but I had this problem with my atom exec. it would do exactly that... turn off, not turn back on, power button doesn't work, people think im not answering my phone, alarms don't sound. I tried all the roms, including changing my WWE rom to a CHT rom, didn't work, same problem.
I'm interested in hearing why people think this is software related.
i have the same problem with my p3600 :| sometime it don'r resume from standby when i press poweron/off button :| any solution?
I think you'd better send it back to HTC.
I had the Standby of Death SOD this is when the phone fails to come out of standby with a power button press. This issue only affects some people on some networks. I'm not sure if its a network problem or a software problem but as only a minority of people have it, I suspect its mainly a network problem there is a software solution.
The solution is to change the phone settings band option from auto 3G/2G to either 3G Only (WCDMA + UTMS 2100 in Europe) or 2G Only (GSM + AUTO) depending on your requirements.
Also read this thread http://forum.xda-developers.com/showthread.php?t=540943&highlight=standby&page=2 where the resolution was to get a new SIM.
Obviously this only solves the problem when the crash is because of the sim and/or settings which impact the sim. To rule out a software cause its best to start with a hard reset.
try this
problem phone freeze from standby often hapened to me then i try to install "SystemSecurityMonitorPro(V2.2)"
use it before turn on phone from standby
i dont know how it work but it working for me
correct me if iam wrong
hilang said:
problem phone freeze from standby often hapened to me then i try to install "SystemSecurityMonitorPro(V2.2)"
use it before turn on phone from standby
i dont know how it work but it working for me
correct me if iam wrong
Click to expand...
Click to collapse
I'm not going to try and correct you as there can be different solutions to the problem depending on the cause, my solution will only solve the problem if its because of the sim/radio/network, other solutions are to update the radio, get a new SIM, do a hard reset etc etc etc. If it worked for you then it worked for you and your post is welcome.
I have a trinity and until Friday loved it. Suddenly it has started to automatically reboot itself every 2 minutes or so.
I have loaded NO new software or changed any settings for months. But reviewing the drop menu I see 2 SPB software icons have now gone blank. SPB Traveller and SPBWallet. I assume it is a software problem even though have worked fine for 8 months.
I have deleted the software but still have problem. I also still have the two blank icons on menu.
Tried a Hard Reset but cannot reset. Tried a soft reset but will not action the reset button.
Absolutely frustrated as it just loops and even the old Hard Reset is not working. Anyone had similar or heard of a way to fix?
Den
Im having a similar problem with my spv m700 most of the time phone works fine then just reboots for no apparent reason (phone does it even when sat in car holder so cant accidently press a button). sometimes just does it the once other times it reboots 5 or 6 times and others it reboots a couple of times then crashes at the orange screen and has to be reset. mainly seems to do it while running tomtom but that could just be because it runs that most of the time anyway hasnt done it while making a call yet.
phone is running
radio 1.56.70.11
rom ver 6.1.21054
wm6.1 ceos 5.2.21054 classic edition by tomme45i (have tried other os versions but problem remains)
any help ideas would be much appreciated
Do you use bluetoth head set?
Is the software (spb) intaled on main memory or storage card?
no i dont use bluetooth and the software is installed in main memory
left tomtom off today and phone still reboots? so dont think its a tomtom problem also doesnt matter if the phone is pluged in or not still the same