My modem is disconnected each time I initialized a connection (the connection settings comes from SFR).
I have upgraded my mobile with WM 6 !
Please help me !
Pat
Related
Hi,
I try to connect my QTEK 2020 to a Windows RAS Server using a data call !
My problem is that the modem connection is OK, but not the autentication !? After 2 tries, the remote server disconnect the line !?
Is this possible ? If yes, can someone help me ?
Thanks.
Sorry for my bad english !
Please Help!! My head is about to explode!
I have upgraded my SPV M1000 with w2003 se Chinese version, which works well no problems with that. However, I Have Widcomm version 1.5.0 build 0801, now I can activesync to any of my PC also Pan network works fine.
My problem is I cannot connect my notebook to the SPV and use the GPRS modem.
I have seen that I have to put a extra command in at+cgdcont=1,”ip”,”orangenet”,””,0,0
When I try to connect it say hardware failure 692 connect though.
If I leave the command out it say’s it connects to orange username and password ok then disconnects me saying PPP error.
Can anyone help
Many thanks
Hi all,
Yesterday I was trying to set up the JasJar to serve as USB modem for my laptop. I have found a complete step by step manual on http://forum.xda-developers.com/viewtopic.php?t=37298 post. I have tried to do all steps twice to be sure that everything is OK. But after 10 attempts to establish the connection I have gave up.
My phone is in Orange network in Poland. User name and password to access the internet from PDA via GPRS is ‘idea’ and ‘idea’. The access point name is ‘internet’. Those setting works fine on my PDA and should work as parameters for the Dial-up connection on the computer as well.
While I connect to the internet on my laptop via JasJar the connection process stalls on “Registering your computer on the network”. After that after few more seconds the GPRS connection on PDA is being disconnected. Does anybody know what’s wrong?
I have installed the latest version of the firmware available on iMate site (JASJAR_WWE_13076_164_10900_wwe_ship.exe)
Best regards
Marek Suski
Hi,
had the same problem with it in the beginning.
If you followed the detailed description I can only assume this problem:
You missed to insert the APN in the Wireless Modem driver on the PDA (this piece of Software is on the PDA; I have the German version where it is called "Funkmodem").
Go to Extras | Options at the bottom left within the Wireless Modem and tick the option you see there.
Then again insert into the box "Access Point Name" the correct APN of your operator.
Then it should work.
I think you know that the modem on the PDA has first to be started and then the PDA connected with the PC, because otherwise ActiveSync would start.
Post here if it works now or if you need further help !
I actually have a different problem: I've set it up as per the guides. But when I want to start the connection it doesn't work. Here's what I do:
1. Disable USB connecctions in ActiveSync
2. start Wireless Modem on MDA Pro
3. Connect cable to MDA
4. Start the connection. It starts dialling, but after 10 seconds comes up with a 692 error code. Apparently, this means: "Error 692: There was a hardware failure in the modem (or other connecting device)."
Also, when I look in the Wireless Modem application, the little square indicating Connection activity always remains yellow. I presume that upon succesful connection it will turn green?
Any thoughts, anyone?
can a friend use my GPRS connection from my windows mobile device (o2 xda orbit running WM6 B&B 4) on his PDA if i setup interent connectiopn sharing via bluetooth and he pairs to me ?
I tried to make it work but failed, any advice / tutorial ?
Thanks
Hi, I'm from Brazil, meet you.
The question:
I have an HP hw6945 Mobile Menssenger running the WM 5.1 CE
The Phone not found. The operadora is Tim 1800Mhz.
No service.
Shows this error:
"Network Error:
Unable to read setting from the network. Try viewing settings later, or disconect data connection and try again.
Retry / Cancel"
How fix this?
Can you help-me?
Thanks