Related
i accidentally drop my xda2 earlier today. it was in inside an innopocket aluminum casing but it apparently hit a stone on the sidewalk right at the upper left hand corner, where the bluetooth LED is. it cause a rather ugly scratch on my xda 2 and bent my aluminum casing. fortunately, my xda2 is still working fine.
i was wondering if it's possible to replace the casing of the xda2? where and how much would it cost? as this obviously would not be covered by the warranty.
The cheapest way is to acquire a dummy phone and use the case from that.
rodnav said:
i accidentally drop my xda2 earlier today. it was in inside an innopocket aluminum casing but it apparently hit a stone on the sidewalk right at the upper left hand corner, where the bluetooth LED is. it cause a rather ugly scratch on my xda 2 and bent my aluminum casing. fortunately, my xda2 is still working fine.
i was wondering if it's possible to replace the casing of the xda2? where and how much would it cost? as this obviously would be covered by the warranty.
Click to expand...
Click to collapse
Wow rodnav!...
Maybe we live in paralell universes since I dropped mine (which was in it's original leather case) and when dropped it hit a small stone on the pavement and it scrached and dent my MDA2 just on that same spot... it just missed the bluetooth led my a millimeter!
I want to buy a spare casing too!
Let me know if you had any luck finding one...
thanks guys.
i saw a dummy xda2 at a shop recently, i wonder if they'll sell it to me...
used windex on my screen and the digitizer went bad.
any recommendations on where to purchase a new one?
thanks pogo
on eBay! ...
cnn.cn 7.99$ I have to order one this week, just have to get around to it.
cnn.cn BINGO !
:d :d :d :d :d :d :d :d :d :d
8525 Digitizer Installation...
Hello,
I have an 8525 with a broken digitizer (LCD OK). I replaced the whole unit with a new combined LCD/Digitizer. It is a pretty straightforward repair. It took me all of about 15 minutes (you just need a #6 torx and a jeweler's phillips).
Just in case this happens again, I purchased a new digitizer (only). I want to remove the old digitizer from the LCD screen and replace it with the new one. The problem is: the digitizer ribbon cable is attached to the LCD screen, possibly soldered but I can't tell. Are there any instructions anywhere regarding the digitizer removal and installation?
Thanks
Im new to all this whats the digitizer exactly?
The digitizer is the top portion of the screen. It's what registers your stylus' contact on the screen. It lays on top of the LCD and it looks like 1 piece, but its actually two. And for those wanting to know if the digitizer is soldered, the answer is no. It's held in place with tape, but it is easier to just replace the combo instead of just the digitizer. Most often then not, when removing the damaged digitizer, it will crack and may possibly damage the lcd, or so I've read. I just recently cracked my lcd, so i got a combo and switched it out, just to have a scratch on the digitizer the following day. That's life. Waiting for my next new combo to come in the mail.
You'd be better replacing both the lcd and digitzer as 1 unit than try to unglue and reglue the digitizer onto your screen. A lot of hair pulling and screaming involved and no guarantees it'll work. For the $100Aud I'd just replace the lot in one hit. As markus1959 said its a 15 minute job but stuffing around with just the digitizer is a major hassle. Even Mike Channon (he's the hermes hardware guru) advises against that unless you're really into pain and frustration....
Cheers...
Hi,
from where do you all get a new LCD (+ digitizer).
My LCD is cracked (digitizer OK) so I need replacement.
I live in Switzerland and I can not find a shop with a reasonable price.
I am trying to remove the rigid flex board from the screen portion of the Wizard (8125). I can get the backing detached from the screen but it feels as if something is caught and that I am snagging something when trying to seperate the two pieces. I just ordered a flex board with ribbon cable and need to install it but do not want to destroy anything with the LCD screen. Does anyone understand what I mean or have any advice on getting the pieces apart. I read the service manual but can not get past this point. TIA.
I have had mine apart a number of times, (2 lcds and a flex board). There is a sticky tape of some sort in between the board and the lcd. I slid a very slim peice of teflon in between to seperate the two, and viola!, apart it came.
Hope that helps ya.
grumpygeorge
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Congratulations!!
mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
How did you attach the digitizer to the LCD? Aren't they glued together or something like that?
Because that's where my attempt went terribly wrong: Instead of getting the digitizer off my LCD, I broke my LCD... I bought a new complete screen unit because I didn't know how the LCD is attached to the digitizer!
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
mrmomoman said:
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
Click to expand...
Click to collapse
Thank you for your explanation! But I'm still not going to attempt this on my own any time soon... We'll see... Maybe I'll change my mind if my digitizer is broken or scratched...
Respect man! You mentioned that you bought digitizer for $17. Is it possible to buy mainboard for Touch HD from that place? Can you please advise where I can get it. And how much it will be?
Got to love a bit of micro-electronics DIY!
This just shows that HTC are taking people for a ride - there are a lot of people who would have just paid the price they stated. As you've only replaced the digitizer, shows they were taking the mick with the LCD and otherwise, what are these "internals" that HTC said it needed I wonder...??
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Have you got the link for the service manual?
Ive just had to order a Digitizer as my phone has decided it doesnt want to work anymore (6 months to go on contract too ffs).
Managed to get one from a UK seller with tools for £17 so im happy.
KickAssMoves said:
Have you got the link for the service manual?
Click to expand...
Click to collapse
It's in the wiki.
WelshWarior said:
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Click to expand...
Click to collapse
Hi:
How did you get the digitizer separated from the LCD?
I was thinking of putting two suction cups (1 on the back of the LCD, and the other on the front of the digitizer), heating everything up for a couple of minutes with a heat gun, and then pulling them apart holding the suction cups.
Does that make sense?
Thanks.
mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
i just had mines fixed called them told them wat i did that i found an outer sreen and tryed to replace it myself and completely destroyed the lil black screen inside of the 4screens put together and that my device software was moded now i had 469 out going and another 469 incoming calls they only charged me 113 but wen we first talked about it they did say about 350 until they see the device and then they will call you before the repair it but the did wipe out my device and reinstalled the oem rom they also gave me a full new body and zero'ed out the incoming and out going calls which never changest unless they put in a new mother board which makes my phone brand new
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
pickie said:
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
Click to expand...
Click to collapse
Mine had that pearl essence look to it for a good few months before it broke, not that im sure that has anything to do with it.
Just awaiting the delivery of the digitizer and hopefully I can repair it.
yeh mine had the pearl effect for a long time prior to it dyeing
ive followed the service manual and the video of the guy who gets stuck near the end, but how do you g et the screen out of the casing to get to the digitizer?
Its one hell of atight fit and i cant see anything o bvious.
Help
Hi Guys
Sorry about the late replies - had phoneline probs!!
Assuming you followed the instructions in the Service Manual to take the rest of the phone apart, you've just gotta be VERY careful and push the screen out from the back (where the Circuit Boards where) of the plastic frame. At first, it feels like it's not budging but be patient and it WILL start to push away.
It seems to be held in with some sort of hot glue or maybe a contact sort of adhesive and I didn't try it but some heat from something like a hair dryer may make the job easier.
Many people have cracked their LCD screen during the repair but as long as you're careful not to bend the screen too much when taking it out, you'll be fine.
I peeled the 3 layers (outer glass ones and then the Digitizer itself) off the LCD whilst removing it.
Good luck - it's really not that hard. Any more questions - just ask ;-)
ive got the phone apart to the point of the service manual/video
which part of the back do you push out? doesnt look obvious as to whats attached and what isnt
Once you get to the last stage (I thinks it's the Speaker Removal) you simply push on the metal protector of the LCD from the back. You will see small holes in the plastic of the back of the frame where you can push something blunt through and push very lightly on the LCD to push it out.
If I remember correctly, at the bottom of the phone where the circuit board with the vibrator and microphone on it was sitting, there is quite a large opening with the metal backing of the LCD visible through it. I started pushing there and gently went all around the phone in the various small holes dotted around it.
As I said above, it won't feel like it's working at first but it will - just be patient and not too heavy handed!
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
::Pixel.Freak:: said:
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
Click to expand...
Click to collapse
More liked taped in...... I'm sure that lots of people will respond with.. Double sided 3M tape.... but if there's anything better/stronger than that on the market use it. Make sure it''s really thin tape to. I'm gonna be replacing my housing in the next month or so aswell. Goodluck.
As I also will replace mine digitizer, the newton rings are bugging me, it will be appreciable if you can share your experiences of the replacement process.
thanks in advance and god luck
Hey on more thing. I took apart my phone last night and put it back just so I know my way around when parts come in.
If your Digitizer does not work try loosening the top srews 1/4 turn. You have them on too tight.
I wasn't replacing mine so I didn't have to remove the existing one. All I had to do was attach a new digitiser to a new housing.
I was told that double sided tape was the best, so I tried that.
I used the instruction from http://www.pdacenter.ru/razborka/htc-touch-diamond2 which was easy enough.
You need to ensure you remove the micro SD card first.
Also I forgot to move the LED diffuser from the top, so I need to repeat the process at some stage.
The housing I bought had a number of issues
* The two screw point near the bottom of the housing didn't have the metal inserts with the screw threads
* There was no seal between the metal housing and the LCD screen. This could let dust in.
That's about it for a brain dump.
Hi there,
I was also tired from that oil stai and ordered a new digitizer from these guys:
http://xxx.sw-box.com/htc-touch-diamond-2-t5353-digitizer-touch-panel-screen.html
Surely it arrived in 6 days, to my horror it was a generic display,
Had some trouble removing the old one, ended up breaking it
The generic did not fit snugly, I had to sand down the edges to make them round, also had some trouble with the four buttons below getting stuck when pressing down, (shaved of some extra plastic). anyway used double sided scotch film to get the digitizer back in place.
apart from a few difficulties, it works like a charm.
Should have ordered an OEM but what's done is done
Next time I'll do the cover and get a new digitizer
Regards
I would of thought double sided tape too thick to use to stick the digitizer on.
I was thinking of using a very thin sliver of clear silicone.
Anybody tried this or have any other suggestions?
Thanks
I used a very thin layer of supergleu and it worked great!!
My digitizer came pre-glued. I didn't need any sort of glue.
http://forum.xda-developers.com/showthread.php?t=715724
Silicone is OK
I used a very thin layer of black silicone and placed a book on top of the digitizer to keep it pressed flat into the case as it dried overnight. No problems since then...
The missing metal screw inserts can simply be pulled out of the old housing ; insert screw halfway and gently pull with plyers. Carefully hammer into the new casing; insert screw 3/4, put something thin and metal on top to prevent the screwhead from getting damaged and carefully hammer into the void. Make sure it goes in straight.
I've got exactly the same issue with my new housing, no bottom screw threads and no foam for the lcd to rest on. Am trying to pull the threads out with pliers but I think the old case is going to break first or strip the threads.
This is isn't an easy job
have finally finished this epic!!!!
had to break the bottom screw threads out of the old front housing and took a good while hammering them into the new housing so I didn't break it.
used a small sliver of clear silicone to glue the digitizer in which seems to work well so far.
Have not put any foam or anything for the LCD to rest on, time will tell what effect this has.
I need to change mine as well. Where can i buy a good quality digitizer and case preferably pre-glued?
I found a few on ebay but i am not sure of the quality.
Thanks
Today i searched also for shops which have digitizers and housings. I have found 2 shops, but one of them is a german shop (http://www.mobileok.de) which does not deliver outside of germany and austria. But the other one does: http://www.sw-box.com/
what kind of glue? it's the third time that i'm re-gluing it, but dust keeps coming inside....
I guess, it is not possible to hermetical seal the housing. I had dust in my original housing too. There are a lot of small gaps everywhere not only between digitizer and frame. But it would be easy to disassemble the device from time to time, remove the dust and reassemble it again. Save your energy in the effort to make your device dust proof.