Hi all,
I'm having problems getting ActiveSync (on the phone) to be able to use the WLAN connection to connect to the internet and sync with my exchange server. It takes forever otherwise, even when I use the 3G connection. I understand that it's not possible to sync with a desktop over WLAN but I was hoping there'd be a way to get ActiveSync to treat the WLAN connection like the cellular data connection and just get on the internet.
Thanks for any help!
I have exchange in my office. If you want to use the WLAN (wifi), the exchange server address is usually difference than if you were using 3G (internet). Unfortunately, the 8525 only let use key in one server address, so when you are in the office...you have to turn off wifi....unles you want to retype your the address.
I key in the server address that i use to access outlook web...so if i'm not in the office, i can still get email. It is easier to turn off wifi when i am in the office.
Related
Hi,
I've got my jamjar to active sync with an exchange server directly,
and via a VPN server.
It will sync using the VPN server from my home wireless broadband point thru the interweb and the VPN to the exchange server, But if I try this using GPRS/3G it fails (activesync spins for 8 minutes then gives up).
I know the VPN link is good cos I can connect to a remote PC with the terminal services client.
Is it something to do with the timeouts being too short to cope with the delay over GPRS?
Any ideas gratefully recieved.
I've been having a problem for the past week in that I could not connect to my Exchange Server or passthru to the Internet with and ActiveSync connection.
At least for the moment, on the Connections menu, clicking on "USB to PC" and disabling "advanced networking functionality" seems to have resolved the problem.
Anybody else run into this?
And what is this advanced networking, anyway?
I've also noticed that Sprite Backup would fail with it enabled, so it seems I've solved two problems at the same time...
i had that issue as well the work around i did was connect to my wifi connect my device to my pc sync then disconnect my wifi
still a pain
I've always just connected straight to the server over GPRS/UMTS. I haven't even installed Active Sync on my new PC.
hi Folks,
i have the same issue with Active Sync. I am using Active Sync for syncronizing emails, contacts etc ... I have discovered if you installed the device (hardreset) then you may able to sync with the exchange for the first time. After that you are not longer able to sync it.
I used different ROM's (Dopod, Qtek,O2) all have the same problem. I am not able to sync over Active Sync (4.2 latest and prior versions) with my exchange server. I need to sync over 3G Network and thats a bit expensive over the time with O2.
I think this device is more than incomplete since i am using a Wizard too and i have no problems with the same pc on my Wizard device.
I hope there will be a ROM update really soon that covers many issues discussed in that board here...
At least i am really disappointed about the device which HTC sold over the market.
Hi
On mine this works! - nevertheless i am using the IP adress - could be a hint for you guys
BR
Daniel
do you mean the IP address from the Exchange Server? Or do you pair your device with static IP addresses? :?:
Well ...
I got mine to work after i discovered that the proxy server i placed under gprs connection denied the connection to the exchange server. switching all to MyISP resolved the issue.
If you use a firewall try to look which address the RAPI Manager tries to connect to. Maybe that helps for you to solve your error.
Hi
I use the IP adress for the exchange Server name. The connection Between laptop and device is negotiated automatically
I've set up mail2web account and configured activesync on my mobile with mail2web settings for push mail.
I've been unable to get any mail "Pushed" to my device that way when I'm connect with WIFI. I have to go to acivesync on mobile and click on "Sync" and only then do the emails get downloaded to the device.
I've been searching through the archive and I actually found people saying you cannot use Wifi with pushmail. But also found replies of some claim they are getting their mail pushed while being connected only with Wifi and not GPRS.
Keep in mind at this time my device doesn't have GPRS so I have no other choice but to use Wifi. More so, it would seem very idiotic to program pushmail to specifically not work through Wifi. After all why not? Wifi is a lot faster, and if you're at the office or an hotspot somewhere it would seem much more logical to get the mail with Wifi than with slow GPRS. but I wouldn't be surprised if MS didn't think about that.
push mail won't work with WIFI
use cellular line and it works straight away
Or use Blackberry or Goodlink or any other push e-mail solution.
You can also move to the Nokia implementation using ActiveSync for push-email on the E61 and that will work with WiFi :twisted:
I think push email does work on Wifi.
The only thing is that my GPRS connection pops up automaticly. But when I want to send a large email, i need to disconnect GPRS several times in order to send it over Wifi
arjan
This irritated me as well, but I've found that if you modify the ActiveSync schedule to sync every 5 minutes instead of "as items arrive" you can connect to Exchange servers over WiFi.
You won't get true push email, but it's still better than nothing
check out the mobile team blog. Push on activesync is hardcoded to use cellular only. nothing you can do will get it to work on wifi.
Hi all,
I set up my Trinity to also check my hotmail account. Ofcourse, when I do this outside the confines of my home Wifi network, the P3600 automatically connects to hotmail via my UMTS connection.
When I'm on the road I don't mind this, but when I'm at the office, where there is no wifi, I would like to use the connection my PC has to the internet. I was thinking about using BT for this but don't know if this is possible at all...
Anyone with suggestions?
I don't think this is possible via Activesync, but if possible I would like to avoid the use of it anyway...
Thx for any suggestions!
if connected to activesync one is connected to the network of the pc with activesync
unless steps have been made on the pc, pda or office network to block it
i surf with bluetooth connection to activesync all the time
Likewise i use the USB active sync connection to connect to the internet on my Trinity, and Alpine as well. The only restriction, as mentioned, is that if the PC has limited access rights then so does the PDA.
Hey thanks Rudegar & deedee, I didn't know this actually
So simple and obvious, but I never tried it out
Guess I'll have to install Activesync on the [email protected] too then....
Hi, I'm using WM6.0
I have several question about Microsoft Direct Push, I greatly appreciate if anyone can answer these questions:
I just setup a direct push through my company's exchange server. Everything works fine but I don't get it:
1. I set my Activesync to sync "As items arrive". Then GRPS will start and start sync'ing with exchange but it will stay on and won't disconnect. Is this normal? GPRS is very expensive in my country, I can't afford to have it on all the time.
2. If I disconnect GPRS and close Activesync, when I reopen it, the configuration of Activesync changes from "As items arrive" back to "Manually" > is this normal?
3. If I set it as "Manually" and close the Activesync and disconnect GPRS and try to send an email to myself. It will not push the email like I expected. I have to either go to COMManager and click on "Microsoft Direct Push", which will turn on my GPRS and will make it stay connected to GPRS.
4. If I use WiFi and send an email to myself, I will not get push email. Unless if I go to Activesync and press "SYNC"
5. If I use BT connection to my laptop and start Activesync. It will only sync with server when Activesync sync'ing with computer.
6. Why does Direct Push doesn't work like a Direct Push, it's more like a Direct Pull to me? I always thought that Direct Push meaning that it will connect to GPRS and retrieve an email and disconnect. JUST LIKE MMS.
7. Is there a way to make it a real Direct Push? like it will connect to GPRS only when I'm about to receive an email. Or it will push the email when I'm connected to WiFi?
Thank you for your help. Any comment or any explanation will do. If anyone has a website that explains this, it'll be great also. I have done researches as usual before I post this email but I can't find any answer.
Thx again
Direct Push and 3G-GPRS
Hi,
Same problem and same question about direct push.
I bought a tytn with WM5 to Orange (France). With VM5, the synchronisation is ok with usb and GPRS / 3G also : The 3G goes up as soon as the usb is disconnected and falls down as soon as USB is re-connected up.
With USB, the scheduling is about 5 mns. With 3G this is really "As items arrive".
Today I use WM6 (schap' s 3.54b) with ROM radio 1.51.00.10. The difference with WM5 is the following: 3G / GPRS with pushmail is ok, but when I connect up the usb, the 3G connection remains active, but I think that it is not used by activesync. I'm not sure.
I think that the directpush works only with the 3G, never with wifi, bluetooth or usb.
However, I do not know what has an influence on connection. Is this WM6, the version of protocol or the version of ROM radio? I have not found any doc yet.
If you have any suggestion...
thanks too
Yes, I read from somewhere that push mail will not work over WiFi or USB. When you are using WiFi or USB, you must click SYNC manually to sync with exchange. It will not push the mail.
I hate that fact that the GPRS won't disconnect after getting an email. MMS works that why, why can't push mail be that way?
GPRS is very expensive in Singapore. I wouldn't use it for Push Mail. I just have to make sure that it's doing it manually not "AS ITEMS ARRIVE". That will hurt my pocket and kill me slowly with bills.
A simple explanation would be necessary...
What is push mail ?
Push mail is when the server send a signal to your device so the latest can sync an retrieve any new event signaled. What it means is your device must be reachable from the outside world : your device NEEDS an IP address.
So yes, GPRS (EGDE, 3G, whatever...) needs to be activated all the time, or else the server won't know how to send a signal to your device.
This is like asking someone to send you some package without giving him the address...
You can replace the GPRS with a Wifi link, btw it would need to be always on, and I mean real ON, not the device falling a sleep. The PDA would run out of power in less than 2 hours.
Via Activesync ? Good try. Unfortunally although the device has an IP address, this one is not reachable outside from the computer. Only Activesync classical synchronisation can do the job.
Hope this help.
foxenesys said:
A simple explanation would be necessary...
What is push mail ?
Push mail is when the server send a signal to your device so the latest can sync an retrieve any new event signaled. What it means is your device must be reachable from the outside world : your device NEEDS an IP address.
So yes, GPRS (EGDE, 3G, whatever...) needs to be activated all the time, or else the server won't know how to send a signal to your device.
This is like asking someone to send you some package without giving him the address...
You can replace the GPRS with a Wifi link, btw it would need to be always on, and I mean real ON, not the device falling a sleep. The PDA would run out of power in less than 2 hours.
Via Activesync ? Good try. Unfortunally although the device has an IP address, this one is not reachable outside from the computer. Only Activesync classical synchronisation can do the job.
Hope this help.
Click to expand...
Click to collapse
Then, how can you explain how MMS work? How can the GPRS turn on automatically when there is an MMS and disconnects after it finishes downloading the MMS?
Doesn't Blackberry do that?
bankir said:
Then, how can you explain how MMS work? How can the GPRS turn on automatically when there is an MMS and disconnects after it finishes downloading the MMS?
Doesn't Blackberry do that?
Click to expand...
Click to collapse
For blackberry, you need a gateway to format all messages from exchange to cell phone.
Only to supplement explanation: The pda opens a session via the 3G on exchange server.The channel is so supported opened. At the arrival of a message exchange point out in the pda that he must synchronize. Then it is the habitual process activesync...
But i don't know why the 3G connection isn't disconnected when i plug the craddle. May be the version of protocole version ?
Blackberry also has an always on GPRS connection/