Does anyone have advice on changing the touchscreen? and where to buy a new touchscreen?
Cheers.
Are you sure its the screen causing the problem? Did you try hard resetting your device?
You'll find a lot on ebay or Brando, otherwise do a google. Check the wiki for the right type first before buying especially if from ebay.
Thanks for info.
I have performed a hard reset and the screen still dead.
There are two LCD versions a gold or black cable. Do you know if they are both compatible with the Magician?
Since you are going to replace it yourself, why not dismantle your device and see what's installed.
Related
Hi,
I got my 8525 secondhand off ebay, and I'm having problems with it. I did a clear storage or a reset of sort, and I'm stuck in loop of screen alignings. Originally, before I did the reset, the touch screen does not respond when I tap on the top right, and the screen alignment loop was also there when I chose to align screen and I had to take out the battery to fix it. I notice small pieces of cardboard stuck in between the side of the lcd and casing so would that be the problem here? Any help is appreciated, thanks.
Sounds like the digitizer is stuffed... You may have to replace the LCD.
You can get them off EBay for $70AUD and there is a Service Manual so you can open and fix yourself. Here - http://michael-channon.spaces.live....ner=1&partqs=cat=Download+HTC+Service+Manuals
Its not too hard but you will need a small flat blde screwdriver, a small phillips head and a size 6 torque key.
All the best of luck,
Cheers...
Thanks Ultramag
I did a bit of research, and I came across this thread. http://forum.xda-developers.com/showthread.php?t=405432
It seems we both have a similar problem. Would the software method work for my case? I want to avoid dismantling the hardware if possible.
Thanks again.
Yes and no. You need another Hermes (same model) to get the alignment settings from and this is only to get the phone operational so you can use it. It WON'T fix the touchscreen, Its just a stopgap measure until you replace the faulty LCD.
I was lucky as I have a few friends who I sorta got into the hermes who I could get the settings off. You can navigate around your hermes without th touchscreen but its a REAL *****. Bought a couple of Jasjams off the net and was lucky enough that BOTH worked. Still put my mainboard into 1 and gave the other to a friend who was having similar issues...
Hope that helps...
Thanks mate, I really appreciate it.
Ok I need help from the gods of xda
I dropped my tilt the other day. When I picked it up everything seemed fine, yet the screen was completely white. No signs of cracks or a broken lcd. So I've tried the following: Soft reset, Hard reset, took out the battery, took apart the phone and disconnected the lcd and then re connected it. Still the same problem. WHITE SCREEN!
I can still receive/make calls, when i touch the screen in places where i remember the menus to be it still responds due to the noise, also the open and close noise still sounds.
The phone was bought new on Ebay, so i don't have a warranty through them or AT&T. After much research I hear people saying the same has happened to their phones as well and that there is a ribbon or flex cable problem. Something about still giving power to the LCD but not data, thus the white screen.
Now what I dont understand is do I need a new LCD because it has that ribbon/flex cable on it???? (link)
or
Do I need this product?(link)
Both contain a "flex cable" so im confused and frustrated, someone please help! any ideas would help
whew bought an LCD with digitizer on ebay for $45 and fixed it. Very easy process
vsicarbon said:
whew bought an LCD with digitizer on ebay for $45 and fixed it. Very easy process
Click to expand...
Click to collapse
hi there, would it be possible to post the link to ebay item? i also need a new touch-screen.tnanks
I am curious about this as well. I have a friend who has a hermes and he mentioned to me that that his screen was starting to go white like explained here. I look at his phone and I also noticed that the bottom hardware keys were not working at all.
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Anyone have any experience with this?
Thanks,
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Click to expand...
Click to collapse
That i dont know but here is the link to the LCD screen w/ digitizer
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=350099750789&Category=162&_trksid=p3907.m29
Same product and vendor I got mine from. Shipping took 3 business days. I advice to buy the insurence
Park City said:
I am curious about this as well. I have a friend who has a hermes and he mentioned to me that that his screen was starting to go white like explained here. I look at his phone and I also noticed that the bottom hardware keys were not working at all.
I am wondering if this same ribbon cable for the LCD would also be the same one for the bottom keypad and if I fix the screen the keys will become active again.
Anyone have any experience with this?
Thanks,
Click to expand...
Click to collapse
Tuck in for a long read and perhaps no single answer for all cases:
http://forum.xda-developers.com/showthread.php?t=303872
In short, yes the d/pad cable and LCD screen connections are linked which is why it is not uncommon for the white screen to show up when the d/pad is not working.
To the OP - I would just point out that if you get the white screen after a fall it may just be a loose connection at the d/pad and no need for new parts.
Dismantling instructions here:
www.mikechanon.net
But let's not start discussing the white screen here, please use the first link I gave above if you need to post.
Mike
a user i dont recall now his name,fixed is whitescreen by replacing the camera,open the device and remove the camera module, reassemble to test.
I have a cracked digitizer and got a replacement. I've replaced this in the past no problem. However, out of the two new digitizers I've tried, none seem to be working. The screen comes on ok but cannot tap anywhere. I've hard reset the device and now I cannot use the phone as I'm asked to align the screen. Any ideas as to what has happened? I've opened it up a hundred times each time checking the connection. Now possibly I need to replace the whole lcd screen but am reluctant to do if it still will not fix my prob. any help is much appreciated.
I just know there are two versions of LCDs (with digitzer) for the P3600. You have to check the serial on the back and get the exact one. Maybe it`s the same for the digitizers and You got some from the other serial line ?
Hi
i'm Claudio from Italy and my htc display suddenly became black
When i push keys the keyboard light and i hear bip but nothing in diplay.
If i connect to PC i see the files and the SD .
I'm not expert so i ask if there is a solution or i must throw away the HTC.
Thanx very much
You might be able to sell it for parts, got get a new LCD screen
hi,
do you think it's no possible a software problem(virus) ?
Tnx
Claudio
Welcome to forums
To discard that a hard reset should be done, but have in mind if it´s the screen problem that maybe you won´t be able to use it.
Good luck,
It sounds like most likely a flex cable problem. Flex cable and hinge can be purchased on eBay as one unit (the assembly makes separation impossible), however, there is always some danger that problem may be caused by the LCD itself or the mainboard. The only way to diagnose the problem is by process of elimination - to try your board in another working machine and then trying another screen in your device.
OK
I'll try
Thank you
I'm guessing this is your problem =] (oj)
http://forum.xda-developers.com/showthread.php?t=647177&highlight=Win_XP
klawrix said:
Click to expand...
Click to collapse
lol - i new you would like =]
nigma1nz said:
It sounds like most likely a flex cable problem. Flex cable and hinge can be purchased on eBay as one unit (the assembly makes separation impossible), however, there is always some danger that problem may be caused by the LCD itself or the mainboard. The only way to diagnose the problem is by process of elimination - to try your board in another working machine and then trying another screen in your device.
Click to expand...
Click to collapse
Where could i purchase such parts, As i'm thinking of revaming my uni with a new case and screen bits as well as a new battery =]
- i've found a case for the vodaphone version which is sliver, but gives me a full re-kit : Screen case, Keyboard case, + Keyboard.
but tbh i really want a new full black XDA Exec (02) re-kit with the same parts
Hey Volks,
Today i realized strange display issues with my HTC Touch HD. The ROM on it was original by the Provider (Telekom Germany) so i doubt it is a Flashing issue. I attached a screenshot for reference. Now my question: Seems this to be a hardware or software issue? Is flashing something that could solve this issue? If it is a hardware issue, would it be a good idea to repair it by myself? (i'm not complete stupid ) - What needs to be replaced? It seems that the touchscreen himself is working (pixels changing when pressing on the display).
Greetz,
Matthias
hi dude,
this seems to look like a hardware issue.
but..
i would flash a new rom or hard reset to check if it is software issue.
if the problem still exists after a reflash or hard reset, i would open your device and have a look for the problem yourself (its not rocket science )
you want to check the ribbons that connect the LCD to the motherboard.
(ribbons are clamped to motherboard so make sue you unclip the clamps that hold the ribbon in place, now check them for damage, dust or dirt)
be carefull though because the ribbons can break easily, trust me
after cleaning the ribbons, checking for damage etc, if device is still displaying like pic, i would buy a new LCD.
(ebay is the best place to go for a new LCD, it is best to buy an original LCD btw)