Serial Communication - JASJAR, XDA Exec, MDA Pro General

Hi,
I'm trying to put together a program for sending AT Commands over a serial connection from my PC to the XDA. Unfortunately my XDA doesn't respond to any of the commands, and in fact doesn't seem to be able to see any serial port data at all.
Does anyone know if there are settings I need to change to allow the XDA to be able to receive Serial data?
Thanks,
Simon

sure thing, the ultimate aim is to be able to send a command from a Destop PC to the XDA to get it to send an SMS. The specific method for doing this isn't too important, but atm AT Commands seems to be the most promising method.
Any advice you can give would be much appreciated.
Thanks,
Simon

Related

Using the XDA II as Modem with IrDa

Hi
I have been trying to use my XDA II as a modem and every time I try it give me a error. Error 692 Hardware Failure..
Can anyone pleasr help me with this?
I have a similar problem, please help!
I stopped trying via IRDA and set it up via the USB Sync cable, using GPRS. Works like a charm.
I was going cross-eyed trying to make it work and it wouldn't. Took about 15 minutes with the cable.
Is not working with the USB cable either
I had followed the instruction on PPC website (which seems identical to those on the XDA II official website):
http://www.ppcw.net/?itemid=1656&catid=80
but no luck... I'm still getting an error message... usually 732,
have you done anything different?
Please help Thx,
Chris
Did you successfully install the HTC USB Modem?
Was ActiveSync closed down, as it must be?
Did you use the USB Dialler program to make the connection?
Did it show the HTC USB Modem?
Was GPRS connected on the XDA?
Did you enter the correct User ID and Password?
A friend of mine tells me they're not necessary, as it works off your IMEI code, I've never tried it without them.
Dear ardarby,
Thank you for your help... here are my answers.
Did you successfully install the HTC USB Modem?
Yes
Was ActiveSync closed down, as it must be?
More than that: I disable USB a mean for active Sync to connect to the device, both on the PC and on the PPC
Did you use the USB Dialler program to make the connection?
Yes
Did it show the HTC USB Modem?
Yes
Was GPRS connected on the XDA?
I think so... how do I see it
Did you enter the correct User ID and Password?
Yes
A friend of mine tells me they're not necessary, as it works off your IMEI code, I've never tried it without them.
I am now getting an error which is something like error 734... any clue?
Thanks,
Chris
www.GB-SOFT.cz/XDAII
this tool should be able to tell you

Please help me unlock!

Hi to everyone
I have an xda (i believe its a wallaby) modelpw10a1 ram64mb. I want to unlock the unit, but have no idea where to begin.... i did follow peters advice for unlocking an xda 2 via the cradle/activesync/disable usb port method but nothing happens (apparently windows should recognise new devise)
is there a program i can run to unlock the xda1?
Another thing - i have just moved abroad to Thailand, the local gsm network here is very good so it shouldnt make any difference once it is (hopefully) unlocked?
Thasnks in advance
Matt
http://wiki.xda-developers.com/index.php?pagename=UnlockWiz/Wallaby
http://wiki.xda-developers.com/index.php?pagename=XDAunlock
Stefan
problem downloading it
http://wiki.xda-developers.com/index.php?pagename=UnlockWiz/Wallaby
Stefan, thanks for the link. The problem now is that when i click on the link, i get a 'authenticode' warning pop-up that stops me from downloading it.... licsence could not be found etc etc.
Any clues?
http://wiki.xda-developers.com/uploads/XDAunlock.exe
Sorry, its the above link that wont let me download.
the link works just fine for me
Frustration
I managed to get the unlocking file, and copied over to my xda... but the first thing it says when i open it is 'error getting the unlock code'
Is there another file i can use? Am i using the wrong one?
tried this one?
http://forum.xda-developers.com/viewtopic.php?t=24779
Massive frustration!
I cant believe how hard this is. Have been on it all day! Everyone else on this forum seems to be unlocking easily, am i doing something silly here?
Thanks for the latest link Rudegar, but im having the same problem - it wont open. On clicking the link, Im asked the usual ''run file from current location or save to disk'' either one gives me the following error message;
''the publisher cannot be determined due to the problems below.....''
''authenticode signiture not found''
''access to the specified device path file denied''
So in short, i cant open it.
My friend sent me the XDAunlock zip file, i transfered to my XDA but it came up with
''error unlocking sim''
So thats obviously the wrong file for my XDA...
I read that the XDAunlock only works if it has the wireless feature? How do i find out if i have wireless or not?
Sorry for sounding so clueless here, but really i am not to sharp with this sort of thing. Ive allways used my XDA happily till i moved abroad, now im buggered if i cant unlock it!
Someone please help!!!!
i think the link i just gave to the allinOneUnlock thingy requires to be run from the pc while the xda is connected to activesync
tried that
Rudegar, appreciate you sticking with me here...
No, its not a question of the cradle being connected or not im afraid, i tried that allreeady with both the cradle connected and also disconnected. It just wont have it, im totaly lost!
by cradle do you mean that you have tried with
the xda connected to activesync as in being connected after the sync is finished ?
or have you tried the xda connected but activesync not connected ?
have you tried another sim card to make sure it's still sim locked ?

linux (bluetooth) -> qtek 2020i -> fax out/in

hi ng!
i need a solution to use my pda qtek 2020i as "modem-device" for my linux pc.
i managed to get a rfcomm0, can send at-commands via this device, could dial out with a local software on my pc.... but,
if i try to use p.ex. efax - efax tells, that the modem does NOT support fax.
is there any way to solve my problem?
thanx a lot for any hints.
mario
ramsesii said:
i managed to get a rfcomm0, can send at-commands via this device, could dial out with a local software on my pc....
Click to expand...
Click to collapse
Can you do GPRS ? AFAIK, the gprs and fax data
go over different serial channel than the
AT command channel. You will find more
info here:
http://wiki.xda-developers.com/index.php?pagename=HTC_GSM
http://wiki.xda-developers.com/index.php?pagename=BlueangelProgress
hi!
yes - i can do gprs!
the problem is, that a sdp browse MAC only gives me channel 1 for serial connection, channel 2 for dial-up networking, and other channel (audio, file transfer,...).
thanx for the 2 links - but, the second is for mobile phones with linux on it - the first couldnt help me out.
i use normal windows mobile 2003 on my qtek 2020i - not linux (maybe i will sometimes )
any other ideas around?
thanx
ramses
ramsesii said:
the second is for mobile phones with linux on it
Click to expand...
Click to collapse
The hardware information doesn't depend on
the operating system
- the first couldnt help me out.
Click to expand...
Click to collapse
You can see that all the phones
use AT+FCLASS=0 as an init string.
What is the reply to 'AT+FCLASS=?' on alpine ?
You can also try:
AT+FMI?
AT+FMM?
AT+FMR?
AT+FCC=?
AT+FCQ=?
unfortunatly - nothing works.
my rfcomm is up: fcomm0: 00:09:2D:2B:EC:3F channel 2 connected [tty-attached]
but in minicom, which is connected via rfcomm0 all i get is...
Press CTRL-A Z for help on special keys
OK
at+fclass=?
ERROR
at+fmi?
ERROR
atdt
OK
AT+FCLASS=?
ERROR
AT+FMM?
ERROR
AT+FMR?
ERROR
AT+FCC?
ERROR
AT+FCC=?
ERROR
AT+FCQ=?
ERROR
quit
ERROR
exit
ERROR
bye
ERROR
AT+FCLASS=0
ERROR
this sounds.... not good
or am i doing something completely wrong?
thanx for your help.
ramsesii said:
at+fclass=?
ERROR
Click to expand...
Click to collapse
Hmm. Works as expected on my Universal.
It has something to do with your radio firmware,
maybe needs some special setup, or it is
simply not supported.
AT+FCLASS=0
ERROR
Click to expand...
Click to collapse
I don't know how the AT debug works on alpine (look up the registry keys in the wiki for himalaya), but
you may enable it, and PM me the log.
p.ex truefax works on my device... with it i can fax-out.
maybe i will go on that solution - is not what i wanted to have (faxout from the pc directlly) - but better then nothing.
hope RECEIVING fax will work with it.
thanx a lot for your nice help.

Enter PIN via C# or C++

Hi all!
Ok, I try it here...
Can anyone tell me, how to enter the PIN of the SIMCard to unlock my Blue Angle in C# or C++?
I would like to create a GPRS connection to the internet and have to enter the PIN first.
A code example would be nice.
Thank You
ENTER PINCODE
if your using AT commands
i think the command to enter pin code is AT+CPIN
i'm using Vb6 but i think it is somewhat similar
Mscomm1.output = "AT+CPIN="XXXX"
XXXX is the pin code hope this helps
Thanks for Your answer!
But I already tried this.
To send an AT Command to the modem, I have to open the Com Port COM2. I also have to send the DeviceIoControl command. All AT-Commands return success, even the CPIN command, but nothing happens. If I want to connect to the net, the dialog appears to enter the PIN.
Thanks for Your help.
Thanks for Your answer!
But I already tried this.
To send an AT Command to the modem, I have to open the Com Port COM2. I also have to send the DeviceIoControl command. All AT-Commands return success, even the CPIN command, but nothing happens. If I want to connect to the net, the dialog appears to enter the PIN.
Thanks for Your help.
Hi,
Have you tried to execute the "SimUnlockPhone" API in you app?
I don't know if this works but you can give it a try...
Regards.

Unable to send sms with the AT command AT+CMGS

HI,
I would like to knwo the AT command for the HTC Touch ( ELF)
I can communicate with my Phone with hyperterminal, but the at command :
AT+CMGS="xxxxxx"
Return ERROR !
I think that HTC don't use this command in order to send sms !
Have you information about the AT command in order to send SMS ?
Great thanks !
regards,
Nixeus
mm Anyone can help me pleaaaase ?
Hey ppl Im havin issues using my htc P3450 as a modem to send and receive sms via hyperterminal...pls somebody help!!!!
My system doesn't detect my phone under modems in the device manager!!
Getting WING to send SMS using Hyperterminal
Guys, I can only get AT, ATI, ATV1 to work.
None of the SMS commands work.
I'm using Hyperterminal: 5600,8,N,1
Anyone else got this working?
I am using samsung SGH-L700 for sending SMS using hyperterminal. But I am getting following error.
AT
OK
AT+CMGF=1
OK
AT+CMGW="+919509050003"
> HI (Ctrl+z)
+CMS ERROR: 321
I tried connecting using both bluetooth and usb cable. I am getting same error in both the cases.
Can anyone please help me for the same.
Thanks
Same for me, I need to use my old Elfin to send and receive sms. What are the correct AT commands for SMS sending and receiving ?
Regards
Same problem here with an HTC WIND ....when setup as HTX USB Modem at COM3 y can hypeterminal to it but only responds to ATIx commans...no SMS related commands accepted always error...any special driver ?
@Nixeus I had the same issue with my GSM modem, where I got ERROR and CME ERROR 765 after the sms command line. I resolved this by forcing the sms-encoding as suggested in a stackoverflow forum.
So, the command I used was :
AT+CSCS="GSM"

Categories

Resources