Database Users

Always on line for xda 1??

Any body knows for xda 1, you can keep checking new mail arrival through GPRS?
I heard people using xda 2 can do that. But is there any chance xda 1 can do the same thing?
Actually, when u do the setting for POP account, it ask u to set how many minutes to check for new messages. But it never work because the GPRS will close automatically.
Thanks very much. :?

Sure it can be done!
Take a look at:
http://www.o2.co.uk/productsservices/xda/romupgrade/0,,170,00.html
BTW the above is one of many!
also where are you located?
HTH

I am using the most updated PPC2002 version already. (3.20.06 ROM and 4.21 Radio)
Do u mean I have to upgrade to PPC2003?
I doubt that because they are not very stable for me to use in Hong Kong so far from other guy's comments in this website.
Thanks very much.

chris_khho said:
I am using the most updated PPC2002 version already. (3.20.06 ROM and 4.21 Radio)
Do u mean I have to upgrade to PPC2003?
I doubt that because they are not very stable for me to use in Hong Kong so far from other guy's comments in this website.
Thanks very much.
Click to expand...
Click to collapse
Since you're already running the latest upgrade its suppose to work but since it doesn't I would have to say that your always-on settings are at fault. So go to Start, Settings, Connections and make sure that its set to not disconnect.
HTH

Are you sure that it is also for xda1 ?
I can't locate that "not disconnect" setting.
Please clarify.
Thanks so much.

chris_khho said:
Are you sure that it is also for xda1 ?
I can't locate that "not disconnect" setting.
Please clarify.
Thanks so much.
Click to expand...
Click to collapse
It should say some thing like this:
GPRS connection to remain active once the device enters power save mode.
At least it does on the PPC 2002 latest AT&T ROM and the XDA developers Special Edition ROM v1.2. (which is bases on the O2 3.17.03 ROM).
HTH

That's really strange for my O2 xda!
I only found a setting called GPRS Suspend Mode setting.
It said,
When you are in power-saving mode, do you want to:
- Keep GPRS connection
- End GPRS connection
I clicked on the first one.
Then I close it, and connect to GPRS.
Just for a while, the connection ends by itself.
Any thought?
Thanks a lot again.

Yeap thats the correct setting and the same one I'm speaking of!
I read a lot of bad reports about the 4.21 radio stack so it might be at fault.
Maybe you should think about upgrading to the Qtec radio stack, heard nothing but good reports on that one.
The Qtek 1010 Radio Stack Upgrade can be found at:
http://www.carrierdevices.com.au/downloads.php?region=Asia Pacific
Download Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe
BTW read the WARNING.
BTW do you have a URL for that newer o2 ROM, I'd like to install it and see if it does the same for me/
HTH

Here it is.
http://www.myxda.com/web/template/SoftwareUpgradeIntroduction.vm
BTW, I am a bit nervous to install the radio file cause I have bad experience that almost kill my phone.
Is it really okay just to install the radio file?

chris_khho said:
Here it is.
http://www.myxda.com/web/template/SoftwareUpgradeIntroduction.vm
BTW, I am a bit nervous to install the radio file cause I have bad experience that almost kill my phone.
Is it really okay just to install the radio file?
Click to expand...
Click to collapse
Like I said I've heard nothing but good reports on upgrading to this radio
stack (no failed upgrades have been reported but as with any upgrade there is always a possibility). :wink:
BTW thanks for the link!
HTH

Hi Qman,
Have u tried to update that ROM?
Is there the same problem?

chris_khho said:
Hi Qman,
Have u tried to update that ROM?
Is there the same problem?
Click to expand...
Click to collapse
Unable to download, it kept asking for a IMEI.
You wouldn't happen to have the direct download link would you?

Oh! I didn't realize that...sorry.
I am still a bit nervous for upgrading (or is it actually downgrading) to the i-mat ROM.
If it is downgrading, I will definitely not try that...

Hi Qman,
I just notice that Yorch.net got the 3.20.06 ROM.
Also they have the 4.00.21 ROM (pre-release T-Mobile version). Is it for the US market only?
Chris

hi; Are you sure that Yorch.net got the 3.20.06 ROM??? Can't find it. I have downgraded my XDA yesterday from the kitchen wm2003 because of bugs to kitchen 2002 but it says 3.17.03 and not the one you mention???!!!

Hey,
That's not from the "kitchen". It's from the "upgrade" just under "kitchen". Check it out again and you will find it.
Anybody knows that 4.00.21 is good for o2 xda?
Chris

hmmm, currently I am using it
so far so good but there is one major BUT for me - most possibly that version makes wipe out my 256MB SD card every up to 48 hours
for me it is a major .... item
regards,
monika

That's terrible. What about the GPRS and phone reception?
To be honest, I won't use it if it will wipe off the sd contents every 2 days.
Have you tried to burn again?

so far GPRS is not working ....
but that is due local GSM provider that has some complicates setup as to make GPRS to work, phone recption is ok ... I am living in area where virtually all GSM phones had reception problems (i.e. majority of nokia phones), although in a city center it is perfect ....
just for you to know ... I have received a link from one of the group members for the most recent update - look there for details :
http://forum.xda-developers.com/viewtopic.php?t=4556&highlight=4+01+00
regards, monika

Thanks very much for your reply.
But I think that Upgrade exe file is for US only cause that include the radio upgrade as well.
So, are you able to downgrade your 4.00.21 easily?
I am not sure whether its worth to downgrade your device to 3.20.06 to see whether its a real problem with SD card. And to upgrade it to 4.00.21 again to verify it. It may happen only at some occasion as you know electronic device can never guarrentee functioning 100%.
Hope you can fix your device.
Cheers

New Kitchen online

Hi with the help of Lumpistefan I was able to put a new kitchen on line
the new address is
http://xda.weblink.net
please feel free to use it .
I hope thsi link will take of the load that Lumpistefan had on his line.
The sites are working in parallel mode (both get updated to each other).
Have a good cooking time :lol:

Life wasn't that nice before :lol:
Millions thanks for both of you.

hello,
thanks for the link, it works indeed.
i only have a question,
if i upgraded with the t-mobile 4.00.21 version, does it also upgrade the radio stack? does it affect my band selection?
i used the exe file.

john said:
hello,
thanks for the link, it works indeed.
i only have a question,
if i upgraded with the t-mobile 4.00.21 version, does it also upgrade the radio stack? does it affect my band selection?
i used the exe file.
Click to expand...
Click to collapse
Normally not, since there is no RSU-File included.....
HTH
Stefan

well, by me it did so,
my device suddenly changed into a B1! and gsm doesn't work anymore.
what should i do now?

john said:
well, by me it did so,
my device suddenly changed into a B1! and gsm doesn't work anymore.
what should i do now?
Click to expand...
Click to collapse
As much as i know, it's normal, that the device shows as B1 modell....
Which Radiostack are you using?

4.21.00. could be?

Not a good idea to use .exe method to upgrade, use the SD card method instead. You may need to manually change the radio to the local band by going into the bootloader and changing it to whatever it's not on now. One of the upgrades I did stopped the phone component totally and brought everything else to a standstill, but it was ten second fix.
Thanks for the new kitchen, it gives another option where there were few.

thanks, i just changed in the bootloader into GSM 900/1800. now it works, i just hope it doesn't only use the 900 and 1900(which i have no use in Europe). because in my device info it says B1 model. Maybe it's just because of the t-mobile upgrade, but doesn't REALLY change it.
let's hope.
thanks anyway.

Maybe it's just because of the t-mobile upgrade, but doesn't REALLY change it.
let's hope.
thanks anyway.
Click to expand...
Click to collapse
No, it's all sweet now. I think the configuration in the O/S changes the device configuration, so the bootloader option and the O/S option both mirror one another. As long as it works you're fine.

Great Work! Well done!

some thing on the ger image is wrong. I have after ubgrading no usb, no com1, no gsm, no light. and the sd card is unnone card ........ !!!!

mr.pommeroy said:
some thing on the ger image is wrong. I have after ubgrading no usb, no com1, no gsm, no light. and the sd card is unnone card ........ !!!!
Click to expand...
Click to collapse
Has the update run without problems?
Which German Rom are you using?
I cooked my self a 4.00.33 and it´s working fine...
Stefan

Great site and it's well done
thanks and keep up the good work.
regards
Othman

Heh, he mustn't have liked the company in the other thread he made though :shock:

i thought it was humorous that when I went to the att site on upgrade to pocket pc 2003 they referenced this formum for instruction on how to do via sd

Radio problem

Hello, my hermes has frequent disconnection ( 3G to edge - edge 3G - etc.. ) from mobile network and i cannot to receive/send call . Even when the signal seems good my phone cannot receive call. At times, when i receive a call i cannot to answer.
I have upgraded to official ROM: 2.11.258.1 ITA but the problem remain.
I have upgraded to various WM6 ( LVSW, BlackMajik, 3DES ) but the problem remain. My SN begin HT628F.... I dont' know if it is hardware or software problem.
Thanks
Giuseppe

Ciao Giuseppe...
First and foremost, upgrading to various WM6 ROMs will not help you.
Try and upgrade your radio instead. Look into the wikis for the various radios to try.
But before you do all that, I hope your device is HardSPL.
Buona fortuna =)

Dear Leo, thanks. I have upgraded any radio firmware placed in wiki but the problem remain In this moment for example signal is strenght in edge but cannot receive call . My actual ROM is 3.29.707.4 - Radio 1.27.00.00
thanks
giuseppe

Have you tried switching off WCDMA and forcing the phone to GSM only. It may be a set-up problem with the higher speed network.
Start\Settings\Phone\Band
Then select from the dropdown menus:
GSM
and/or
select the relevant bandwidth.

Thanks ach2 ! Yes i have tried this . But another problem is that i cannot to interact with setting option on the phone ! Other menu are ok , but when i select any object related to the phone there is not reply or it has very very slow or freeze
Thanks
giuseppe

joscit said:
Thanks ach2 ! Yes i have tried this . But another problem is that i cannot to interact with setting option on the phone ! Other menu are ok , but when i select any object related to the phone there is not reply or it has very very slow or freeze
Thanks
giuseppe
Click to expand...
Click to collapse
Do you have the official ITA rom on your phone now? and also did you have the same problem when you used other roms? The only thing I can think is that maybe the ITA rom disables some functions. Maybe you can try another rom, or hard reset then soft reset before the customisations start to see if you get the functions back.
I'm guessing you want the ITA rom for the language - I can't help here unless you get in touch with schaps to help him translate his great rom into italian http://forum.xda-developers.com/showthread.php?t=312604

radio problem
hi all
i think i also have the same problem. but mine's with text messaging. i can't send or receive messages flawlessly, especially when multiple messages are incoming. i can't receive all of them.
at other times, i can't send when a message is incoming, and vice versa. i'm currently using Black Majik and my radio is 1.43
thanks for any help. cheers!

Bluetooth problem; Xda Neo (Prophet)

Hello guys,
I've got a problem with my Xda Neo it's the same like Htc Prophet. I've made an upgrade to Shadow 2.0 Touchedition (WM 6.1), but when someone wants to send me something over bluetooth it doesn't work, althought I'm visible. But I can send something without any problem. I hope someone can help me. Thx

falcolombardi said:
Hello guys,
I've got a problem with my Xda Neo it's the same like Htc Prophet. I've made an upgrade to Shadow 2.0 Touchedition (WM 6.1), but when someone wants to send me something over bluetooth it doesn't work, althought I'm visible. But I can send something without any problem. I hope someone can help me. Thx
Click to expand...
Click to collapse
I think that's a ROM related issue... Try a different ROM and see if that still happens.

Ok thank you for your help. Which Rom should iI take which one do you advise?

I'd personally recommend Cloudyfas latest ROM (Build 19213). But, you may want a ROM with the Cube etc. that that ROM doesn't have.

It's ok thx you but Shadow 2.0 TE hasn't got the cube, too....

falcolombardi said:
It's ok thx you but Shadow 2.0 TE hasn't got the cube, too....
Click to expand...
Click to collapse
Then that ROM is one of the most stable...

I have installed another WM6 Rom now but there's still the same problem

falcolombardi said:
I have installed another WM6 Rom now but there's still the same problem
Click to expand...
Click to collapse
Have you checked the "Receive all incoming beams" in Settings->Connections (tab)->Beam

l3v5y said:
Have you checked the "Receive all incoming beams" in Settings->Connections (tab)->Beam
Click to expand...
Click to collapse
I think it's default setting ! . I got the same problem with my bluetooth. I can send file to Nokia N72, but can't receive anything from it, N72 says that: " Sending fail". This problem never exist in WE5, I tried some ROM 6.1 but not resolve, please check your PPC and help me !. I dont want to return WE5

Could any one confirm that HTC prophet has problem with bluetooth in WM 6.0/ 6.1 ? Can not turn it on / off ?

medkid said:
Could any one confirm that HTC prophet has problem with bluetooth in WM 6.0/ 6.1 ? Can not turn it on / off ?
Click to expand...
Click to collapse
Depends on the ROM. Some are fine, others have problems.

I had exactly the same problem. Sending via bluetooht works, but receiving not. I tried a couple of roms.
With this one I'm now able to receive files via bluetooth:
[Fixed] WM6.1 ROM - PROPHET CE OS 5.2.20226 Clean and UC
http://forum.xda-developers.com/showthread.php?t=406986
...
Fix: download link:
http://www.mediafire.com/?jotctzw0nej

Need help with the 614c

I got a few problems with my 614c!
Somehow the 3G icon always shows in the taskbar and somehow the operator is shows double first normal and later double
Could this be because of the old radio? There ws never a compatible radio update for my device.
FW 0,81
Also it seems that my ipaqs volume is very low even when all is set to maximum.....
LAst problem is that I cant start bluetooth from HTC Comm Manager but I can from the default comm manager.....
Thanx in advance for your help!!

Emrulez said:
I got a few problems with my 614c!
Somehow the 3G icon always shows in the taskbar and somehow the operator is shows double first normal and later double
Could this be because of the old radio? There ws never a compatible radio update for my device.
FW 0,81
Also it seems that my ipaqs volume is very low even when all is set to maximum.....
LAst problem is that I cant start bluetooth from HTC Comm Manager but I can from the default comm manager.....
Thanx in advance for your help!!
Click to expand...
Click to collapse
To start bluetooth from HTC CommManger you should remove this line from registry
Code:
[HKEY_LOCAL_MACHINE\Software\HTC\CommManager]
"BluetoothPlatformType"=dword:00000001
About volume, hard reset maybe needed...
With radio dont know (change from 3G mode to GSM)

sergiorus said:
To start bluetooth from HTC CommManger you should remove this line from registry
Code:
[HKEY_LOCAL_MACHINE\Software\HTC\CommManager]
"BluetoothPlatformType"=dword:00000001
About volume, hard reset maybe needed...
With radio dont know (change from 3G mode to GSM)
Click to expand...
Click to collapse
is that key in te shell registry?
will try with a new rom the volume.
How to change?
from 3g to gsm?

Emrulez said:
is that key in te shell registry?
will try with a new rom the volume.
How to change?
from 3g to gsm?
Click to expand...
Click to collapse
Hi,
Don't understand why you can't upgrade your radio. Everybody did so ... And for the 3G-GSM issue, there's this little proggie which adds a tab to your phone-settings...
Dirk

dirlan2001 said:
Hi,
Don't understand why you can't upgrade your radio. Everybody did so ... And for the 3G-GSM issue, there's this little proggie which adds a tab to your phone-settings...
Dirk
Click to expand...
Click to collapse
The original HP installer gave an error with the product ID mine wasnt compatible :s
so I dont know if ther are other ways to install a radio.
Will try the little app
thanx
EDIT: how does this app work?
EDIT: found it.

Emrulez said:
The original HP installer gave an error with the product ID mine wasnt compatible :s
so I dont know if ther are other ways to install a radio.
Will try the little app
thanx
EDIT: how does this app work?
EDIT: found it.
Click to expand...
Click to collapse
Hi again,
As far as I can remember, in the hx4700 thread has been talked about a modified hpRUU that would bypass any language incompatibility.... Maybe do a search there ?
Dirk

dirlan2001 said:
Hi again,
As far as I can remember, in the hx4700 thread has been talked about a modified hpRUU that would bypass any language incompatibility.... Maybe do a search there ?
Dirk
Click to expand...
Click to collapse
oke thanx will do, hope the radio wont screw things up as it is incompatible for a reason.
Also I have done some testing:
flashed the original dutch Rom:
Operator shows double aswell as the 3G when switched to GSM.
Flashed to keyx rom Operator shows Normal but with a 3G Icon
Flashed to my custom Rom again the double operator.
Guess the dutch OEm is bad?
Edit: Cant find the edited RUU