helloooo
tried to imei change with manipulator said it was changed but didnt when *#06# it its a uk 02 xda radio 4.16 rom 3.14.13 vers should i have used a serial lead as i used desktop charger/sync cradle to serial port
thanks neil :shock:
Related
Hello, I am reasonbly new here and I hope I did not overlooked anything what might help me with my problem.
I use the latest XDA manipulator. I made my own serial cable exactly as described. When I put my XDA into bootloader mode version 5.14 and connect, it says GSM ok. I start up on XP Proff. manipulator 1.02. Nothing is happening after this. My comport (1) is available and so on. The sw scans the ports but again nothing happened. Has it anything to do with my
radioversion 4.16?
with:
rom version 3.15.15 ENG
rom date 12/11/02
Protocol version 32S54
Thanks in advance
Erwin
Does anybody have positive feedback that XDA Manipulator works with Radio Version 4.21 and my other configuration. It's a XDA from O2 Germany.
Kind regards
xdaman
Unlocking has nothing to do with RSU ... but if your ROM has Wmodem application, why don't you try the XDAunlock tool here www.xda-developers.com/XDAunlock/
yes, it does depend on your radio version, I know it doesn't work with *.23,
the highest version that I know it will work with is *.20.
not sure about 21.
( writing '*' since the first digit of the radio version does not seem to matter, it is sometimes also '3' or '6' )
I have got two Wallaby. I bought from a guy, who killed the radio rom on a O2 XDA, bought a 1010 with a broken screen, and take the mainboard from the 1010 to the O2' case.
So I use a Qtek1010 mainboard in an O2 case.
My problem:
Booth of the devices there is a label in the back side, PW10A1. But if I go to the start->settings->device information->identify the Model No.: PW10B1
My IMEI number is equal with the IMEI printed on the 1010's case label. And as I wrote, on this label there is a PW10A1
I use Vodafone, and in my country they provide only at 1800MHz. The receive level is good, phone work well. (As I know, the PW10B1 model works on 1800MHz, but works fine at 1900MHz.)
Can I update the radio rom from here?
http://www.uspocketpcphone.com/id5.html
Thanks,
Sala
PW10A1 on the label = 900/1800.
PW10B1 on the label = 900/1900.
The probable reason for the disparity between your label id and your system id is that somebody has flashed the rom previously. The phone remains 900/1800.
Thank you!
Oh, its true.
I understand. The guy flashed with a Progamme B fro a PW10B1 device.
THX
Hello, i have MDA PW10A2 with ROM 3.16.39 ENG Radio 3.19.00.
I tried to unlock using XDAunlock but i saw only ERROR GETTING UNLOCK CODE. Is possible to unlock this version ???
B.R
simono
[email protected]
You can use the XDA-Manipulator and a serial cable, or you have to upgrade your rom to 3.17.03....
HTH
Stefan
i have only standart usb data cable
Can I upgrade software using this cable ?
B.R
simono
[email protected]
Hi,
I have a small problem and I don't know what to do.
As I disovered romkitchen I started to upgrade my qotek 1010 and now I see that on the back of my device it is written that it's a PW10A2 model and in my device information it is said that I have PW10B1.
As far sa I know PW10A2 means that I have a device 900/1800 and PW10B1 means 900/1900.
Is it very bad?
How should I deal with it?
my actual rom ver is 4.02.04 ENG and radio ver is 3.19.01 ( which I have also upgreaded before I'd read that it is better not to do so )
Thank you for all Help,
Orka
The naming in the ROM are fixed and do not depend on the real hardware settings. But that do not matter in using the device....
Stefan